EOS 34.G Series Assembly And Operating Instructions Manual

Add to My manuals
12 Pages

advertisement

EOS 34.G Series Assembly And Operating Instructions Manual | Manualzz

34.G

GB

Assembly and operating instruction

MADE IN GERMANY

IPx4

D

Druck Nr. 29340727en /20.10

1

English

Table of Contents

Intended use ...........................................................................................................3

General notes .........................................................................................................3

Important notes .......................................................................................................4

Electrical connection ..............................................................................................5

Installation ...............................................................................................................6

Minimum clearances .........................................................................................6

Terminal connection diagrams ................................................................................7

Wiring diagram for 12-27 kW sauna stove with load distribution to control unit and power control unit .......................................................................................8

Wiring diagram for sauna heaters to 36 kW without load distribution .....................8

Sauna stones ..........................................................................................................9

Maintenance and care ............................................................................................9

Service Address: ...................................................................................................11

Guarantee .............................................................................................................11

Handling procedures for return shipments (RMA) - Details for all returns ! ..........12

2 GB

Dear Customer,

You have purchased a high quality technical system which will provide you with many years of enjoyable sauna bathing. This sauna heating system was constructed in accordance with state-of-the-art European safety standards, inspected and manufactured in accordance with the Quality Standard DIN

EN ISO 9001:2000.

This detailed installation and user‘s guide was created for your information. Please note especially the important information and the data dealing with the electrical connection.

We wish you a richly invigorating and restorative sauna bathing experience.

First of all, check whether the sauna system has arrived at your site undamaged. Register transport damage claims immediately with the delivering transport company or please consult the supplier who provided the equipment to you.

Intended use

This sauna heater is exclusively designed for the heating of sauna cabins, in connection with an appropriate control unit.

Any use apart from the defi ned application shall be regarded as non-intended use. Adherence to the conventional operating, maintenance and servicing conditions is also part of the intended use.

The manufacturer cannot be made responsible for deviating alterations undertaken on the authority of the user and any consequential damage. The risk for such measures shall be borne solely by the person carrying out the alterations and causing the damage.

Sauna heaters, with the exception of those used for household purposes, must be equipped with a safety device vis-à-vis the cover per DIN EN 60335-2-53.

As suitable measure, and depending on the sauna heater, a rocker switch Type I or Type

II may be installed above the heater.

(The rocker switch is not included in the delivery scope of the sauna heater.)

GB

For installation and electrical connection of the rocker switch follow the installation instructions supplied with this part.

General notes

Please note that an optimal sauna climate can be reached only when the cabin, with its air intake and exhaust, the sauna heating unit and the control unit have been tuned for compatibility with one another.

Please note all data and information provided by your sauna supplier.

The sauna heating units warm your sauna cabin through means of heated convection currents. To this end, fresh air from the air intake vent is drawn in, rises upon warming

(convection) and is then circulated through the cabin. A part of the used air is pushed out through the exhaust vent in the cabin. This is the means by which the typical sauna climate develops, reaching characteristic temperatures of about 110° C directly under the ceiling of your sauna, which fall off to about 30-40°C in the fl oor area due to the temperature gradient in the sauna cabin. Therefore, it is not unusual when, for example, temperatures of

110°C prevail in the area of the temperature sensor over the oven, while the thermometer, which is installed 20-25 cm under the cabin ceiling on the sauna wall, registers only 85°

C. With a temperature setting at maximum, the mean bathing temperature lies between

80°C and 90°C in the area of the upper recliner bench.

Please note that the highest temperature values in the cabin always develop in the area above the sauna heating unit and that the temperature sensor and safety limiter must be installed in this area in accordance with the control unit installation guide.

At the initial heating, you may notice a slight odor arising from evaporation of substances from the manufacturing process. Air out your cabin after this cycle before you begin with the sauna bath

3

Important notes

If assembled incorrectly, the sys-

tem will present a fi re hazard.

Please read this installation guide thoroughly. It is especially important to consider applicable dimensions and observe the following instructions:

• This device has not been designed for being used by persons (including children) that are physically or mentally handicapped or have sensory disabilities. Moreover, it is not allowed to use this device without suffi cient experience and/or knowledge, unless these persons will be supervised by persons responsible for their security or in case they have been instructed how to use this device.

air intake and exhaust vents must not be closed. Please observe the information provided by your sauna cabin supplier.

• For the adjustment and control of the sauna heating unit, one of the control units mentioned later must be used. This con-

• trol unit must be attached to a suitable location on the outer wall of the cabin, the associated sensor housings in the interior of the sauna cabin in accordance with the installation guide which accompanies the control units.

Caution: Covering and improperly

fi lled stone receptacles present a fi re hazard.

• Make certain that no objects have

been placed on the sauna heating unit before each start-up.

• Children are to be supervised in order to make sure that they do not play with this device.

• The installation and connection of the

sauna heating unit, control unit and other electrical equipment must be accomplished only by an expert. In this regard it is especially important to meet the required safety precautions in accordance with VDE 0100 v. §49 DA/6 and VDE 0100 part 703/2006-2.

• Caution: High temperatures on the

heating unit during operation can cause burns on contact.

• The sauna heating unit is not intended for installation or placement in a niche under the bench or under a roof slope.

• Do not start up operation of the sauna heating unit with air intake vents closed.

• The sauna heating and control units may be installed only in sauna cabins made of suitable, low resin and untreated material

(for example: Nordic pine)

• The cabin lighting with corresponding mounting must be of a type that it is splashproof and able to withstand a surrounding temperature of 140° C. Therefore, only a VDE-certifi ed sauna lamp of 40 W maximum may be installed for use with the sauna oven.

• Only a sauna oven with the appropriate heating capacity may be installed in the sauna cabin (see Table 2).

• There should always be a provision for air intake and exhaust vents in every sauna cabin. The air intake vents must always be aligned behind the sauna heating unit, ca. 5 to 10 cm above the fl oor. Please use the minimum dimensions of the air intake and exhaust vents listed in Table 1.

• The exhaust vents must always be placed towards the sauna heating unit diagonally in the rear sauna wall, lower area. The

4 GB

• The sauna system (sauna heating

unit, control unit and lighting etc.) may be hard-wired to the power source only by a locally certifi ed electrician.

All connecting lines laid on the inside of the cabin must be made of silicone and be able to withstand a surrounding temperature of at least 170°C. If single-wired cables are used as connecting lines, they must be protected by fl exible metal tubing.

The minimum diameter of the connecting line and the suitable cabin size in proportion to the power supply capacity are listed

in the table.

• During the installation of the sauna heating unit, make certain that the vertical clearance between the upper edge of the sauna heating unit and the sauna ceiling is suffi cient . The horizontal (lateral) clearance between the sauna heating unit and the cabin wall is provided in the dimension diagram of the respective sauna heating unit. The required distance between the lower edge of the sauna heating unit and the fl oor is also provided by the dimension diagram. In case of fl oor-standing ovens, the distance is determined by the base.

• Fundamentally, it is important to make sure that the sauna heating unit is not placed on a fl oor that consists of an easily fl ammable material (wood, synthetic fl ooring or similar material). Ceramic tiles or similar materials are practical in the area of the sauna.

• Underfl oor heating in a sauna leads to increased surface temperature of the fl oor.

• The distance between the oven safety grid or recliner bench and other fl ammable materials and the sauna heating unit are provided in the dimensional data of the respective sauna heating unit. The safety grid height must be approximately equal to the frontal height of the sauna heating unit.

• By cleaning of parts with sharp edges

or corners the appropriate personal protection measures against potential injuries should be taken.

Electrical connection

Your electrician will be able to accomplish this work without further explanation in accordance with the provided wiring schematic and with the help of the circuit diagram mounted inside the respective control unit.

Be sure to note, however, that live wires should not be visibly laid onto the inner cabin walls due to safety considerations. For this reason, the wall element with the air intake vent is already equipped with cable conduits in most sauna cabins

Should there be no cable conduits in your cabin, drill an hole in the cabin wall immediately adjacent to the sauna heating unit where the cable projects from the sauna heating unit and pull the cable through this hole towards the exterior and then to the control unit. The cable as well as all other connecting lines (supply wire to the power source and to the cabin lighting) on the outside wall of the cabin should also be protected from damage, for ex. by installation in cable conduits or by covering with wooden skirting strips.

GB

Attention!

Dear customer, according to the valid regulations, the electrical connection of the sauna heater and the control box has to be carried out through the specialist of an authorized electric shop.

We would like to mention to the fact that in case of a warrenty claim, you are kindly requested to present a copy of the invoice of the executive electric shop.

5

Installation

The sauna heating unit is designed for operation with an input voltage of 400 V AC 3N through the sauna control unit.

G 15 = 15 kW

G 18 = 18 kW

G 21 = 21 kW width=75 cm

G 24 = 24 kW

G 27 = 27 kW

G 30 = 30 kW

G 36 = 36 kW width=100 cm

When used for commercial purposes, the sauna heater may only be used in combination with the rocker switch Type II Art. No. 94.4424.

Minimum clearances

The sauna cabin must have a minimum inside height of 2.10 m.

When installing the sauna heater, please ensure that the vertical height between the top surface of the sauna heater and the roof of the sauna is at least 130 cm, and that the horizontal separation between the heater and the cabin wall or other fl ammable materials is at least 10 cm.

The distance between the heater guard and/or bench and other fl ammable materials must be at least 10 cm. The height of the heater guard must be the same as the height of the front of the stove.

10 cm

100 cm

(75 cm)

10 cm 10 cm

43 cm

Capacity acc. DIN

Electrical.

Connection

Fuse control unit in A

Fuse LSG in A

Connecting cable main

Connecting

- control unit in mm² cable main

- LSG in mm²

Connecting cable control unit - heater in mm²

Connecting cable LSG

- heater in mm²

Connecting cable control unit - LSG in mm²

15 kW

18 kW

3 x 16 5 x 2,5

21 kW

24 KW

3N AC

50 Hz

400 V

3 x 16 3 x 35

5 x 2,5

5 x 6

27 kW

30 kW 3 x 50 5 x 10

3 x 1,5

36 kW 3 x 63 5 x 16

All cross sections of a line are minimum diameters in mm² (Copper line)

Capacity acc. DIN

15 kW

18 kW

21 kW

24 kW

27 kW

30 kW

36 kW

Installation dimensions

H/W/D cm

95 x 75 x 53

95 x 100 x 53

For cabin size

18 - 25 m³

24 - 30 m³

24 - 34 m³

35 - 40 m³

Minimum dimensions of air intake and exhaust vents

50 x 6 cm

50 x 6 cm

50 x 8 cm

50 x 8 cm

40 - 50 m³ 50 x 9 cm

50 - 65 m³ 50 x 10 cm

65 - 75 m³ 50 x 10 cm

Weight without stones without package

48 kg

49 kg

50 kg

61,5 kg

62,5 kg

63,5 kg

65,5 kg

Stone fi lling

30 kg

45 kg

5 x 1,5

5 x 1,5

5 x 6

2 St. 5 x 6

2 St. 5 x 6

4 x 1,5

Power switch gear (LSG) needed

For operation with control units

ECON 45L09

EMOTEC L09

LSG 18

ECON 45A1

ECON 45A2

ECON 45H2

EMOTEC DC 9000

EMOTEC DC 9000 DB/DL/DLF

EMOTEC HCS 9003

EMOTEC HCS 9003 DB/DL/DLF

EmoTouch II PB/AF/GF

LSG 36

6 GB

Terminal connection diagrams

15 kW

N N N W V U

5 x 1,5

2

N N N W V U

5 x 1,5

2 to control unit to LSG

18 kW

N N N W V U

5 x 1,5

2

N N N W V U

5 x 1,5

2 to control unit to LSG

21 kW

N N N W V U

5 x 1,5

2

N N N W V U

5 x 6

2 to control unit to LSG

24 kW

N N N W V U

5 x 1,5

2

N N N W V U

5 x 6 2 to control unit to LSG

27 kW

N N N W V U

5 x 1,5

2

N N N W V U

5 x 6

2 to control unit to LSG

30 kW

N N N W V U

5 x 6

2

N N N W V U

5 x 6

2 to LSG

36 kW

N N N W V U

5 x 6

2

N N N W V U

5 x 6

2 to LSG

GB

LSG = Power control unit

7

Wiring diagram for 12-27 kW sauna stove with load distribution to control unit and power control unit

Saunasteuergerät control unit ECON / EMOTEC

L1 L2 L3 N S1 U V W WB WM N

Sensor

15 - 27 kW

9 kW 6-18 kW

4 3 2 1 4 3 2 1

LSG 9 /18

U V W N S1 V N L1 L2 L3 N

400 V AC 3N

400 V AC 3N

Wiring diagram for sauna heaters to 36 kW without load distribution

30 - 36 kW

Saunasteuergerät control unit ECON / EMOTEC

L1 L2 L3 N S1 U V W WB WM N

Sensor

4 3 2 1 4 3 2 1

LSG 36

U V W N U1 V1 W1 N S1 U V N L1 L2 L3 N

230 V 50Hz 400 V AC 3N

8 GB

Sauna stones

The sauna stone is a natural product. Check the sauna stones at regular intervals. Strong infusion concentrates especially can weaken the sauna stones and cause them to disintegrate over time. Consult your sauna supplier if necessary.

Thoroughly clean the sauna stones provided under running water and then place them in the stone receptacle so that the convection air current can circulate easily between the stones (Illust. 9 + 10).

The number of stones is adequate to create a steam burst, vaporizing about 10 cl of water per m³ cabin volume. Always wait 10 minutes after infusion before repeating the infusion. Only then are the sauna stones suffi ciently hot.

Never add more infusion agents or volatile oils than instructed on the packaging. Never use alcohol or undiluted concentrates. Caution! Fire hazard!

Maintenance and care

All sauna heating units are made of lowcorrosion material. Still, to enjoy your sauna heating unit for a long time, you should maintain and care for the unit. To this end, always make sure that the vents and refl ection plating in the area of air intake are free of objects. These can easily become clogged with fuzz and dust when drawing in fresh air. This reduces the air convection in the sauna heating unit and can be a cause of unacceptable temperatures.

Clean or de-scale the units when needed.

Refer to your sauna supplier or directly to the manufacturing plant in case of defects or signs of wear and tear.

Only use original manufacturer‘s replacement parts, which can be obtained from your supplier or directly from the manufacturer.

If you do not use your sauna for a signifi cant period of time, always check before next use that cloths, cleansers or other objects have not been placed on the sauna heating unit or the vaporizer before turning them on.

Please be sure to note!

Do not stack the stones in layers; stack them loosely instead, leaving as many spaces as possible to allow the rising hot air to circulate.

Remove stones from the sauna heater only when they are cooled off.

GB 9

For the installation of sauna heaters, please pay attention to the DIN VDE 0100 part 703 !

This standard makes the following statement valid in your newest expenditure, since February 2006, paragraph 703.412.05; Quotation:

The additional must be planned for all electric circuits of the Sauna by one or more fault current protection device (RCDs) with a calculation difference stream not more largely than 30 mA, excluded of it is Saunaheating.

The EN 60335-1 DIN VDE 0700 part 1 of January 2001 states the following in paragraph 13; quote:

The leakage current may not exceed the following values during operation:

- for stationary heaters of protection class I 0,75 mA; or 0,75 mA each kW input of the appliance, depending on the higher value, at a maximum value of 5 mA.

If the appliance is equipped with a protective device for leakage current (ELCB), please pay attention to the fact that no other electrical units will be protected by this ELCB.

Under current manufacturing methods, it is not yet possible to produce tubular heating elements for sauna heaters which do not attract moisture on each end from the surrounding air. It is also possible that moisture from the surrounding air has been concentrated in the magnesium-oxide fi lling in the heating elements during transport or storage and is now causing the ELCB to be triggered.

In this case, the oven must be heated up under supervision of an expert, during which the PE conductor is not connected. After about 10 minutes, when moisture has evaporated from the heating elements , the oven must be reconnected to the PE conductor!

If the sauna heater is not in use for a signifi cant period of time, we recommend running it every 6 weeks, so as to avoid moisture concentrating in the heating elements.

Therefore, should the ELCB be triggered during start-up, the electrical installation must be checked.

Installation of the sauna heater and control unit may be undertaken only by an authorized electrician. Without documentation of such installation, a warranty is fundamentally invalid.

10 GB

Guarantee

The guarantee is taken over according to the legal regulations at present.

Please keep this address in a safe place together with the installation guide.

To help us answer your questions quickly and competently, please provide data printed on the ID plate, to include system type, article no. and serial no., in all inquiries.

Service Address:

EOS-WERKE GÜNTHER GmbH

Adolf-Weiß-Straße 43

35759 Driedorf-Mademühlen, Germany

Fon: +49 (0)2775 82-0

Fax: +49 (0)2775 82-431 [email protected]

www.eos-werke.de

Manufacturer’s warrenty

- The period of warrenty starts from the date of purchase and lasts up to 2 years for commercial use and 3 years for private use.

- Always include the completed warrenty certifi cate when returning equipment.

- The warrenty expires for appliances which have been modifi ed without manufacturer’s explicit agreement.

- Damages caused by incorrect operation or handling through non-authorized persons are not covered under the terms of warranty.

- In the event of a claim, please indicate the serial number as well as the article code number and type name with expressive description of the fault.

- This warrenty covers damaged parts but no defects due to wear and tear.

In case of complaint please return the equipment in its original packaging or other suitable packaging (caution: danger of transport damage) to our service department.

Always include the completed warrenty certifi cate when returning equipment.

Possible shipping costs arising from the transport to and from point of repair cannot be borne by us.

Outside of Germany please contact your specialist dealer in case of warranty claims.

Direct warranty processing with our service department is in this case not possible.

Equipment start-up date:

GB

Stamp and signature of the authorized electrician:

11

Handling procedures for return shipments (RMA) - Details for all returns !

Dear customer we hope that you will rejoice in the ordered articles. Just in case that you are not entirely contented as an exeption, please follow the procedures specified below.This enabling us to ensure a quick and smooth handling of the return shipment.

Please absolutely respect for all returns!

• Please add the available RMA-voucher always completely fi lled out together with an invoice copy to the return shipment! Do not stick it on the goods or on the packaging.

We do not accept the return shipment without these papers.

• Not prepaid parcels will be refused and returned to Sender! Please always ask for the

RMA-No . for the cheapest return.

• Please pay attention that the goods have to be sent back without visible marks of use in the original scope of delivery and in original packing.

• We recommend to use an additional solid and break-proof covering box which should be padded out with styrofoam, paper or similar. Transport damages as a result of faulty packing are for the sender‘s account.

Form of complaint:

1) Transport damage 2) Faulty goods

• Please check the content of your parcel immediately and advise the forwarding company of a claim (parcel service/ freight forwarder)

• Do not use damaged goods!

• If the transport box has been damaged, please use an additional covering box. Do not forget to add the acknowledgement of the damage of the forwarding company !

• The implied warrenty period is 2 years.Please contact your dealer in case of faulty or wrong articles or missing accessories. He will discuss with you the individual case and try for immediate and customer-friendly solution.

• Ask the forwarder for a written acknowledgement of the damages.

• Report the claim promptly by phone to your dealer. He will discuss with you how to act in this case.

• For economic returns within Germany you will get an RMA-number from the manufacturer.

• All returns have to be in the original packing of the goods with corresponding accessories.

Please repack the goods to avoid damages. In case of wrong delivery, please do not use this article !

.

3) Problems of installation and functioning

• Please read the manual carefully fi rst of all and pay attention to the indicated assembly or installing instructions.

• Your dealer should be the fi rst contact person because he knows his products best and also knows possible problems.

• In case of function problems with an article, please check at fi rst whether there is an obvious material defect. The quality system in our factory reduces malfunctions of new appliances to almost zero.

12 GB

advertisement

Related manuals