AVAILABLE REPAIR KITS
Rotary Head Kit - Major:
P/N 2100279 (DFSCP18)
P/N 2100202 (DFSCP18GZ)
Includes items 2, 3, 4, 5, 6, 7, 8, 9,
10, 11, 12, 13, 14, 15 and 16
Rotary Head Kit - Minor:
P/N 2100203
Includes items 9, 10, 12 and 16
Complete Rotary Head Kit:
P/N 2103065 (DFSCP18)
P/N 2103000 (DFSCP18GZ)
Includes all items
6
5
7
8
10
12
9
5
14
3
14
2
14
16
11
4
6
1
17
13
15
ITEM
NO.
1
4
5
2
3
6
11
12
13
14
7
8
9
10
15
16
17
PART
NO.
2500004
2510017
2520030
2520028
2520031
2520027
2640015
2640004
2701012
2701011
2701010
2720007
2530008
2530007
2200037
2520029
2200038
2710000
2640012
DESCRIPTION
Housing, Swivel (DFSCP18)
Housing, Swivel (DFSCP18GZ)
Bearing Retainer, Small
Retainer, Bearing
Washer, Bearing Retainer
Spacer, Bearing
Bearing, 15 x 42, DFSCP18
Bearing, 15 x 42, DFSCP18GZ
O-ring
O-ring
O-ring
Spring, Compression
Pin
Stem, Small
Snap Ring
Snap Ring
Stem, Swivel
Back-up Ring
Zerk, Grease, DFSCP18GZ
Ref 300562 Rev. F
05-12
QTY.
1
1
2
1
1
2
1
3
2
1
1
1
1
1
1
1
1
PROFESSIONAL FLAT SURFACE CLEANER
FROM GENERAL PUMP
• FULL 18 Inch CLEANING PATH
• HEAVY-DUTY ANODIZED
ALUMINUM COMPONENTS
• RUGGED ABS COVER
DFSCP18
DFSCP18GZ
OPERATOR’S MANUAL
WARNING: Read Before Operating Machine
Always wear protective eyewear
Keep clear of rotating nozzles
Never lock trigger gun open with any device
Drain water in cold weather to avoid freezing
Tampering with any part of this machine will void all warranties
General Pump is a member of the
Interpump Group
8
Operating Instructions
1. Connect to Pressure Washer.
2. Turn water on and open valve. Open trigger gun for flow of water through nozzles. Nozzles must have flowing spray. If not, remove tips and clean; reassemble, making sure that groove of nozzle is parallel to spray bar. Use thread sealant when installing nozzles.
3. Start Pressure Washer. The Hammerhead is ready for operation.
4. Walk slowly behind the Hammerhead cleaning as you go. If striping occurs, slow down your pace.
5. Periodically check weep hole on bottom of swivel. Water will seep slowly; if water shoots out, stop and replace seals. Swivel assembly can be rebuilt.
6. For maximum effectiveness keep spray tips clean. If the machine vibrates, stop and clean spray tips.
7. DFSCP18GZ ONLY: Use No. 2 general purpose waterproof lithium grease. Grease swivel as needed depending on usage. Contact your dealer with questions about greasing.
DO NOT ALLOW MACHINE TO REMAIN STATIONARY
ON SOFT SURFACES SUCH AS WOOD.
Caution: Striking any raised obstacle during operation will damage machine. If contact does occur and results in vibration when operating machine, STOP and replace spray bar. Continued operation could result in serious injury or damage to machine.
Operating Pressures: 1,000 to 4,000 PSI
Max Flow: 8.0 GPM
Dimensions: 70” x 18.3” x 18.3”
Weight: 17 lbs.
General Pump
1174 Northland Drive • Mendota Heights, MN 55120
Phone: 651.686.2199 • Fax: 800.535.1745
www.generalpump.com • [email protected]
Ref 300562 Rev. F
05-12
ITEM
NO.
PART
NO.
DESCRIPTION QTY.
8
9
6
7
4
5
2
3
1
2103065 Swivel (DFSCP18)
2103000 Swivel (DFSCP18GZ)
2660119 Deck, GP
2530052 Arm, Rotary, Assy.
2630010 Plate, Retaining
2540023 Collar, Split
2200055 SHCS, M8
2200054 SHCS, M8
2540020 Block, Handle
2200047 Bolt, M6
10 2203406 Washer, M6
11 2540021 Handle, Lower
12 2540022 Handle, Upper
1
2
8
4
1
1
1
1
1
8
1
1
ITEM
NO.
PART
NO.
DESCRIPTION QTY.
13 2660047 Grip, Handle
14 2660046 Plug, Handle
15 2660049 Brush Assy.
1
16 DG4000FSC Gun, Flat Surface Cleaner 1
1
1
17 2200053 Nut, M8 x 1.25
18 D10009 Plug
19 D10004 Coupler, 3/8 x 3/8-M
20 2200026 Nut, M6, Nylok
21 2202010 Pin, 55mm, w/Ring, SST
22 2200058 HHCS
23 2200018 Washer, M6
24 2203507 Washer
25 2702026 Hose, FSC, 18”
4
1
2
2
1
1
2
4
1
