Quick Installation Guide
Version 1.0
EmCORE-i315
386SX Onboard 40MHz CPU with
4MB EDO, Ethernet, 2 serial port and DiskOnChip socket
Part Number:7003150010010
Copyright © 2002
All Rights Reserved.
The information in this document is subject to change without prior notice in order to improve the reliability, design and function. It does not represent a commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or consequen-tial damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
About this Quick Installation
This Quick Installation provides general information and installation instructions about the product. This Quick Installation is intended for experienced users and integrators with hardware knowledge of personal computers. If you are not sure about any description in this Quick Installation, please consult your vendor before further handling.
2 EmCORE-i315 Quick Installation
Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its components against damage from static electricity, you should always follow the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you want to work on the inside
2. Hold the board by the edges and try not to touch the IC chips, leads or circuitry
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came with the Single Board Computer, whenever components are separated from the system
Technical Support
If you have any technical difficulites, please consult the user's manual first at: ftp://ftp.arbor.com.tw/pub/install
Please do not hesitate to call or e-mail our customer service when you still can not find out the answer.
http://www.arbor.com.tw
E-mail:[email protected]
EmCORE-i315 Quick Installation 3
Specifications
Sysem:
• CPU + Chipset: 386SX Onboard 40MHz CPU, embedded in Ali
M6117C Chipset
• System Memory: 4MB EDO RAM standard onboard
Multi I/O:
• Serial: Two RS-232C/485 ports (COM 1/COM2)
• Parallel: Supports SPP, EPP and ECP mode
• 16-bit Digital I/O
LAN:
• Chipset: Realtek 8019AS single chip, 10Mbps, NE2000 compatible
Flash Disk:
• DiskOnChip2000 socket : supports 16MB ~ 1GB Flash Disks
Mechanical and Environmental:
• Operating Temperature: -20 to 70 ° C
• Power: Single +5V @400mA
4 EmCORE-i315 Quick Installation
Packing list
Before you begin installing your single board computer, please make sure that the following materials have been shipped:
> 1 x EmCORE-i315DL
> 1 x Quick Installation Guide
> 1 x CD driver
> 1 x Warranty Card
Ordering Codes
EmCORE-i315DL 386SX Onboard 40MHz CPU with 4MB EDO, Ethernet, 2 serial port and DiskOnChip socket
EmCORE-i315 Quick Installation 5
Board Layout Top View (Front)
J10
6 EmCORE-i315 Quick Installation
Board Layout Top View (Back)
KBD1
PWR1
J5 J4
J10
J2
EmCORE-i315 Quick Installation 7
Board Dimension
8 EmCORE-i315 Quick Installation
Jumper Quick Reference
Jumpers
Lable
J1
J4
J2
RES1
Function
Clear CMOS
RS-232& RS-485 Selection on COM1&COM2
DOC, Flash and EEPROM address selection
Reset Function
EmCORE-i315 Quick Installation 9
Connector Quick Reference
Connectors
Lable
J10
GPIO1
COM1
COM2
KBD1
LAN1
J3
LPT1
PWR1
Function
PC104 Connector
GPIO Connector
RS232 Serial Port: COM1
RS232 Serial Port: COM2
Keyboard Connector
10/100M LAN1 Connector
10/100M LAN1 Connector FOR OEM
Parallel Port
2P Power Connector
10 EmCORE-i315 Quick Installation
CMOS Jumper Settings
CMOS Operation (J1)
Type : J1: onboard 3-pin header
1 2 3
J1
If the EmCORE-i315 refuses to boot due to inappropriate CMOS settings here is how to proceed to clear (reset) the CMOS to its default values.
CMOS Setup (J1) J1 Status
Normal Operation
Clear CMOS
default setting 1-2 ON
1-2
2-3
ON
ON
DOC / Flash / EEPROM Selection
DOC, Flash and EEPROM Selection (J2)
Type : J2: onboard 2x3-pin header
1
3
5
Mode Setting (J2)
OFF
OFF
OFF
ON
OFF
1-2
ON
OFF
ON
3-4
ON
ON
OFF
OFF
ON
ON
OFF
OFF
5-6
ON
ON
ON
ON
ON
OFF
OFF
OFF
DOC D0000
DOC D8000
FLASH D0000
FLASH D8000
FLASH D4000
EPROM D0000
EPROM D8000
ALL OPEN
Deafult setting DOC D0000
2
4
6
EmCORE-i315 Quick Installation 11
Serial Port Selection (RS232C/485)
RS-232C/485 Mode select (J4)
Type : J4: onboard 6-pin(2*3) header
1
3
5
2
4
6
RS-422/485 Mode on COM1 & COM2
The onboard COM1 and COM2 port can be configured to operate in RS-485 modes. Jumper J4 switches between RS-232C or RS-485 mode. All of the
RS-232C/485 modes are available on COM1 or COM2.
COM2
Pin Defined: RS-232C RS-485
Pin1 : DCD
Pin2 : RXD
RTx+
RTx-
Pin8 : CTS
Pin9 : RI x x
J4 Selection
RS-232C
RS-485
1-3 2-4 3-5 4-6
ON
OFF
default setting RS-232C
ON
OFF
OFF OFF
J5(1-2) J5(3-4)
Reset System
Reset System (RES1)
Type: Onboard 2-pin header
Pin
1
2
Description
RST
GND
RES1
1
2
12 EmCORE-i315 Quick Installation
COM1 & COM2 Connector
7
9
3
5
2
1
Connector :
Pin
1
COM1
Type : onboard 10-pin box header
Description Pin Description
DCD1(485DATA1+) 2 RXD1(485DATA1-)
COM1
&
COM2
TXD1
GND
RTS1
RI
4
6
8
1 0
DTR1
DSR1
CTS1
NC
10
9
Connector : COM2
Type : onboard 10-pin box header
7
9
3
5
Pin
1
Description Pin Description
DCD2(485DATA2+)
TXD2
GND
RTS2
RI
2
4
6
8
1 0
RXD1(485DATA2-)
DTR2
DSR2
CTS2
NC
16-Bit General Purpose I/O
Connector : GPIO1
Type : onboard 20-pin box header
1 5
1 7
1 9
9
1 1
1 3
5
7
Pin
1
3
Description
GND
GPI0
GPI1-
GPI2
GPI3
GPI4
GPI5
GPI6
GPI7
VCC
1 6
1 8
2 0
1 0
1 2
1 4
6
8
Pin
2
4
Description
VCC
GPO0
GPO1
GPO2
GPO3
GPO4
GPO5
GPO6
GPO7
GND
2
1
GPIO1
EmCORE-i315 Quick Installation
20
19
13
Keyboard Connector
Connector : KBD1
Type : onboard waver 5-pin
Pin
1
3
5
Description
KB_CLK
N/A
Vcc
Pin
2
4
Description
KB_DATA
GND
1 2 3 4 5
Fast Ethernet Connectors
LAN Port (10/100Mbps)
Connector : LAN1
Type : external RJ-45 on bracket
Pin
Desciption
1
TX+
2
TX-
3
RX+
4
NC
5
NC
LAN 1
6
RX-
7
NC
1
2
3
4
7
8
5
6
8
NC
Connector : LAN1 (OEM)
Type : Onboard 2x4 pin connector
Pin
Desciption
Pin
Description
1
TCT
5
RX-
2
TX-
6
NC
3
RX+
7
NC
4
NC
8
NC
2 4 6 8
1 3 5 7
14 EmCORE-i315 Quick Installation
LPT1
19
8
9
1 0
5
6
7
1 1
1 2
1 3
2
3
4
Pin
1
Type : Onboard 20-pin header
Description
STROBE
PTD0
PTD1
PTD2
PTD3
PTD4
PTD5
PTD6
PTD7
ACK
BUSY
PE
SELECT
2 1
2 2
2 3
1 8
1 9
2 0
2 4
2 5
2 6
Pin
1 4
1 5
1 6
1 7
GND
GND
GND
GND
GND
GND
Description
AFD
ERROR
INIT
SLIN
GND
GND
GND
20
Power Connector
Connector:PWR1
Type : onboard 2-pin Wafer connector
Pin
1
2
Description
GND
Vcc
1
2
PWR2
1
2
EmCORE-i315 Quick Installation 15
