Whirlpool WME 3621 X AQUA Refrigerator Program Chart

Quick START Guide
6th SENSE
This function automatically works to ensure the optimal conditions to preserve the
stored food.
The “6th Sense” function is automatically activated when:
1
2
5
3
• a large amount of food is loaded into the refrigerator
• the refrigerator door is left open for a long time
9
11
• a prolonged power failure takes place, causing the internal temperature of the
appliance to increase to values that cannot guarantee safe storage of food.
on - off
10
4
6
7
8
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Temperature button
Press the Temperature button on the control panel to adjust the temperature from the
warmest through the lower to the coldest level.
Pressing the Temperature button, the temperature setting will change cyclically.
At first plug-in of appliance temperature setpoint is present at medium position
(factory setting).
Following table shows temperature setpoints:
12
Fan*
Electronic control panel / light unit
Bottle rack*
Sensor cover
Area shelves
Rating plate with commercial name
Fruits and vegetables crisper
Door reversibility kit
Water tank
Bottle holder*
Door trays
Door seal
* Available on selected models
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts the
operation automatically. After starting the appliance, wait
at least 4-6 hours before placing food into the appliance.
When the appliance is connected to the power supply,
the display lights up and all the icons appear on the
display for approximately 1 second. The default (factory)
values of the fridge compartment settings light-up.
TEMPERATURE button.
FAST COOLING button
Led ON
Led ON
high temp.
Led OFF
med-high temp.
med-high temp.
Indicator LEDs to display the current temperature
setpoint or the Fast Cooling function.
medium temp.
FAST COOLING function
The use of the Fast Cooling function ismed-low
recommended:
temp.
- to increase the cooling speed of the refrigerator
low
temp.
compartment when placing a very high quantity of food
within it,
To activate the Fast Cooling function, press the
Temperature button cyclically on the control panel till all
the 3 LEDs blink and remain on.
REFRIGERATOR LIGHT
The light system inside the refrigerator compartment uses LEDs
light, allowing a better lightning as well as a very low energy
consumption.
If the LED light system does not work, please contact the
Service to replace it.
The function is automatically deactivated after 6 hours
and return to previous selected set point. The function can
be manually deactivated by press Temperature button on
the control panel.
Important: The refrigerator compartment light switches on
when the refrigerator door is opened. If the door is kept open for
more then 8 minutes the light will be automatically switched off.
HOW TO REVERSE THE DOOR SWING
- see enclosed Instructions for Use (Version_2)
Is recommended to reverse door swing by two persons.
There is not foreseen door reversibility for:
- models with integrated handle
- models with glass panel on the door.
medium temp.
med-low temp.
low temp.
Led ON
high temp.
Led OFF
med-high temp.
Note: Displayed set points correspond
to the average temperature
medium temp.
throughout the whole refrigerator.
med-low temp.
low temp.
ALARMS TABLE
ALARM TYPE
Signal
Cause
Cure
Door open alarm
Refrigerator Light blinks
The door has remained open for more than 5 minutes.
Close the door
Door open alarm
Refrigerator Light OFF
The door has remained open for more than 8 minutes.
Close the door
Malfunction
Any temperature indicators blinks
Product malfunction.
Contact the After-sales Service
Printed in Italy
Specifications, technical data and images may vary
from model to model
high temp.
Led OFF
FAN
The fan improves temperature distribution inside the refrigerator compartment,
allowing better preservation of stored food.
By default, the fan is switched on.
It is advisable to keep the fan switched on, so that the “6th Sense” function can work
properly and also when the ambient air temperature is above 27 - 28°C or if you
notice drops of water on the glass shelves or in sever humidity conditions.
To turn off the fan press the button of fan.
Please note that when the fan is switched on it will not continuously work. The fan
will start/stop working depending on the temperature and/or humidity level inside the
fridge.
It is therefore absolutely normal if the fan does not move even if the fan is switched
on.
05/14 - Whirlpool® Registered trademark/TM Trademark of Whirlpool group of companies - © Copyright Whirlpool Europe s.r.l. 2013. All rights reserved - http://www.whirlpool.eu
Read the Instructions for Use carefully before
using the appliance.
EN
DE GB FR
NL
ES
PT
IT
GR SE NO DK
FI
PL
CZ
SK HU
RU
BG RO
UA
KZ
5019 320 00127
Quick START Guide
EN
UTILISATION AND MAINTENANCE OF THE WATER DISPENSER AND FILTER
- (fig. 7) replace the valve cap by rotating clockwise.
Water dispenser
First use
The first time you use the water dispenser or after a long period left not used wash the tank and the filter with water. The
water dispenser provides fresh, filtered water, without the need of opening the refrigerator door. This will reduce the number
of times the door is opened, thus also reducing energy consumption of the product.
Fig. 7
Fitting and replacing the active carbon filter
The water filter should be removed from the foil bag (found in the crisper drawer (item 7). Follow the instructions provided
with the filter.
Important: If the filter is left dry for an extended period of time, its performance may be reduced. Immerse the filter in water
for a few seconds to reinstate optimum performance.
To fill the tank, rotate the cap in the direction
of the arrow
Fig. 1
Tank
Activation
device
Stop
Water drip
tray
Fig. 2
- (fig. 8) fit the tank back in place by placing it between the
lateral guides of the door and pushing it in position, ensuring
that the valve is back in its original seat. Check that the there
are no gaps between the rubber seal of the tank and the
door.
Water tank (fig. 1)
The water tank is made of antibacterial material. This prevents and
reduces the proliferation of bacteria. An internal container, with an
active carbon filtered ensures water filtration. To fill the tank: rotate the
water inlet towards you and fill with water, using a jug or other suitable
container. Once the tank is full, close the water inlet by moving it back to
its original position. Always use drinking water only: any other liquid may
impair product performance.
Fig. 8
Water Filter Duration
To ensure optimum performance you should change the water filter according with the following table:
Obtaining filtered water (fig. 2)
After filling the tank, the water may not be immediately available. This is
because the filtering process may require a few minutes (depending on
the amount of water in the tank).
To dispense water: with the refrigerator door closed, press the water
dispenser tab with the glass. If for safety reason water delivery must be
prevented, simply press the stop at the back of the tab. To release water
delivery, move the stop back to its original position. It is recommended to
drink the supplied water from the dispenser in 6 hours.
Filter duration
3,0 l/day
4,5 l/day
4 months
3 months
6,0 l/day
Cleaning the water tank (fig. 3-4-5-6-7-8)
Periodically clean the water tank with running water. Twice a year it is
recommended to keep healthy the unit using specific products based
on diluted chlorine that not modify the material properties and rinse with
current water.
To clean the tank, proceed as follows:
- (fig. 3) release and remove the water tank by lifting it and pulling towards
you. Place the tank on a flat surface, remove and wash the top cover.
Note: the tank must be refitted in its position as soon as possible,
to prevent the refrigerator from overheating.
Fig. 3
Water consumption (average)
2 months
Filter replacement is not covered by product warranty. To order more water filter cartridges, please contact your
after-sales service.
- (fig. 4) remove the internal container and the filter, and wash them
separately.
When washing the filter, only use clean water (no detergent or sharp
tools). To clean the disk filter, first remove it from the container.
Fig. 4
- (fig. 5) for a more thorough cleaning, remove the valve cap (the fitting
connecting the tank to the refrigerator) by rotating it anticlockwise.
Clean the cap. Important: do not pull on the valve body (fig. 6).
Fig. 5
Fig. 6
DE GB FR
NL
ES
PT
IT
GR SE NO DK
FI
PL
CZ
SK HU
RU
BG RO
UA
KZ
5019 320 00127

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project