CE™: .
HE™: .
1 Fl CAT6
cat Gui
1 3 or Suppl or EI Mi 30’ o
1 2 br BR
1 Power
1 ed
Power y
Power Cont ol Audi mpor ant aci t of Ci QuadCam, t act ce t ze SCT’
RCf o vent l on.
H001 [2]
RC8-CQC Installation Instructions
Supporting the Cisco Quad Camera and
Cisco SX80, Plus & Pro Codecs
TEST YOUR LINK CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your LINK cable’s wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1. Test and verify your CAT6 STP or FUTP LINK cable for UTP 568A/568B. Link cable must be between 30ft - 300ft.
The LINK cable between the RC8-CE module (transmitter) & RC8-HE module (receiver) must always be a single, point-to-point CAT cable with no couplers or interconnections.
2. Connect the provided PowerSniffer to the Quad Camera end of your CAT6 STP or FUTP LINK cable.
3. Connect the other end of the LINK cable to the blue “SCTLink™” connection on the Head End module.
4. Connect the WPS-48 power supply to the Head End module.
5. Connect the WPS-48 power supply to AC mains.
6. If the “SCTLink™” cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable .
7. Once your cable has been tested, please disconnect the WPS-48 power supply from the RC8-HE module, and the PowerSniffer from the LINK cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1. Connect the RCC-C014 HDMI cables between the Quad
Camera’s HDMI 1 & 2 connectors RC8-CE’s “HDMI 1” and
“HDMI 2” ports.
2. Connect the RCC-C015 UTP cable between the Quad
Camera’s RJ45 Ethernet port and the RC8-CE’s Ethernet port.
3. Connect the PPC-018 power cable between the Quad
Camera’s power connector and the RC8-CE’s “12VDC
Output” port.
Connect the codec-end cables: corresponding “HDMI Out 1 A” and “HDMI Out 2 A” port.
5. Connect the 3ft RCC-H016 UTP control cable between the codec’s RJ45 camera Ethernet port and the RC8-
HE’s “Ethernet 1”.
Connect and Initiate the Extended System:
6. Connect one end of your CAT6 STP or FUTP LINK cable to the RC8-HE module’s blue “SCTLink™” port.
7. Connect the other end of the CAT6 STP or FUTP LINK cable to the RC8-CE module’s blue “SCTLink™” port.
8. Connect the WPS-48 power supply to the RC8-HE.
4. Connect two 3 ft RCC-H001 HDMI cables between the codec’s HDMI camera inputs and the RC8-HE’s
RC8-CE
RC8-HE
• ALLOW UP TO TWO MINUTES FOR THE QUAD CAMERA SYSTEM TO INITIALIZE •
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
OK LED 1 & 2
OK LED 1 & 2
INACTIVE
Blinking Green (~1 second interval)
Blinking Green (~1 second interval)
Blinking or Solid Red
Blinking or Solid Red
& Blinking
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC8-CQC™.
This kit is also inclusive of [1] RC-RKL Rack Shelf .
DESCRIPTION
[2] RCC-C014 1’ HDMI Cables
RCC-C015 1’ UTP Cable
Video connection between Quad Camera and RC8-CE module.
Control connection (Ethernet) between Quad Camera and RC8-CE module.
PPC-018 1’ Power Cable
[2] RCC-H001 3’ HDMI Cables
RCC-H016 3’ UTP Cable
Power connection between Quad Camera and RC8-CE module.
Video connection between the codec and RC8-HE module.
Control connection (Ethernet) between the codec and RC8-HE module.
Power Supply Specifications (AC-Mains Side): Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 48VDC power supply uses 2.80 amperes AC maximum. All specifications subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • © SOUND CONTROL TECHNOLOGIES, INC
