WebGate MH1600H Installation & User Manual

Add to my manuals
119 Pages

advertisement

WebGate MH1600H Installation & User Manual | Manualzz

Installaction & User Manual

MH1600H

Digital Video Recorder

Installation/User Manual

We sincerely appreciate purchasing Digital Video Recorder.

For product connection and initial configuration, please, refer to the installation guide and for the product details, refer to user guide

0

English

Installaction & User Manual

Introduction

Thank you for purchasing a Webgate digital video recorder.

This manual is for MH1600H. Before product installation and operation, please become thoroughly familiar with this user manual and other manuals referenced by this manual.

This user manual and the software and hardware described here are protected by copyright law.

With the exception of copying for general use within fair use, copying and reprinting the user manual, either partially or in entirety, or translating it into another language without the consent of Webgate Inc. is strictly prohibited.

This specification may change without prior notice for improvement of product performance.

Product Warranty and Limits of Responsibility

The manufacturer does not assume any responsibility concerning the sale of this product and does not delegate any right to any third party to take any responsibility on its behalf. The product warranty does not cover cases of accidents, negligence, alteration, misuse or abuse.

No warranty is offered for any attachments or parts not supplied by the manufacturer.

 Malfunctions due to negligence by the user

 Deliberate disassembly and replacement by the user

 Connection of a power source other than a properly rated power source

 Malfunctions caused by natural disasters (fire, flood, tidal wave, etc.)

 Replacement of expendable parts (HDD, FAN, etc.)

※ The warranty period for the HDD and Fan is one year after purchase.

This product is not for exclusive use of crime prevention but for assistance in cases as fire or theft. We take no responsibility for damage from any incident.

1

Installaction & User Manual

Caution

As this equipment undergone EMC registration and suitable for business purpose, distributors and users are aware of this point.

FCC Compliance Statement

Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications, Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures

Warning

1. Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries

According to the Instructions

2. In case of changing built-in lithum battery, it should be replaced as same or kindred one to prevent a danger of explosion. Since old batteries could be a factor of environment contamination, be cautios to treat them.

3. Do not throw the batteries to fire or heating. Neither short circuiut or disassembly is prohibited.

4. Do not charge the batteries provided with Remote Controller

2

Installaction & User Manual

Important Notice

1. Do not place heavy objects on the top of the product.

2. This equipment is indoor use and all the communication wiring are limited to inside of the building

3. Product is for indoor use. It is not weatherproof. Use product with referring to its environmental specifications (Temperature & Humidity). To clean the product, gently wipe the outside with a clean dry cloth.

4. Product uses AC power of 110V ~ 240V. Be cautious not to cause electric damages to product.

5. Be careful not to drop the product. Physical shocks may harm the product including internal

HDD. In addition, be sure the product is secured after installation.

6. Product is made of metal. Therefore you can hurt human beings if you throw it to them or hit on them. When installing product, be cautious to locate on safe places where children are unreachable.

7. If Product does not operate properly, please contact the closest WEBGATE distributor for after sales service. Tampering or disassembling the product will void the warranty.

8. Security surveillance laws may differ for each country. Therefore, please contact the local region first to avoid any surveillance law violations.

9. "Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.

Therefore, consideration should be given to installing the equipment in an environment

3

Installaction & User Manual compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.

Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips)."

Experience and technical skills are needed for the installation of this product as an improper installation may cause fire, electric shocks, or defects. Any installation job should be performed by the vendor you purchased this product from.

The content of this manual can differ according to firmware or Software upgrading, and the standard and appearance of products may be changed for the improvement of quality without an advance notice.

4

Contents

Installaction & User Manual

INTRODUCTION ............................................................................... 1

KEY FEATURES .............................................................................. 10

INSTALL MANUAL.......................................................................... 13

1.

FEATURE ................................................................................. 13

1.1

Supplied Accessories .................................................................................................... 13

1.2

Description & Function .................................................................................................. 14

1.2.1

Front ...................................................................................................................... 14

1.2.2

Rear ...................................................................................................................... 16

1.2.3

REMOTE CONTROLLER ...................................................................................... 17

2. INSTALLATION ........................................................................... 19

2.1

Installation and Connection ........................................................................................... 19

2.1.1

Connecting & Running ........................................................................................... 19

2.2

Running OSD menu...................................................................................................... 20

2.2.1

OSD menu configuration ........................................................................................ 20

2.2.2

Setting remote controller ........................................................................................ 22

2.2.3

Installation examples ............................................................................................. 23

2.2.4

Basic Setting ......................................................................................................... 24

2.3

Connecting and configuring DIO ports ........................................................................... 28

2.3.4

HDD ...................................................................................................................... 39

2.3.5

Remote monitor and control ................................................................................... 40

2.3.6

External device connection .................................................................................... 41

2.3.7

NVS04 connection ................................................................................................. 42

USER MANUAL .............................................................................. 45

3.

MENU USE .............................................................................. 45

5

Installaction & User Manual

3.1

Menu Structure ............................................................................................................. 45

3.2

Function Menu .............................................................................................................. 45

3.3

Factory Reset ............................................................................................................... 46

4.

MONITORING .......................................................................... 51

4.1

Basic Screen ................................................................................................................ 51

4.2

Single Fll Screen Mode ................................................................................................. 51

4.3

Multi Screen Mode ........................................................................................................ 51

4.4

Screen Description ....................................................................................................... 51

4.5

Auto Switch Mode ......................................................................................................... 52

4.5.1

System Standard Mode .......................................................................................... 52

4.5.2

User Sequence Mode ............................................................................................ 52

4.6

Event Screen ................................................................................................................ 53

4.7

Zoom Screen Mode ...................................................................................................... 54

4.8

Pause Live Screen ....................................................................................................... 54

4.9

PTZ Control .................................................................................................................. 55

4.9.1 Pan/Tilt ....................................................................................................................... 56

4.9.2 Zoom/Focus................................................................................................................ 56

4.9.3 Load Preset ................................................................................................................ 56

4.9.4 Save Preset ................................................................................................................ 56

4.9.5 Auxiliary On ................................................................................................................ 56

4.9.6 Auxiliary Off ................................................................................................................ 57

4.9.7 Menu .......................................................................................................................... 57

5.PLAYBACK .................................................................................. 58

5.1

Playback Mode ............................................................................................................. 58

5.1.1

Playback on Standard monitor (16 / 9 division) ....................................................... 58

5.1.2

Playback function .................................................................................................. 58

6

Installaction & User Manual

5.2

SEARCH MODE ........................................................................................................... 58

5.2.1

Time Search .......................................................................................................... 59

5.2.2

Schedule Search ................................................................................................... 59

5.2.3

Event Search ......................................................................................................... 60

5.2.4

Thumbnail Search.................................................................................................. 60

5.3

Copy............................................................................................................................. 61

5.3.1

CD/DVD ................................................................................................................ 61

5.3.2

RE4 ....................................................................................................................... 63

5.3.3

AVI ........................................................................................................................ 63

6.CONFIGURATION ........................................................................ 65

6.1

Recording Structure ...................................................................................................... 65

6.2

System Setup ............................................................................................................... 65

6.2.1

Date/Time .............................................................................................................. 65

6.2.2

Disk ....................................................................................................................... 68

6.2.3

User Setup ............................................................................................................ 70

6.2.4

Utility ..................................................................................................................... 72

6.3

Network ........................................................................................................................ 75

6.3.2

xDSL ..................................................................................................................... 77

6.3.3

WRS ...................................................................................................................... 77

6.4

Device Setup ................................................................................................................ 78

6.4.2

Camera Setup ....................................................................................................... 78

6.4.3

Monitor Setup ........................................................................................................ 79

6.4.4

Audio Setup ........................................................................................................... 81

6.4.5

Text Setup ............................................................................................................. 82

6.4.6

Serial Setup ........................................................................................................... 83

6.5

Event Setup .................................................................................................................. 84

6.5.2

Event Check .......................................................................................................... 85

6.5.3

Sync Event ............................................................................................................ 86

6.5.4

Motion Detection .................................................................................................... 87

6.5.5

Sensor ................................................................................................................... 89

6.5.6

Preset .................................................................................................................... 89

7

Installaction & User Manual

6.6

Recording setup ........................................................................................................... 90

6.6.2

Program setup ....................................................................................................... 90

6.6.3

Manual/Schedule recording setup .......................................................................... 91

7. WEB VIEWER ............................................................................. 97

7.1

System requirement...................................................................................................... 97

7.2

Login ............................................................................................................................ 97

7.3

User Setup ................................................................................................................... 98

7.4

Browser available ......................................................................................................... 99

7.5

Monitor ......................................................................................................................... 99

7.5.1

Screen division and changing video position .......................................................... 99

7.5.2

Move to Playback ................................................................................................ 100

7.5.3

Channel On/Off .................................................................................................... 101

7.5.4

Sensor Indication ................................................................................................. 101

7.5.5

Relay operation ................................................................................................... 101

7.5.6

Using Microphone ................................................................................................ 101

7.5.7

Event Data........................................................................................................... 102

7.5.8

Video Recording & Save Saving .......................................................................... 102

7.5.9

Using PTZ ........................................................................................................... 103

7.5.10

Using Audio ......................................................................................................... 104

7.5.11

Closing Video Channel ........................................................................................ 104

7.6

Playback..................................................................................................................... 105

7.6.1

Video Division & Changing Channel ..................................................................... 105

7.6.2

Image recording ................................................................................................... 105

7.6.3

Print..................................................................................................................... 106

7.6.4

Backup ................................................................................................................ 106

7.6.5

Web Monitor ........................................................................................................ 107

7.6.6

Channel On/Off .................................................................................................... 107

7.6.7

Saving time & Checking Rec, Capacity ................................................................ 107

7.6.8

Searching Calander ............................................................................................. 107

7.6.9

Functional function at the buttom of monitor ......................................................... 108

8.

USER MANUAL FOR MOBILE VIEWER ............................. 109

8

Installaction & User Manual

8.1

Log-In page ................................................................................................................ 109

8.2

Monitoring page .......................................................................................................... 109

TROUBLE SHOOTING .................................................................. 111

THE WAY TO CHECK THE MANUFACTURING DATE ............... 113

AVAILABLE HDD .......................................................................... 114

COMPATITABLE CD/DVD LIST ................................................... 114

SPECIFICATION............................................................................ 114

PRODUCT DIMENTION ................................................................ 117

9

Installaction & User Manual

KEY FEATURES

Monitoring Screen

Supprots real live video with high resolution per each channel and variable display mode.

 Real H.264 Video

 Various monitoring

Single, 4ch, 9ch, 10ch, 16ch

 Auto Switching(AUTO)

Composite 4 ea, DVI 2ea

Audio Recording

Supprots real-time audio input and recording

 Simultaneous 16ch audio input & recording available

 Input : 4ch RCA, 12ch D-SUB, Output : 1ch(Rear)

 Simultaneous audio recording and playback available

Recording

It supports 480ips recording at H.264 High-Resolution (4CIF) and available to record max.

5 seconds before triggering an event. Also, convert function is available protecing privacy(Covert func.).

 H.264 Video recording with High-Quality

D1(720x480) 480ips

 Supports manual & schedule recording

 Video loss detection

 Supports archiving event list (Sensor, Video loss, Motion detection, Text)

Available record Max 5 seconds before triggering an event per each channel

10

Installaction & User Manual

Search / Playback

It supports variable and convenient functions for search & playback.

 Play back by time,date,channel

 Easy and convenient search using mouse

 Pre/Post search from a freeze frame

 Play back by Event (Sensor, Video Loss, Motion Detection, Text)

 Easy search by Remote controller

Back up device

It is available to back up to DVD-R,CD-R,USB memory by user’s choice

 Supports various back up device : DVD-R, CD-R, USB, 1394b

 HDD external unit (recordin unit for external capacity expension)

Network

It supports variable network like LAN, XDSL and easily control from remote site using PC cliet viewer.

 E-mail notification thru, TCP/IP, DHCP in case of triggering an event

 Live monitoring form remote site (Whole screen or available to select quad screen)

 Available to playback, recording, search and DVR management thru. network viewer in PC

 Available to record, search & playback by time from remote site.

 Supprots 10/100Mbps Ethernet/xDSL

 Multiple DVR connection

ETC

 Supports User friendly GUI and mouse function

11

Installaction & User Manual

 Supports User friendly GUI and mouse function

 Easy and simple firmware upgrade thru. USB memory

 PTZ Control (SPEED DOME), PRESET fucntion

 Available to control up to 16 DVRs with one remote controller

12

Installaction & User Manual

Install Manual

1. Feature

1.1 Supplied Accessories

Unpack and check all the items as below

AC Cord, Remocon, Setup CD, HDD Fixing Clamp, SATA Cable, HDD Fixing Screw, Rack

Mount

13

Installaction & User Manual

1.2 Description & Function

1.2.1 Front

1

구분

DVD-Multi for

Back up

2 USB Port

Power LED

Network LED

3

Recording LED

Playback LED

4

Copy

Sequence

Multi

Select

Zoom

Ack

Relay

Mon

Rec

5 Channel

6 Search

7 Menu

9

10

11

Exit

Power button

IR

기능

Back up use for recorded data by DVD/CD media

Use connecting USB memory or Mouse

Display Power status

Display network status

Display recording status.

Display playback status.

To run copy mode.

To run or stop user sequence.

To change DVISION in live or playback mode.

To run PTZ control panel

To run digital zoom in live screen upto x2.

Stop buzz of event action

To run and pause Relay action by manual.

Swiching monitor

To start and stop recording

To select the channel.

To enter Search mode.

To enter Menu

To enter Function mode.

To exit menu or close pop-up window.

Power on/off

Remote controller receiving sensor

14

12 Enter/Play

13 ◀ /REW

14 ▶ /FWD

15 ▲/Pause

16 ▼/Stop

Installaction & User Manual

To select menu or enter playback mode.

To move or select in menu and change replay speed to reverse direction in playback mode

To move or select in menu and change replay speed to forward direction in playback mode.

To move or select in menu and pause live/ replay video.

To stop replay in playback mode.

15

Installaction & User Manual

1.2.2 Rear

No Input/ Output name

1 Power connector

2 CH1~16

3 Loop out

4 Monitor 1~4

5 Audio input(RCA)

6 Audio output

7 Ground

8 Ethernet

9 Storage

10 eSATA port

11 DVI OUTPUT 1,2

12 Com1

13 Com2,3

14 Relay

15 Sensor IN

16 D-Sub Audio port

17 Fan

Descrtiption

Socket for AC100V~AC240V power cord.

BNC input for camera connection

BNC output(Loop) for camera connection.

BNC connection for monitor output.

RCA connection for Audio input

Speaker output terminal.

Ground between DVR & external device.

For network connection (RJ-45)

For external HDD connection

For eSATA external HDD connection

Vidoe output port to connect PC monitor.

RS-232C D-SUB.

For RS-485.

Relay Connection terminal.

Input for external sensor.

D-Sub port for Audio

Exhaust internal heat out

16

Installaction & User Manual

1.2.3 REMOTE CONTROLLER

It is available to use all functions of DVR. If several DVR are set with unique ID numbers, they can be controlled with one remote controller. To use remote controller, it is necessary to set ID first which want use. Keep pressing ID button repetedely (Up to Max. 16 times) and use it matching DVR & ID.

7

8

9

3

4

5

6

No.

1

2

Iten

ID

LOCK

COPY

BACKUP

RELAY ON

RELAY OFF

SEQ

MULTI

ZOOM

Description

To select Remote Controller ID

Not use

To indicate copy menu, copy recorded data to USB

Not use

To manually ON

To manually OFF

Auto sequencing

To change division

To run digital zoom

17

Installaction & User Manual

14

15

16

21

22

23

24

25

17

18

19

20

26

27

28

10

11

12

13

29

30

31

32

33

34

35

SEARCH

CHANNEL BUTTON

SELECT

+10

FN1

FN2

MENU

To indicate search menu

To select channel

Not use

In case of selecting over 10

(+10 + 1)

Not use

Not use

Covert to menu screen

HELP

◀ /REW

▶ /FWD

▲/PAUSE

Not use

Move setting menu to left direction/REW

Move setting menu to right direction/FWD

Move setting menu to top direction/PAUSE

ENTER/PLAY

ENTER

EXIT

FAST REWIND( ◀◀ )

REWIND PLAY( ◀ )

FORWARD PLAY( ▶ )

Move setting menu to bottom direction/STOP

Menu selection/Playback

To select menu

To cancel setting, escape from menu

Speedy replay to reverse direction

Replay to reverse direction

Repleay to forward direction

FAST FORWARD

( ▶▶ )

Speedy replay to forward direction

STOP( )

STEP REVERSE( ◀ l)

To stop replay

Replay to reverse direction by each frame

STEP FORWARD (l ▶ ) Replay to forward direction by each frame

PAUSE(ll)

P/T

LOAD PRESET

To freeze playback

PAN/TILT Control

To read preset

AUX ON Auxiliary ON

18

2. Installation

2.1 Installation and Connection

2.1.1 Connecting & Running

2.1.1.1 Connecting camera

Connect CCTV camera to DVR with BNC cable as below.

Installaction & User Manual

- The video type for all channels should be either NTSC or PAL, not be combined both

- DVR sets video signal’s impedance (75Ω) automatically. Impedence is set as 75 Ω basically. If connecting a dvice to video output, impedance will be “Hi-z” status.

- Video Type (NTSC/PAL) should be changed after booting DVR. The order of camera recognition follows ch1 through Ch16 camera amd 1 st

recognized camera type leads other camera type.

2.1.1.1 Connecting monitor

Connect CCTV monitor to DVR with BNC cable as below.

2.1.1.2 Connecting Audio

Connect audio signal to DVR with using RCA cable or D-SUB as below.

19

Installaction & User Manual

2.1.1.3 Supplying Power

Connect power cable as below.

- When supplying power, DVR starts booting automatically.

- In order to cut off power, press power switch on DVR front during 5 seconds, then select

“YES” after appearing a pop-up window.

- For supplying power again, push the Power button.

2.2 Running OSD menu

2.2.1 OSD menu configuration

Press [MENU] in keypad of front to open configuration menu as below

20

Installaction & User Manual

(1) Main Menu : The selected tab is show in bright color and the related sub-menu will be shown left- below the tab. To move to the previous/next tab, use the [ ◀ / ▶ ] arrow buttons. To move to a sub-menu press the [Enter] key.

(2) Sub-menu : The selected sub-menu is shown as tab title and the related setting will be shown. To move to the previous/next tab, use the [ ◀ / ▶ ▲/▼] arrow buttons. To move to the related setting press [Enter]. To move to upper main menu, press [ESC] button.

(3) Setting page : The selected tab is shown as orange, To move to the previous/next tab, use the [ ◀ / ▶ ] or [▲/▼] arrow button and press [Enter] key for value setting. Whn setting value is a word, a dialogue box to edit the word will be open. When setting value is number, it should be set with using [ ◀ / ▶ ] or [▲/▼]. Press [ESC] button when the value is set and also [ESC] button is available to upper sub-menu..

2.2.1.1 Dialogue box to edit a word

Dialogue box to edit a word is image shown as below; It is available to input both word and bumber.

Keep pressing [▲/▼], [ ◀ / ▶ ] arrow button until the word is looking for and press Enter. In case of deleting input word press [  ], spacing words press [  ] button. To exit from dialogue box, press [Enter] after finishing word input.

21

Installaction & User Manual

2.2.2

Setting remote controller

2.2.2.1 Setting ID of DVR

When controlling several DVRs with one remote controller, set Remote Control ID as follws.

(1) Press the [MENU] button

(2) [ ▶ ] Select “system” with using [ ▶ ] arrow button and press [Enter] or [▼] button

(3) [▼] Select “Utility” with using [ ▶ ] arrow button and press [Enter] button.

(4) Select “Remote Control ID” and press [Enter]

(5) [ ◀ / ▶ ] Select a value using [ ◀ / ▶ ] arrow buttons and press [ESC]

(6) Press the [ESC] button to return to the monitor mode.

<Reference>

Up to 16DVRs can be controlled with a single remote controller.

When not using remote controller, set the Remote Control ID as “Off”

2.2.2.2 Setting ID

If several DVRs are with unique ID numbers, they can be controllerd with one remote controller.

To select a specific DVR, keep pressing the ID button of remote controller until a buzzer sounds during 2 seconds.

22

2.2.2.3 Operable range of remote controller

Installaction & User Manual

2.2.2.4 Loading the batteris into the remote controller

Remote controller required two AAA-type batteries. Please, refer the following installation step.

1. Remove the batter cover.

2. Taking care the poles (+/-)

3. Replace the batter cover. are correctly positioned

2.2.3 Installation examples

2.2.3.1 Basic configuration

Connect camera and monitor and Audio.

2.2.3.2 Advanced configuration

Connect camera, monitor , audion, sensor, realy etc..

23

Installaction & User Manual

2.2.3.3 External storage & back up configuration

Use USB for back up.

2.2.3.4 Internet / Intranet configuration

2.2.4

Basic Setting

24

Installaction & User Manual

2.2.4.1 Viewing Image

When power is on, eDVR starts automatically and displayed in basic 16ch-split screen after booting.

<Reference>

If user password is set, a prompt for entering the password will be appeared. Factory default is reserved as not responding keypad on DVR front (It is not from factory default)

2.2.4.2 Setting Date & Time

- Press [MENU] button and select “ System” when OSD menu is appeared.

- Select“Date/Time”and press [Enter] button.

Time Zome

Use the left or right arrow key on the front or the mouse wheel to select your time zone. Each press of the arrow keys changes the time zone. (To go to the previous menu, press the [ESC] button on the front or right-click. This is the same for all OSD menus.)

25

Installaction & User Manual

Daylight saving

This menu is linked with “ time zone ” setting. For example, if the countries applied for daylight saving in time zone setting menu then daylight saving will be turn to ON and other counties are not applied for daylight saving then this option will be turn to OFF, and additionally the user can configure the daylight saving option manually for the counties that were not applied, and in this case, you can use “ Custom ” option to set.

The second is for selecting a month, week, and day to define the start and end times of DST.

NTP

(1) Select yes or no of using NTP.

(2) Select NTP mode among Client, server, Both using directional key. [ ◀ / ▶ ] or [▲/▼]

(3) Select Public or Both.

(4) Enter server IP address when configuring server type by Local.

(5) Configure communication interval with server.

DATE FORMAT

(1) Select “Date Format” using [ ◀ / ▶ ] or [▲/▼] arrow button and press [Enter] button. Select a value using [ ◀ / ▶ ] arrow button from YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY.

(2) Press [ESC] after finshing value setting.

TIME

(1) Select “Time” using [ ◀ / ▶ ] or [▲/▼] arrow button and press [Enter] button.

(2) Select Date, Time using [ ◀ / ▶ ] arrow button and set value using [▲/▼] arrow button.

(3) Press [ESC] after finshing value setting..

APPLY

26

Installaction & User Manual

Most setting values are appled automatically, when exiting form the related menu page. But

“Date” & “Time” setting are not applied automatically because they may critically affect the file system of the recorded HDD. To apply Date/ Time settings confirm with [Apply Date/Time] buttons.

(1) Select “Apply Date/ Time” using [ ◀ / ▶ ] or [▲/▼] arrow button and press [Enter]. Then, a warning message will be appeared as below image;

(2) Select using [ ◀ / ▶ ] or [▲/▼] arrow button and select “YES”, then, press [ENTER] button.

To cancel, press [ESC] button.

2.2.4.3 Record Setting

Select “Record” pressing menu button in front.

Program Setting

Set resolution, frame rate, quality by each channel that user want record in “Program” of record menu

27

Installaction & User Manual

Schedule Setting

Set recording mode as “Scheduel & Event” and set by date/ time.

Checking method for recording

<Reference>

If recodrding setting is finished correctly, “REC LED” in front is flickering. In addition, it is marked

[S] indicating that all channels are recroding .

2.3 Connecting and configuring DIO ports

2.3.1 Wire Handlin

When connecting a wire to a terminal block, follow the instruction below. Not the different types of wire that can be used.

28

Installaction & User Manual

- Standard wire : Pie off the wiring cover 8~10mm and solder it. Wire gage should AWG

22~26.

- Sold wire : Peel off the wiring cover 8~10mm and solder it.Wire gage should be AWG 20~26.

2.3.2 Inserting & removing wire

To insert & remove wire in Terminal Block, use a screw driver in the diagram like below.

2.3.3 Conneting and configuaring sensor

2.3.3.1 Specification

In order to run sensor input DVR normally, the following conditions are required.

Input Ch 16EA Transistor input

Spec

Input type N.C, N.O supprt

Supported sensor Dry contact sensor

Way of connecting Connecting the trimmed wire to terminal block

Available input

Performance pulse range

Output current

Minimum 500ms

Typical DC 12mA

29

Installaction & User Manual

Connecting sensor input

Connect S1 ~ S16 with referring the following image. It shows to connect a dry contact (Please refer “Wire Handling”.

Setting Sensor

(1) Press [Menu] button and select “Event” when OSD menu is appeared.

(2) Move to sub menu pressing [Enter] or using [▼] button and select [Enter].

All Sensor

It is used when setting for all sensors and set Off, or Normal Open (N.O.) / Normal Close

(N.C.) type.

(1) Select All and set type.

Each sensor

It is used when setting for each sensor and set selecting each sensor.

(1) Select sensor and press [Enter] button.

30

Installaction & User Manual

(2) Select sensor that user want set and set type.

(3) Press [ESC] after finishing value setting.

2.3.3.2 Connecting relay and stting

Specification

In order to run relay output of DVR normally, the following conditions are required.

Output Ch. 2EA relay outputs

SPEC Output type

Connecting type

Dry contact

Connect the trimmed wire to terminal block

Perfromance

DC

AC

30V 1A

125V 0.5A

Connecting relay out

Connect R1 ~ R4 with referring to the following images, it shows to connect a warning light.

Please refer the “Wire Handling”

Relay setting

It is available to run relay selecting from sensor, motion detection, Video Loss which is normal event source and Disk error, Disk full, authentication fail, WRS registration fail which is system event source. Also, user can set working condition by schedule. In case of using control center thru. network, realy could be run from remotely.

31

Installaction & User Manual

2.3.3.3 Connecting serial port

Configuring serial ports for Pan/Tilt/Zoom

If DVR supports thru. COM port, it is available to connect PTZ camera and control it. For a list of supported protocols, please refer to the list on the OSD configuration menu. The following figure shows how to connect PTZ camera to RS485 (COM2). When using another serial port, connect it with referring to each connection diagram below.

Please refer the “Wire Handling”.

Serial communication port diagram

32

Installaction & User Manual

COM2/COM3 diagram (RS-485)

COM1 diagram (RS-232)

Available PTZ is same as below table.

Model name

Keyboard KBD300A, WGI SPD1800/2600

WKC-100 keyboard

BOSCH AutoDome, TC8560X-4

PELCO(P), PELCO(D)

Honeywell 755/655, HRX-2000, ScanDome2

Sony EVI-D3x

VT VPT-4x

SDZ160/330, Samsung SPD,

Keyboard SCC3000, Samsung SRX-100B

AD SpeedDome

SungJin SJ372R1’

33

Webgate

Webgate

Bosch

Pelco

Honeywell

Sony

VT

Manufacturer

Samsung Techwin

AD

Sungjin

Installaction & User Manual

Samsung SCC641

Panasonic WV-CS850

LG GAC-PT2

Keyboard KBD300A, WGI SPD1800/2600

Merit-Lilin FastDome

Elmo PTC200C

Canon VC-C4

HTC-230S

RVision

Elbex

VIDO

VICON

Hunt

ORX-1000

Fine CRR-1600

Tokina

Kodicom KRE

Nuvico

Samsung Electric

Panasonic

LG

Honeywell

Merit

Elmo

Canon

Dongyang Unitech

RVT

Elbex

VIDO

Vicon

Hunt

Sysmenia

LiveEye

Tokina

Kodicom

Nuvico

Serial Setting

You can set up both serial port and PTZ from remote menu under network menu.

From serial setting, you can set protocol, port, baudrate, parity bit, stopbit and databit.

After completed serial setting, select desired channel from camera menu, and setting up PTZ

Home, PTZ Idle Time, PTZ Port, and PTZ address.

34

Installaction & User Manual

2.3.3.4 Connection to external device via Serial port

Text input device connection (ATM / POS / Access Control)

Using COM1/RS232, TEXT DATA can be recorded with synchronizing POS/ATM..

Like above picture, connect COM1/RS232 (9pin D-Sub) in Device menu and configure Serial and Text

Serial (COM1) Setup

(1) OSD Select “Device” in OSD menu and move to sub menu.

(2) Seleting COM1 and configure “Text”in Device

(3) Setup the value of Baud Rate/Parity/Stop bit/Data bit with the device.

35

Installaction & User Manual

Text Setup

(1) Select “Deice” on OSD, and move to sub menu.

(2) Select “Text”and configure relevant text information.

<Reference>

Since external device can not be recognized, before installing, please, ask to the shop.

2.3.3.5 USB Device Connection

USB port is for the simple video copy (within 1 hour) on USB Flash memory. Its recommended specification is same as below.

USB Spec.

Device

Voltage/electric current

Ver 2.0

USB Memory Stick,

Max. 200mA per DC 5V / Port

<Reference>

It should be formatted by FAT32.

In case of normal connection, if executing Copy menu, disk will be recognized same as below and Set copy range  Select Drive  Execute Copy

36

Installaction & User Manual

[CD/DVD Copy]

Select the channel to copy.

[RE4 Copy]

37

Installaction & User Manual

[AVI Copy]

<Reference>

A USB Flash memory which should install additional program on Windows OS, can not be recognized.

2.3.3.6 Video In/Out connection

3 Video Input/Output is Loop through and check the connectivity automatically and set end resistance.

4 For instance, if connected by Video input, end resistance is configured by75Ω and if

5 Video in/output is same, it will be Hi-z mode. Therefore, in case that Input/Outut are connected at the same time, end resistance of device receving output should be configured by 75Ω.

2.3.3.7 Audio In/Out connection

There are 4 RCA Auido Input and and 12 D-sub Audio input and 1 RCA output.

38

Installaction & User Manual

2.3.4 HDD

※ Please, refer to Appendix for available HDD list.

2.3.4.1 HDD registration and format

After mounting HDD and booting system, “Disk Manager” will execute automatically.

If not, please, check the connectivity of HDD

(1) Press [Enter] button in “Disk Manager”

(2) Using [▲/▼] Key, select new HDD(Displayed [No] on Enabled item) and press [Enter].

(3) If you see the message for format, select [Yes].

(4) Press [ESC] and escape from “Disk Manager.

2.3.4.2 HDD Replacement

(1) Turn Off the DVR and take off the HDD that has a problem and replace it with new

HDD.

(2) Turn On the DVR and go to “Disk Manager” menu and select the previous HDD which has a problem, and press “Enter” Key.

39

Installaction & User Manual

(3) “ Removed disk will be Confirmed” message will be pop-up and select “Yes” to delete it from the list.

(4) Select the new HDD from the list and press “Enter” key.

(5) Select “Yes” when the system asking “do you want to format”

(6) After complete above procedure then Press “ESC” key to exit the “Disk Manager” menu.

<Note>

1 . HDD Re-using (Add Used)

You can use HDD that has been used before from DVR, in this case you do not need to do format and delete the data.

How to use it? Please install previous HDD in the DVR, and go to “Disk Manager” menu and select the HDD that you wish to re-use which is you just installed HDD, and press “Enter” key then you will see the pop-up message “This disk can be added without format/Nevertheless, do you want format this disk?” and select “NO” for re-use without format, and select “YES” for format.

2.3.5

Remote monitor and control

Via Internet/Intranet, in remote site, user can access with PC.

2.3.5.1 Ethernet connection

(1) Cut power

(2) Connet Ethernet cable to DVR and Hub.

(3) Input Power..

<Reference>

40

Installaction & User Manual

To protect DVR demage, after connecting Ethernet cable, input Power.

Please, check Ethernet cable connection firmly.

Input power on DVR and check their connectivity.

2.3.5.2 Network configuration

Ethernet

Set type as Ethernet and input IP, Netmask,Gateway, DNS.

The way to input is using directional key or mouse wheel.

PPPoE

Set type xDSL, and move to xDSL menu.

First, change Ethernet Port

Please, input ID and Password for PPPoE.

WRS

After changing interval over 1 min, register WRS address and product and input Group ID.

2.3.6 External device connection

DVR has external Storage Device Interface and 1 ea of eSATA port. Using eSATA port, user can expand Storage capacity up to 8TB.

<Note>

Since some of eSATA device can not be compatible with DVR, before the usage, please, contact the seller and check its compatibility in advance.

41

Installaction & User Manual

2.3.6.1 eSATA Device Connection

In case of external eSATA supporting FireWire, using eSATA port on the rear part. And since

DVR does not support power to eSATA, eSATA device should be one external power is supported.

<Note>

Basically eSATA is connected to DVR while DVR is running, works properly. However it depends on eSATA manufacturer. Therefore, we recommend below order for making connection.

1. Power on DVR.Connect external HDD to IEEE1394 port.

2. Power on external device

3. Power on eDVR

2.3.7 NVS04 connection

2.3.7.1 Connecting with DVR

(1) Connect to DVR as shown in the picture below using Gigabit Ehternet Cable.

(2) Connect DVR Port of NVS04R and Storage Port of DVR directly..

42

Installaction & User Manual

<Note>

1) The network cable connected to DVR should be Gigabit Ehternet Cable (Category-6). If not, it is not connected to DVR.

2.3.7.2 Set ID Configuration

Set ID using Rotary Switch located on the back. This ID is used as IP Address of NVS04R and the form of IP address is 10.10.20.XXX. when the user connect more than 2 units of NVS04R, each ID should be set differently.

Set the ID using driver. The value for the first digit of switch should match with valus of 100x on the rare panel while the second digit of switch should match with value of 10x and the third digit of switch should match with 1x on the rare panel

43

Installaction & User Manual

2.3.7.3 Power connection and operation

(1) Connect power as below.

(2) As soon as power is connected, the device starts booting.

<Note>

1) It takes around 1 minute to connect NVS04R and DVR after connecting power.

Four LEDs at the front starts blinking and they are fully on when connection is completed. The

HDD list is available to check at Disk Manager

2) Refer the manual of “ NVS04R installation and user guide ” for detailed explanation..

44

Installaction & User Manual

User Manual

3. Menu Use

3.1 Menu Structure

The menu structure will be shown like below image, and each menu setting method descriped from chapter 4 to chapter 6.

3.2 Function Menu

To run Fucntion menu, please, click the right button of mouse or push “Help” button on the front panel.

The Function menu can be controlled by mouse.

Each function can be executed by clicking right button of mouse and click desired icon.

The Function menu also can be controlled by front part of DVR’s buttons.

Please refer to below picture for the Function menu structure.

45

Installaction & User Manual

3.3 Factory Reset

In order to reset value to factory value, go to System Setting->System->Setting, and once press

Factory Reset then the warning message will be appear, click “Yes” to reset the DVR value to factory.

Default Value from Factory

System

Time Zone

Daylight Saving

UTC 00:00 Dublin

Off

Date

Time

/

NTP Function

Holiday Select

Date Format

Sync With

NTP

Korean

Off

NTP Mode Client

NTP Server Public

Loc.

NTP Local 0.0.0.0

Server IP

Interval 1(hour)

UTC 00:00 Dublin

No

46

Disk

User

Setup

Utility

Network

Network xDSL

WRS

Type

DHCP

IP addr

Net Mask

Gateway

DNS1

Additional DNS

Port

Band Width

Limit(Mbps)

User ID

Password

Status

Interval

URL

Group

Status

Time

Over Write(Auto

Deletion)

Block Playback

Disk Full Alarm

Warning

Disk Manager

Disk Status

DVR Alias

DVR Keyboard ID

Remote Controller

ID

Language

Firmware Update

System Log

Factory Reset

47

Installaction & User Manual

DVR0

1

All

English

>>

>>

>>

MM/DD/YYYY

On

Off

50 o

C

>>

>>

No Password used

Ethernet

Off

Default IP

Default Net Mask

Default Gateway

0.0.0.0

>>

80

0.0

Guest

***** xDSL not connected

Off www.honeywell.co.kr/security/english

Newbie

Not Registerd

Installaction & User Manual

Device

Camera

Monitor

Audio

Text

Camera Number

Name

Status

Type

Color

AGC

Bright

Contrast

Ch1

Cam 1

On

NTSC

Color

Enable

0

0

PTZ

Monitor

Alarm Pop-up(Sec)

PTZ Home

PTZ Idle

Off

5

Time

PTZ Port None

PTZ Address 0

Off

<< User Sequence

Configuration

SEQ Time(Sec)

Covert

Multi Moce

VGA Moce

Infor Level

Audio Channel

5

>>

4E, >>

800x600@56Hz

Audio Recording

Audio Gain

Sync Video Channel

>>

Audio Mix

Recording

Sync Test With

Device

Seek Header

Header 1

Header 2

Delimiter

Timeout(ms)

Off

Ch1

Manual

Off

Header1

Header2

0D0A

1000

48

Installaction & User Manual

Serial

Lines

Serial Port

Device

Interface

Baud Rate

Parity Bit

Stop Bit

Data Bit

20

Com1

Non

RS232

9600

None

1

8

Event

Event

Motion

Sensor

Preset

Record

Event Check

Event Action

Action Duration

Normal

Source

Event

Event System

Source

MD

Sensivity

Area

Sensor

Channel Mumber

Preset

Record

Record Mode

Program

Event Duration

Playback

Deinterlace

Normal

Program

Event

Always

Relay1

10 Sec

>>

>>

All

2

Set All

All, N.O.

Ch1

Sensor1, Preset1

Manual & Event

ProgramK

>>

On

Resolution All D1

Frame Rate All 6

Quality All Q5

Resolution All D1

Frame Rate All 6

Quality All Q5

Factory Default value

49

Installaction & User Manual

MH1600H

Rec mode

List

A

B

C

D

E

F

G

H

I

Res

D1

D1

D1

Half

Half

Half

CIF

CIF

CIF

Normal

Fps

30

15

7

30

15

7

30

15

7

Q5

Q5

Q5

Q5

Q5

Q5

Q

Q5

Q5

Q5

Res

D1

D1

D1

Half

Half

Half

CIF

CIF

CIF

Event

Fps

30

15

7

30

15

7

30

15

7

Q5

Q5

Q5

Q5

Q5

Q5

Q

Q5

Q5

Q5

50

Installaction & User Manual

4. Monitoring

All analog video image channels connected to DVR is displayed to screen by Power connection.

It is to utilize all monitoring mode of DVR.

4.1 Basic Screen

After Power connection, the DVR operates on automately.

It boots with LED on.

After booting, 16 channel screens are displayed.

※ If there is user password set, Password input window will be displayed

4.2 Single Fll Screen Mode

Press the channel number wanted or click mouse button.

Press [MULTI] button to return to divisional screen

4.3 Multi Screen Mode

Press [MULTI] for multi channel display or click

“Display” icon from Function menu.

Press [MULTI] button every time, screen mode is changed to 1~4, 5~8, 9~12, 13~16, 4C, 1~9,

8~16, 1~10, 16 channel division.

4.4 Screen Description

The status bar from monitoring screen, it shows DVR’s current status that included Date/Time,

Record, Motion/Sensor Detection, Manual Record, Text input and HDD’s record capacity.

51

Installaction & User Manual

4.5 Auto Switch Mode

There are System Standard modes and User Defined mode in Auto Switch mode. And Users

Sequence mode operates by the press [SEQ] button.

4.5.1

System Standard Mode

By [Auto] button, it can monitor auto switching of all channels.

Press [MENU] for the setting switching term or using mouse click menu icon from function menu.

Move to “Device”  “Monitor” from OSD menu.

Select “Seq. Switching(sec)” and set value from 1 sec. to 60 sec. At OFF set, auto switch mode does not operate

Auto Switch mode can be set in every division mode by the press [Auto] button.

Press [Auto] button once more to leave from Auto Switch mode.

4.5.2

User Sequence Mode

[Press [AUTO] button or click [Sequence] icon from Function menu with mouse.

Auto Switch model can be set from “Monitor” main menu.

52

Installaction & User Manual

There are 16 modes for user sequence mode.

4.6 Event Screen

When there is an event occurred, the green color [M] and red color [S] will be display from status bar. In case of [M] displayed, the camera name will be turned to green color, and it will turn to yellow when Motion Detection event finish.

In case of [S] displayed, the camera name will be turned to red color, and it will turn to yellow when Sensor event finish

53

Installaction & User Manual

It can be set to Pop-up automatically relevant screen when alarming.

Set pop-up period can be set into “Alarm Pop-up (sec)” inferior to “Monitor” menu.

At the simultaneous alarming in several channels, it displays the division as many channel as alarmed. For example, when 3 channels alarm, 4 divisions is displayed on screen. And press any button to return orginal channel.

1. If Alarm Pop-up Hold (sec) set to Off, Alarm Pop-up will not operate.

2. If Alarm Pop-up Hold (sec) set to Keep, it does not return to previous screen before press any button.

4.7 Zoom Screen Mode

From single full screen mode, press [FUNC] and D-Zoom button then select + button to activate zooming the image.

Default zoom screen locates to main center when press [ZOOM] button. Zoom image can shift left-right in 18 steps and top-buttom in 12 steps.

Use directonal key button to screen move.

Press [-] one more to return to original screen.

4.8 Pause Live Screen

Live screen can pause like PlayBack.

Press [PAUSE] to pause live screen and press [PAUSE] to return live screen.

54

Installaction & User Manual

4.9 PTZ Control

Connect PTZ controller to DVR and set relevant protocol from “Serial Setup” menu, then PTZ can operate while monitoring live images.

The method of operating PTZ, press PTZ button from

DVR’s front panel, or click PTZ icon from Function menu.

Below lists are protocol available in DVR

Model

BOSCH AutoDome, TC8560X-4

PELCO(P), PELCO(D)

Sony EVI-D3x

VT VPT-4x

AD SpeedDome

SungJin SJ372R1

Samsung SCC641

Panasonic WV-CS850

SDZ160/330, Samsung SPD,

Keyboard SCC3000A, Samsung SRX-100B

LG GAC-PT2

Keyboard KBD300A, WGI SPD1800/2600

WKC-100

Merit-Lilin FastDome

Elmo PTC200C

Canon VC-C4

HTC-230S

RVision

Elbex

Honeywell 755/655, HRX-2000, HTX-3000,

ScanDome2

VIDO

VICON

Hunt

ORX-1000

Manufacturer

Bosch

Pelco

Sony

VT

AD

SungJin

Samsung Electric

Panasonic

Samsung Techwin

LG

Honeywell

Honeywell

Merit

Elmo

Canon

DongYang Unitech

RVision

Elbex

Honeywell

VIDO

Vicon

Hunt

Sysmenia

55

Installaction & User Manual

Fine CRR-1600

Tokina

Kodicom KRE

Nuvico

LiveEye

Tokina

Kodicom

Nuvico

Press desired channel button.

Press PTZ button from front panel or click PTZ icon from function menu with mouse.

PTZ menu (Pan/Tilt, Zoom/Focus, Load Preset, Save Preset) will be appear.

Then press [Enter] button or click from mouse.

4.9.1 Pan/Tilt

This menu is used to control Pan & Tilt function at real-time monitoring mode.

Select Pan/Tilt from PTZ mode.

Control Pan/Tilt through directional key at front part..

4.9.2 Zoom/Focus

This menu is used to control Zoom & Focus function at real-time monitoring mode.

Select Zoom/Focus from PTZ mode.

Control Pan/Tilt through directional key at front part.

4.9.3 Load Preset

This menu is used to shift to Preset Set at real-time monitoring mode.

Using up / down button or mouse wheel to select the Preset Number.

Once preset configured then select Load and press Enter or click from mouse

4.9.4 Save Preset

This menu is used to set new Preset at real-time monitoring mode.

Control camera location using ‘Pan/Tilt’ and ‘Zoom/Focus’ menu.

Using up / down button or mouse wheel to select the Preset Number.

Once preset configured then select Save and press Enter or click from mouse.

4.9.5 Auxiliary On

This menu is used to utilize specific function in PTZ device at real-time monitoring mode.

Using up / down button or mouse wheel to select the Aux Number.

Press relevant Number button of specific function (Aux function is available to max 16 functions.)

56

Installaction & User Manual

4.9.6 Auxiliary Off

This menu is used to stop operation of specific function of PTZ device.

Using up / down button or mouse wheel to select the Aux Number.

Select Off and press Enter button or click from mouse.

4.9.7 Menu

It is to go into connected PTZ’s menu, using up/down/left/right and enter key from front panel for setting the menu, and press ESC button for exit the menu.

57

Installaction & User Manual

5.Playback

5.1 Playback Mode

5.1.1 Playback on Standard monitor (16 / 9 division)

Please, push play button in monitoring mode or mouse click play buttion in Function menu.

If pushing Play button or FWD button, video playbacks in forward direction at 1× speed.

If pushing REW button, video playbacks in reverse direcetion at 1× speed.

If pusing Playback button in multi-division monitor mode,

.

5.1.2

PLAY

Playback function

: Playback 1× speed. If using mouse, click Play button in Function

PAUSE

STOP

FWD menu.

Multi channel video will play back if pusing [PLAY] button in monitor mode. And it playbacks from the latest played back.

: Pause playback temporary. With mouse, click Pause button in

Function menu.

: Stop playback. With mouse, click Stop button in Function menu.

: Playback speed will be changed. (x1, x2, x4, x8, x16, x32, x64, x1/2,

REW x1, x2, x4 – in order), If pushing [FWD] button in live view, it plays back video 1 minute ago. Playback speed can be chanbed by pussing

[FWD] button.

: Reverse playback speed will be changed. (x1, x2, x4, x8, x16, x32, x64, x1/2, x1, x2, x4 in order)

If pushing [REW] button in live view, it plays back video 1 minute ago.

Playback speed can be chanbed by pussing [REW] button.

STEP FORWARD : If pushing [FWD] button on Pause mode, playback by each frame to

STEP REWIND

1/2 REWIND the forward. Push [PLAY] to return normal playback.

: If pushing [REW] button on Pause mode, playback by each frame to the reverse. Push [PLAY] to return normal playback.

: Play back at a half speed to forward direction.

1/2 FORWARD : Play back at a half speed to reverse direction.

5.2 SEARCH MODE

This menu is to playback specific time data from the time frame and searching log at Playback

58

Installaction & User Manual mode.

There are Time, Calendar, Event, Thumbnail mode.

Please, push Search button on the front panel or click in Function menu..

5.2.1 Time Search

Select date and time to search and playback video will be moved to the selected point.

5.2.2

Start-REC Time : The date and time of start-recording

End-REC Time

Search Time

Search

: The latest date and time of the recording

: Select the range of date and time for Search

: Execution button

Schedule Search

Year

Month

Date

: Select Year to search. With mouse wheel, user can change it.

: Select Month to search. With mouse wheel, user can change it.

: Select Date to search. With mouse, select the date and decide the

59

Installaction & User Manual

Time time by wheel.

: Select the time and push Enter button to plya back.

5.2.3 Event Search

User can search by all channels, some of channels, all events, motion detection, sensor in certain range. For change of date and time, with front panel, plese use top and down button. In case of using mouse, scroll the mouse wheel after selecting area. Searched result will be displayed on additional event window. Select and push enter or scroll the mouse wheel to move to the wanted date and time area.

Start-REC Time : Starting date and time of the recording.

End-REC Time : The latest date and time of the recording

Search Start

Time

: Input start date and time for search with direction button and push

Enter and change the value by Up and Down button. With mouse, click and scroll the wheel.

Search end Time : Input end date and time for search with direction button and push

Enter and change the value by Up and Down button. With mouse, click and scroll the wheel.

Event Channel : Select the channel for search

HVRM-T1600E : from Ch1 to Ch16

Event Type

HVRM-T800E from Ch1 to Ch8

HVRM-T400E from Ch1 to Ch4

: Select the event type for search

There are all events, motion detection,sensor, video loss, text type

5.2.4 Thumbnail Search

Search certain channel by thumbnail type. If select the searched thumbnail, selected date and time video will be played back..

60

Installaction & User Manual

Channel

Start Time

Interval

View video

Select video

: Select the channel and change the value by direction key or mouse wheel.

: Input the date and time for starting search and change the value using up-down direction key or mouse wheel.

: Set Interval value by Up-down button or mouse wheel.

: If pushing search button, 16 cycles will be shown based on start time.

Press [Func] to return to the search or use mouse wheel.

: Play back from the selected video of thumbnail search result.

With pressing Enter or clicking mouse, use can play back.

5.3 Copy

This is for copying recorded video. There are CD/DVD and RE4 and AVI type.

Copy function is supported to be used by user who has the authorization. For authority configuration, please, refer to 6.9.3 Security.

To use copy function, press [COPY] or Click Copy button in Function menu.

5.3.1 CD/DVD

This is copy function by using CD or DVD. CD or DVD will be automatically searched..

61

Installaction & User Manual

Type

Channel

From

To

Select Disk

Start

: Selec CD/DVD using up-down direction key or mouse wheel. Press

Enter and scroll wheel to change the value.

: User can select some or all channel among 16channels. Select the channel location and press Enter or use mouse wheel.

: Select start date and time to copy using up-down key or mouse wheel.

: Select end date and time to copy using up-down key or mouse wheel.

: Select the media to copy using Enter buttonr on Select Disk.

: Start Copy. Press Start button with Enter or click the left button of the mouse.

FAT32 format : Format USB memory or HDD by FAT32 type.

Do not use when copying into CD/DVD. First execute format and select FAT32 button and press Enter or click left mouse button.

Please, refer to the supported media list below.

DVD-R manufacturer CD-R Manufacturer

Mitsubishi(×16 recomended)

TDK(×16 recomended)

Imation(×16 recomended)

Sony(×16 recomended)

Mitsubishi(×52 recomended)

TDK(×52 recomended)

Imation(×52 recomended)

Sony(×48 recomended)

62

5.3.2 RE4

Installaction & User Manual

User can back up by HDD, USB memory and play back suing mini-player or Control Center.

Select channel position and press Enter or use mouse wheel to open the channel list like below..

Type : Select RE4 using up-down button or mouse wheel.

Channel : To pop up the channel selection window, press Enter or use mouse wheel.

Select Channel : use can select some or all channels and after selecting channel,

Start time

End time press Enter or click mouse left button.

: Set start date or time to copy. After selecting part for change and set the vaule using up-down key or mouse wheel.

: Set End date or time to copy. After selecting part for change and set the vaule using up-down key or mouse wheel.

Select disk

Start

FAT32 format

: Select media to copy. Press Enter on Disk list or click mouse.

: Start copy. Press Enter or click mouse.

: If USB memory or HDD are not formatted, format by FAT32 first and copy. To execute, press Enter or click mouse.

Reference : not perfectly finished backup file will not be played back in PC.

5.3.3 AVI

Use USB memory or HDD to copy certain part.

63

Installaction & User Manual

Type

Channel

From

Duration up/down key or mouse wheel.

: Select media to copy. Press Enter and select media or click mouse.

: Start copy. Press Enter or click mouse.

: Format USB Memory or HDD not formatted.

: Select AVI using up-down key or mouse wheel.

: Select the channel to copy by up-down key or mouse wheel.

: Set start date and time to copy. Time and Year by left/right button and date/time by up/down button. With mouse, click left button first and use wheel.

: Set copy length. Copy as selected time length from the start using

Select disk

Start

FAT32 Format

Caution : If copied file is not played back, please, install integrated codec first.

64

Installaction & User Manual

6.Configuration

6.1 Recording Structure

There are 4 modes in DVR recording. Configuration relation structure is like below.

Please, refer to the below each item for detailed recording configuration.

6.2 System Setup

Time and Disk and authority can be configured.

6.2.1 Date/Time

Time set should be configured prior to the recording.

Time configuration is very important to pretect the recording data. Time change on recording is not recommended. Time zone configuration value of factory default is “UTC 00:00 Dublin”

65

Installaction & User Manual

6.2.1.1 Time Setup

Caution: under recording, if user changes Time, it will affect time change on previously recorded video data in accordance with. Therefore, we recommend backup before time change.

Press Main Menu of Function or [MENU] button on the front panel.

Move to “quick setup” menu.

After selecting “Time” in Quick setup and press [Enter] or click.

Menu of time configuration 6.2 will be opened

To move to the sub menu, use directional key or mouse.

Time zone

Use left/right direction key or mouse wheel. To return to previous menu, press [ESC] or click right mouse button. (It is same as OSD menu)

Daylight saving

This menu is synchronized with time zone configuration menu. It means when daylight saving area is set, this function works. Daylight saving applicable area is all the same with Time zone of Micorsoft Windows.

Date format

With using left/right diection key or mouse wheel, configure date among “MM/DD/YYYY”,

“YYYY/MM/DD”, “DD/MM/YYYY”.

Time

With left/right direction key, use can move to year, month, day, hour in order and each configuration will be controlled by up/down key or mouse wheel.

Apply

User must push “Appl Date/Time” button. And you will see the below message box.

66

Installaction & User Manual

<Caution>

Except date/time configuration, other configuration records automatically, but

“date/time” configuration influences critical effect to HDD recording file system,

It doesn’t record automatically. To apply the changed value, user must press

[apply] button.

6.2.1.2 NTP Setup

NTP(Network Time Protocol) make time of connected devices synchronized. There are NTP server and client which get time signal from the server.

Sync NTP

Set NTP function on/off.

NTP Mode

Configure NTP mode of DVR – Client / Server / All

NTP Server Loc.

When NTP mode is client, it is on Enable. Configure yes or no wether NTP server is in Local

67

Installaction & User Manual

Network or Public.

NTP Local server IP

In NTP local server Enable, configure server ip. Input IP address of NTP server or DVR set by

NTP server In local network.

Interval

Configure interval of time sync.

Caution: If use NTP client mode, user must set NTP on.

6.2.2 Disk

7 It explains how to add or remove or format internal or external HDD.

Over Write(Auto Deletion)

If there is no space in HDD, old data will be deleed automatically.

Block Playback

This function makes recording data seen during the limited area.

For instance, if seting block playback by 2 day(Pic 2) among 10 days, Just allowed 2 days data can be played back.

68

Installaction & User Manual

Block Recording

This option is to record only the date you selected.

For example, if you select 3 days then DVR will record up to 3 days, and keep overwriting

3 days period of data

Disk Full Alarm Warning

If mounted Disk is full, alarm warning to user.

6.2.2.1 Disk

This is menu for the management of internal or external HDD.

Manage status, bad block, size, Yes or No etc.

Type : display location or type of disk.

Int A (Internal A HDD), Int B (Internal B HDD), Ext (External HDD)

: HDD model name.

: display bad block. In HDD. If no proble, “0” will be displayed. Others are

Model

Bad Blk

Size

Enabled

Not shown anything at all.

: Display HDD size by MB unit

: Make HDD enable mode or disable mode.

Yes: enable / No: Disable

In case HDD YES

- Enabled : Press [Enter] in No mode or scroll mouse wheel. Notice window pops up and show user the message like below.

- Caution : This Disk is not available without format. Will you format Disk?

- If selecting No, keep previous data and HDD will be Enable to use.

- If selecting Yes, delete previous data and HDD will be Enable to use.

69

Installaction & User Manual

In case HDD No

- Enabled : In Yes mode, press [Enter] or scroll mouse wheel and notice window pops up and show user the message like below.

-Caution, will you remove Disk?

- If Yes, user will find the message “Disk is removed” on the bottom and Enable status will be No.

- HDD is not used.

- If No, keep previous HDD without change.

6.2.2.2 Disk Status

Temperature and status of HDD will be shown.

6.2.3 User Setup

There are administrator and user and administrator can use all functions. The max. number of user is 10 person. Each user can use the function allowed.

Check

If Check item is configured all by X[Check-1], all users can use all functions.

70

[Check-1]

[Check-2]

Installaction & User Manual

In the other hand, if all are set by O[check-2], all users can use the functions in accordance with

Each users authority.

For example, as you can see the below picture, User1 can use PTZ, Relay off, power On,

N/mike functions are available, user 2 just can use menu and N/mike functions.

<Reference>

Admin Password is “12345” in factory default and from user 1 to 10 in order

“11111”,”22222”,.. and user10 is “00000”. In case of 9 channel DVR user, press “0” for figure 0, in case of 16 channel, press button “10”

Password change

Select user  Input password and press change  Press Yes

Password input box is displayed. Password can be input with front figure button or text input window. After inputing 8 digit figure, click “Change” button.

After that, message pop up window will be shown and press “Yes”.

Authority

User can use only authorized functions.

If user 1 has PTZ use authority, when pushing PTZ button, authority check window will pop up and user should inpt the password and if it is correct, user 1 can use PTZ function. If password is wrong, message box “Wrong password” will be displayed.

71

Installaction & User Manual

[Authority check]

[Password error]

6.2.4 Utility

Configure the name of DVR, remote controller ID, Language.

DVR Alias

Set the name of DVR.

DVR Keyboard ID

This menu is to set the address of keyboard when using all functions of DVR by keyboard.

72

Installaction & User Manual

Factory default is “1”. If user want to control various DVR by one keyboard, its address should be set with the different value.

Remote Controller ID

Max 16 remote controller ID can be set and one remote controller can manage 16 DVRs.

Registration order for Remote controller.

Make remote controller direction to DVR.

Press ID button and figure in accordance with configured remote controller ID.

If IDs are matached correctly, DVR buzzes.

Use Remote controller.

Language

Select Language to use.

Firmware Update

Can update firmware by USB Memory.

Insert USB memory to USB port.

Press Firmware Update button.

Select [YES] on the pop up window.

System will reboot.

Firmware update is done.

System Log

System Log shows boot status of system and user and configuration etc.

.

73

Installaction & User Manual

Factory Reset

Change all configuration value by factory default.

Caution : This function is allowed only for system administrator.

Encording Policy

Recording Prior / Networking Prior available to set

74

.

Installaction & User Manual

When you select Networking Priority option then DVR will compress additional resolution QCIF, and let remote client user monitoring QCIF with low bandwidth condition.

When you select Recording Prior option then DVR will sending same resolution as recording resolution.

< Caution >

1. The DVR will be re-booting when user select Encording Policy.

2. Recording performance will be reduce when user set the Recording Speed/Quality andafter select the Networking Prior option.

6.3 Network

This is menu for configuring network.

Type

Configure type of Network (Ethernet/xDSL). If connected to cable modem or Lan directly to DVR, configure by “Ethernet”.

If DVR connects to xDSL- one of PPPoE type, configure xDSL. But if it is not type of PPPoE,

75

Installaction & User Manual configure ‘Etherent’.

DHCP

With DHCP (Dynamic Host Configuration Protocol), all hosts connected to Lan can get Public IP address temporary.

If LAN has DHCP server and it is active, DHCP server allocate IP address to DVR.

Mostly middle and large network use DHCP server in LAN, but in case of small network,

NAT(Network Address Translation) of HUB is general.

IP Addr

IP Address is for the connection between DVR and Control Center and also for web connectionfrom Webviewer. (But, Net Mask, Gateway should be configured.)

Net Mask

Net Mask makes range of IP address available. It should be received from network administrator.

Gateway

Gateway is necessary to communicate IP, it should be received from network administrator.

DNS1

DNS1 is mandatory item to regist and use WRS and it should be asked to network administrator.

Additional DNS

Additional DNS is alternative when DNS1 has a problem.

Port

Port is necessary for Control Center and Webviewer connection.

Reference : Basic port is 80 and if using PPPoE modem and AP, be careful typing port number.

Bandwidth

Menu for configuring network data transmission capacity. Without any additional configuration, it works but if user want to set, please, ask for administrator.

76

Installaction & User Manual

6.3.2 xDSL

DVR is connected to xDSL line and use PPPoE type, please change type by xDSL and configure user ID and Password. User ID and Password should be same as xDSL.

User ID/Passwod

Configure user ID and Password.

Status

It shows connection status of DVR.

6.3.3 WRS

If DVR is connected to Cable modem or xDSL modem, IP address is changed at every connection to ISP. In this case, changed IP address can not be known. If DVR using static IP register into WRS server, changed IP address can be known easily when it connects to DVR.

To register Static IP to WRS, please refer the following to set .

WRS Interval

For continuous registery, register inverval should be set to ‘WRS Interval’. According to set value of static IP address, it renews the information in WRS server regularly. If user registers

77

Installaction & User Manual the interval ‘0’ or DVR does not transmit any data for 2 days, the data is removed from WRS.

WRS URL

This menu is to set server address to register. WRS addresses that Hunt operates now are www.webgateinc.com or mycam.to.

6.4 Device Setup

This menu is for configuring each camera connected to DVR.

There are [name][Status][Color/balck or white][Brightness][Contrast][PTZ] etc.

Caution : NTSC and PAL camera can not be used at the same time.

If changing the camera from NTSC to PAL, system should be rebooted.

Configured value will be applied to monitoring and search at the same.

6.4.2 Camera Setup

Select the camera to configure in Channel menu.

6.4.2.1 Title

Configure camera name.

If pressing [Enter] button or click mouse, test menu will be shown.

For text string, text input box will be shown.

78

Installaction & User Manual

Use directional key for text input.

With mouse, just click the text.

Select the text using up/down and left/right button.

After selecting the text, press [Enter].

To delete the text, press [  ] button.

To make a space between letters, press [  ].

6.4.2.2 Using Channel

Configure wether using camera or not.

After pressing [Enter], select it using left/right key or mouse wheel.

If user wants to enhance the recording or network monitoring speed, please, set the channel disable.

6.4.2.3 AGC (Auto Gain Control)

AGC is the function to control the range of video signal input from carame connected.

Configure Enable/Disable using directional key or mouse wheel.

6.4.2.4 Brightness/Contrast

It can control Brightness and Contrast of video. After press [ENTER], use left/right button or mouse wheel to set the value wanted from each “–9” to “+9”.

6.4.3 Monitor Setup

Main monitor provides all function which DVR supports and with spot monitor can use single channel conversion.

79

Installaction & User Manual

Covert channel

With Covert menu, user can covert the channel in Live/Playback mode

In Covert menu, all channel list will be shown and press [Enter] buttion and click mouse to tick the channel. Checked channel will not show the video in Live/Playback.

User sequence configuration

User sequence can be edited. There are 16 user sequence mode and its interval is from 1 to

60seconds.

Multi mode

The DVR has 3 predefined screen modes. 4E(4channels), 9B(basic 7 channels and additional 2 channels),10A(10 channels).

The way to composing

The way to conpose screen is selecting the target and after selecting right window and press

[Enter] button or use mouse. If channel selection is down, press [ESC] button or click mouse light button.

DVI Resolution

There are 9 resolution can be select 800x600@56Hz, 1024 x 768@60Hz, 1280 x

720@50Hz,1280 x 720@60Hz, 1920 x 1080p60, 1920 x 1080i50, 1920 x 1080i60, 1920 x

1080RB.

Display information

Display information is to configure which information will be shown on live view and playback view. In live view, time, channel name, event, recording status, HDD, remote controller ID, text can be set and in playback view, time,command,channel name, event, text can be configured.

80

Installaction & User Manual

Scan Mode

Support Over Scan / Under Scan Monitor.

6.4.4 Audio Setup

With this menu, user can configure Voice Channel, Audio recording, Volume, Synchronization,

Mixing..

Voice Channel

Select audio to use

Recording

Configure yes or no of using audio recording. If no, audio will be out only in live view and if yes,

Audio will be out in both view modes.

Volume

Configure volume by +, - direction

Synchronize Video Channel

Configure which channel is matched with the input audio. But this function is applied only on recording. Audio out in live view will be covered in Voice Mixing below. Default set is Auido no.1 to channel no.1.

Voice mixing

81

Installaction & User Manual

Select audio in live view. If setting by “All”, input audio will be out in eery channels and if configured certain channel, input audio will be out on the selected channel only.

6.4.5 Text Setup

Configure Text in Device menu.

Recording

Set On/Off of recording against Text input

Sync Text with

Select channel to synchronize with text.

Header check

It has the various type of data input from the external device (Access Control, POS, ATM etc).

Like VSI Pro, VSI Pro Hydra, and Star Finger 007, it is not needed when the protocol of these device have implemented on the device. If not, this is the parameter to analyze how the one of data is constructed from the text data that is input continuously.

Namely, all data has the first and the end. Header indicates the information that already inserts

82

Installaction & User Manual to inform its starting. Therefore, Header information is defined here to acknowledge its starting of a data. The reason of 2 Header is to detect maximum 2 data out because each device can output various datas.

Delimiter

Delimiter value can be different according to the manufacturer, please, refer to the product manual or seller.

Time out

Following lines defined here means maximum number of text line from one data. Even if there is standized data, there can be a short and long data. For example, there are 3 lines to write names on ATM. But some may need only First name & Last name to register. Which it means requires only 1 shorter than other ATM users. It is to decide the last line of the one data register as final complete data to save after an hour’s consideration of register later because DVR can not recognize it automatically.

Lines

Define how many lines will be shown.

Caution : external device can not be recognized, please, ask to the seller.

6.4.6 Serial Setup

DVR has 3 serial port. One is RS-232 and the other 2 ports are RS-485.

Serial Port

Select Serial port.

Device

Select the connected device.

83

Installaction & User Manual

Interface

Configure which interface user uses.

COM1 is for RS-232C, COM2 and COM3 is for RS-485

Baud rate/Parity/Stop Bit/Data Bit

In put suitable value according to external device.

6.4.6.1 PTZ Setup

Additional configuration for PTZ Address, PoirtPTZ.

PTZ Home

Shift to Preset assigned if it has no movement in certain time while PTZ control .

PTZ Idle Time

If it has no movement during configured time, shift to PTZ Home.

PTZ Port

Select Port for PTZ

PTZ Address

Configure the address configured in PTZ.

6.5 Event Setup

There are 5 items such as event, Text, Sycn Event,Preset, System event.

84

Installaction & User Manual

6.5.2 Event Check

There are 3 items – Always, not apply, Timezon.

In case of Timezone, with similar configuration window like schedule, user can configure event per weekday/time.

• INDEX : Schedule configuration from 1 to 50

• Weekday

• Time

• Delete : delete INDEX

How to configure

If configuring INDEX,weekday,time, they are displayed on the table.

If clicking and selecting start time and end time of recording on the table, Index,weekday,time will be shown on the table.

How to delete

Select INDEX and click Delete buttion.

If clicking Delete buttion without selecting INDEX, previously selected INDEX will be deleted and from the latest INDEX, it will be deleted in order.

How to change

85

Installaction & User Manual

 After selecting INDEX, change directly weekday,time.

6.5.3 Sync Event

Configuration for Event synchronization.

Event Action

There are 6 actions – relay 1 to 4, buzz, E-Mail.

Action Duration

Action Duration runs if relay and buzz are configured, and goes on during the configured time. E-mail works by configured time interval.

Normal Event Source

User can configure Sensor, motion detection, V-loss, Text.

Sensor

16

MD

16

V-Loss

16

Text

1

86

Installaction & User Manual

System Event source

System Event source can configure Bad block, Disk full, Fan error, authorization failure,

WRS registeration failure.

E-mail address

Input E-mail address to get event alarm by E-Mail.

Sender Address

Not mandatory but necessary for receiver to find out which DVR sends event.

Including Picture

In general event, when sensor, MD, V-loss events are generated, the event information and channel video will be sent to e-mail together.

But system event just send system event information.

6.5.4 Motion Detection

87

Installaction & User Manual

Channel

All or certain channel.

Sensitivity

Sensitivity can be configured from min.1 to max 10.

Area

Select detection area.

User can select all or certain channel.

User Area

When selecting per channel, it can be configured.

1 grid size is 22x15 and factory default value is All. If pushing user area, configuration window for detection area..

With direction key, select area and press [Enter] or click mouse. And press “ESC” button or click right mouse button, shift to the previous menu.

88

Installaction & User Manual

6.5.5 Sensor

This menu is to setup the existing sensor input and type of sensor.

16 input Sensor has 2 types, Normal Open(N.O.) and Normal Close(N.C.).

6.5.6 Preset

In PTZ function, make configured preset work according to sensor input.

Please, configure preset per PTZ.

After selecing channel in preset menu, select event to work preset.

Event can select sensor,MD,Text, its preset can be configured up to 16.

89

Installaction & User Manual

6.6 Recording setup

There are 3 mode for recording – schedule recording, manual recording, event recording.

Schedule recroding records according to the configured schedule. And manual recording records via pushing “REC” button and event recording records when events are on.

6.6.2 Program setup

Using [Program], adjust frame rate and quality and resolution and configure recording program for Manual&Event&Schedule.

In event recording, one channel can record up to its max frame rate and if setting 2 channels as event recording, their recording frame rate will be adjusted automatically.

Program

There are 26 programs from A to Z composing recording quality and resolution per channel.

Please, refer to 3.5 programe configuration value.

CH (Channel)

Display the channel figure.

R (Resolution)

There are 3 resolutions - D1(704x480), Half D1(704x240), CIF(352x240)

F (FPS)

It means frame per second and can select 1 to 30fps. Max. frame can be changed according to the configuration.

Q (Quality)

There are 5 recording quality - Q5/Q4/Q3/Q2/Q1. Recommended quality for event recording is Q3.

Max R/F

90

Installaction & User Manual

Max R/F shows the number of frame available according to the selected resolution. For instance, if it is set by 30fps at CIF, it means that the channel can record up to 30frame at CIF resolution.

Reference : how to calculate recording performance

D1[704x480] = 2 x Half D1[704x240] = 4 x CIF[352x240]

If 480 frame can be recorded at CIF resolution, instead of it, 240 frames at Half D1 and 120frames at D1 resolution are possible.

• In case that the channel is configured as disable

Configuration method : Menu > camera configuration > channel : “Disable” – (the channel in gray)

For example, all channels can be configured as 30fps at CIF all the same. If one channel is configured as disable, system has resource avaiable as much as 30fps at CIF. And if conbining it with other 30fps at CIF, other channel can be configured as 30fps at Half D1.

• In case that the channel is configured as 0 fps.

Another channel can not use resource room as much as CIF 30fps. It is because the channel configured as 0 fps needs 2~3fps at least for network..

Reference : the relation in between general recording and event recording.

When Event is triggered, records event recording according to the configured value. Recording

Performance of DVR depends on the product. For example, if HVRM-T1600E is set as manual recording at CIF 480fps and event recording at CIF 480fps, it can not be over CIF 480fps.

Therefore, it should be configured within CIF at 480fps resource.

• Event configuration value on CIF 480fps

If you configure recording all channels at CIF 30fps, available event recording confirguration is CIF 30fps, Half 15fps, D1 7 fps.

If you want to configure channel no.1 as D1 30fps, you should adjust the other channel recording configuration.

• On event recording of multi channel

With mulity channel event recording, if configured recording value is over the system max performance, general reconrding will keep their recording configuration and event recording will be balanced down equally.

6.6.3 Manual/Schedule recording setup

With the change of recording mode, manual recording or schedule recording can be at one’s

91

Installaction & User Manual choic.

And their resolution , frame rate , quality will be in accordance with the program.

.

6.6.3.1 Manual Recording

Only in manual & event recording, manual recording runs and when pressing [REC] button, recording starts. If you want schedule recording, recording mode should be Schedule & Event.

6.6.3.2 Schedule Setup

It records according to the programmed schedule automatically. Make recording mode Schedule

& Event and configure day and time.

92

Installaction & User Manual check and select each program default vaule and select one of 26 program from A to Z or several programs. Below picture show program A.

• INDEX : Schedule unit from 1 to 50

• Weekday : Set the day applicable

• Program : Set recording program(A~Z)

• Time : Set time applicable

• Cancel : Cancel per INDEX

Configuration

Configure INDEX, weekday, program, time.

If selecting recording start time and end time on the table by mouse, its Index,weekday,program will be displayed.

Deletion

Select INDEX and click Delete button.

If clicking delete button without INDEX, previously selected INDEX will be deleted first and after that, from the largest INDEX in order.

93

Installaction & User Manual

Edition

 Select INDEX to edit and change weekday, program,time directly.

 In case that INDEX 50 are all configured, select the time zone to change by mouse click and click the time again, previouse configuartion will be deleted and new configuration will be shown.

 Caution : If selecting the same time twice, “!” will be shown on the chart.

 When configuring time sector, previously configured time can not be included.

De-interlace

Set playback deinterlace On/Off.

It works on Full Dq recording. In “On” status, screen vibration of paused Full D1 video will be redcued.

6.6.3.3 Event recording setup

Select resolution and frame rate and quality for event recording.

There are 4 trigers – Sensor, Motion detection, Text, Digital input.

First, select the program and check resolution and frame rate and quality of the channel.

(refer to 6.6.1, program configuration)

Event recording can syncro manual&event, Scheduel&Event.

Select among Manual&Event, Schedule&Event in “Recording mode” of [Record configuration]-

[recording].

Reference : Please, check below to configure event recording.

1. Select one of Manual&Event, Schedule&Event.

2. In program configuration, set frame rate by 0 fps in general mode and only configure Event frame rate.

94

Installaction & User Manual

3. Set Event applying time.

Event Time configuration

Configure time for event recording and there are 3 mode – Always, no use, Timezone.

In “Always”, event works all the time and in “Timezone”, works during configured time.

Configuration of Timezone is similar with schedule configuration and can configure weekday,time for Event.

• INDEX : Set from 1 to 50

• Weekday : Set weekday applicable

• Time : Set time applicable

• Deletion :Delete per INDEX

Configuration

Configured INDEX,weekday,time will be shown at once.

Select recording start time and end time in order and its INDEX,weekday,time will be shown.

Deletion

Select INDEX and click Delete button

If clicking delete button without INDEX, previously selected INDEX will be deleted first and after that, from the largest INDEX in order.

Edition

 Select INDEX to edit, and change the values.

 In case of being configured by INDEX 50, click and select time to eidt and if clicking the time table again, previous configuartion will disappear and new configuration will be shown.

95

Installaction & User Manual

96

Installaction & User Manual

7. Web Viewer

WebViewer is Web application program loaded to monitor real-time image or to minitor the images recorded through Web browser to PC located remotely.

WebViewer is divided into Login page and Monitor to do monitoring real-time images, Playback to replay reocorded images.

7.1 System requirement

Minimum Recommendation

CPU

Main Memory

Video Memory

Display

HDD

OS

Intel Pentium 4 / 3.0GHz

1GB

Core2duo E6750 or higher

2GB or higher

128MB 512MB or higher

1280 x 1024 (with 32bit color) or higher

1GB or higher

Windows XP Professional(over SP2) / Window Vista Business( over

SP1)

DirectX 9.0 or higher Others

7.2 Login

After input IP address that set to system, then WebViewer Login page will be connected.

97

Installaction & User Manual

Input the set of User ID & Password, click ‘LOGIN’ to access.

If didn’t change the password in Control Center, ID and Password will be admin/12345.

ID can not be changed.

7.3 User Setup

To access WebViewer, user authority and password can be changed in DVR or Control Center configuration

In account menu, user password can be changed.

Basic admin password is “12345” and user password is like “11111{“, “22222” ~~, user10 is

“00000”. Valid password is 5 digit.

98

Installaction & User Manual

Authority configuration is almost all the same in DVR and Control Center. But quick recording, backup, audio, yes or no of using channel are only possible in Control Center.

7.4 Browser available

WebViewer is optimized to Windows Internet Explorer 6.0 or higher in PC for smooth use.

Webviewer Installer

Login page provides manual installation program to use WebViewer function.

PC that access to WebViewer first installs ActiveX to use WebViewer’s function. At this time when installation is not smooth, installation program needs to download from Login Page and install manually.

Caution

When install WebViewer Installer, it must close all program related to Control Center. It might not be efficient to install.

7.5 Monitor

When it is authorized with User ID & Password input at Login page, it moves to Monitor page.

At Monitor page, monitor real time image of cameras connected to DVR, or it can control PTZ camera, Relay, and use Microphone function according to user’s authorization.

Study introduction of each Monitor part and functions of the page.

7.5.1 Screen division and changing video position

When access to first Monitor page, it is displayed into 9 division, 16divisions or 32 divisions according to number of channel.

99

Installaction & User Manual

It can to change to 1, 4, 9, 13, 16, 25, 36 divisions by click number on top of page.

Also, it can change to 1 channel mode by click any one of channel image.

Double click on one of the playback screen to convert in 1 channel mode.

니다 .

After conversion to 1channel mode, double click on screen to return to previous division channels.

At division screen, it can change screen location.

If 3channel image moves to 6ch, drag 3ch image and drop on 6ch location so as to exchange between 3ch and 6ch image

7.5.2 Move to Playback

100

Move to playback with clicking the above image.

7.5.3 Channel On/Off

Installaction & User Manual

It is On/Off button for the Channel located to left in page. Click the channel wanted to On or Off.

And Default is On.

7.5.4 Sensor Indication

The icon indicates when sensor occurs in system

When it sensorsed, relevant sensor icon comes to Red, and indicates sensor number of video.

7.5.5 Relay operation

It can On or Off Relay of the unit. Click the number button to activate Ralay On, then the incon changes from Blue to Orange color.

Disabled Relay button refers to do not support and relate to this unit.

Relay is need user’s authority. Refer to user manual in the unit for the setup of User’s authority of Relay.

7.5.6 Using Microphone

It can On or Off the use microphone.Default is Off and it is changed from the Blue to Red when click the button for the use Mic.

101

Installaction & User Manual

7.5.7 Event Data

It shows real time event data occurred at the bottom of monitoring page.

Indicated Event data list are as follow..

(Table, Event Icon)

Icon Function

,

Motion Detect On

Sensor Input

, Relay Output On

,

7.5.8

7.5.8.1

No Video, Video Detected

Video Recording & Save Saving

Video Recording

During monitoring, it can record max. 10 minutes of video by click Quick Recording button “ ”.

During Quick Recording, recording time is indicated on video.

During video recording, if click Quick Recording button “ ” to stop recording and open the dialogue box to store recorded files. At this time, user can save it to the directory with any file name by user.

Saved recording file is saved into “*.re4” file format. re4 file can playback through Control

Center Playback program or Mini Player program.

7.5.8.2 Saving Vido

There are 3 types for saving Video - jpg, bmp, eye, saving means the function to record 1 frame

102

Installaction & User Manual of current monitoring channel.

To save video, select the channel and click right button of mouse. Ans select “Save As” and point out the location and press Save button.

7.5.9 Using PTZ

Among the icon on top of video on monitoring, click ‘PTZ’ to acitivate interfacing to control Pan,

Tilt, Zoom, and Focus. But, when PTZ camera is connected and ready to set PTZ, the button is acitavated to use the functions.

Pan, Tilt Control

Mouse is on the image and click right button to pop-up menu for the selection or “PTZ” or button. Then it show Cross line on the middle of screen and click image to operate Pan, Tilt. At the middle click Left/Right direction to control Pan, and Click Up/Down direction to control Tilt.

Click as far from the middle to activate Pan/Tilt faster.

Zoom, Focus Control

Move mouse to the edge of left & right to see slide bar for Zoom, Focus.

The unit Area Zoom In available has Zoom Zero operating button. It can Zoom In/Out using slide bar at left of image, left slide bar can control Focus.

Move to Preset

In case of Preset set, Mouse on image press right button for pop-up menu and “Goto Preset” is indicated additionally. When select Preset list, it moves to Preset position selected. Preset should be set up by user in advance.

Activating Auxiliary

In case of Preset set, “Auxiliary” is indicated additionally, and it operates action when select registered menu.

103

Installaction & User Manual

Reference

Supported PTZ camera list can be refereed to ‘4.8 PTZ manipulation.

7.5.10 Using Audio

In case of Channel setup sync with Audio, press right mouse button on the image to activate pop-up menu to “Listen” or activate Audio listen button. First default is Mute. In case of listening

Audio, select pop-up menu or button. After cancelling mute, control audio volume. It can mix several channels of audio

7.5.11 Closing Video Channel

Cancel for disconnection of image monitoring by click ‘Close’ at top right on screen, then it comes to black screen.

To reconnect the channel disconnected, it can reconnect relevant channel using ‘Channel

On/Off’ menu.

104

7.6 Playback

Installaction & User Manual

This page is to playback recorded images, and user who has authority of ‘HDD’ among user ID or administrator can use this function.

Playback that is made up 16 divisions can play the images by searching through calander by recording period and moving the period. It can backup recorded image and also print Pause image or save to Bmp file.

7.6.1 Video Division & Changing Channel

Playback supports 1, 4, 9, and 16 divisional screens. It can select division using menu on tip of page as above picture. 32ch DVR can call the channel using Group moving button as follow.

If screen shows 4 divisions CH1~CH4 and look for next CH5~CH8, it can change the channel with click ‘Next’ button. Press ‘Prev’ button to call for previous channel group CH1~CH4.

7.6.2 Image recording

It can save playback image to BMP file.

Click mouse to channel to save. Dotted line will be surrounding to the selected channel, and click ‘Save’ button.

105

Installaction & User Manual

Save Iamge dialog box appears, then it can input message or select channel name, date, event data.

Press ‘OK’ to open dialog box for the saving location, then save bmp file.

7.6.3 Print

Select image with mouse for the channel to print image saved, and then click ‘Print’ button.

Window comes to input Memo, and click ‘OK’ button to print the image through the printer connected.

Print material includes ‘Printing Date’, ‘Channel name’, ‘Recording Date’ ‘Event’, ‘Memo’.

7.6.4 Backup

There are re4 (Mulit channel) and avi(single channel) Set From, To time and select the channel for backup

Point out the location for backup. Input in Password/Verify.

106

7.6.5

Installaction & User Manual

Web Monitor

Click ‘Go’ button at top of page, and it can move Web monitor page.

7.6.6 Channel On/Off

It is the same function like Channel On/Off function at Web Monitor.

It is Channel On/Off button located on right of Page, and click On or Off page for wanted channel. Default is On.

Disabled Channel button refers to do not support and relate to this unit.

7.6.7 Saving time & Checking Rec, Capacity

It indicates total capacity of HDD & remains and shows Starting date & Last date of recording.

Also it shows percentage (%) for HDD capacity.

7.6.8 Searching Calander

Recorded date is abled in black color, and others unrecorded date disabled in grey. Select button after select date & time so as to playback images on the date & time selected.

When click ‘Go To’ button, it indicates for 24hours from the time selected at left bottom. As above picture, it is possible to change the time zone with ‘24h’ button

107

Installaction & User Manual

7.6.9 Functional function at the buttom of monitor

① Indicates playback range of recorded image.

② Press button as the time set at (5) so as to change the time zone to playback in forwarding and backwarding.

③ From left button, it can ‘Move a frame back’, ‘Play backward’, ‘Stop’, ‘Play’, ‘Move a frame forward’.

④ It is the function to set play speed. After click the button, it can set the play speed ‘0.5x,

1x, 2x, 4x, 16x, 32x, 64x, and All’.

⑤ It is the function to set play area. After click the button, it can select play area ‘10min,

30min, 1hour, 3hour, 6hour, 12hour, 24hour’.

⑥ It can select DirectX use or not. If check DirectX mode, it can play image into Direct

Draw based on graphic card and performance of PC.

⑦ It is the function to set audio play or not, and volume.

108

Installaction & User Manual

8. User manual for Mobile Viewer

Mobile viewer is viewer service to monitor video via mobile device.

To access mobile viewer, user uses mobile device supporting Wi-Fi or smart phone or 3G.

8.1 Log-In page

Below picture is Mobile viewer log-in page.

To access log-in page via mobile viewer, please, type the address like http://IP/mvmenu.html.

Below image is accessed login page to http://211.53.133.187/mvmenu.html .

To do log-in, please, enter ID/PW and select Resolution and channel number and cycle and push [0] Start View button.

8.2 Monitoring page

This is the page on Log In.

It shows selected channel video and functions right below the screen.

109

Installaction & User Manual

For functions, please, refer to the below.

[0] MENU : Move to Log In page

[1] CH- : Move to the previous channel.

[2] UP : Move to upside of Pan Tilt movement

[3] WIDE : Zoom Out action

[4]  : Move to left side of Pan Tile movement

[6]  : Move to right side of Pan Tile movement

[7] CH+ : Move to the next channel

[8] DN : Move to downside of Pan Tilt movement

[9] TELE : Zoom In action

110

Installaction & User Manual

Trouble shooting

1. DVR booting failure

1. Check the power

2. Check Power cord

2. No video on monitor

3. Check monitor power

4. Check cable between DVR and monitor

5. Check monitor cable port

6. Check DVR power is off

7. If monitor video is gray mode, check the camera type(NTSC/PAL) and reboot.

3. No video in some of channel

8. Check Camera power

9. Check Camera video input

10. Check DVR input port

11. Check On/Off of Activity configuration of Screen

12. Check Covert configuration of Monitor

4. No recording

13. Check Disk Manager if HDD is mounted or not

14. Check recording configuration

5. No playback

15. Check recording configuration

16. Check button

6. If video is too much bright or dark

17. Check Camera configuration

18. Check and dismantling power calbe near video cable.

19. Check Brightness, Contrast of screen

7. Remote controller is not working

20. Check Remote controller battery

21. Check Remote controller ID

22. Check Remote Controller manipulation

8. If front button is not working

23. Check DVR Power

24. Check Screen Lock

111

Installaction & User Manual

9. If network is not working

25. Check if Network cable is connected

26. Check DVR IP

27. Check Computer IP

28. Ping Test

29. Check PC specification if Webview video is not shown.

10. The cases necessary to contact the shop

30. In case of extraordinary working(ex: noise, smell or fume)

31. Connetor breakage of power cable

32. In case that rain or water is in the product

33. In case that liquid or foreign is in the product

34. If the product is not working in accordance with the manual.

35. In case of breakage from product dropping

36. In case that product performance drop dramatically

112

Installaction & User Manual

The way to check the manufacturing date

It can be checked with its S/N(Serial Number)..

S/N : Serial Number

It means composite 12 digit number with product model name and production year,month, and week. It can be found on the attached label attached on the bottom of product or system info of configuration tool or system information 1 of DVR Func menu.

Serial Number Structure

□ □ □ □ □ □ □ □ □ □ □ □

Year/month

Internal check number internal check number

Model number

(1) 1~2 digits : Identify Model name of product

(2) 3~8, 8~12 digits : Hunt internal number

(3) 5~6 digits : Manufacturing year

(4) 7 digits: Manufacturing month

Please see the below table for manufacturing month.

.

Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

1 2 3 4 5 6 7 8 9 A

The example of verifying manufacturing date using serial number

The below S/N can be verified as following as:

『 EB0009200707 』

(1) “EB” means “HVRM-T1600E”.

(2) “092” means it is produced in “2009 Feb”

(3) “00707” means the serial number.

B C

113

Installaction & User Manual

Available HDD

Plase ask to seller about HDD available with DVR.

Compatitable CD/DVD list

DVD-R manufacturer

Mitsubishi(×16 recomended)

TDK(×16 recomended)

Imation(×16 recomended)

Sony(×16 recomended)

CD-R Manufacturer

Mitsubishi(×52 recomended)

TDK(×52 recomended)

Imation(×52 recomended)

Sony(×48 recomended)

Specification

Video input

Video input standard

Connectors

Loop out

Main Video output

Vout 1,2

NTSC or PAL auto detect

16ch analog video inputs BNC connector

Auto terminated loop out

Vout 3,4 output via BNC & DVI(VGA)

1,4,9,10,16 mode

User defined sequence / alarm pop-up

1920x1080, 1280x720, 1024x768, 800x600 at

DVI port output via BNC

1,4,9,10,16 mode

User defined sequence / alarm pop-up

Recording

Compression

Resolution

Rate

Quality

Mode

Schedule

Playback

Mode

H.264 / JPEG

CIF/Half(2CIF)/D1(4CIF)

480 at D1

5 levels

Manual & Event / Schedule & Event

24hrs / 7day

Instant playback / Search

Speed

114

Search Type

Block Playback

Event & Alarm

Event source

Event check schedule

Event Action

MD Area

Sensor input

Text input

System Alarm

Alarm source

Alarm action

Audio

Input/output

Compression

Direction

PTZ

Protocols

Network

Interface

Type

DDNS

Bandwidth Limit

NTP

Users

Streaming

Security

User Level

User privilege

IP Filtering

Storage/Backup

Installaction & User Manual

Time, Calender, Event, Thumbnail

1day ~ 31days

MD, Sensor, Text

24hrs / 7day

Recording, Relay, E-mail, Buzzer, Pop-up,

Warning Message, PTZ preset

22x15(NTSC), 22x18(PAL) dry contact (N.O. or N.C. selectable)

POS/ATM support, AVE VSI Pro/Hydra support

HDD fail, HDD almost full, Fan fail, Pwd fail,

DDNS fail

Warning message, buzzer, e-mail, relay

4 RCA input, 12 D-Sub input, 1R CA output

16KHz, 16bit sampling ADPCM

Both

32 models including Bosch, Pelco, Sony, Meritlilin, Honeywell

1 10/100 Ethernet

Fixed IP, Floating IP, ADSL supported supported

Server/Client/Both

10 monitoring, 2 playback

1 H.264 same as recording

1 additional H.264 smaller than recording

1 JPEG for e-mail sending or mobile

1 admin, 10 users

Menu, PTZ, Relay, PB, Power on/off, Backup supported

115

Installaction & User Manual

Storage Devices

File System

Capacity

Backup type

Backup device

S.M.A.R.T.

Serial & I/O

Serial port

Sensor input

Relay output

Controller

Device

Software

WebViewer

Mobile Viewer

CMS

SDK

Environmental & Physical

Dimension

Operating temperature

Power

Power consumption

4 internal SATA HDDs, 2 external eSATA I/F

Proprietary file system, data-loss protection against power-failure

Max 8TB multi-channel or single channel avi file internal CD/DVD or USB drive

Temperature and Health

1 RS-232C, 2 RS-485

16 dry-contact

4 relay

Front panel, IR remote, Joystick KBD, Mouse

Monitoring / Playback

Monitoring with PTZ, iPhone & BB supported

Control Center Standard, max 1000 clients

ActiveX(COM) SDK

W : 445.0, L : 417.8, H :88.0

Operating: 41 ~ 113 degrees F.

AC free volt (100 ~ 240VAC)

Max. 75W Typical 50W

116

Product Dimention

Installaction & User Manual

117

Installaction & User Manual

118

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents