ICP VEX-142i Quick Start Guide
Advertisement
Advertisement
for VXC-112(i)AU/142(i)AU/182iAU
VEX-112(i)/142(i)
English/ Mar 2011/ Version 1.2
What’s in the shipping package?
The package includes the following items:
VXC/VEX Series
Card
Software CD
(
V4.8 or later
)
COM Port Mapping
Quick Start Guide
(This Document)
Setting SW1 dip-switch (COM Selector) to 0x05 (1 and 3 “NO”, others “OFF”). The setting forces the VXC/VEX card to use COM5 and COM6.
VXC-112(i)AU/142(i)AU/182iAU, VEX-112(i)/142(i) Quick Start Guide
1
SW1 Setting Table:
SW1 DIP Switch 8 7 6 5 4 3 2 1
Board ID=0x00 (Default)
COM = Auto-defined
Board ID=0x03
COM = 3/4
Board ID=0x05
COM = 5/6
Board ID=0x07
COM = 7/8
Board ID=0x09
COM = 9/10
Board ID=0x14
COM = 20/21
Board ID=0x1E
COM = 30/31
Board ID=0x28
COM = 40/41
Board ID=0x32
COM = 50/51
Board ID=0x3C
COM = 60/61
Board ID=0x64
COM = 100/101
Board ID=0x96
COM = 150/151
Board ID=0xC8
COM = 200/201
.
.
.
Board ID=0xFF
COM = 255/256
OFF OFF OFF OFF OFF OFF OFF OFF
OFF OFF OFF OFF OFF OFF
OFF OFF OFF OFF OFF
OFF OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF
ON
OFF OFF
ON
OFF
ON ON
OFF
ON ON
OFF OFF
ON
OFF OFF OFF
.
.
.
ON
.
.
.
ON
.
.
.
ON
ON
OFF OFF
ON
OFF OFF
.
.
.
.
.
.
ON
ON
.
.
.
ON ON
OFF
ON ON ON
ON
OFF
ON
OFF OFF
ON ON ON ON
OFF
ON
OFF
ON
OFF OFF OFF
ON ON
OFF OFF
ON
OFF
ON ON ON ON
OFF OFF
OFF
.
.
.
OFF
.
.
.
ON ON ON ON ON ON ON ON
VXC-112(i)AU/142(i)AU/182iAU, VEX-112(i)/142(i) Quick Start Guide
2
Installing Windows Driver
1.
Launch the Windows 2000/XP/2003/2008/Vista/7 (32/64 bit) driver setup program. It is located at :
CD: \Napdos\multiport\windows\VxCard_W7_Vx.xx.xx.exe http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/multiport/windows/
2.
Click the
“Next>”
button to start the installation.
3.
Click the
“Next>”
button to install the driver into the default folder.
4.
Check the
“Create a desktop icon”
and click the
“Next>”
button.
5.
Select the
“NO, I will restart the computer later”
and click the
“Finish”
button.
For installing driver on other systems, please refer to: http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/multiport/man ual/
Installing the Hardware
Follow these steps:
1.
Shut down and power off your computer.
2.
Remove the cover from the computer.
3.
Select an unused PCI/PCI Express slot.
4.
Carefully insert your VXC/VEX card into the PCI/PCI Express slot.
5.
Replace the PC cover.
6.
Power on the computer.
7.
Follow the prompt message to finish the Plug&Play steps.
8.
Make sure the com ports installed are correct as follows: i.
Select “Start Æ Control Panel” and then double click the “system” icon. ii.
Click the “Hardware” tab and then click the “Device Manager” button. iii.
Check the COM ports of VXC/VEX card which listed correctly or not.
VXC-112(i)AU/142(i)AU/182iAU, VEX-112(i)/142(i) Quick Start Guide
3
Pin Assignments and Cable Wiring
RS-422 Cable Wiring
(VXC-142(i)AU, VXC-182iAU and VEX-142(i) CN1)
RS-485 Cable Wiring
VXC Card
PIN
CN1
Signal
1 TxD-
2 TxD+
3 RxD+
4 RxD-
5 GND
6 RTS-
7 RTS+
8 CTS+
9 CTS-
Device
PIN Signal
4 RXD-
3 RxD+
2 TxD+
1 TxD-
5 GND
9 CTS-
8 CTS+
7 RTS+
6 RTS-
(VXC-142(i)AU, VXC-182iAU and VEX-142(i) CN1)
VXC Card
CN1
PIN Signal
1 DATA-
2 DATA+
Device
PIN Signal
1 DATA-
2 DATA+
The RS-485 bus is a differential (balanced) signal, thus you cannot wire the
Data+ with Data- directly for a single port loop-back test. It will not work at all!
VXC-112(i)AU/142(i)AU/182iAU, VEX-112(i)/142(i) Quick Start Guide
4
RS-232 Cable Wiring
(VXC-112(i)AU, VXC-182iAU and VEX-112(i) CN2)
System
1
PIN
RxD 2
TxD 3
GND 5
DTR 4
--
3 TxD
2 RxD
5 GND
6 DSR
DCD 1 --
DSR 6
RTS 7
4 DTR
8 CTS
CTS 8
RI 9
7 RTS
9 RI
Self Test
1.
Use the DN-09-2(optional) to connect the
VXC-112(i)AU/142(i)AU/182iAU or VEX-112(i)/142(i).
VXC-112(i)AU/142(i)AU/182iAU, VEX-112(i)/142(i) Quick Start Guide
5
2.
Wire Port-1 and Port-2 :
VXC-112(i)AU/VEX-112(i) (RS-232)
Pin
Assignment
CN2 TxD
CN2 RxD
Pin
No.
3
2
Pin
No.
Pin
Assignment
VXC-142(i)AU/VEX-142(i) (RS-422/485)
Pin
Assignment
CN2 DATA-
CN2 DATA+
Pin
No.
1
2
Pin
No.
Pin
Assignment
VXC-112(i)AU/142(i)AU/182iAU, VEX-112(i)/142(i) Quick Start Guide
6
VXC-182iAU(RS-232 and RS-422/485)
3.
Execute the Test2COM.exe program.
Get the file from:
CD:\Napdos\multiport\utility http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/multiport/utility/
VXC-112(i)AU/142(i)AU/182iAU, VEX-112(i)/142(i) Quick Start Guide
7
4.
Test Success.
Related Information
VXC Card Product page: http://www.icpdas.com/products/Industrial/multi_serial/multi_introductions.htm
DN-09-2,CA-0915 and CA-0910-F product page (optional): http://www.icpdas.com/products/DAQ/screw_terminal/dn_09_2.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
i-7520 product page (optional): http://www.icpdas.com/products/Remote_IO/i-7000/i-7520.htm
Documentation:
CD: \Napdos\multiport\manual\ http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/multiport/manual/
Software :
CD: \Napdos\multiport\ http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/multiport/
ICP DAS Web Site: http://www.icpdas.com
Contact Us (E-Mail): [email protected]
Copyright @ 2011 by ICP DAS Co., Ltd. All Rights Reserved.
8

Public link updated
The public link to your chat has been updated.
Advertisement