Planet WAP-200N, WBS-200N User Manual

Document

Copyright



2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. To assure continued compliance, for example, use only shielded interface cables when connecting to computer or peripheral devices.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause undesired operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 21cm between the radiator and your body.

CE Compliance Statement

This device meets the RED directive 2014/53/EU of EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications in that the distance between the device and your body should not be less than 20 cm.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines must be followed at all times to ensure the safe use of the equipment.

WEEE regulation

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste; WEEE should be collected separately.

Revision

User Manual of PLANET 2.4GHz 300Mbps 802.11n Outdoor Wireless AP/CPE

Model: WAP-200N/WBS-200N

Rev: 1.0 (August, 2017)

Part No. EM-WAP-200N_WBS-200N_v1.0

Chapter 1.

Product Introduction ........................................................................................................... 7

1.1

Package Contents ............................................................................................................... 7

1.2

Product Description ............................................................................................................ 8

1.3

Product Features ............................................................................................................... 10

1.4

Product Specifications ..................................................................................................... 11

Chapter 2.

Hardware Installation ........................................................................................................ 14

2.1

Hardware Description ....................................................................................................... 14

2.1.1

The Bottom Panel ................................................................................................... 16

Chapter 3.

Connecting to the AP ........................................................................................................ 18

3.1

Preparation before Installation ........................................................................................ 18

3.1.1

Professional Installation Required .......................................................................... 18

3.1.2

Safety Precautions .................................................................................................. 18

3.2

Installation Precautions .................................................................................................... 18

3.3

Installing the AP ................................................................................................................ 20

Chapter 4.

Quick Installation Guide ................................................................................................... 22

4.1

Manual Network Setup -- TCP/IP Configuration ............................................................. 22

4.1.1

Configuring the IP Address Manually ..................................................................... 22

4.2

Starting Setup in the Web UI ............................................................................................ 25

Chapter 5.

Configuring the AP ............................................................................................................ 27

5.1

Operation Mode ................................................................................................................. 27

5.1.1

Access Point (AP) ................................................................................................... 29

5.1.2

Client Bridge (CB) ................................................................................................... 30

5.1.3

WDS Access Point (WDS AP) ................................................................................ 31

5.1.4

WDS Station (WDS STA) ........................................................................................ 32

5.1.5

WDS Bridge (WDS PtP/WDS PtMP) ...................................................................... 33

5.1.6

Client Router (CR/WISP) ........................................................................................ 39

5.1.7

Repeater ................................................................................................................. 45

5.2

Status.................................................................................................................................. 49

5.2.1

Main ........................................................................................................................ 49

5.2.2

Save/Reload ........................................................................................................... 51

5.2.3

Wireless Client List ................................................................................................. 52

5.2.4

WDS Link List ......................................................................................................... 53

5.2.5

DHCP Client Table .................................................................................................. 53

5.2.6

Connection Status ................................................................................................... 54

5.2.7

System Log ............................................................................................................. 55

5.3

System ................................................................................................................................ 56

5.3.1

IP Settings ............................................................................................................... 56

III

5.3.2

Spanning Tree Settings (STP) ................................................................................ 57

5.4

Router (WISP Mode Only) ................................................................................................. 58

5.4.1

DHCP Server Settings ............................................................................................ 58

5.4.2

WAN Settings .......................................................................................................... 59

5.4.2.1.

DHCP ............................................................................................................................. 60

5.4.2.2.

Static IP .......................................................................................................................... 61

5.4.2.3.

PPPoE ........................................................................................................................... 63

5.4.2.4.

PPTP ............................................................................................................................. 64

5.4.3

VPN Pass Through ................................................................................................. 65

5.4.4

Port Forwarding ...................................................................................................... 66

5.4.5

DMZ Settings .......................................................................................................... 67

5.5

Wireless .............................................................................................................................. 68

5.5.1

Wireless Network .................................................................................................... 68

5.5.2

WDS Link Settings .................................................................................................. 71

5.5.3

Security Settings ..................................................................................................... 73

5.5.4

Wireless MAC Filter ................................................................................................ 83

5.5.5

Wireless Advanced Settings ................................................................................... 84

5.6

Management ...................................................................................................................... 85

5.6.1

Administration (Password Settings) ........................................................................ 85

5.6.2

Management VLAN ................................................................................................ 86

5.6.3

SNMP Settings ....................................................................................................... 87

5.6.4

Backup/Restore Settings ........................................................................................ 88

5.6.5

Auto Reboot Settings .............................................................................................. 89

5.6.6

Firmware Upgrade .................................................................................................. 89

5.6.7

Time Settings .......................................................................................................... 91

5.6.8

Wi-Fi Schedule ....................................................................................................... 92

5.6.9

CLI Settings ............................................................................................................ 93

5.6.10

Log .......................................................................................................................... 93

5.6.11

Diagnostics ............................................................................................................. 94

5.6.12

Logout ..................................................................................................................... 95

Appendix A: Troubleshooting ............................................................................................................ 96

Appendix B: Use Planet Smart Discovery to find AP ...................................................................... 98

Appendix C: FAQ ................................................................................................................................. 99

Q1: How to set up the AP Client Connection ........................................................................... 99

Q2: How to set up the WDS Connection ................................................................................ 108

FIGURES

F IGURE 2-1 T HREE WAY V IEW (WAP-200N) ........................................................................................................ 14

IGURE

(WBS-200N) ........................................................................................................ 14

F IGURE 2-3 R EAR P ANEL (WAP-200N) ................................................................................................................ 15

F IGURE 2-4 R EAR P ANEL (WBS-200N) ................................................................................................................ 15

F IGURE 2-5 B OTTOM P ANEL (WAP-200N/WBS-200N) ........................................................................................ 17

F IGURE 2-6 P O E W ARNING L ABEL ....................................................................................................................... 17

F IGURE 3-1 P O E AND LAN PORT CONNECTION ..................................................................................................... 20

F IGURE 3-2 F INISH INSTALLATION AND CONNECT TO ANTENNAS (WAP-200N ONLY ) ........................................... 20

F IGURE 3-3 P OLE M OUNTING ............................................................................................................................... 21

F IGURE 3-4 W ALL M OUNTING .............................................................................................................................. 21

F IGURE 4-1 TCP/IP S ETTING ................................................................................................................................ 23

F IGURE 4-2 W INDOWS S TART M ENU .................................................................................................................... 24

F IGURE 4-3 S UCCESSFUL RESULT OF P ING COMMAND .......................................................................................... 24

F IGURE 4-4 F AILED RESULT OF P ING COMMAND ................................................................................................... 25

F IGURE 4-5 L OGIN BY DEFAULT IP ADDRESS ......................................................................................................... 25

F IGURE 4-6 L OGIN W INDOW ................................................................................................................................ 25

F IGURE 4-7 W EB UI S CREENSHOT ........................................................................................................................ 26

F IGURE 5-1 O PERATION M ODE – A LL ................................................................................................................... 28

F IGURE 5-2 O PERATION M ODE – AP ..................................................................................................................... 29

F IGURE 5-3 O PERATION M ODE – C LIENT B RIDGE ................................................................................................. 30

F IGURE 5-4 O PERATION M ODE – WDS AP ........................................................................................................... 31

F IGURE 5-5 O PERATION M ODE – WDS S TATION ................................................................................................... 32

F IGURE 5-6 O PERATION M ODE – WDS B RIDGE .................................................................................................... 33

F IGURE 5-7 O PERATION M ODE – C LIENT R OUTER (WISP) ................................................................................... 39

F IGURE 5-8 O PERATION M ODE – R EPEATER ......................................................................................................... 45

F IGURE 5-9 S YSTEM M ENU R ESET ..................................................................................................................... 49

F IGURE 5-10 S YSTEM M ENU – L ANGUAGE OPTION .............................................................................................. 49

IGURE

5-11 M

AIN

TATUS

................................................................................................................................... 50

F IGURE 5-12 S AVE /R ELOAD ................................................................................................................................. 51

F IGURE 5-13 S AVE /R ELOAD D EFAULT ................................................................................................................ 52

F IGURE 5-14 W IRELESS C LIENT L IST ................................................................................................................... 52

F IGURE 5-15 K ICK THE CLIENT ............................................................................................................................. 52

F IGURE 5-16 WDS L INK S TATUS .......................................................................................................................... 53

F IGURE 5-17 DHCP C LIENT L IST ......................................................................................................................... 53

IGURE

5-18 C

ONNECTION

TATUS

...................................................................................................................... 54

F IGURE 5-19 S YSTEM L OG ................................................................................................................................... 55

F IGURE 5-20 LAN IP S ETTINGS ............................................................................................................................ 56

F IGURE 5-21 S PANNING T REE S ETTINGS ............................................................................................................... 57

F IGURE 5-22 DHCP S ERVER S ETTINGS ................................................................................................................ 58

F IGURE 5-23 WAN S ETTINGS – A LL ..................................................................................................................... 59

F IGURE 5-24 WAN S ETTINGS – DHCP ................................................................................................................. 61

IGURE

IP ............................................................................................................ 62

F IGURE 5-26 WAN S ETTINGS – PPPOE ................................................................................................................ 63

IGURE

5-27 WAN S

ETTINGS

– PPTP .................................................................................................................. 64

F IGURE 5-28 VPN P ASS T HROUGH ....................................................................................................................... 65

F IGURE 5-29 P ORT F ORWARDING .......................................................................................................................... 66

F IGURE 5-30 P ORT F ORWARDING .......................................................................................................................... 67

F IGURE 5-31 DMZ ............................................................................................................................................... 68

F IGURE 5-32 W IRELESS N ETWORK – AP/WDS AP M ODE .................................................................................... 69

F IGURE 5-33 W IRELESS N ETWORK – SSID P ROFILE ............................................................................................. 69

F IGURE 5-34 W IRELESS N ETWORK – CB/WDS STA/CR/R EPEATER M ODE ......................................................... 71

F IGURE 5-35 WDS L INK S ETTINGS – WDS B RIDGE M ODE .................................................................................. 72

F IGURE 5-36 S ECURITY S ETTINGS – AP/WDS AP M ODE ..................................................................................... 73

F IGURE 5-37 S ECURITY S ETTINGS – CB/WDS STA/CR/R EPEATER M ODE ........................................................... 73

F IGURE 5-38 S ECURITY S ETTINGS – WDS B RIDGE M ODE .................................................................................... 74

F IGURE 5-39 S ECURITY S ETTINGS – WEP ............................................................................................................ 75

IGURE

5-40 S

ECURITY

ETTINGS

– WPA-PSK .................................................................................................... 76

F IGURE 5-41 S ECURITY S ETTINGS – WPA2-PSK .................................................................................................. 77

F IGURE 5-42 S ECURITY S ETTINGS – WPA-PSK M IXED ........................................................................................ 77

F IGURE 5-43 S ECURITY S ETTINGS – WPA (WPA E NTERPRISE ) ............................................................................. 78

F IGURE 5-44 S ECURITY S ETTINGS – WPA2 (WPA2 E NTERPRISE ) ........................................................................ 79

F IGURE 5-45 S ECURITY S ETTINGS – WPA M IXED (WPA M IXED E NTERPRISE ) ..................................................... 81

F IGURE 5-46 W IRELESS MAC F ILTER .................................................................................................................. 83

IGURE

..................................................................................................... 84

F IGURE 5-48 A DMINISTRATION (P ASSWORD S ETTINGS ) ........................................................................................ 86

F IGURE 5-49 M ANAGEMENT VLAN ..................................................................................................................... 86

F IGURE 5-50 SNMP S ETTINGS ............................................................................................................................. 87

F IGURE 5-51 B ACKUP /R ESTORE S ETTINGS ........................................................................................................... 88

F IGURE 5-52 A UTO R EBOOT S ETTINGS ................................................................................................................. 89

F IGURE 5-53 F IRMWARE U PGRADE ....................................................................................................................... 89

F IGURE 5-54 T IME S ETTINGS ................................................................................................................................ 91

F IGURE 5-55 W I -F I S CHEDULE ............................................................................................................................. 92

F IGURE 5-56 CLI S ETTINGS .................................................................................................................................. 93

F IGURE 5-57 L OG ................................................................................................................................................. 93

F IGURE 5-58 D IAGNOSTICS ................................................................................................................................... 94

F IGURE 5-59 L OGOUT ........................................................................................................................................... 95

User Manual of WAP-200N/WBS-200N

Chapter 1. Product Introduction

1.1 Package Contents

Thank you for choosing PLANET WAP-200N/WBS-200N series. Before installing the AP/CPE, please verify the contents inside the package box.

WBS-200N / WAP-200N Quick Installation Guide Mounting Strap x 2

Screw Set x 1 PoE Injector & Power Cord Antenna x 2 (WAP-200N only)

If there is any item missing or damaged, please contact the seller immediately.

-7-

User Manual of WAP-200N/WBS-200N

1.2 Product Description

Cost-effective Wireless Solution with Superior Performance

PLANET WAP-200N/WBS-200N 300Mbps 802.11n Outdoor Wireless AP/CPE offers a better range and excellent throughput. Via the WAP-200N's RP-SMA antenna connectors and the WBS-200N's embedded 8dBi dual-polarity directional antenna, it is easy to build different point to multi-point applications with good diversity coverage and better noise immunity effect, thus heightening the performance and stability of a long-distance connectivity.

Designed for Various Requirements

The WAP-200N/WBS-200N is dedicatedly designed for WISP solution that provides CPE users with Internet access via the WISP provider in rural areas. Besides, it caters to various wireless communication connectivities

(AP, Client, WDS, Repeater and WISP), thus meeting users’ application requirements.

-8-

User Manual of WAP-200N/WBS-200N

Multiple SSIDs with VLAN Tagging

Multiple SSIDs can broadcast up to four wireless networks with different names. For management purposes, the

IEEE 802.1Q VLAN supported allows multiple VLAN tags to be mapped to multiple SSIDs to distinguish the wireless access. This makes it possible for the WAP-200N/WBS-200N to work with managed Ethernet switches to have VLANs assigned for a different access level and authority.

Flexible and Reliable Outdoor Characteristics

The WAP-200N/WBS-200N is definitely suitable for wireless IP surveillance to enable to have wide deployments between buildings and to act as the backbone of public service. Additionally, its self-healing capability keeps connection alive all the time. With the IP55-rated outdoor UV-resistant enclosure, the WAP-200N/WBS-200N can perform normally under rigorous weather conditions, meaning it can be installed in any harsh, outdoor environments. With the proprietary Power over Ethernet (PoE) design, the WAP-200N/WBS-200N can be easily installed in the areas where power outlets are not available.

Advanced Security and Rigorous Authentication

The WAP-200N/WBS-200N supports 152-bit WEP, WPA/WPA2, WPA-PSK and WPA2-PSK wireless encryptions, the advanced WPA2-AES mechanism and 802.1X RADIUS authentication, which can effectively prevent eavesdropping by unauthorized users or bandwidth occupied by unauthenticated wireless access. Furthermore, any users are granted or denied access to the wireless LAN network based on the ACL (Access Control List) that the administrator pre-established.

Easy Deployment and Management

With user-friendly Web UI and comprehensive management features including client limit control and wireless traffic shaping , the WAP-200N/WBS-200N is easy to limit the client access and inbound/outbound bandwidth control, even for users who have no experience in setting up a wireless network. Furthermore, with the Planet

Smart Discovery Utility, SNMP and diagnostics tools, the WAP-200N/WBS-200N is convenient to be managed remotely.

-9-

User Manual of WAP-200N/WBS-200N

1.3 Product Features

 Industrial Compliant Wireless LAN

 Compliant with the IEEE 802.11b/g/n wireless technology

 2T2R architecture with data rate of up to 300Mbps

 Equipped with two 10/100Mbps RJ45 ports, with auto MDI/MDI-X supported

 Fixed Network Broadband Router

 Supported WAN connection types in WISP mode: DHCP, Static IP, PPPoE, PPTP

 Supports Port Forwarding and DMZ for various networking applications

 Supports DHCP server in WISP mode

 RF Interface Characteristics

 Built-in 5dBi detachable antennas with RP-SMA connectors (WAP-200N)

 Built-in 8dBi dual-polarization antenna (WBS-200N)

 High output power with multiply-adjustable transmit power control

 Outdoor Environmental Characteristics

 IP55 rating

 Passive Power over Ethernet design

 Operating temperature: -20~70°C

 Multiple Operation Modes and Wireless Features

 Multiple operation modes: AP, Client Bridge, Client Router (WISP), WDS, Repeater

 WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless

 Wireless Traffic Shaping to control the upload/download bandwidth

 Wi-Fi scheduler allows to be enabled or disabled based on predefined schedule

 Secure Network Connection

 Full encryption supported: 64-/128-/152-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X

RADIUS authentication

 Supports 802.1Q VLAN pass-through over WDS and SSID-to-VLAN mapping

 Supports up to 50 entries of MAC address filtering

 Easy Installation and Management

 IPv4/IPv6 dual-stack management networks

 Multilingual Web User Interface: English, Spanish, French, German, Portuguese, Russian, and

Simplified Chinese

 CLI command and SNMP-based management interface

 Self-healing mechanism through system auto reboot setting

 System status monitoring through remote Syslog Server and Device Discovery

 Diagnostic tools include Ping, Traceroute, Speed

 Planet Smart Discovery Utility allows administrator to discover and locate each AP

-10-

User Manual of WAP-200N/WBS-200N

1.4 Product Specifications

Product

WAP-200N WBS-200N

2.4GHz 300Mbps 802.11n Outdoor Wireless AP/CPE

Hardware Features

Standard Support

Memory

PoE

Interface

Button

IEEE802.11b/g/n

IEEE 802.3

IEEE 802.3u

IEEE 802.3x

64 Mbytes DDR SDRAM

16 Mbytes Flash

Passive PoE

Wireless IEEE 802.11b/g/n, 2T2R

PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, 24V passive PoE In

LAN 2: 1 x 10/100BASE-TX, auto-MDI/MDIX

Reset button

LED PWR, LAN, WLAN, Signal Strength

Dimensions (W x D x H)

100 x 29 x 186mm (without antennas)

100 x 29 x 380mm (with antennas)

Weight

300g (without antennas)

332g (with antennas)

Power Consumption

Power Requirements

Mounting Type

Maximum 7.2W

LAN1

 24V DC, 0.6A (Passive PoE)

 Pin 4, 5 V DC+

 Pin 7, 8 V DC-

Mast, wall mount

100 x 29 x 186mm

300g

Wireless Interface Specifications

Antenna

Data Rate

Built-in 5dBi detachable Built-in 8dBi directional antenna with dual omnidirectional antennas with RP-SMA polarization connectors

HPBW Horizontal: 360 degrees

HPBW Vertical: 30 degrees

[Port1]

HPBW Horizontal: 78 degrees

HPBW Vertical: 45 degrees

[Port2]

HPBW Horizontal: 54 degrees

HPBW Vertical: 59 degrees

IEEE 802.11b: 1, 2, 5.5, 11Mbps

IEEE 802.11g: up to 54Mbps

IEEE 802.11n (20MHz): up to 150Mbps

IEEE 802.11n (40MHz): up to 300Mbps

-11-

User Manual of WAP-200N/WBS-200N

Media Access Control CSMA/CA

Modulation

Transmission/Emission type: OFDM

Data Modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM

Frequency Band 2.412GHz ~ 2.472GHz

Operating Channel

United States -- FCC: 2.414~2.462GHz (11 channels)

Europe -- ETSI: 2.412~2.472GHz (13 channels)

RF Output Power (dBm)

FCC: IEEE 802.11b/g/n: up to 26 ± 2dBm

ETSI: IEEE 802.11b/g/n: < 20dBm (EIRP)

Receiver Sensitivity

(dBm)

IEEE 802.11b:

-95/ -93dBm (1~2/ 5.5~11Mbps)

IEEE 802.11g:

-95/ -93/ -92/ -80/ -77/ -75dBm (6/ 9~18/ 24/ 36/ 48/ 54Mbps)

IEEE 802.11n:

MCS0/ MCS8: -95dBm

MCS1/ MCS9: -93dBm

MCS2/ MCS10: -92dBm

MCS3/ MCS11: -90dBm

MCS4/ MCS12: -86dBm

MCS5/ MCS13: -83dBm

MCS6/ MCS14: -76dBm

MCS7/ MCS15: -73dBm

Environment & Certification

Operating Temperature -20~70 degrees C

Operating Humidity 10~90% (non-condensing)

IP Level

Regulatory

Software Features

IP55

CE, FCC, RoHS

LAN

WAN Connection Type

(WISP Mode only)

Wireless Modes

 Static IP

 Dynamic IP

 DHCP server in WISP mode

Supports 802.1d STP (Spanning Tree)

 Static IP

 Dynamic IP

 PPPoE

 PPTP

 Access Point

 Client Bridge

 WDS (AP/Bridge/Station)

 Client Router (WISP)/Client AP Router (WISP+AP)

 Repeater

-12-

User Manual of WAP-200N/WBS-200N

Firewall

Offers DoS protection to guard user's content network against DoS attacks

Built-in DMZ and Port Forwarding

VPN Pass-through:

 PPTP Pass-through

 L2TP Pass-through

 IPSec Pass-through

Channel Width 20MHz/40MHz

Encryption Type

Wireless Security

64-/128-/152-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X

Enable/Disable SSID Broadcast

Wireless MAC address filtering up to 50 entries

VAP Separation, Station Separation

Max. Wireless Clients Max. 64 (Suggested 32, depending on usage)

Max. SSIDs Up to 4

Max. WDS Peers Up to 4

Wireless QoS

Supports Wi-Fi Multimedia (WMM)

Supports Wireless Traffic Shaping per Radio

Wireless Advanced

Control

Status Monitoring

Auto Channel Selection

Auto Transmit Power by Regular Domains

Client Limit Control

Distance Control (Auto Ack Timeout)

Wi-Fi Schedule

Connection Status

Device Discovery, PLANET Smart Discovery

Wireless Client List/WDS Link List

VLAN

DHCP Client Table

System Log supports remote syslog server

Signal Strength LEDs in Client Bridge and WDS Station modes

VLAN pass-through over WDS

SSID-to-VLAN mapping

Self-healing

NTP

Management

Diagnostic Tools

Management VLAN (VID: 1~4094)

Supports auto reboot settings

Network Time Management

Web-based UI, CLI (Command Line Interface) supported

Configuration backup and restore

SNMP v1/v2c/v3 support, MIB I/II, Private MIB

Built-in Ping, Trace Route, Speed Test Tools

-13-

User Manual of WAP-200N/WBS-200N

Chapter 2. Hardware Installation

2.1 Hardware Description

 Dimensions (W x D x H) : 100 x 29 x 186mm (without antennas)/100 x 29 x 380mm (with 5dBi antennas)

Figure 2-1 Three-way View (WAP-200N)

Figure 2-2 Three-way View (WBS-200N)

-14-

Rear Panel – LED

User Manual of WAP-200N/WBS-200N

Figure 2-3 Rear Panel (WAP-200N)

Figure 2-4 Rear Panel (WBS-200N)

-15-

User Manual of WAP-200N/WBS-200N

LED Definition

LED

Power

LAN Ports

WLAN

State

Off

Blinking

Off

Blinking

Meaning

The device is powered on

The device is powered off

Port linked

Data is transmitting or receiving data

No link

The wireless radio is on

Data is transmitting or receiving over wireless

Off

Green LED on

The wireless radio is off

Signal is good

Orange LED on Signal is normal

Signal Strength

(Client Bridge/WDS

Station/Client Router mode only)

Red LED on Signal is poor

Table 2-1 The LED indication

2.1.1 The Bottom Panel

The Bottom panel provides the physical connectors connected to the power adapter and any other network device. Figure 2-5 shows the bottom panel of the WAP-200N/WBS-200N.

-16-

Bottom Panel

User Manual of WAP-200N/WBS-200N

PoE Warning Label

Figure 2-5 Bottom Panel (WAP-200N/WBS-200N)

Figure 2-6 PoE Warning Label

Hardware Interface Definition

Object

Antenna Connectors

(WAP-200N only)

Description

2 RP-SMA (Female) antenna connectors

Passive PoE LAN Port

LAN Port

Reset Button

10/100Mbps RJ45 port, auto MDI/MDI-X

Passive PoE/PD supported, 24V DC In

Pin assignment:

Pins 4, 5 (+)

Pins 7, 8 (-)

NOTE: Please use the 24V DC Passive PoE only (included)

10/100Mbps RJ45 port, auto MDI/MDI-X

Press and hold the Reset button on the device for over 10 seconds to return to the factory default setting.

Table 2-2 Hardware Interface Definition

-17-

User Manual of WAP-200N/WBS-200N

Chapter 3. Connecting to the AP

3.1 Preparation before Installation

3.1.1 Professional Installation Required

Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable in the local regulations.

3.1.2 Safety Precautions

1. To keep you safe and install the hardware properly, please read and follow these safety precautions.

2. If you are installing the WBS-200N or WAP-200N for the first time, for your safety as well as others’, please seek assistance from a professional installer who has received safety training on the hazards involved.

3. Keep safety as well as performance in mind when selecting your installation site, especially where there are electric power and phone lines.

4. When installing the WBS-200N or WAP-200N, please note the following things:

♦ Do not use a metal ladder;

♦ Do not work on a wet or windy day;

♦ Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.

5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the transmitter is on.

3.2 Installation Precautions

 Users MUST use a proper and well-installed surge arrestor and grounding kit with WBS-200N or

WAP-200N; otherwise, a random lightning could easily cause fatal damage to the WBS-200N or

WAP-200N. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

 Users MUST use the “Power Cord and PoE Injector” shipped in the box with the WBS-200N or

WAP-200N. Use of other options will cause damage to the WBS-200N or WAP-200N.

-18-

User Manual of WAP-200N/WBS-200N

OUTDOOR INSTALLATION WARNING

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK!

Carefully observe these instructions and any special instructions that are included with the equipment you are installing.

CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are anywhere where possible contact can be made. Antennas, masts, towers, guy wires or cables may lean or fall and contact these lines. People may be injured or killed if they are touching or holding any part of equipment when it contacts electric lines. Make sure that equipment or personnel do not come in contact directly or indirectly with power lines.

The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.

 Select equipment locations that will allow safe, simple equipment installation.

 Don’t work alone. A friend or co-worker can save your life if an accident happens.

 Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.

 If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.

 If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO

MOVE IT . Instead, save your life by calling the power company.

 Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO

ANTENNAS HAVE LIGHTNING ARRESTORS.

This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna.

 The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.

 Refer to the National Electrical Code for grounding details.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

 DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

 Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical power.

Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency medical aid has been requested.

-19-

User Manual of WAP-200N/WBS-200N

3.3 Installing the AP

Please install the AP according to the following steps. Don't forget to pull out the power plug and keep your hands dry.

Step 1. PoE and LAN port connection:

(1) Remove the bottom cover.

(2) Connect one end of the Ethernet cable into the LAN (Passive PoE) port of the device and the other end to the PoE port on the PoE Injector.

(3) Connect the power cord with the PoE Injector and plug the other end into an electrical outlet.

(4) Connect the second Ethernet cable into the LAN port of the PoE Injector and the other end to the

Ethernet port on the computer.

Figure 3-1 PoE and LAN port connection

Step 2. Attach the antennas onto the antenna connectors of the device and place the bottom cover back into the device to finish the installation.

Figure 3-2 Finish installation and connect to antennas (WAP-200N only)

-20-

User Manual of WAP-200N/WBS-200N

Step 3. Pole Mounting:

(1) Thread two mounting straps through the mounting bracket on the back of the device.

(2) Position the device on a pole and secure both mounting straps to finish the installation.

Figure 3-3 Pole Mounting

Step 4.

Wall Mounting:

(1) Secure the adhesive label to a position on the wall where you would like to install the device.

(2) Follow the plotting sticker to drill two holes and secure the plastic anchors.

(3) Align the screw holes on the mounting bracket with the screws and then install the device on the wall to finish the installation.

Figure 3-4 Wall Mounting

-21-

User Manual of WAP-200N/WBS-200N

Chapter 4. Quick Installation Guide

This chapter will show you how to configure the basic functions of your AP within minutes.

A computer with wired Ethernet connection to the Wireless AP is required for the first-time configuration.

4.1 Manual Network Setup -- TCP/IP Configuration

The default IP address of the WBS-200N and WAP-200N is 192.168.1.253

. And the default Subnet Mask is

255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.

Connect the WBS-200N or WAP-200N with your PC via an Ethernet cable which is then plugged into a LAN port of the PoE injector with one end and into a LAN port of the PC with the other end. Then power on the WBS-200N and WAP-200N via PoE injector or PoE switch.

In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7 . And the procedures in other operating systems are similar. First, make sure your Ethernet adapter is working, and refer to the Ethernet adapter’s manual if needed.

4.1.1 Configuring the IP Address Manually

Summary:

 Set up the TCP/IP Protocol for your PC.

 Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to

252), Subnet Mask is 255.255.255.0.

1 Select Use the following IP address radio button.

2 If the AP's LAN IP address is 192.168.1.253, enter IP address 192.168.1.x (x is from 2 to 254 except

192.168.1.253), and Subnet mask is 255.255.255.0.

3 Select Use the following DNS server addresses radio button. In the Preferred DNS Server field, you can enter the DNS server IP address which has been provided by your ISP

-22-

User Manual of WAP-200N/WBS-200N

Figure 4-1 TCP/IP Setting

Now click OK to save your settings.

Now, you can run the ping command in the command prompt to verify the network connection between your

PC and the AP. The following example is in Windows 7 OS. Please follow the Steps below:

1. Click on Start > Run .

2. Type “ cmd ” in the Search box.

-23-

User Manual of WAP-200N/WBS-200N

Figure 4-2 Windows Start Menu

3. Open a command prompt and type ping 192.168.1.253 , and then press Enter .

If the result displayed is similar to Figure 4-3 , it means the connection between your PC and the AP has been established well.

Figure 4-3 Successful result of Ping command

If the result displayed is similar to Figure 4-4 , it means the connection between your PC and the AP has failed.

-24-

User Manual of WAP-200N/WBS-200N

Figure 4-4 Failed result of Ping command

If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.

4.2 Starting Setup in the Web UI

It is easy to configure and manage the WBS-200N or WAP-200N with the web browser.

Step 1. To access the configuration page, open a web browser and enter the default IP address http://192.168.1.253

in the web address field of the browser.

Figure 4-5 Login by default IP address

After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.

Figure 4-6 Login Window

-25-

User Manual of WAP-200N/WBS-200N

Default IP Address: 192.168.1.253

Default User Name: admin

Default Password: admin

If the above screen does not pop up, it may mean that your web browser has been set to a proxy. Go to Tools menu> Internet Options> Connections> LAN Settings in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.

After you enter into the Web User Interface, click Operation Mode at the left hand side of the screen to configure the wireless connection. Once the basic configuration of the device is done, go to the Save/Reload page to save and apply the changes.

Figure 4-7 Web UI Screenshot

You can choose an Operation Mode according to your application. Please refer to the instructions in the next chapter for configuring different Operation Modes.

-26-

User Manual of WAP-200N/WBS-200N

Chapter 5. Configuring the AP

This chapter instructs you how to quickly configure the AP/CPE in different operation modes.

5.1 Operation Mode

On this page, you can select different operation modes of the AP depending on your application, including:

Operation Modes Description



Access Point

Client Bridge

Access Point mode is used to provide wireless connectivity to wireless clients. This mode is compatible with general wireless clients.

Client Bridge mode allows the Access Point to become a wireless client to associate to another AP thus enabling the wireless capability of wired clients.

 WDS Access Point

In WDS Access Point mode, the device functions as a WDS bridge with Access

Point Mode. For WDS Access Point, it can be connected by same series of devices which using the WDS station mode. In this mode, the setting is same as Access

Point Mode.



WDS Bridge

WDS Station

In WDS Bridge mode, the device can bridge with remote LAN networks through

MAC address. This application can create two individual networks for two groups of users sharing one Internet. The advantage of WDS is the Layer 2 transparent bridging and broadcasting across wireless connections so that all connected network devices form one common broadcast domain.

NOTE: The WDS mode is a non-standard extension to the IEEE 802.11 standard, which implemented differently in wireless driver and firmware making them incompatible with each other. In order to use WDS, the same model of devices should be used.

In WDS Station mode, the device functions as a wireless client which can bridge the remote WDS Access Point with SSID. In this mode, the setting is same as Client

Bridge mode.



Client Router

Repeater

With Client Router (Wireless ISP) mode, the device can connect to a wireless network and share the Internet connection to the WISP subscribers.

On the LAN side, the device acts like a wired router for IP sharing function. In this mode, the wireless interface acts as WAN side.

Repeater mode is used to extend the wireless coverage with same SSID and security.

Go to “ System  Operation Mode ” page to configure the device in the operation mode which is suitable for your application. Then go to “ Wireless  Wireless Network ” to configure the related wireless settings of each mode.

-27-

User Manual of WAP-200N/WBS-200N

Figure 5-1 Operation Mode – All

The page includes the following settings:

Object

•

Device Name

Green

Country/Region

Description

Enter a name for the device (1-32 characters). The name you type appears in SNMP management. This name is not the SSID and is not broadcast to other devices.

Disable the green option to enable transmit power to be configured manually. Keep it as default setting to prevent violating regional regulation unless your configuration meets the regulation.

Select a Country/Region to conform to local regulations.

•

Operation Mode

•

Save & Apply

Use the radio button to select an operation mode.

•

Cancel

Click Save & Apply to save changes.

Click Cancel to cancel the unsaved changes and revert to the previous settings.

-28-

User Manual of WAP-200N/WBS-200N

5.1.1 Access Point (AP)

This section allows you to configure the AP Bridge mode to provide wireless connectivity for wireless clients.

Go to the “ System  Operation Mode ” page to configure the device as “ Access Point ” and then go to

“ Wireless  Wireless Network ” to configure the related wireless settings.

Figure 5-2 Operation Mode – AP

For the configuration example, please refer to the section “ Appendix C: FAQ, Q1 ”.

-29-

User Manual of WAP-200N/WBS-200N

5.1.2 Client Bridge (CB)

This section allows you to configure the Client Bridge mode. In this mode, the device enables the wired client to be connected to the central site through wireless interface.

Go to the “ System  Operation Mode ” page to configure the device as “ Client Bridge ” and then go to

“ Wireless  Wireless Network ” to configure the related wireless settings.

Figure 5-3 Operation Mode – Client Bridge

For the configuration example, please refer to the section “ Appendix C: FAQ, Q1 ”.

-30-

User Manual of WAP-200N/WBS-200N

5.1.3 WDS Access Point (WDS AP)

This section allows you to configure the WDS AP mode. In this mode, the device is acting as master AP in the

WDS connection.

Go to the “ System  Operation Mode ” page to configure the device as “ WDS Access Point ” and then go to

“ Wireless  Wireless Network ” to configure the related wireless settings.

Figure 5-4 Operation Mode – WDS AP

For the configuration example, please refer to the section “ Appendix C: FAQ, Q2 ”.

-31-

User Manual of WAP-200N/WBS-200N

5.1.4 WDS Station (WDS STA)

This section allows you to configure the WDS Station mode. In this mode, the device is acting as slave AP in the

WDS connection.

Go to the “ System  Operation Mode ” page to configure the device as “ WDS Station ” and then go to

“ Wireless  Wireless Network ” to configure the related wireless settings.

Figure 5-5 Operation Mode – WDS Station

For the configuration example, please refer to the section “ Appendix C: FAQ, Q2 ”.

-32-

User Manual of WAP-200N/WBS-200N

5.1.5 WDS Bridge (WDS PtP/WDS PtMP)

This section allows you to configure the WDS Bridge mode. In this mode, the device is bridging to remote node through wireless MAC address. When suppressed SSID broadcast is checked, unknown wireless clients are not allowed to connect to the AP.

Go to the “ System  Operation Mode ” page to configure the device as “ WDS Bridge ” and then go to

“ Wireless  WDS Link Settings ” to configure the WDS bridge mode in PtP (Point to Point) or PtMP (Point to

Multiple Points) applications.

Figure 5-6 Operation Mode – WDS Bridge

Configuration Example

The following procedure will guide you to how to establish WDS connection.

Step 1 . Go to the “ Operation Mode ” page to configure the device as “ WDS Bridge ”.

-33-

User Manual of WAP-200N/WBS-200N

Step 2 . Go to the “ System  IP Settings ” page to configure LAN IP of central site and remote site. The LAN IP must be different at both sites.

In this example, the master AP at the central site is configured to

192.168.1.252 and the slave AP at remote site is configured to 192.168.1.253.

-34-

User Manual of WAP-200N/WBS-200N

Step 3 . Go to the “ Wireless  Wireless Network ” page to configure the wireless parameters of the WDS link.

In this example, we set the channel to 6 and channel width to 40MHz.

(1) Channel HT Mode: set to 40MHz for wider bandwidth to optimize performance

(2) Channel/Frequency: set to a fixed channel. For the WDS link, the fixed channel must be used.

Step 4 . Go to the “ Wireless  WDS Link Settings ” page to enter the wireless MAC of the remote node and add encryption to protect the WDS link. Click Accept to save the changes.

(1) In PtMP of the master node: enter the wireless MAC of each remote slave node up to 4 entries.

(2) In PtMP, the distance from each slave node must be configured to the actual distance from each slave node to the master node. As to the master node, it should be configured to the value of the farthest node. In PtMP application, the distance from each node to master node should not have too much deviation to ensure the connection stability.

-35-

User Manual of WAP-200N/WBS-200N

Step 5 . If the connection range exceeds 1km, go to the “ Wireless  Wireless Advanced Settings ” page to configure the distance parameter between two sites.

(3) In PtP, the distance must be configured to the same at both sites.

(4) In PtMP, the distance at each slave nodes must be configured to the actual distance from each slave node to the master node; as to the master node should be configured to the value of the farthest node. In PtMP application, the distance from each node to master node should not have too much deviation to ensure the connection stability.

-36-

User Manual of WAP-200N/WBS-200N

Step 6 . Go to the “ Status -> Save/Reload ” page to save and apply settings.

Step 7 . Repeat Steps1 to 6 for each node.

-37-

User Manual of WAP-200N/WBS-200N

Step 8 . Go to the “ Status -> WDS Link List ” page to check the connection status.

-38-

User Manual of WAP-200N/WBS-200N

5.1.6 Client Router (CR/WISP)

This section allows you to configure the Client Router (Wireless ISP) mode to enable clients to access Internet through remote wireless AP provided by ISP. In this mode, the DHCP server is enabled and able to assign IP address to local clients after the device is connected to remote wireless AP provided by ISP.

Go to the “ System  Operation Mode ” page to configure the device as “ Client Router ” and then go to

“ Wireless  Wireless Network ” to configure the related wireless settings.

Figure 5-7 Operation Mode – Client Router (WISP)

Configuration Example

The following procedure will guide you to how to establish WISP connection.

Step 1 . Go to the “ Operation Mode ” page to configure the device as “ Client Router ”.

-39-

User Manual of WAP-200N/WBS-200N

Step 2 . Go to the “ Router  LAN Settings ” page to configure LAN IP and enable the DHCP server. The LAN IP must be a different subnet from the remote wireless AP provided by ISP.

Step 3 . Go to the “ Wireless  Wireless Network ” page to click the Site Survey button to discover the root AP.

-40-

User Manual of WAP-200N/WBS-200N

Step 4 . Click the root AP as shown below and it will go back to the previous wireless network page.

Step 5 . Click the check box of the preferred BSSID and configure the encryption to be the same as the root AP.

The Repeater SSID can be modified to an easily-recognized name for wireless clients. Then, click “ Accept ” to save the configurations.

-41-

User Manual of WAP-200N/WBS-200N

Step 6 . Go to the “ Router -> WAN Settings ” page to configure WAN settings. The Internet connection type is provided by your ISP and should be configured properly. Disable “ Discard Ping on WAN ” and then you’ll be able to use ping test tool of Diagnostics page to ping DNS to ensure the WAN connection is established properly through WISP mode.

-42-

User Manual of WAP-200N/WBS-200N

Step 7 . Go to the “ Status -> Save/Reload ” page to save and apply settings.

Step 8 . Modify your PC/laptop connected to the LAN port of this client router to “ Obtain an IP address automatically ”.

-43-

User Manual of WAP-200N/WBS-200N

Step 9 . Go to “ Status -> DHCP Client Table ” to ensure your PC/laptop receives the IP automatically.

Step 10. Go to “ Status -> Connection Status ” to check whether the connection is established successfully.

-44-

User Manual of WAP-200N/WBS-200N

5.1.7 Repeater

This section allows you to configure the Repeater mode to extend the root AP’s signal coverage.

Go to the “ System  Operation Mode ” page to configure the device as “ Repeater ” and then go to “ Wireless 

Wireless Network ” to configure the related wireless settings.

Figure 5-8 Operation Mode – Repeater

Configuration Example

The following procedure will guide you to how to establish repeater connection.

Step 1 . Go to “ Operation Mode ” page to configure the device as “ Repeater ”.

-45-

User Manual of WAP-200N/WBS-200N

Step 2 . Go to the “ Wireless  Wireless Network ” page to click the Site Survey button to discover the root AP.

Step 3 . Click the root AP as shown below and it will go back to the previous wireless network page.

-46-

User Manual of WAP-200N/WBS-200N

Step 4 . Click the check box of the preferred BSSID and configure the encryption to be the same as the root AP.

The Repeater SSID can be modified to an easily-recognized name for wireless clients. Then, click “ Accept ” to save the configurations.

Step 5 . Go to the “ Status-> Save/Reload ” page to save and apply settings.

-47-

User Manual of WAP-200N/WBS-200N

Step 6 . Use a wireless client to connect to the repeater AP and ensure it is able to receive IP address from the root AP’s network.

-48-

User Manual of WAP-200N/WBS-200N

5.2 Status

This section provides the current system summary, system log and connection status including Wireless Client

List, WDS Link List, DHCP Client Table and Connection Status to assist the administrator in viewing the network status.

In the upper-right corner of each function page, you can click “ Home ” to go back to the Main page to view the current system status and click “ Reset ” to force the system to reboot or reset the device to factory defaults.

Figure 5-9 System Menu - Reset

In the upper-right corner of each function page, you can choose the Language supported in the system from the drop-down list for better user experience. Once the language is chosen, the whole web page will be translated in the language.

Figure 5-10 System Menu – Language option

5.2.1 Main

Click “ Status  Main ” to view the current system summary.

-49-

User Manual of WAP-200N/WBS-200N

Figure 5-11 Main Status

-50-

User Manual of WAP-200N/WBS-200N

The page includes the following settings:

Object

•

System Information

LAN Settings

WAN Settings

Current Wireless Settings

Description

Shows the general system information such as device name, MAC address, country, current time, and firmware version.

Shows Local Area Network settings such as the LAN IP address, subnet mask, DHCP Server, and Rx/Tx packets.

Shows Wide Area Network settings such as the MAC address, connection type, connection status, IP address, subnet mask, primary and secondary

DNS, and Rx/Tx packets.

Shows wireless information such as operation mode, wireless mode, channel bandwidth, frequency, channel, information about each SSID, security settings, and Rx/Tx packets.

5.2.2 Save/Reload

Click “ Status  Save/Reload ” and the following page will be displayed.

Figure 5-12 Save/Reload

Click Save & Apply to save and apply all configurations.

Click Revert to cancel the unsaved changes and revert to the previous settings that have been saved.

It's not necessary to save and apply the settings if unsaved changes list is empty.

-51-

User Manual of WAP-200N/WBS-200N

Figure 5-13 Save/Reload - Default

5.2.3 Wireless Client List

Click “ Status  Wireless Client List ” to view the current associated client.

Figure 5-14 Wireless Client List

The page includes the following settings:

Figure 5-15 Kick the client

Object

•

SSID:#

•

MAC Address

•

TX (Bytes)

•

RX (Bytes)

•

RSSI (dBm)

•

Kick and Ban

Description

The SSID number that the client associated to.

The MAC Address of the associated client.

The current transmit packet of the associated client.

The current received packet of the associated client.

The current signal strength of the associated client.

Click Kick to add the client to the wireless mac filtering deny list.

-52-

User Manual of WAP-200N/WBS-200N

5.2.4 WDS Link List

Click “ Status  WDS Link List ” to view the current WDS link client.

The WDS Link List is only available in WDS Bridge mode.

The page includes the following settings:

Figure 5-16 WDS Link Status

Object

•

WDS Link ID

•

MAC Address

•

Link Status

•

RSSI (dBm)

•

Refresh

Description

The sequence number of the WDS link.

The MAC Address of the associated remote node.

The current link status.

The current signal strength of the associated remote node.

Click Refresh to update the current list.

5.2.5 DHCP Client Table

Click “ Status  DHCP Client Table ” to view the current DHCP client.

The DHCP Client Table is only available in Client Router (WISP) mode.

The page includes the following settings:

Figure 5-17 DHCP Client List

Object

•

MAC Address

•

Host Name

•

Expires

Description

The MAC Address of the DHCP client.

The IP assigned to the DHCP client.

The Host Name of the DHCP client.

The Expiry time of the DHCP client.

-53-

User Manual of WAP-200N/WBS-200N

•

Revoke

•

Reserve

•

Refresh

Click Revoke to revoke the DHCP lease of the client.

Click Reserve to reserve the IP to the client.

Click Refresh to update the client list.

5.2.6 Connection Status

Click “ Status  Connection Status ” to view the current DHCP client.

The Connection Status is only available in the following operation modes:

(1) Client Bridge

(2) Client Router

(3) WDS Station

(4) Repeater

Figure 5-18 Connection Status

The page includes the following settings:

Object

•

Network Type

•

SSID

•

BSSID

•

Connection Status

•

Wireless Mode

•

Current Channel

•

Security

•

Tx Data Rates (Mbps)

Description

The current operation mode of the device.

The SSID of the connected AP.

The MAC Address of the connected AP.

The status of the connection.

The current wireless mode of the AP.

The current channel used of this connection.

The encryption method of the AP.

The current data rates of the connection.

-54-

User Manual of WAP-200N/WBS-200N

•

Current noise level

•

Signal Strength

•

Refresh

The current noise level of the connection

The current signal strength of the connected AP.

Click Refresh to update the current data.

5.2.7 System Log

Click “ Status  System Log ” to view the system log.

Figure 5-19 System Log

The page includes the following settings:

Object

•

Show log type

•

Save

Description

Select log type to filter the records.

Click Save to save the records.

•

Refresh

•

Clear

Click

Refresh

Clear

to update the current data.

to erase the records.

-55-

5.3 System

5.3.1 IP Settings

Click “ System  IP Settings ” to configure the LAN IP address.

User Manual of WAP-200N/WBS-200N

The page includes the following settings:

Figure 5-20 LAN IP Settings

Object

•

IP Network Setting

IP Address

IP Subnet Mask

•

Default Gateway

Description

Select Obtain an IP address automatically (DHCP) to receive the IP from DHCP server.

Select Specify an IP address to configure the AP to use static IP.

The LAN IP of the AP.

The default is 192.168.1.253

. You can change it according to your needs.

The LAN subnet mask of the AP.

Enter the Gateway IP address of the AP.

•

Primary DNS

•

Secondary DNS

•

Use Link-Local Address

Enter the primary DNS server of the AP.

Enter the secondary DNS server of the AP.

Click to enable a link-local address for the AP.

-56-

User Manual of WAP-200N/WBS-200N

•

IPv6 IP Address Enter the IPv6 LAN IP of the AP.

•

IPv6 Subnet Prefix Length Enter the secondary DNS server of the AP.

•

IPv6 Default Gateway

•

IPv6 Primary DNS

Enter the IPv6 Gateway IP address of the AP.

Enter the IPv6 primary DNS server of the AP.

•

IPv6 Secondary DNS

•

Accept

Enter the IPv6 secondary DNS server of the AP.

•

Cancel

Click Accept to apply the new settings.

Click Cancel to cancel the unsaved changes and revert to the previous settings.

5.3.2 Spanning Tree Settings (STP)

The Spanning Tree Settings (STP) protocol allows network to provide a redundant link in the event of a link failure. It is advised to turn on this option for multi-point bridge network to avoid network loop.

Click “ System  Spanning Tree Settings ” to enable/disable Spanning Tree Settings.

Figure 5-21 Spanning Tree Settings

The page includes the following settings:

Description Object

•

Spanning Tree Status

•

Bridge Hello Time

Bridge Max Age

Bridge Forward Delay

Click ON to enable or click OFF to disable the option.

Specify Bridge Hello Time, in seconds. This value determines how often the AP sends hello packets to communicate information about the topology throughout the entire Bridged Local Area Network.

Specify Bridge Max Age, in seconds. If another bridge in the spanning tree does not send a hello packet for a long period of time, it is assumed to be dead.

Specify Bridge Forward Delay, in seconds. Forwarding delay time is the time spent in each of the Listening and Learning states before the

-57-

•

Priority

•

Accept

•

Cancel

User Manual of WAP-200N/WBS-200N

Forwarding state is entered. This delay is provided so that when a new bridge comes onto a busy network, it looks at some traffic before participating.

Specify the Priority number. Smaller numbers have greater priority.

Click Accept to apply the setting.

Click Cancel to cancel the setting.

5.4 Router (WISP Mode Only)

5.4.1 DHCP Server Settings

Go to the “ Operation Mode ” page to configure the device as “ Client Router ” and then go to “ Router  LAN

Settings ” to configure the device’s LAN IP settings in client router mode.

On this page, enable the DHCP server to assign IP address to local wired/wireless clients after the device is connected to the remote AP supplied by wireless ISP.

Figure 5-22 DHCP Server Settings

The page includes the following settings:

Object

•

IP Address

Description

The LAN IP of the AP.

•

IP Subnet Mask

•

Use Router As DHCP

Server

•

Starting IP Address

The LAN subnet mask of the AP.

Select it to enable DHCP server. In here the device is acting as a router.

Specify the starting IP address for the DHCP range.

-58-

User Manual of WAP-200N/WBS-200N

•

Ending IP Address

•

WINS Server IP

•

Accept

•

Cancel

Specify the ending IP address for the DHCP range.

Enter the IP address of the WINS server.

Click Accept to apply the setting.

Click Cancel to cancel the setting.

5.4.2 WAN Settings

Go to the “ Operation Mode ” page to configure the device as “ Client Router ” and then go to “ Router  WAN

Settings ” to configure the device’s WAN settings in client router mode. The WAN settings should be provided by the ISP.

Figure 5-23 WAN Settings – All

The page includes the following common settings in each Internet Connection Type:

Object

•

Internet Connection Type

Description

•

DHCP: Dynamic IP addressing assigns a different IP address each time a device connects to an ISP service provider.

•

Static IP: Setting a static IP address allows an administrator to set a specific IP address for the router and guarantees that it cannot be

-59-

User Manual of WAP-200N/WBS-200N assigned a different address.

•

PPPoE: Point-to-Point Protocol over Ethernet (PPPoE) is used mainly by ISPs that provide DSL modems to connect to the Internet.

•

PPTP: The point-to-point tunneling protocol (PPTP) is used in association with virtual private networks (VPNs).

Options: This section will not be the same depending on the Internet Connection Type.

Refer to settings of each corresponding section from 5.4.2.1 to 5.4.2.4

Domain Name Server (DNS) Address

•

Get Automatically From ISP Select it to obtain the DNS automatically from the DHCP server.

•

Use These DNS Servers

Primary DNS

Select it to set up the Primary DNS and Secondary DNS servers manually.

Enter the primary DNS server address.

•

Secondary DNS Enter the secondary DNS server address.

WAN Ping

•

Discard Ping on WAN

Accept

Cancel

Check it to enable pings on the WAN interface or disable to block pings on the WAN interface.

Click Accept to apply the setting.

Click Cancel to cancel the setting.

5.4.2.1. DHCP

Select DHCP and the device will automatically obtain IP addresses, subnet masks and gateway addresses from the ISP.

-60-

User Manual of WAP-200N/WBS-200N

Figure 5-24 WAN Settings – DHCP

The page includes the following specific settings in DHCP type:

Object Description

•

Account Name (if required) Enter the account name provided by your ISP.

•

Domain Name (if required) Enter the domain name provided by your ISP.

•

MTU

The maximum transmission unit (MTU) specifies the largest packet size permitted for an internet transmission. The factory default MTU size for

DHCP is 1500. The MTU size can be set between 576 and 1500.

•

Accept Click Accept to apply the setting.

•

Cancel Click Cancel to cancel the setting.

5.4.2.2. Static IP

If your ISP offers you static IP Internet connection type, select Static IP and then enter IP address, subnet mask, primary DNS and secondary DNS information provided by ISP in the corresponding fields.

-61-

User Manual of WAP-200N/WBS-200N

Figure 5-25 WAN Settings – Static IP

The page includes the following specific settings in Static IP type:

Object Description

•

Account Name (if required) Enter the account name provided by your ISP.

•

Domain Name (if required) Enter the domain name provided by your ISP.

•

MTU

The maximum transmission unit (MTU) specifies the largest packet size permitted for an internet transmission. The factory default MTU size for static IP is 1500. The MTU size can be set between 576 and 1500.

•

IP Address Enter the device’s WAN IP address provided by ISP.

•

IP Subnet Mask

•

Gateway IP Address

•

Accept

•

Cancel

Enter the device’s WAN IP subnet mask provided by ISP.

Enter the device’s WAN Gateway IP provided by ISP.

Click

Accept

Cancel

to apply the setting.

to cancel the setting.

-62-

User Manual of WAP-200N/WBS-200N

5.4.2.3. PPPoE

Select PPPOE if ISP is using a PPPoE connection and provide you with PPPoE user name and password.

Figure 5-26 WAN Settings – PPPOE

The page includes the following specific settings in PPPoE type:

Object

•

MTU

Description

The maximum transmission unit (MTU) specifies the largest packet size permitted for an internet transmission. The factory default MTU size for

PPPoE is 1492. The MTU size can be set between 576 and 1492.

Enter the username provided by ISP. •

Login

•

Password Enter the password provided by ISP.

•

Service Name (if required) Enter the service name of an ISP (optional).

•

Connect on Demand

Select it to specify the maximum idle time. Internet connection will disconnect when it reaches the maximum idle time, but it will

-63-

•

Keep Alive

•

Accept

•

Cancel

User Manual of WAP-200N/WBS-200N automatically connect when user tries to access the network.

Select whether to keep the Internet connection always on, or enter a redial period once the internet loses connection.

Click Accept to apply the setting.

Click Cancel to cancel the setting.

5.4.2.4. PPTP

Select PPTP if ISP is using a PPTP connection.

Figure 5-27 WAN Settings – PPTP

-64-

User Manual of WAP-200N/WBS-200N

The page includes the following specific settings in PPTP type:

Object

•

MTU

IP Address

Description

The maximum transmission unit (MTU) specifies the largest packet size permitted for an internet transmission. The factory default MTU size for

PPTP is 1400. The MTU size can be set between 1200 and 1400.

Enter the device’s WAN IP address provided by ISP.

•

Subnet Mask Enter the device’s WAN IP subnet mask provided by ISP.

•

Default Gateway

•

PPTP Server

•

Username

•

Password

Enter the device’s WAN Gateway IP provided by ISP.

Enter the IP address of the PPTP server.

Enter the username provided by ISP.

•

Connect on Demand

Keep Alive

Accept

•

Cancel

Enter the password provided by ISP.

Select it to specify the maximum idle time. Internet connection will disconnect when it reaches the maximum idle time, but it will automatically connect when user tries to access the network.

Select whether to keep the Internet connection always on, or enter a redial period once the internet loses connection.

Click Accept to apply the setting.

Click Cancel to cancel the setting.

5.4.3 VPN Pass Through

VPN Pass-through allows a secure virtual private network (VPN) connection between two sites. Enabling the options on this page opens a VPN port and enables connections to pass through the AP without interruption.

Go to the “ Operation Mode ” page to configure the device as “ Client Router ” and then go to “ Router  VPN

Pass Through ” to enable VPN pass through you required in client router mode.

Figure 5-28 VPN Pass Through

-65-

User Manual of WAP-200N/WBS-200N

The page includes the following settings:

Object

•

PPTP Pass Through

Description

Check this option to enable PPTP pass-through mode.

•

L2TP Pass Through

•

IPSec Pass Through

Check this option to enable L2TP pass-through mode.

Check this option to enable IPSec pass-through mode.

•

Accept

•

Cancel

Click

Accept

Cancel

to apply the setting.

to cancel the setting.

5.4.4 Port Forwarding

Go to “ Operation Mode ” page to configure the device as “ Client Router ” and then go to “ Router  Port

Forwarding ” to enable VPN pass through you required in client router mode.

Figure 5-29 Port Forwarding

The page includes the following settings:

Object

•

Description

Displays the sequence number of the forwarded port.

•

Name

•

Protocol

Start Port

•

End Port

Displays the name of the forwarded port.

Displays the protocol to use for mapping from the following: TCP, UDP or

Both.

Displays the LAN port number that WAN client packets will be forward to.

Displays the port number that the WAN client packets are received.

•

Server IP Address Displays the IP address of the server for the forwarded port.

•

Enable

•

Modify

•

Delete

•

Add Entry

•

Accept

Click to enable or disable the forwarded port profile.

Click to modify the forwarded port profile.

Click to delete the forwarded port profile.

Click

Add Entry

Accept

to add the new forwarding rule.

to apply the setting.

-66-

User Manual of WAP-200N/WBS-200N

When clicking Add Entry , the following window will pop up and fill in the fields required to add a new forwarding rule.

Figure 5-30 Port Forwarding

The page includes the following settings:

Object

•

Service Name

Description

Enter a name for the port forwarding rule.

•

Protocol

•

Starting Port (1~65535)

Select a protocol for the application: Choices are Both, TCP and UDP.

•

Ending Port (1~65535)

IP Address

Save

•

Cancel

Enter a starting port number.

Enter an ending port number.

All ports numbers between the starting and ending ports will forward users to the IP address specified in the IP Address field.

Enter the IP address of the server computer on the LAN network where users will be redirected.

Click Save to save the new forwarding rule.

Click Cancel to cancel the setting.

5.4.5 DMZ Settings

The DMZ function allows the device to redirect all packets going to the WAN port IP address to a particular IP address on the LAN. The difference between the virtual server and the DMZ function is that a virtual server redirects a particular service or Internet application, such as FTP, to a particular LAN client or server, whereas a

DMZ redirects all packets, regardless of the service, going to the WAN IP address to a particular LAN client or server.

Go to the “ Operation Mode ” page to configure the device as “ Client Router ” and then go to “ Router  DMZ

Settings ” to enable/configure DMZ in client router mode.

-67-

User Manual of WAP-200N/WBS-200N

Figure 5-31 DMZ

The page includes the following settings:

Object

•

DMZ Hosting

Description

Select Enable DMZ to activate DMZ functionality.

•

DMZ Address Enter an IP address of a device on the LAN.

•

Accept

•

Cancel

Click

Accept

Cancel

to apply the setting.

to cancel the setting.

5.5 Wireless

This section provides wireless related settings in different operation modes.

5.5.1 Wireless Network

Click “ Wireless  Wireless Network ” to configure the wireless basic settings. The wireless settings on this page may vary according to the selected operation mode.

-68-

User Manual of WAP-200N/WBS-200N

Figure 5-32 Wireless Network – AP/WDS AP Mode

In the AP/WDS AP mode, click the Edit button on the “ Wireless Network ” page to enter the “ SSID Profile ” page to configure the SSID profile for the wireless network.

Figure 5-33 Wireless Network – SSID Profile

-69-

User Manual of WAP-200N/WBS-200N

The page includes the following settings:

Object

•

Wireless Mode

•

Channel HT Mode

Extension Channel

Channel / Frequency

Description

Wireless mode supports 802.11b/g/n mixed modes.

The default channel bandwidth is 20/40MHz. The larger the channel, the better the transmission quality and speed.

Select upper or lower channel. Your selection may affect the Auto channel function.

Select the channel and frequency appropriate you’re your country’s regulation.

•

Auto

•

AP Detection

Current Profile

Check this option to enable auto-channel selection.

AP Detection can select the best channel to use by scanning nearby areas for Access Points.

Configure up to four different SSIDs. If many client devices will be accessing the network, you can arrange the devices into SSID groups.

Click Edit to configure the profile and check whether you want to enable extra SSIDs.

SSID Profile

•

SSID

•

VLAN ID

Specify the SSID for the current profile.

•

Suppressed SSID

Station Separation

Wireless Security

Specify the VLAN tag for the current profile.

Check this option to hide the SSID from clients. If checked, the SSID will not appear in the site survey.

Click the appropriate radio button to allow or prevent communication between client devices.

Refer to section 5.5.3 Security Setting .

•

Save

•

Cancel

Click Save to save changes.

Click Cancel to cancel the unsaved changes and revert to the previous settings.

In the CB/WDS STA/CR/Repeater mode, select Security Mode on the “ Wireless Network ” page to configure the wireless security to be the same as the root AP’s security settings.

-70-

User Manual of WAP-200N/WBS-200N

Figure 5-34 Wireless Network – CB/WDS STA/CR/Repeater Mode

The page includes the following settings:

Object

•

Wireless Mode

Description

Wireless mode supports 802.11b/g/n mixed modes.

•

SSID

Site Survey

Prefer BSSID

Wireless Security

Specify the SSID if known. This field is completed automatically if you select an Access Point in the Site Survey.

Scans nearby locations for Access Points. You can select a discovered

Access Point to establish a connection.

Enter the MAC address if known. If you select an Access Point in the Site

Survey, this field is completed automatically.

Refer to section 5.5.3 Security Setting .

•

Accept Click Accept to apply the setting.

•

Cancel

Click Cancel to cancel the unsaved changes and revert to the previous settings.

5.5.2 WDS Link Settings

Go to the “ Operation Mode ” page to configure the device as “ WDS Bridge ” and then go to “ Wireless  WDS

Link Settings ” to configure the WDS link settings including PtP (Point to Point) or PtMP (Point to Multiple Points) applications.

-71-

User Manual of WAP-200N/WBS-200N

Figure 5-35 WDS Link Settings – WDS Bridge Mode

The page includes the following settings:

Object

•

Security

Description

Select the type of WDS security: None, WEP, or AES.

•

WEP Key

•

AES Passphrase

Enter the WEP key if select security as WEP.

Enter the AES passphrase if select security as AES

•

MAC Address

Enter the wireless MAC address of the AP to which you want to extend wireless connectivity.

•

Mode Select Disable or Enable to disable or enable WDS.

•

Accept

•

Cancel

Click Accept to save the settings.

Click Cancel to cancel the unsaved changes and revert to the previous settings.

NOTE:

1. The WDS link setting is only available in WDS Bridge mode and is communicating through wireless MAC address to each other by using non-standard protocol which may not be compatible with other brands/models of device. Using the same model for full compatibility is required.

2. The security setting in each site of WDS link must be the same.

3. The wireless channel must be fixed and must be the same in each site of WDS link.

-72-

User Manual of WAP-200N/WBS-200N

5.5.3 Security Settings

Go to the “ Wireless  Wireless Network ” page to configure the security settings.

In the AP/WDS AP mode, click the Edit button on the “ Wireless Network ” page to enter the “ SSID Profile ” page and configure the wireless security for the wireless network.

Figure 5-36 Security Settings – AP/WDS AP Mode

In the CB/WDS STA/CR/Repeater mode, select Security Mode on the “ Wireless Network ” page to configure the wireless security to be the same as the root AP’s security settings.

Figure 5-37 Security Settings – CB/WDS STA/CR/Repeater Mode

-73-

User Manual of WAP-200N/WBS-200N

In the WDS Bridge mode, select Security Mode on the “ WDS Link Settings ” page to configure the wireless security settings. The security settings in each site of the WDS link must be configured to the same.

Figure 5-38 Security Settings – WDS Bridge Mode

The option includes the following settings:

Object

•

Security Mode

Description

Select the suitable security mode from the drop-down list to encrypt the wireless network. The options include Disabled, WEP, WPA-PSK,

WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed . The latest

WPA2-PSK mode is strongly recommended to use.

1. The WEP and WPA/WPA2 with TKIP didn't support in pure 802.11n mode and these options will not available in pure 802.11n mode.

2. In 802.11b/g/n mixed mode, if configured the security to WEP, WPA/WPA2 with TKIP, the connection mode/speed will be changed from 802.11n to 802.11g.

 Disabled

Authentication is disabled and no password/key is required to connect to the access point.

 WEP

WEP (Wired Equivalent Privacy) is a basic encryption. For a higher level of security, consider using the WPA encryption.

-74-

User Manual of WAP-200N/WBS-200N

Figure 5-39 Security Settings – WEP

The security mode includes the following settings:

Object

•

Security Mode

Description

Select WEP from the drop-down list to configure the wireless network using WEP encryption method.

•

Auth Type Select Open System or Shared.

•

Input Type

•

Key Length

Default Key

Key1 – Key4

Save

Select an input type of Hex or ASCII.

Level of WEP encryption is applied to all WEP keys.

Select a 64-/128-/152-bit password length.

 40/64-bit: enter 10 hexadecimal digits (any combination of 0-9, a-f,

A-F and null key is not permitted) or 5 ASCII characters.

 104/128-bit: enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F and null key is not permitted) or 13 ASCII characters.

 128/152-bit: enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F and null key is not permitted) or 16 ASCII characters.

Select 1 – 4 to specify which of the four WEP keys the device uses as its default.

Specify a password for the security key index. For security, each typed character is masked by a dot.

Click Save to save the settings.

•

Cancel

Click Cancel to cancel the unsaved changes and revert to the previous settings.

-75-

User Manual of WAP-200N/WBS-200N

 WPA-PSK

Figure 5-40 Security Settings – WPA-PSK

The security mode includes the following settings:

Object Description

Select WPA-PSK from the drop-down list to configure the wireless

•

Security Mode

•

Encryption network using WPA-PSK encryption method.

Select Both, TKIP, or AES as the encryption type.

 Both: uses TKIP and AES.

 TKIP: automatic encryption with WPA-PSK; requires passphrase.

 AES: automatic encryption with WPA2-PSK; requires passphrase.

Specify the security password. For security, each typed character is

•

Passphrase masked by a dot.

•

Group Key Update Interval Specify how often, in seconds, the group key changes.

•

Save

•

Cancel

Click Save to save the settings.

Click Cancel to cancel the unsaved changes and revert to the previous settings.

 WPA2-PSK

The later WPA2 protocol features compliance with the full IEEE 802.11i standard and uses Advanced Encryption

Standard (AES) in addition to TKIP encryption protocol to guarantee better security than that provided by WEP or WPA.

-76-

User Manual of WAP-200N/WBS-200N

Figure 5-41 Security Settings – WPA2-PSK

The security mode includes the following settings:

Object Description

Select WPA2-PSK from the drop-down list to configure the wireless

•

Security Mode

•

Encryption network using WPA2-PSK encryption method.

Select Both, TKIP, or AES as the encryption type.

 Both: uses TKIP and AES.

 TKIP: automatic encryption with WPA-PSK; requires passphrase.

 AES: automatic encryption with WPA2-PSK; requires passphrase.

Specify the security password. For security, each typed character is

•

Passphrase masked by a dot.

•

Group Key Update Interval Specify how often, in seconds, the group key changes.

•

Save

•

Cancel

Click Save to save the settings.

Click Cancel to cancel the unsaved changes and revert to the previous settings.

 WPA-PSK Mixed

Figure 5-42 Security Settings – WPA-PSK Mixed

The security mode includes the following settings:

Object Description

-77-

User Manual of WAP-200N/WBS-200N

Select WPA-PSK Mixed from the drop-down list to configure the wireless

•

Security Mode

•

Encryption network using WPA-PSK Mixed encryption method.

Select Both, TKIP, or AES as the encryption type.

 Both: uses TKIP and AES.

 TKIP: automatic encryption with WPA-PSK; requires passphrase.

 AES: automatic encryption with WPA2-PSK; requires passphrase.

Specify the security password. For security, each typed character is

•

Passphrase masked by a dot.

•

Group Key Update Interval Specify how often, in seconds, the group key changes.

•

Save Click Save to save the settings.

•

Cancel

Click Cancel to cancel the unsaved changes and revert to the previous settings.

 WPA (WPA Enterprise)

Figure 5-43 Security Settings – WPA (WPA Enterprise)

The security mode includes the following settings:

Object

•

Security Mode

Encryption

Description

Select WPA from the drop-down list to configure the wireless network using WPA encryption method.

Select Both, TKIP, or AES as the encryption type.

 Both: uses TKIP and AES.

 TKIP: automatic encryption with WPA-PSK; requires passphrase.

 AES: automatic encryption with WPA2-PSK; requires passphrase.

-78-

User Manual of WAP-200N/WBS-200N

•

Radius Server

•

Radius Accounting

Specify the IP address of the RADIUS server.

•

Radius Port

Specify the port number that your RADIUS server uses for authentication.

Default port is 1812.

•

Radius Secret Specify RADIUS secret furnished by the RADIUS server.

•

Group Key Update Interval Specify how often, in seconds, the group key changes.

Select to enable or disable RADIUS accounting.

•

Radius Accounting Server Specify the IP address of the RADIUS accounting server.

•

Radius Accounting Port

Specify the port number that your RADIUS accounting server uses for authentication. Default port is 1813.

•

Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server.

•

Interim Accounting Interval Specify the interim accounting interval (60 - 600 seconds).

•

Save Click Save to save the settings.

•

Cancel

Click Cancel to cancel the unsaved changes and revert to the previous settings.

 WPA2 (WPA2 Enterprise)

Figure 5-44 Security Settings – WPA2 (WPA2 Enterprise)

-79-

User Manual of WAP-200N/WBS-200N

The security mode includes the following settings:

Object

•

Security Mode

Encryption

Description

Select WPA2 from the drop-down list to configure the wireless network using WPA2 encryption method.

Select Both, TKIP, or AES as the encryption type.

 Both: uses TKIP and AES.

 TKIP: automatic encryption with WPA-PSK; requires passphrase.

 AES: automatic encryption with WPA2-PSK; requires passphrase.

•

Radius Server Specify the IP address of the RADIUS server.

•

Radius Port

Specify the port number that your RADIUS server uses for authentication.

Default port is 1812.

•

Radius Secret Specify RADIUS secret furnished by the RADIUS server.

•

Group Key Update Interval Specify how often, in seconds, the group key changes.

•

Radius Accounting Select to enable or disable RADIUS accounting.

•

Radius Accounting Server Specify the IP address of the RADIUS accounting server.

•

Radius Accounting Port

Specify the port number that your RADIUS accounting server uses for authentication. Default port is 1813.

•

Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server.

•

Interim Accounting Interval Specify the interim accounting interval (60 - 600 seconds).

•

Save Click Save to save the settings.

•

Cancel

Click Cancel to cancel the unsaved changes and revert to the previous settings.

-80-

 WPA Mixed (WPA Mixed Enterprise)

User Manual of WAP-200N/WBS-200N

Figure 5-45 Security Settings – WPA Mixed (WPA Mixed Enterprise)

The security mode includes the following settings:

Object

•

Security Mode

Encryption

Description

Select WPA Mixed from the drop-down list to configure the wireless network using WPA Mixed encryption method.

Select Both, TKIP, or AES as the encryption type.

 Both: uses TKIP and AES.

 TKIP: automatic encryption with WPA-PSK; requires passphrase.

 AES: automatic encryption with WPA2-PSK; requires passphrase.

•

Radius Server Specify the IP address of the RADIUS server.

•

Radius Port

Specify the port number that your RADIUS server uses for authentication.

Default port is 1812.

•

Radius Secret Specify RADIUS secret furnished by the RADIUS server.

•

Group Key Update Interval Specify how often, in seconds, the group key changes.

•

Radius Accounting Select to enable or disable RADIUS accounting.

•

Radius Accounting Server Specify the IP address of the RADIUS accounting server.

•

Radius Accounting Port

Specify the port number that your RADIUS accounting server uses for authentication. Default port is 1813.

•

Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server.

-81-

User Manual of WAP-200N/WBS-200N

•

Interim Accounting Interval Specify the interim accounting interval (60 - 600 seconds).

•

Save Click Save to save the settings.

•

Cancel

Click Cancel to cancel the unsaved changes and revert to the previous settings.

-82-

User Manual of WAP-200N/WBS-200N

5.5.4 Wireless MAC Filter

Wireless MAC Filters are used to allow or deny network access to wireless clients according to their MAC addresses. You can manually add a MAC address to restrict the permission to access the device or refer to

section 5.2.3

to kick the associated client from the wireless client list.

Click “ Wireless  Wireless MAC Filter ” to configure the wireless access control settings.

Figure 5-46 Wireless MAC Filter

The page includes the following settings:

Object

•

ACL Mode

Add

Description

Determines whether network access is granted or denied to clients whose

MAC addresses appear in the MAC Address table on this page. The option includes Disable, Deny MAC in the list, or Allow MAC in the list.

Enter the wireless MAC address of the client in front of the Add button and then click Add to add the new entry to the MAC filtering list.

•

MAC Address

Displays the sequence number of the entries.

Displays the MAC Address that will be denied/allowed to access this device.

•

Delete Click Delete to remove the entry from the list.

•

Accept Click Accept to apply the setting.

-83-

User Manual of WAP-200N/WBS-200N

5.5.5 Wireless Advanced Settings

Click “ Wireless  Wireless Advanced Settings ” to configure the wireless advanced settings.

This section allows you to configure the wireless related settings to optimize the wireless network.

Figure 5-47 Wireless Advanced Settings

The page includes the following settings:

Object

•

Data Rate

Transmit Power

Description

Select a data rate from the drop-down list. The data rate affects throughput. If you select a low data rate value, for example, the throughput is reduced but the transmission distance increases. The default is “ Auto ”.

Configure the output transmission power of the device (Range:

11~29dBm). The PtP range less 1km should keep it as default and distance exceed 5km is suggested to highest value.

The option is only allowed to be configured after disabled Green option of

“ Operation Mode ” page. Keep it as default “ Auto ” setting to prevent violating regional regulation unless your configuration meets the

-84-

User Manual of WAP-200N/WBS-200N regulation.

•

RTS/CTS Threshold

•

Distance

•

Aggregation

When the length of a data packet exceeds this value, the device will send an RTS frame to the destination wireless node, and the latter will reply with a CTS frame, and thus they are ready to communicate. The default value is 2346. A small number causes RTS/CTS packets to be sent more often and consumes more bandwidth.

Specify the distance between the master AP and slave AP. Longer distances may drop high-speed connections.

A part of the 802.11n standard that allows sending multiple frames per single access to the medium by combining frames together into one larger frame. It creates the larger frame by combining smaller frames with the same physical source, destination end points, and traffic class (QoS) into one large frame with a common MAC header. This option reduces the number of packets, but increases packet sizes.

Wireless Traffic Shaping

•

Enable Traffic Shaping

Enable or disable the regulation of packet flow leaving an interface for improved QoS.

Specify the wireless transmission speed used for downloading. •

Incoming Traffic Limit

•

Outgoing Traffic Limit Specify the wireless transmission speed used for uploading.

•

Total Percentage

SSID1 to SSID4

Specify the total percentage of the wireless traffic that is shaped.

Specify the percentage of the wireless traffic that is shaped for a specific

SSID.

Client Limit: This option is only available in AP and WDS AP modes.

•

Frequency

•

Enable

Display the frequency of the device’s radio interface.

•

Max Client

Accept

•

Cancel

Click to enable the client limit function.

Specify the max. client quantity that is allowed to connect to the radio interface.

Click Accept to apply all changes.

Click Cancel to cancel the settings.

5.6 Management

On this page, you can configure the system settings for management purposes, including Management VLAN settings, Time settings, Password settings, SNMP settings, CLI settings, Wi-Fi schedule, Firmware upgrade,

Configuration backup and restore, Factory default, and Auto reboot.

5.6.1 Administration (Password Settings)

Click “ Management  Administration ” to configure username and password of the login account.

-85-

User Manual of WAP-200N/WBS-200N

Figure 5-48 Administration (Password Settings)

The page includes the following settings:

Description Object

•

New Name Enter a new username for logging in to the Web page.

•

New Password

•

Confirm Password

•

Save/Apply

•

Cancel

Enter a new password for logging in to the Web page.

Re-enter the new password for confirmation.

Click

Save/Apply

Cancel

to apply all changes.

to cancel the settings.

5.6.2 Management VLAN

Click “ Management  Management VLAN ” to configure the management VLAN settings.

Figure 5-49 Management VLAN

The page includes the following settings:

Object

•

Management VLAN ID

Description

If your network includes VLANs and if tagged packets need to pass through the Access Point, enter the VLAN ID. Otherwise, select No VLAN tag .

-86-

User Manual of WAP-200N/WBS-200N

•

Accept

•

Cancel

Click Accept to apply the changes.

Click Cancel to cancel the settings.

5.6.3 SNMP Settings

SNMP is used in network management systems to monitor network-attached devices for conditions that warrant administrative attention.

Click “ Management  SNMP Settings ” to configure SNMP settings.

The page includes the following settings:

Figure 5-50 SNMP Settings

Object

•

SNMP

Description

Enable or disable the SNMP service.

•

Contact

•

Location

•

Community Name (Read

Only)

Enter the contact details of the device.

Enter the location of the device.

Enter the password for accessing the SNMP community for read-only access.

-87-

User Manual of WAP-200N/WBS-200N

•

Community Name

(Read/Write)

•

Trap Destination Address

•

Trap Destination

Community Name

•

SNMPv3

•

User Name

•

Auth Protocol

Enter the password for accessing the SNMP community for read and write access.

Enter the IP address where SNMP traps are to be sent.

Enter the password of the SNMP trap community.

Enable or Disable the SNMPv3 feature.

Specify the username for SNMPv3.

Select the authentication protocol type: MD5 or SHA.

•

Auth Key (8-32 Characters) Specify the authentication key for authentication.

•

Priv Protocol Select the privacy protocol type: DES.

•

Priv Key (8-32 Characters) Specify the privacy key for privacy.

•

Engine ID Specify the engine ID for SNMPv3.

•

Save/Apply

•

Cancel

Click

Save/Apply

Cancel

to apply all changes.

to cancel the settings.

5.6.4 Backup/Restore Settings

Click “ Management  Backup/Restore Settings ” and the following page will be displayed.

Figure 5-51 Backup/Restore Settings

The page includes the following settings:

Object

•

Save A Copy of Current

Settings

•

Restore Saved Settings from A File

•

Revert to Factory Default

Settings

Description

Click Backup to save the current configured settings.

To restore settings that have been previously backed up, click

File to select the file, and click

Click Factory Default

Restore .

Choose

to restore the device to its factory default settings.

-88-

User Manual of WAP-200N/WBS-200N

5.6.5 Auto Reboot Settings

Click “ Management  Auto Reboot Settings ” and the following page will be displayed.

This page allows you to enable and configure system auto reboot interval. The device can regularly reboot according to the frequency in different time formats of interval.

Figure 5-52 Auto Reboot Settings

The page includes the following settings:

Object

•

Auto Reboot Settings

•

Frequency of Auto Reboot

Save/Apply

•

Cancel

Description

Select Enable from the drop-down menu to setup this function.

Select the frequency interval using the drop-down menus. The interval supported in different time formats:

•

Min: 10/20/30/40/50/60 Mins

•

Hour: 1~24 hours

•

Day: 1~31 days

•

Week: 1~5 weeks

Click Save/Apply to apply all changes.

Click Cancel to cancel the settings.

5.6.6 Firmware Upgrade

Click “ Management  Firmware Upgrade ” to upgrade the device’s firmware.

Figure 5-53 Firmware Upgrade

-89-

User Manual of WAP-200N/WBS-200N

The page includes the following settings:

Object Description

•

Current Firmware Version Click ON to enable or click OFF to disable the option.

•

Choose File

Click Choose File to locate and select the upgrade file from your local hard disk.

•

Upload Click Upload to upgrade the firmware.

Firmware Upgrade Procedure

The following procedure will guide you to how to upgrade the firmware.

Step 1 . Click the Choose File button to locate the firmware file path. Then, click the Upload button.

Step 2 . The firmware checksum information appeared to help you confirm the file is correct. Once confirmed, click the Upgrade button to begin the upgrade process.

Step 3 . Wait for the process to finish.

-90-

User Manual of WAP-200N/WBS-200N

Step 4 . When the upgrade is finished, the system will auto reboot and you can click the hyperlink “ Click here when AP is ready ” after the system restarts.

5.6.7 Time Settings

Click “ Management  Time Settings ” to configure time zone and NTP server settings to be in sync with the device’s time.

Figure 5-54 Time Settings

The page includes the following settings:

Object

•

Manually Set Date and Time

•

Automatically Get Date and

Time

Enable Daylight Saving

Description

Enter the date and time values in the date and time fields or click the

Synchronize with PC to get the date and time values from the administrator’s PC.

Select a time zone from the drop-down list and check whether you want to enter the IP address of an NTP server or use the default NTP server.

Click to enable or disable daylight savings time. Select the start and stop times from the Start Time and Stop Time dropdown lists.

•

Save/Apply Click Save/Apply to apply all changes.

•

Cancel Click Cancel to cancel the settings.

-91-

User Manual of WAP-200N/WBS-200N

5.6.8 Wi-Fi Schedule

This page allows you to configure wireless schedule. The device can regularly enable/disable Wi-Fi function according to the pre-defined schedule rules.

Click “ Management  Auto Reboot Settings ” and the following page will be displayed.

The page includes the following settings:

Figure 5-55 Wi-Fi Schedule

Object

•

Schedule Name

Description

•

Service

Day

Enter the description of the schedule service.

Select the type of schedule service, either Wireless Power ON or

Wireless Power OFF.

Select the days of the week to enable the schedule service.

•

Time of Day

•

Add

•

Cancel

Set the start time that the service is active.

Click

Add to append the schedule service to the schedule service table

Cancel to discard changes.

-92-

User Manual of WAP-200N/WBS-200N

5.6.9 CLI Settings

The command line interface (CLI) allows user to access the device through a command console, modem or

Telnet connection for configuration.

Click “ Management  CLI Settings ” to enable/disable CLI (Command Line Interface).

Figure 5-56 CLI Settings

The page includes the following settings:

Object

•

CLI

Save/Apply

Description

Select ON/OFF to enable or disable the ability to modify the device via a command line interface (CLI).

Click Save/Apply to apply all changes.

•

Cancel Click Cancel to cancel the settings.

5.6.10 Log

Click “ Management  Log ” to enable/disable system log.

Figure 5-57 Log

-93-

User Manual of WAP-200N/WBS-200N

The page includes the following settings:

Object

•

Syslog

Description

Enable or disable the syslog function.

•

Log Server IP Address

•

Local Log

Enter the IP address of the log server.

Enable or disable the local log service.

•

Save/Apply

•

Cancel

Click

Save/Apply

Cancel

to apply all changes.

to cancel the settings.

5.6.11 Diagnostics

Click “ Management  Diagnostics ” to test the connection and performance through the built-in diagnostics utilities.

Figure 5-58 Diagnostics

-94-

User Manual of WAP-200N/WBS-200N

The page includes the following settings:

Object

•

Target IP / Domain Name

Description

Enter the IP address you would like to search.

•

Ping Packet Size

•

Number of Pings

Enter the packet size of each ping.

Enter the number of times you want to ping.

•

Start Ping

•

Trace route target

•

Start Traceroute

•

Target Address

•

Time period

•

Check Interval

•

Start Speed Test

•

IPv4 Port

•

IPv6 Port

Click

Enter an IP address or domain name you want to trace.

Click

Enter the IP address of the target PC.

Enter time period for the speed test.

Enter the interval for the speed test.

Click

Start Ping to begin pinging.

Start Traceroute

Start Speed Test

to begin the traceroute operation.

to begin the speed test operation.

Displays the IPv4 port number of the device.

Displays the IPv6 port number of the device.

5.6.12 Logout

Click “ Management  Logout ” to log out the system.

Figure 5-59 Logout

The page includes the following settings:

Object

•

Description

Click OK to log out the system.

•

Cancel Click Cancel to cancel the operation.

-95-

User Manual of WAP-200N/WBS-200N

Appendix A: Troubleshooting

If you find the AP is working improperly or stop responding to you, please read this troubleshooting first before contacting the Planet Tech Support for help. Some problems can be solved by yourself within very short time.

Scenario Solution

The AP is not responding to me when I a. Please check the connection of the power cord and the want to access it by web browser.

Ethernet cable of this AP. All cords and cables should be correctly and firmly inserted to the AP. b. If all LEDs on this AP are off, please check the status of power adapter, and make sure it is correctly powered. c. You must use the same IP address section that AP uses. d. Are you using MAC or IP address filter? Try to connect the

AP by another computer and see if it works; if not, please reset the AP to the factory default settings (Press the ‘reset’ button for over 10 seconds). e. Set your computer to static IP address, and see if the

Planet Smart Discovery can find the AP or not. f. If you did a firmware upgrade and this happens, contact the

Planet Tech Support for help. g. If all the solutions above don’t work, contact Planet Tech

Support for help.

I can’t get connected to the Internet. a. Check the Internet connection status from the router that is connected with the AP. b. Please be patient. Sometimes Internet is just that slow. c. If you have connected a computer to Internet directly before, try to do that again, and check if you can get connected to Internet with your computer directly attached to the device provided by your Internet service provider. d. Check PPPoE / L2TP / PPTP user ID and password in your router again. e. Call your Internet service provider and check if there’s something wrong with their service. f. If you just can’t connect to one or more website, but you can still use other internet services, please check

URL/Keyword filter. g. Try to reset the AP and try again later. h. Reset the device provided by your Internet service provider. i. Try to use IP address instead of hostname. If you can use

IP address to communicate with a remote server, but can’t use hostname, please check DNS setting.

I can’t locate my AP by my wireless device. a. ‘Broadcast ESSID’ set to off? b. The antenna is properly secured.

-96-

User Manual of WAP-200N/WBS-200N c. Are you too far from your AP? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled.

File downloading is very slow or breaks a. Are you using QoS function? Try to disable it and try again. frequently. b. Internet is slow sometimes; try to be patient. c. Try to reset the AP and see if it’s better after that. d. Try to know what computers do on your local network. If someone’s transferring big files, other people will think

Internet is really slow. e. If this never happens before, call you Internet service provider to know if there is something wrong with their network.

I can’t log in to the web management a. Make sure you’re connecting to the correct IP address of interface; the password is wrong. the AP. b. Password is case-sensitive. Make sure the ‘Caps Lock’ light is not illuminated. c. If you really forget the password, do a hard reset.

The AP becomes hot a. This is not a malfunction, if you can keep your hand on the

AP’s case. b. If you smell something wrong or see the smoke coming out from AP or A/C power adapter, please disconnect the AP and A/C power adapter from utility power (make sure it’s safe before doing this!), and call your dealer for help.

-97-

User Manual of WAP-200N/WBS-200N

Appendix B: Use Planet Smart Discovery to find AP

To easily discover the WAP-200N/WBS-200N in your Ethernet environment, the Planet Smart Discovery Utility is an ideal solution. The utility is available at: http://www.planet.com.tw/en/product/images/48590/Planet_Utility.zip

The following instructions will guide you to how to use the Planet Smart Discovery Utility.

Step 1 . Download the Planet Smart Discovery Utility in administrator PC.

Step 2 . Execute this utility.

Step 3 . Click the “Refresh” button as shown below to update the list of the currently connected devices.

Figure B-1 PLANET Smart Discovery

Step 4.

Select the AP from the list and then click the “Connect to Device” button to link to the Web

Management Configuration page.

The fields in white background can be modified directly, and then you can apply the new setting by clicking the “ Update Device ” button.

-98-

Q1: How to set up the AP Client Connection

Topology:

User Manual of WAP-200N/WBS-200N

Appendix C: FAQ

1. Use static IP in the PCs that are connected with AP-1 (Site-1) and AP-2 (Site-2). In this case, Site-1 is

“ 192.168.1.100

”, and Site-2 is “ 192.168.1.200

”.

2. In the AP-1, go to “ System-> IP Settings ” to configure the IP address to static and different from the CPE.

-99-

User Manual of WAP-200N/WBS-200N

3. In the AP-1, go to “ System-> Operation Mode ” and set it to use “ Access Point ” mode. Then, click “ Save &

Apply ”.

4. In the AP-1, go to “ Wireless-> Wireless Network ” to configure channel and click “ Edit ” for security setting.

(1) Channel HT Mode: set to “ 40MHz ” for wider bandwidth

(2) Channel/Frequency: uncheck “ Auto ” and set to a fixed channel

-100-

User Manual of WAP-200N/WBS-200N

5. In the SSID Profile, you can configure your own SSID and Passphrase. Then, click “ Save ” to go back to the main page.

6. Click “ Accept ” to save the configurations.

-101-

User Manual of WAP-200N/WBS-200N

7. Go to the “ Status-> Save/Reload ” page to click “ Save & Apply ” to force the AP to reboot so that it can apply all configurations and take effect.

8. In the AP-2, go to “ System-> IP Settings ” to configure the IP address to static and different from the CPE.

-102-

User Manual of WAP-200N/WBS-200N

9. In the AP-2, go to “ System-> Operation Mode ” and set it to use “ Client Bridge ” mode. Then, click “ Save &

Apply ”.

10. In the AP-2, go to “ Wireless-> Wireless Network ”. Click “Site Survey” to discover the AP-1.

-103-

User Manual of WAP-200N/WBS-200N

11. Click the AP-1 to let the AP-2 to connect it. Then, it will go back to the main page.

12. Click the check box of the preferred BSSID and configure the encryption to be the same as the AP-1. Then, click “ Accept ” to save the configurations.

-104-

User Manual of WAP-200N/WBS-200N

13. Go to the “ Status-> Save/Reload ” page to click “ Save & Apply ” to force the AP to reboot so that it can apply all configurations and take effect.

14. In the AP-2, go to the “ Status-> Connection Status ” page to check whether the AP-2 is associated to the

AP-1 successfully.

-105-

User Manual of WAP-200N/WBS-200N

15. In the AP-1, go to the “ Status-> Wireless Client List ” page to check the client’s signal strength.

16. Use command line tool to ping each other to ensure the link is successfully established.

For example, from Site-1, ping 192.168.1.200; and at Site-2, ping 192.168.1.100.

-106-

User Manual of WAP-200N/WBS-200N

Attention should be paid to the following hints:

1) The encryption method must be the same at both sites if configured.

2) Both sites should be Line-of-Sight.

3) Included in the package are two 5dBi antennas for the WAP-200N only for long distance over 1km. Please connect to the 2.4GHz antennas with higher gain.

4) For PtP connection over 1km, please adjust " Distance " setting to the actual distance between both sites on the ‘both sites' setting page.

5) To adjust “ Transmit Power ”, please:

(a) Go to the " Operation Mode " page to disable the " Green " option.

(b) Go to " Wireless Advanced Settings-> Transmit Power " to manually adjust the transmit power.

-107-

User Manual of WAP-200N/WBS-200N

Q2: How to set up the WDS Connection

Topology:

1. Use static IP in the PCs that are connected with WBS-200N-1 (Site-1) and WBS-200N-2 (Site-2). In this case, Site-1 is “ 192.168.1.100

”, and Site-2 is “ 192.168.1.200

”.

2. In the AP-1, go to “ System-> IP Settings ” to configure the IP address to static and different from the CPE.

-108-

User Manual of WAP-200N/WBS-200N

3. In the AP-1, go to “ System-> Operation Mode ” and set it to use “ WDS Access Point ” mode. Then, click

“ Save & Apply ”.

4. In the AP-1, go to “ Wireless-> Wireless Network ” to configure channel and click “ Edit ” for security setting.

(1) Channel HT Mode: set to “ 40MHz ” for wider bandwidth

(2) Channel/Frequency: uncheck “ Auto ” and set to a fixed channel

-109-

User Manual of WAP-200N/WBS-200N

5. In the SSID Profile, you can configure your own SSID and Passphrase. Then, click “ Save ” to go back to the main page.

6. Click “ Accept ” to save the configurations.

-110-

User Manual of WAP-200N/WBS-200N

7. Go to the “ Status-> Save/Reload ” page to click “ Save & Apply ” to force the AP to reboot so that it can apply all configurations and take effect.

8. In the AP-2, go to “ System-> IP Settings ” to configure the IP address to static and different from the CPE.

-111-

User Manual of WAP-200N/WBS-200N

9. In the AP-2, go to “ System-> Operation Mode ” and set it to use “ WDS Station ” mode. Then, click “ Save &

Apply ”.

10. In the AP-2, go to “ Wireless-> Wireless Network ”. Click “Site Survey” to discover the AP-1.

-112-

User Manual of WAP-200N/WBS-200N

11. Click the AP-1 to let the AP-2 connect it. Then, it will go back to the main page.

12. Click the check box of the preferred BSSID and configure the encryption to be the same as the AP-1. Then, click “ Accept ” to save the configurations.

-113-

User Manual of WAP-200N/WBS-200N

13. Go to the “ Status-> Save/Reload ” page to click “ Save & Apply ” to force the AP to reboot so that it can apply all configurations and take effect.

14. In the AP-2, go to the “ Status-> Connection Status ” page to check whether the AP-2 is associated with the

AP-1 successfully.

-114-

User Manual of WAP-200N/WBS-200N

15. In the AP-1, go to the “ Status-> Wireless Client List ” page to check the client’s signal strength.

16. Use command line tool to ping each other to ensure the link is successfully established.

For example, from Site-1, ping 192.168.1.200; and at Site-2, ping 192.168.1.100.

-115-

User Manual of WAP-200N/WBS-200N

Attention should be paid to the following hints:

1) The encryption method must be the same at both sites if configured.

2) Both sites should be Line-of-Sight.

3) Included in the package are two 5dBi antennas for the WAP-200N only for long distance over 1km. Please connect to the 2.4GHz antennas with higher gain.

4) For PtP connection over 1km, please adjust " Distance " setting to the actual distance between both sites on the ‘both sites' setting page.

5) To adjust “ Transmit Power ”, please:

(a) Go to the "Operation Mode" page to disable the "Green" option.

(b) Go to the "Wireless Advanced Settings-> Transmit Power" to manually adjust the transmit power.

-116-

User Manual of WAP-200N/WBS-200N

English

Česky

Dansk

Deutsch

Eestikeele s

Ελληνικά

Español

Français

EC Declaration of Conformity

Hereby, PLANET Technology Corporation, declares that this 300Mbps 802.11n Wireless

Outdoor AP/CPE is in compliance with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

Společnost

PLANET Technology Corporation, tímto prohlašuje, že tato 300Mbps 802.11n Wireless

Outdoor AP/CPE splňuje základní požadavky a další příslušná ustanovení směrnice 1999/5/EC.

Lietuviškai

Magyar

PLANET Technology Corporation, erklærer herved, at følgende udstyr 300Mbps 802.11n

Wireless Outdoor AP/CPE overholder de væsentlige krav og øvrige relevante krav i direktiv

1999/5/EF

Hiermit erklärt PLANET Technology Corporation, dass sich dieses Gerät 300Mbps 802.11n Wireless

Outdoor AP/CPE in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten

Vorschriften der Richtlinie 1999/5/EG befindet".

(BMWi)

Käesolevaga kinnitab PLANET Technology

Corporation, et see 300Mbps 802.11n Wireless

Outdoor AP/CPE vastab Euroopa Nõukogu direktiivi

1999/5/EC põhinõuetele ja muudele olulistele tingimustele.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ

, PLANET Technology

Corporation,

ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ 300Mbps

802.11n Wireless Outdoor

AP/CPE

ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ

ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ

ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ

Por medio de la presente, PLANET Technology

Corporation, declara que 300Mbps 802.11n

Wireless Outdoor AP/CPE cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE

Par la présente, PLANET Technology Corporation, déclare que les appareils du 300Mbps 802.11n

Wireless Outdoor AP/CPE sont conformes aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE

Malti

Nederlands

Polski

Português

Slovensky

Slovensko

Šiuo kad

PLANET Technology Corporation, , skelbia,

300Mbps 802.11n Wireless Outdoor AP/CPE tenkina visus svarbiausius 1999/5/EC direktyvos reikalavimus ir kitas svarbias nuostatas.

A gyártó PLANET Technology Corporation , kijelenti, hogy ez a 300Mbps 802.11n Wireless

Outdoor AP/CPE megfelel az 1999/5/EK irányelv alapkövetelményeinek és a kapcsolódó rendelkezéseknek.

Hawnhekk, PLANET Technology Corporation, jiddikjara li dan 300Mbps 802.11n Wireless Outdoor

AP/CPE jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva

1999/5/EC

Hierbij verklaart , PLANET Technology orporation, dat 300Mbps 802.11n Wireless Outdoor AP/CPE in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG

Niniejszym firma PLANET Technology

Corporation, oświadcza, że

300Mbps 802.11n

Wireless Outdoor AP/CPE spełnia wszystkie istotne wymogi i klauzule zawarte w dokumencie „Directive

1999/5/EC”.

PLANET Technology Corporation , declara que este 300Mbps 802.11n Wireless Outdoor AP/CPE está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Výrobca PLANET Technology Corporation, týmto deklaruje, že táto 300Mbps 802.11n Wireless

Outdoor AP/CPE je v súlade so základnými požiadavkami a ďalšími relevantnými predpismi smernice 1999/5/EC.

PLANET Technology Corporation , s tem potrjuje, da je ta 300Mbps 802.11n Wireless Outdoor

AP/CPE skladen/a z osnovnimi zahtevami in ustreznimi določili Direktive 1999/5/EC.

Italiano

Latviski

Con la presente , PLANET Technology

Corporation, dichiara che questo 300Mbps 802.11n

Wireless Outdoor AP/CPE è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva

1999/5/CE.

Suomi

Ar šo PLANET Technology Corporation, apliecina, ka šī

300Mbps 802.11n Wireless Outdoor

AP/CPE atbilst Direktīvas 1999/5/EK pamatprasībām un citiem atbilstošiem noteikumiem.

Svenska

PLANET Technology Corporation, vakuuttaa täten että 300Mbps 802.11n Wireless Outdoor AP/CPE tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Härmed intygar, PLANET Technology Corporation, att denna 300Mbps 802.11n Wireless Outdoor

AP/CPE står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

-117-