Asus EX-B85M-V Manual

Add to my manuals
27 Pages

advertisement

Asus EX-B85M-V Manual | Manualzz

EX-B85M-V

ii

E10929

First Edition

March 2016

Copyright © 2016 ASUSTeK COMPUTER INC. All Rights Reserved.

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Offer to Provide Source Code of Certain Software

This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software

Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.

Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either

(1) for free by downloading it from http://support.asus.com/download or

(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc.

Legal Compliance Dept.

15 Li Te Rd.,

Beitou, Taipei 112

Taiwan

In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you.

The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code.

This offer is valid to anyone in receipt of this information.

ASUSTeK is eager to duly provide complete source code as required under various Free Open Source

Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address [email protected]

, stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address).

Contents

Safety information ...................................................................................... iv

About this guide ......................................................................................... iv

Package contents ....................................................................................... vi

EX-B85M-V specifications summary

......................................................... vi

Chapter 1

Product introduction

Motherboard overview ............................................................................. 1-1

Central Processing Unit (CPU) ................................................................ 1-7

System memory ........................................................................................ 1-8

Chapter 2

BIOS information

BIOS setup program ................................................................................. 2-1

EZ Mode ..................................................................................................... 2-2

Advanced Mode ........................................................................................ 2-3

Exit menu ................................................................................................... 2-4

Appendices

Notices .......................................................................................................A-1

ASUS contact information .......................................................................A-5

iii

iv

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.

• Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit.

• Ensure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation safety

• Before installing the motherboard and adding components, carefully read all the manuals that came with the package.

• Before using the product, ensure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may be exposed to moisture.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualified service technician or your retailer.

About this guide

This user guide contains the information you need when installing and configuring the motherboard.

How this guide is organized

This guide contains the following parts:

• Chapter 1: Product introduction

This chapter describes the features of the motherboard and the new technology it supports. It includes descriptions of the switches, jumpers, and connectors on the motherboard.

• Chapter 2: BIOS information

This chapter discusses changing system settings through the BIOS Setup menus.

Detailed descriptions for the BIOS parameters are also provided.

Where to find more information

Refer to the following sources for additional information and for product and software updates.

1. ASUS websites

The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.

2. Optional documentation

Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when completing a task.

CAUTION: Information to prevent damage to the components when completing a task

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

Typography

Bold text

Italics

<Key>

Indicates a menu or an item to select.

Used to emphasize a word or a phrase.

Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key.

Example: <Enter> means that you must press the Enter or

Return key.

<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key names are linked with a plus sign (+). v

vi

Package contents

Check your motherboard package for the following items.

Motherboard

Cables

Accessories

Application DVD

Documentation

ASUS EX-B85M-V motherboard

2 x Serial ATA 6.0 Gb/s cables

1 x I/O Shield

1 x Support CD

User Guide

If any of the above items is damaged or missing, contact your retailer.

EX-B85M-V specifications summary

CPU

Chipset

Memory

Graphics

Expansion slots

Audio

Storage

Intel ® LGA1150 socket for 4th Generation Intel ®

Pentium ® and Celeron ® processors

Core™ i7/ i5/ i3, Dual-Core

Supports 22nm CPU

Supports Intel ® Turbo Boost Technology 2.0

* The Intel ® Turbo Boost Technology 2.0 support depends on the CPU types.

** Refer to www.asus.com for Intel ® CPU support list.

Intel ® B85 Chipset

2 x DIMMs, max. 16 GB, DDR3 1600/ 1333/ 1066 MHz, non-ECC,

Dual-channel memory architecture

* Hyper DIMM support is subject to the physical characteristics of individual CPUs.

Please refer to Memory QVL (Qualified Vendors List) for details.

** Refer to www.asus.com for the Memory QVL(Qualified Vendors List).

Integrated Graphics Processor - Intel ® HD Graphics support

VGA output support: DVI

- Supports DVI with max. resolution of 1920 x 1200 @ 60Hz

- Supports Intel ® InTru™ 3D/ Quick Sync Video/ Clear Video HD Technology

Maximum UMA memory of 1024 MB

1 x PCI Express 3.0/2.0 x16 slot (@ x16 mode)

2 x PCI Express 2.0 x1 slots

Realtek ALC887 VD2 8-channel High Definition Audio CODEC

- Separates layers for left and right tracks and ensures both channels deliver consistent, equal quality.

- Audio shielding ensures precision analog/digital separation and greatly reduced multi-lateral interference

- Premium Japanese-made audio capacitors provide warm, natural and immersive sound with exceptional clarity and fidelity

- Unique de-pop circuit reduces start-up popping noise to audio outputs

* Use a chassis with HD audio module in the front panel to support an 8-channel audio output.

Intel ® B85 Chipset with Intel Rapid Storage Technology support

- 2 x Serial ATA 3.0 Gb/s connectors

- 4 x Serial ATA 6.0 Gb/s connectors

(continued on the next page)

EX-B85M-V specifications summary

LAN

USB

ASUS unique features

Rear panel

I/O ports

Realtek ® 8111GR Gigabit LAN

Intel ® B85 Chipset

- 4 x USB 3.0/ 2.0 ports (2 ports at mid-board, 2 ports at the back panel)

Intel® B85 Chipset

- 8 x USB 2.0/1.1 ports (2 ports at mid-board, 6 ports at the back panel)

Non-stop Durability

Anti-moisture coating *

- Outstanding protection against moisture and corrosion

USBGuard

- 120% higher voltage tolerance

ASUS 5X PROTECTION II

- ASUS LANGuard - Surge-protected networking

- ASUS Overvoltage Protection - World-class circuit-protecting power design

- ASUS DIGI+ VRM - Stable power supply

- ASUS DRAM Overcurrent Protection - Enhanced DRAM overcurrent protection

- ASUS Stainless Steel Back I/O - 3X more durable

Non-Stop Challenger

ASUS iCafe Labs Certified

- Proven compatibility with diskless solution

EZ DIY

UEFI BIOS EZ Mode - featuring friendly graphics user interface

- ASUS CrashFree BIOS 3

- ASUS EZ Flash 3

ASUS Q-Design

- ASUS Q-Slot

One Stop Control

- AI Suite 3

- iCafe super mode

Optimized Cooling

- ASUS Fan Xpert

* Optional feature.The coating design varies by requests.

1 x PS/2 keyboard (purple)

1 x PS/2 mouse port (green)

1 x DVI port

1 x LAN (RJ-45) port

2 x USB 3.0/ 2.0 ports

6 x USB 2.0/ 1.1 ports

3 x Audio jacks support 8-channel audio output

(continued on the next page) vii

viii

EX-B85M-V specifications summary

Internal connectors

BIOS features

Manageability

Support DVD

OS support

Form factor

1 x USB 2.0/1.1 connector supports additional 2 USB 2.0/1.1 ports

1 x USB 3.0 connector supports additional 2 USB 3.0 ports

4 x SATA 6.0 Gb/s connectors

2 x SATA 3.0 Gb/s connectors

1 x14-1 pin TPM connector

1 x CPU fan connector (4-pin)

1 x Chassis fan connectors (4-pin)

1 x Front panel audio connector

1 x 24-pin EATX power connector

1 x 8-pin EATX 12V power connector

1 x Clear CMOS header (2-pin))

1 x Speaker connector

1x S/PDIF out connector

1 x System panel connector

64 Mb Flash ROM, UEFI AMI BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.7, ACPI

4.0 a, Multi-language BIOS, ASUS EZ Flash 3, ASUS CrashFree BIOS 3

WfM 2.0, DMI 2.0, WOL by PME, PXE

Drivers

ASUS utilities

EZ Update

Windows ® 10*

Windows ® 8.1

Windows ® 8

Windows ® 7

* 64-bit supported only.

uATX Form Factor, 8.9” x 7.0” in (22.6 cm x 17.78cm)

Specifications are subject to change without notice.

Product introduction

Motherboard overview

• Unplug the power cord from the wall socket before touching any component.

1

• Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.

• Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components.

• Unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage to motherboard components.

KBMS

1

EATX12V

2

17.78cm(7.0in)

3

CPU_FAN

EX-B85M-V

4

Place this side towards the rear of the chassis

USB34

USB3_12

LGA1150

USB56

LAN_USB910

CHA_FAN

BATTERY

AUDIO

RTL

8111GR

PCIEX16_1

Super

I/O

PCIEX1_1

ALC

887-VD2

AAFP

14

PCIEX1_2

SPDIF_OUT

USB1112

TPM

13 12 11

Intel

B85

®

CLRTC

USB3_1314

SATA6G_1 SATA6G_2 SATA6G_3

10 5

F_PANEL

9 8

1

5

6

7

Scan the QR code to get the detailed pin definitions.

ASUS EX-B85M-V 1-1

1-2

ATX power connectors (24-pin EATXPWR, 8-pin EATX12V)

These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

• For a fully configured system, we recommend that you use a power supply unit

(PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 350 W.

• DO NOT forget to connect the 8-pin EATX +12V power plug. Otherwise, the system will not boot up.

• We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices or when you intend to install additional devices. The system may become unstable or may not boot up if the power is inadequate.

• If you are uncertain about the minimum power supply requirement for your system, refer to the Recommended Power Supply Wattage Calculator at http://support.

asus.com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.

CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN)

Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan of maximum 1A (12 W) fan power.

Intel ® LGA1150 CPU socket

Install Intel ® LGA1150 CPU into this surface mount LGA1150 socket, which is designed for 4th Generation Intel ® Core™ i7/ i5/ i3, Dual-Core Pentium ® and Celeron ® processors.

For more details, refer to Central Processing Unit (CPU) .

DDR3 DIMM slots

Install 1 GB, 2 GB, 4 GB, and 8 GB non-ECC DDR3 DIMMs into these DIMM sockets.

For more details, refer to System memory .

Intel ® B85 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~4)

These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA

6.0 Gb/s signal cables.

When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to

[AHCI].

Chapter 1: Product introduction

Intel ® B85 Serial ATA 3.0Gb/s connectors (7-pin SATA3G_1~2)

These connectors connect to Serial ATA 3.0 Gb/s hard disk drives via Serial ATA

3.0 Gb/s signal cables.

When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to

[AHCI].

Speaker connector (4-pin SPEAKER)

This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.

System panel connector (10-1 pin F_PANEL)

This connector supports several chassis-mounted functions.

Clear RTC RAM (2-pin CLRTC)

This header allows you to clear the CMOS RTC RAM data of the system setup information such as date, time, and system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Use a metal object such as a screwdriver to short the two pins.

3. Plug the power cord and turn ON the computer.

4. Hold down the < Del > key during the boot process and enter

BIOS setup to re-enter data.

CLRTC

PIN 1

+3V_BAT GND

If the steps above do not help, remove the onboard battery and short the two pins again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.

USB 3.0 connector (20-1 pin USB3_1314)

Connect a USB 3.0 module to this connector for additional USB 3.0 front or rear panel ports. This connector complies with USB 3.0 specifications and provide faster data transfer speeds of up to 5 Gbps, faster charging time for USB-chargeable devices, optimized power efficiency, and backward compatibility with USB 2.0.

USB 2.0 connector (10-1 pin USB1112)

Connect the USB module cable to any of this connector, then install the module to a slot opening at the back of the system chassis. This USB connector complies with

USB 2.0 specifications and support up to 480Mbps connection speed.

Digital audio connector (4-1 pin SPDIF_OUT)

This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port.

Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis.

ASUS EX-B85M-V 1-3

1-4

TPM connector (14-1 pin TPM)

This connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

Front panel audio connector (10-1 pin AAFP)

This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.

• We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.

• If you want to connect a high-definition front panel audio module to this connector, set the Front Panel Type item in the BIOS setup to [HD Audio]. If you want to connect an AC’97 front panel audio module to this connector, set the item to

[AC97]. By default, this connector is set to [HD Audio].

IRQ assignments for this motherboard

LAN

PCIE x16

PCIE x1_1

PCIE x1_2

Intel PCH SATA

Controller

HD Audio

USB2.0_1

USB2.0_2

USB3.0

-

-

-

-

A

shared shared -

B C D

shared -

-

-

shared -

-

-

-

-

-

-

-

-

-

-

E

-

shared -

-

-

-

F

-

-

-

-

-

G

-

-

-

-

-

H

-

-

-

-

-

-

-

-

shared

shared

-

shared -

shared -

-

-

-

When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.

Chapter 1: Product introduction

Rear panel connectors

1 2 3 4

11 10 9 8 7 6 5

1. PS/2 mouse port (green).

This port is for a PS/2 mouse.

2. LAN (RJ-45) port.

This port allows Gigabit connection to a Local Area Network (LAN) through a network hub.

LAN port LED indications

Activity/Link LED

Status

Off

Orange

Description

No link

Linked

Orange (Blinking) Data activity

Orange (Blinking then steady)

Ready to wake up from S5 mode

Speed LED

Status

OFF

ORANGE 100Mbps connection

GREEN

_

Description

10Mbps connection

1Gbps connection

_

Activity Link

LED

LAN port

3. Line In port (light blue) . This port connects the tape, CD, DVD player, or other audio sources.

4. Line Out port (lime).

This port connects to a headphone or a speaker. In the 4.1, 5.1 and 7.1-channel configurations, the function of this port becomes Front Speaker Out.

5. Microphone port (pink) . This port connects to a microphone.

Refer to the audio configuration table for the function of the audio ports in 2.1, 4.1, 5.1, or

7.1-channel configuration.

Audio 2.1, 4.1, 5.1, or 7.1-channel configuration

Port

Light Blue (Rear panel)

Lime (Rear panel)

Pink (Rear panel)

Lime (Front panel)

Headset

2.1-channel

Line In

Line Out

Mic In

-

4.1-channel 5.1-channel 7.1-channel

Rear Speaker Out Rear Speaker Out Rear Speaker Out

Front Speaker Out Front Speaker Out Front Speaker Out

Mic In

-

Bass/Center

-

Bass/Center

Side Speaker Out

ASUS EX-B85M-V 1-5

To configure a 7.1-channel audio output:

Use a chassis with HD audio module in the front panel to support a 7.1-channel audio output.

6. USB 2.0 ports (USB910).

These 4-pin Universal Serial Bus (USB) ports are for USB

2.0/1.1 devices.

7. USB 2.0 ports (USB56) These 4-pin Universal Serial Bus (USB) ports are for USB

2.0/1.1 devices.

8. USB 3.0 ports (USB3_12) . These 9-pin Universal Serial Bus (USB) ports are for USB

3.0/2.0 devices.

• USB 3.0 devices can only be used for data storage.

• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster and better performance from your USB 3.0 devices.

• Due to the design of the Intel ® 100 series chipset, all USB devices connected to the

USB 2.0 and USB 3.0 ports are controlled by the xHCI controller. Some legacy USB devices must update their firmware for better compatibility.

9. USB 2.0 ports (USB34).

These 4-pin Universal Serial Bus (USB) ports are for USB

2.0/1.1 devices.

10.

DVI-D port.

This port is for any DVI-D compatible device.

DVI-D can not be converted to output from RGB Signal to CRT and is not compatible with

DVI-I.

11. PS/2 keyboard port (purple).

This port is for a PS/2 keyboard.

1-6 Chapter 1: Product introduction

Central Processing Unit (CPU)

This motherboard comes with a surface mount LGA1150 socket designed for 4th Generation Intel ® Core™ i7/ i5/ i3, Dual-Core Pentium ® and

Celeron ® processors.

Unplug all power cables before installing the CPU.

• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.

• Keep the cap after installing the motherboard. ASUS will process Return Merchandise

Authorization (RMA) requests only if the motherboard comes with the cap on the

LGA1150 socket.

• The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap.

Installing the CPU

1

A

B

3

2

4

A

C

4

5

D 5

B

4

Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary.

ASUS EX-B85M-V 1-7

1-8

System memory

Overview

This motherboard comes with two Double Data Rate 3 (DDR3) Dual Inline Memory Module

(DIMM) sockets. The figure illustrates the location of the DDR3 DIMM sockets:

DIMM_A1

DIMM_B1

Channel

Channel A

Channel B

Sockets

DIMM_A1

DIMM_B1

• You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.

• Due to Intel ® chipset limitations, DDR3 1600 MHz and higher memory modules on

XMP mode will run at the maximum transfer rate of DDR3 1600MHz.

• Always install DIMMs with the same CAS latency. For optimal compatibility, we recommend that you install memory modules of the same version or date code (D/C) from the same vendor. Check with the retailer to get the correct memory modules.

• According to Intel ® CPU spec, DIMM voltage below 1.65V is recommended to protect the CPU.

• Due to the memory address limitation on 32-bit Windows ® OS, when you install 4GB or more memory on the motherboard, the actual usable memory for the OS can be about 3GB or less. For effective use of memory, we recommend that you do any of the following:

- Use a maximum of 3GB system memory if you are using a 32-bit Windows ® OS.

- Install a 64-bit Windows ® OS if you want to install 4GB or more on the motherboard.

- For more details, refer to the Microsoft ® support site at http://support.microsoft.

com/kb/929605/en-us.

• This motherboard does not support DIMMs made up of 512 megabits (Mb) chips or less.

• Memory modules with memory frequency higher than 2133 MHz and its corresponding timing or the loaded X.M.P. Profile is not the JEDEC memory standard. The stability and compatibility of these memory modules depend on the CPU’s capabilities and other installed devices.

• The default memory operation frequency is dependent on its Serial Presence Detect

(SPD), which is the standard way of accessing information from a memory module.

Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value.

• For system stability, use a more efficient memory cooling system to support a full memory load (2 DIMMs).

• Refer to www.asus.com

for the latest Memory QVL (Qualified Vendors List)

Chapter 1: Product introduction

Installing a DIMM

1

2

3

To remove a DIMM

A

B

ASUS EX-B85M-V

A

1-9

2-1

BIOS information

2

• Scan the QR code to view the BIOS update guide.

• Before using the ASUS CrashFree BIOS 3 utility, rename the

BIOS file in the removable device into EXB85MV.CAP

.

BIOS setup program

Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS screens include navigation keys and brief online help to guide you in using the BIOS Setup program.

Entering BIOS Setup at startup

To enter BIOS Setup at startup:

Press <Delete> or <F2> during the Power-On Self Test (POST). If you do not press <Delete> or <F2>, POST continues with its routines.

Entering BIOS Setup after POST

To enter BIOS Setup after POST:

• Press <Ctrl>+<Alt>+<Del> simultaneously.

Press the reset button on the system chassis.

Press the power button to turn the system off then back on. Do this option only if you failed to enter BIOS Setup using the first two options.

Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from a running operating system can cause damage to your data or system. We recommend you always shut down the system properly from the operating system.

• The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.

• Visit the ASUS website at www.asus.com

to download the latest BIOS file for this motherboard.

• If the system becomes unstable after changing any BIOS setting, load the default settings to ensure system compatibility and stability. Select the Load Optimized

Defaults item under the Exit menu or press hotkey F5.

• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and reset the motherboard to the default value. See section Motherboard overview for information on how to erase the RTC RAM.

BIOS menu screen

The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode .

ASUS EX-B85M-V

EZ Mode

By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ

Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode, fan profile and boot device priority. To access the Advanced Mode, click Advanced Mode(F7) or press <F7>.

The default screen for entering the BIOS setup program can be changed.

Displays the CPU temperature, CPU voltage output, DRAM information and

CPU/chassis fan speed

Selects the display language of the BIOS setup program

Exits the BIOS setup program without saving the changes, saves the changes and rests the system, or enters the Advanced Mode

Selects the

Advanced mode functions

Selects the boot device priority

Power saving mode

Displays the

Advanced mode menus

SATA information

Normal mode

Selects the boot device priority

ASUS Optizimal mode

Loads optimized default settings

Displays the system properties of the selected mode on the left hand side

The boot device options vary depending on the devices you installed to the system.

Chapter 2: Getting started 2-2

Advanced Mode

The Advanced Mode provides advanced options for experienced end-users to configure the

BIOS settings. The figure below shows an example of the Advanced Mode . Refer to the following sections for the detailed configurations.

To access the EZ Mode, click Exit and then select ASUS EZ Mode .

Menu bar

Sub-menu item

Menu items

Popup window

Configuration fields

Scroll bar

Quick Note

Navigation keys

Last modified settings

2-3 ASUS EX-B85M-V

Exit menu

The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items.

Load Optimized Defaults

This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears.

Select OK to load the default values.

Save Changes & Reset

Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved. When you select this option or if you press <F10>, a confirmation window appears. Select OK to save changes and exit.

Discard Changes and Exit

This option allows you to exit the Setup program without saving your changes. When you select this option or if you press <Esc>, a confirmation window appears. Select OK to discard changes and exit.

ASUS EZ Mode

This option allows you to access the EZ Mode. See section EZ Mode for details.

Launch EFI Shell from USB drives

This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of the available USB devices.

Chapter 2: Getting started 2-4

Appendices

Appendices

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

A-1 ASUS EX-B85M-V

IC: Canadian Compliance Statement

Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS

210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Cut appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes :

(1) cet appareil ne doit pas provoquer d’interférences et

(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

This class B digital apparatus complies with Canadian ICES-003.

VCCI: Japan Compliance Statement

Class B ITE

This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

KC: Korea Warning Statement

Appendices A-2

REACH

Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of

Chemicals) regulatory framework, we published the chemical substances in our products at

ASUS REACH website at http://csr.asus.com/english/REACH.htm.

DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

Google™ License Terms

Copyright© 2016 Google Inc. All Rights Reserved.

Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file except in compliance with the License. You may obtain a copy of the License at: http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the

License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF

ANY KIND, either express or implied.

See the License for the specific language governing permissions and limitations under the

License.

A-3 ASUS EX-B85M-V

English AsusTek Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of CE Directives.

Please see the CE Declaration of Conformity for more details.

Français AsusTek Inc. déclare par la présente que cet appareil est conforme aux critères essentiels et autres clauses pertinentes des directives européennes. Veuillez consulter la déclaration de conformité CE pour plus d’informations.

Deutsch AsusTek Inc. erklärt hiermit, dass dieses Gerät mit den wesentlichen Anforderungen und anderen relevanten Bestimmungen der

CE-Richtlinien übereinstimmt. Weitere Einzelheiten entnehmen Sie bitte der

CE-Konformitätserklärung.

Italiano AsusTek Inc. con la presente dichiara che questo dispositivo

è conforme ai requisiti essenziali e alle altre disposizioni pertinenti alle direttive CE. Per maggiori informazioni fate riferimento alla dichiarazione di conformità CE.

Русский Компания ASUS заявляет, что это устройство соответствует основным требованиям и другим соответствующим условиям европейских директив. Подробную информацию, пожалуйста, смотрите в декларации соответствия.

Български С настоящото AsusTek Inc. декларира, че това устройство е в съответствие със съществените изисквания и другите приложими постановления на директивите CE. Вижте CE декларацията за съвместимост за повече информация.

Hrvatski AsusTek Inc. ovim izjavljuje da je ovaj uređaj sukladan s bitnim zahtjevima i ostalim odgovarajućim odredbama CE direktiva. Više pojedinosti potražite u CE izjavi o sukladnosti.

Čeština Společnost AsusTek Inc. tímto prohlašuje, že toto zařízení splňuje základní požadavky a další příslušná ustanovení směrnic CE. Další podrobnosti viz Prohlášení o shodě CE.

Dansk AsusTek Inc. Erklærer hermed, at denne enhed er i overensstemmelse med hovedkravene and andre relevante bestemmelser i

CE-direktiverne. Du kan læse mere i CE-overensstemmelseserklæring.

Nederlands AsusTek Inc. verklaart hierbij dat dit apparaat compatibel is met de essentiële vereisten en andere relevante bepalingen van CErichtlijnen. Raadpleeg de CE-verklaring van conformiteit voor meer details.

Eesti Käesolevaga kinnitab AsusTek Inc., et see seade vastab CE direktiivide oluliste nõuetele ja teistele asjakohastele sätetele. Vt üksikasju CE vastavusdeklaratsioonist.

Suomi AsusTek Inc. vakuuttaa täten, että tämä laite on CE-direktiivien olennaisten vaatimusten ja muiden asiaan kuuluvien lisäysten mukainen.

Katso lisätietoja CE-vaatimustenmukaisuusvakuutuksesta.

Ελληνικά Με το παρόν, η AsusTek Inc. Δηλώνει ότι αυτή η συσκευή

συμμορφώνεται με τις θεμελιώδεις απαιτήσεις και άλλες σχετικές διατάξεις

των Οδηγιών της ΕΕ. Για περισσότερες λεπτομέρειες ανατρέξτε στην

Δήλωση Συμμόρφωσης ΕΕ.

Magyar Az AsusTek Inc. ezennel kijelenti, hogy a készülék megfelel a CE-irányelvek alapvető követelményeinek és ide vonatkozó egyéb rendelkezéseinek. További részletekért tekintse meg a CE-megfelelőségi nyilatkozatot.

Latviski Līdz ar šo AsusTek Inc. paziņo, ka šī ierīce atbilst būtiskajām prasībām un citiem saistošajiem nosacījumiem, kas norādīti CE direktīvā. Lai uzzinātu vairāk, skatiet CE Atbilstības deklarāciju.

Lietuvių Šiuo dokumentu bendrovė „AsusTek Inc.“ pareiškia, kad šis įrenginys atitinka pagrindinius CE direktyvų reikalavimus ir kitas susijusias nuostatas. Daugiau informacijos rasite CE atitikties deklaracijoje.

Norsk AsusTek Inc. erklærer herved at denne enheten er i samsvar med hovedsaklige krav og andre relevante forskrifter i CE-direktiver. Du finner mer informasjon i CE-samsvarserklæringen.

Polski Niniejszym AsusTek Inc. deklaruje, że to urządzenie jest zgodne z istotnymi wymaganiami oraz innymi powiązanymi zaleceniami Dyrektyw

CE. W celu uzyskania szczegółów, sprawdź Deklarację zgodności CE.

Português A AsusTek Inc. declara que este dispositivo está em conformidade com os requisitos essenciais e outras disposições relevantes das Diretivas da CE. Para mais detalhes, consulte a Declaração de

Conformidade CE.

Română Prin prezenta, AsusTek Inc. declară faptul că acest dispozitiv respectă cerinţele esenţiale şi alte prevederi relevante ale directivelor CE.

Pentru mai multe detalii, consultaţi declaraţia de conformitate CE.

Srpski AsusTek Inc. ovim izjavljuje da je ovaj uređaj u saglasnosti sa ključnim zahtevima i drugim relevantnim odredbama CE Direktiva. Molimo vas, pogledajte CE Deklaraciju o usklađenosti za više detalja.

Slovensky Spoločnosť AsusTek Inc. týmto prehlasuje, že toto zariadenie vyhovuje príslušným požiadavkám a ďalším súvisiacim ustanoveniam smerníc ES. Viac podrobností si pozrite v prehlásení o zhode ES.

Slovenščina AsusTek Inc. tukaj izjavlja, da je ta naprava skladna s temeljnimi zahtevami in drugimi relevantnimi določili direktiv CE. Za več informacij glejte Izjavo CE o skladnosti.

Español Por la presente, AsusTek Inc. declara que este dispositivo cumple los requisitos básicos y otras disposiciones relevantes de las directivas de la CE. Consulte la Declaración de conformidad de la CE para obtener más detalles.

Svenska AsusTek Inc. förklarar härmed att denna enhet är i

överensstämmelse med de grundläggande kraven och andra relevanta bestämmelser i CE-direktiven. Se CE-försäkran om överensstämmelse för mer information.

Українська AsusTek Inc. заявляє, що цей пристрій відповідає основним вимогам відповідних Директив ЄС. Будь ласка, див. більше подробиць у

Декларації відповідності нормам ЄС.

Türkçe AsusTek Inc., bu aygıtın temel gereksinimlerle ve CE Yönergelerinin diğer ilgili koşullarıyla uyumlu olduğunu beyan eder. Daha fazla ayrıntı için lütfen CE Uygunluk Beyanına bakın.

Bosanski AsusTek Inc. ovim potvrđuje da je ovaj uređaj usklađen s osnovnim zahtjevima i drugim relevantnim propisima Direktiva EK. Za više informacija molimo pogledajte Deklaraciju o usklađenosti EK.

Appendices A-4

ASUS contact information

ASUSTeK COMPUTER INC.

Address

Telephone

Fax

Web site

4F, No. 150, Li-Te Rd., Peitou, Taipei 112, Taiwan

+886-2-2894-3447

+886-2-2890-7798 www.asus.com/

Technical Support

Telephone

Fax

Online support

+86-21-38429911

+86-21-5866-8722, ext. 9101# http://qr.asus.com/techserv

ASUS COMPUTER INTERNATIONAL (America)

Address

Telephone

Fax

Web site

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777

+1-510-608-4555 http://www.asus.com/us/

Technical Support

Support fax

Telephone

Online support

+1-812-284-0883

+1-812-282-2787 http://qr.asus.com/techserv

ASUS COMPUTER GmbH (Germany and Austria)

Address

Fax

Web site

Online contact

Harkort Str. 21-23, D-40880 Ratingen, Germany

+49-2102-959931 http://www.asus.com/de http://eu-rma.asus.com/sales

Technical Support

Telephone

Support Fax

Online support

+49-2102-5789555

+49-2102-959911 http://qr.asus.com/techserv

A-5 ASUS EX-B85M-V

We

Appendices A-6

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals