GE ZIF360NHLH Monogram 36" Built-In All Freezer Quick Specs

Add to My manuals
17 Pages

advertisement

GE ZIF360NHLH Monogram 36

MONOGRAM 36" BUILT-IN ALL-FREEZER

SECTION 1

STANDARD INSTALLATION

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

ZIF360NHLH

SECTION 2

FLUSH INSET INSTALLATION

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

OVERALL DIMENSIONS

36"

(91.5)

ZIF360NHLH

STANDARD INSTALLATION

25 1/8"

(63.8)

23 7/8"

(60.7)

1 7/8"

(4.8)

*84"

(213.4)

*83 1/2"

( 212.1)

69 5/8"

(176.8)

*73 1/4"

(186.1)

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

Shipping Weight

36" (91.4 cm)

84" (213.4 cm)

25 3/8" (64.45 cm)

36 3/4" (93.4 cm)

35 1/2" (90.2 cm)

83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

24" (61 cm)

1/4" OD copper tubing or GE

SmartConnect kit

569 lb

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

*3"

(7.6)

FRONT VIEW

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

*3 1/4"

(8.3)

35"

(89.0)

Case width

SIDE VIEW

** Allow

25"

(63.5) min

clearance for 130˚

door swing

TOP VIEW

36 3/4"

(93.4)

** Allow

4"

(10.2) min

clearance to a wall

for 90˚ door swing

**These units are equipped with a 3-position door stop. The factory set 130° door swing can

be adjusted to 90° or 130° for standard installation if clearance to adjacent cabinets or

walls is restricted. Allow 15" minimum clearance to wall for pan removal. If the 90˚ door

stop position is used, pan access is maintained but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances.

ZIF360NXLH

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

STANDARD INSTALLATION

2 5/16"

(5.9) 2 5/16"

(5.9)

35 1/2"

(90.2)

35 1/2"

(90.2)

5 1/2"

5 1/2"

(14.0)

*83 1/2" min

*84 1/2" max

*Trim will overlap additional 7/16" additional 7/16"

9"

(22.9)

A

(191.8)

From floor to bottom to bottom area area

5"

(12.7)

WATER

B

3 1/2"

(9.0)

3 1/2" 5"

(12.7)

3 1/8"

(7.9)

25 3/8"

(64.5)

25 3/8"

(64.5)

7/16"

(1.1)

7/16"

(1.1)

Trim overlap

W

W

3 1/2"

(8.9)

ANTI-TIP BRACKET

81 1/2"

(207.0)

Use two additional hole locations at end of brackets

Bracket mounted into vertical wall studs centered within the cutout selected are centered on

Wall

Studs

Wall

Studs

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

ZIF360NHLH

STANDARD

INSTALLATION

NOTES

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:

The freezer is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

The information below applies to all installation constructions:

• A wall bracket, bolts and toggles will be supplied with the unit.

• The bolts will be used to attach bracket to wall in 4 locations.

Two of the locations must penetrate the center of the wall studs.

• The toggles are used for stability in drywall and when metal studs are encountered.

Lag bolts are used in wood studs.

• In installation opening, measure

81 1/2" from floor and draw a horizontal line.

• Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center

32 1/2" of installation opening to ensure 2 wall studs are penetrated.

• The bracket will be centered left to right in opening with bottom of bracket on the horizontal line.

• When unit is placed in opening, the bracket tabs will align with openings in back of the unit.

The unit will be secured to the bracket using supplied “L” bolts.

See Installation Instructions for detailed instructions.

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER ZIF360NHLH

STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION

A

Grille Panel

Door

Panel

B

C

Trim

1/4" Framed Panel

Door

Supplied Handles

STANDARD

INSTALLATION

NOTES

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.

1/4" Framed Panels: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 11 lbs.

A B C

1/4" Framed Panel 33 7/8" 8 7/8" 69 5/16"

STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE

INSTALLATION

A

Grille Panel B

Trim

1/4" Backer Panel

.10" Spacer Panel

Door

3/4" Overlay Panel

Supplied Handles

Door

Panel

C

A B C

1/4" Backer Panel 33 7/8" 8 7/8" 69 5/16"

.10" Spacer Panel 32 1/2" 7 5/8" 67 15/16"

3/4" Overlay Panel 34 1/8" 9" 69 9/16"

3/4" Overlay Panels: For 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.

Center each panel over the other.

Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 11 lbs.

Door Handles:

The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.

ZKHPSS1: Professional stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle-

30 1/2" long.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle - 64 1/4" long.

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

CUSTOM SIDE PANELS

F

24"

(61.0)

3/16"

(.5)

*84"

(213.4)

*Depending on installation height

*3"- 4"

(7.6 - 10.2)

*Depending on installation height

ZIF360NHLH

STANDARD

INSTALLATION

NOTES

F Side panels must be used whenever the sides of the freezer will be exposed. A 1/4" side panel will slip into the side case trim. Secure the panels to the freezer with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH

ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

DUAL INSTALLATIONS

A

4 5/16"

(11.0)

71 1/2"

(181.7)

Finished Width

ELEC.

9"

(22.9)

ELEC.

9"

(22.9)

24 3/16"

(61.4)

83 1/2" min

84 1/2" max

(212.1-214.6)

*Trim will overlap additional 7/16"

75 1/2"

(191.8 )

From floor to bottom of electrical area

26 3/16"

(66.5)

Min. Cutout Depth

ZIF360NHLH

STANDARD

INSTALLATION

NOTES

A A separate 115V, 60Hz, 15- or

20-amp power supply is recommended for each product.

Additional cutout width may be required when side panels are used.

WATER

3 1/2"

WATER

3 1/2"

25"

(63.5) min

To wall

1"

(2.5)

FRONT VIEW

25"

(63.5)

To wall min

W

2" min

(5.1)

SIDE VIEW

15"

(38.1) min

To wall

STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION

A

PANEL DIMENSIONS

130˚

Door swing

D

Grille Panel

130˚

Door swing

D

B

5"

(12.7) min

1/4"

Framed

Panel

A 69 7/8"

B 8 7/8"

C 69 5/16"

D 33 7/8"

Door

Panel

Door

Panel

C

Trimmed freezers are designed to be customized with decorative panels.

Field-installed custom door and grille panels are required.

1/4" Framed Panels:

For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 25 lbs

Order ZUG2: Unified grille kit for one continuous panel in dual installation.

Maximum total door panel weight -

25 lbs.

PANEL ASSEMBLY

CROSS SECTION

Trim

Door

1/4" Framed Panel

Supplied Handles

ZIF360NHLH_ZIF360NHRH _ZIFP360NHLH_ZIFP360NHRH_ ZIFS360NHLH_ZIFS360NHRH

ZIR360NHLH_ZIR360NHRH_ZIRP360NHLH_ZIRP360NHRH_ZIRS360NHLH_ZIRS360NHRH

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER ZIF360NHLH

STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION

D

ELEC.

Door

Panel

A

Grille Panel

D

71 1/2"

(181.6)

Finished Width

ELEC.

Door

Panel

B

24 3/16"

(61.4)

C

PANEL DIMENSIONS

1/4"

Backer

Panel

.10"

Spacer

Panel

3/4"

Overlay

Panel

A 69 7/8" 68 1/2" 70 1/8"

B 8 7/8" 7 5/8" 9"

C 69 5/16" 67 15/16" 69 9/16"

Min. Cutout Depth

D 33 7/8" 32 1/2" 34 1/8"

.25" + .10" + .75" =

1.10" Total Panel Thickness

PANEL ASSEMBLY

CROSS SECTION

Trim

1/4" Backer Panel

WATER

25"

(63.5)

To wall min

130˚

Door swing

1"

(2.5)

A

130˚

Door swing

25"

(63.5) min

To wall

5"

(12.7) min

C

75 1/2"

Door

3/4" Overlay Panel

Supplied Handles

W

2" min

(5.1)

SIDE VIEW

15" min

B

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH

ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH

STANDARD

INSTALLATION

NOTES

3/4" Overlay Panels: For 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.

Center each panel over the other.

Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 25 lbs.

Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.

Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.

ZKHPSS1: Professional stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle -

30 1/2" long.

ZKHSS2: European stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle -

64 1/4" long.

A In a side-by-side installation of a leftand-right-hand door swing product,

1" clearance between the units is required.

Order ZUG2: Custom panel unified grille kit for one continuous grille panel.

B In a side-by-side installation with same door swing, allow 2" minimum clearance between the products to prevent the door swing interference.

Allow 15" minimum to a wall to achieve full drawer extension and pan removal. Additional clearances are required when using custom panels and handles.

NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation.

C In a side-by-side installation with right and left door hinges together, allow 5” minimum clearance between the two products to prevent one door from striking the other.

Additional clearances required when using custom panels and handles.

NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation.

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER ZIF360NHLH

OVERALL DIMENSIONS

FLUSH INSET INSTALLATION

38"

(96.5)

26 1/8"

(66.3)

20 5/8"

(52.4)

10 15/16"

(27.8)

*84 11/16"

(215.1)

69 3/4"

(177.2)

*73 3/4"

(187.3)

* 84"

( 213.4)

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

Shipping Weight

38" (96.5 cm)†

84 11/16" (215.1 cm)†

26 1/8" (66.3 cm)†

38 3/4" (98.4 cm)

39" (99.1 cm)

85" (215.9 cm)

26 3/16" (66.5 cm)

1/4" OD copper tubing or GE

SmartConnect kit

570 lb (258.5 kg)

† Dimensions include 3/4" custom cabinet panel

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

FRONT VIEW

*4"

(10.2)

* Shipping height. Use leveling legs and wheels for maximum 1" height

adjustment from shipping height. Nominal installation height is 84 11/16".

SIDE VIEW

35"

(89.0)

Case width

Allow

15"

(38.1) min clearance for 115˚ door swing

TOP VIEW

38 3/4"

(98.4)

Allow

4"

(10.2) min clearance to a wall for 90˚ door swing

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

MONOGRAM 36" BUILT-IN ALL-FREEZER

FLUSH INSET INSTALLATION 3/4" PANELS

35 1/2"

(90.2)

26 3/16"

(66.5)

ELEC.

20 15/16"

(53.2)

C

*Trim will overlap additional 7/16"

85"

(215.9)

Finished cleats

SIDE VIEW

W

5 1/4"

(13.3)

TOP VIEW

Case

Finished cleats

Case Trim

24"

(61.0)

3/4" Panel

3/4"

(1.9)

Width of side cleats

39"

(99.1) Flush inset width

37 1/2"

(95.3)

Width between cleats

ELEC.

9"

(22.9)

5 1/2"

(14.0)

24 3/16"

(61.4)

75"

7/16"

(1.1)

1/2"

(1.3)

85"

(215.9)

75 1/2"

(191.8 )

From floor of electrical area

B 10"

(25.4)

7"

(17.8)

WATER

3 1/2"

(9.0)

7"

(17.8)

SIDE VIEW

3 1/2"

(8.9)

FRONT VIEW

ANTI-TIP BRACKET

Use two additional hole locations at end of brackets

FLUSH INSTALLATION

ZIF360NHLH_RH

ZIR360NHLH_RH

Bracket mounted into vertical wall studs centered within the cutout

Ensure holes selected are centered on the studs

Wall

Studs

ZIF360NHLH

FLUSH INSET

INSTALLATION

NOTES

NOTES

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

C Top cleat should be 1" thick

WARNING:

The freezer is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

The information below applies to all installation constructions:

• A wall bracket, bolts and toggles will be supplied with the unit.

• The bolts will be used to attach bracket to wall in 4 locations.

Two of the locations must penetrate the center of the wall studs.

• The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.

• In installation opening, measure

81 1/2" from floor and draw a horizontal line.

• Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32 1/2" of installation opening to ensure 2 wall studs are penetrated.

• The bracket will be centered left to right in opening with bottom of bracket on the horizontal line.

• When unit is placed in opening, the bracket tabs will align with openings in back of the unit.

The unit will be secured to the bracket using supplied “L” bolts.

See Installation Instructions for detailed instructions.

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

ZIC360NXRH

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION

A

Grille Panel B

PANEL DIMENSIONS

A

38"

B C

10 7/16" 69 3/4"

Door

Panel

C

3/4" GRILLE DOOR PANEL ROUTING

DETAIL TOP

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

1-7/16"

Back

Back

TOP

Front

ZIF360NHLH

FLUSH INSET

INSTALLATION

NOTES

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door and grille trims.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 11 lbs

Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of

4" wide.

Door Handles

Custom handles are required for flush installation.

ZKHPSS1: Professional stainless steel handle designed to fit 3/4" custom panels. Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle – 64 1/4" long.

Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.

1/8"

DETAIL BOTTOM

DETAIL

LEFT SIDE

ROUTER DEPTH 1/4"

2-1/16"

LEFT

SIDE

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL RIGHT

SIDE

ROUTER DEPTH 1/4"

3/32"

1/4"

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

2-1/16"

Front

RIGHT

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

3/4" RAISED DOOR PANEL ROUTING

11/32"

1/4"

DETAIL TOP

3/4"

1/4" 7/16"

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

1/4"

LEFT

SIDE

DETAIL BOTTOM

DETAIL

LEFT SIDE

ROUTER DEPTH 1/4"

2-1/16"

Back

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Front

DETAIL RIGHT

SIDE

ROUTER DEPTH 1/4"

3/32"

1/4"

2-1/16"

Back

RIGHT

SIDE

TOP

Front

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

ZIF360NHLH

FLUSH INSET

INSTALLATION

NOTES

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door and grille trims.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 11 lbs

Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of

4" wide.

Door Handles

Custom handles are required for flush installation.

ZKHPSS1: Professional stainless steel handle designed to fit 3/4" custom panels. Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle – 64 1/4" long.

Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

FLUSH INSET INSTALLATION 1/2" PANELS

35 1/2"

(90.2)

26 3/16"

(66.5)

ELEC.

20 13/16"

(52.9)

*Trim will overlap additional 7/16"

C

5 3/8"

(13.7)

TOP VIEW

Case

Finished cleats

Case Trim

24"

(61.0)

1/2" Panel

3/4"

(1.9)

Width of side cleats

39"

(99.1) Flush inset width

37 1/2"

(95.3)

Width between cleats

ELEC.

9"

(22.9)

5 1/2"

(14.0)

24 3/16"

(61.4)

75"

7/16"

(1.1)

1/2"

(1.3)

A

Finished cleats

85"

(215.9)

85"

(215.9)

75 1/2"

From floor to bottom of electrical area

SIDE VIEW

W

7"

(17.8)

B

10"

(25.4)

3 1/2"

(9.0)

7"

(17.8)

SIDE VIEW

3 1/2"

(8.9)

FRONT VIEW

ANTI-TIP BRACKET

Use two additional hole locations at end of brackets

FLUSH INSTALLATION

???? ZIF360NHLH_RH

???? ZIR360NHLH_RH

Bracket mounted into vertical wall studs centered within the cutout

Ensure holes selected are centered on the studs

Wall

Studs

ZIF360NHLH

FLUSH INSET

INSTALLATION

NOTES NOTES

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

C Top cleat should be 1" thick

WARNING:

The freezer is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

The information below applies to all installation constructions:

• A wall bracket, bolts and toggles will be supplied with the unit.

• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs.

• The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.

• In installation opening, measure

81 1/2" from floor and draw a horizontal line.

• Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32 1/2" of installation opening to ensure 2 wall studs are penetrated.

• The bracket will be centered left to right in opening with bottom of bracket on the horizontal line.

• When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts.

See Installation Instructions for detailed instructions.

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

ZIC360NXRH

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

FLUSH INSET 1/2" PANEL DIMENSIONS SINGLE INSTALLATION

A

PANEL DIMENSIONS

Grille Panel B

A B C

1/4" Backer Panel 33 7/8" 8 7/8" 69 5/16"

.10" Space Panel 32 1/2" 7 5/8" 67 15/16"

1/2" Overlay Panel 38" 10 7/16" 69 3/4"

Door

Panel

C

ZIF360NHLH

FLUSH INSET

INSTALLATION

NOTES

The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.

• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel

Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight – 25 lbs.

Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of

4" wide.

1/2" OUTER PANEL TO BACKER PLACEMENT

C

Hinge Side

Door

1/2"

Overlay

Panel

Door Panel Back

Backer with

Overlay Panel

Assembly

1/4"

Backer

Panel

.10"

Spacer

A

D

B

PANEL DIMENSIONS

A B C

Door Panel 2 1/16" 2 1/16" 3/16"

Grille Panel 2 1/16" 2 1/16" 1 7/16"

D

1/4"

1/8"

A

C

Grille Back

D

B

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER ZIF360NHLH

DUAL INSTALLATIONS

A

4 5/16"

(10.9)

ELEC.

9"

(22.9)

5 1/2"

(13.9)

75"

(190.5)

Finished Width

ELEC.

9"

(22.9)

24 3/16"

(61.4)

5 1/2"

(13.9)

85"

(215.9)

Finished

Opening

PANEL DIMENSIONS

A B C D

1/4" Backer Panel 69 7/8" 8 7/8" 69 5/16" 33 7/8"

.10" Space Panel 68 1/2" 7 5/8" 67 15/16" 32 1/2"

1/2" Overlay Panel 74" 10 7/16" 69 3/4" 36 7/8"

75 1/2"

(191.8 )

From floor to bottom of electrical area

26 3/16"

(66.5)

Min. Cutout Depth

7"

(17.8)

3 1/2"

(9.0) 7 1/2"

(19.1)

7 1/2"

(19.1)

3 1/2"

(9.0) 7"

(17.8)

3 1/2"

(8.9)

FRONT VIEW SIDE VIEW

FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION

15"

(38.1) min

To wall

1 1/2"

(3.8)

A

15"

(38.1) min

To wall

W

3 1/2"

(8.9)

Grille Panel B

D

Door

Panel

D

Door

Panel

C

FLUSH INSET

INSTALLATION

NOTES

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required.

For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs.

Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

Maximum total panel weight:

• Fresh food door panels – 67 lbs.

• Grille panel – 25 lbs

Door Handles:

Custom handles are required for flush installation.

ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30 1/2" long. Order 2 kits from your Monogram supplier.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle –

64 1/4" long.

Order ZUG2: Unified grille kit for one continuous panel in dual installation.

Maximum total door panel weight -

25 lbs.

The 1/2" overlay panel must be secured to a .10" spacer panel and a

1/4" thick backer panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.

• Refer to the single unit flush installation diagram on pg 7 for backer to 1/2" overlay panel placement.

A A Separate 115V, 60Hz,

15 or 20 amp power supply is recommended for each product.

ZIF360NHLH_ZIR360NHRH

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION

A

Grille Panel B

PANEL DIMENSIONS

A B C D

74" 10 7/16" 69 3/4" 36 7/8"

D D

Door

Panel

Door

Panel

C

3/4" RAISED DOOR PANEL ROUTING - (SEE PAGE 4 FOR

3/4" GRILLE PANEL ROUTING DIAGRAMS)

DETAIL TOP

11/32"

1/4"

3/4" NOTE: Routed areas should be finished as they may be visible when assembled.

1/4" 7/16" Front

TOP

ZIF360NHLH

FLUSH INSET

INSTALLATION

NOTES

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required.

For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs.

Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

Maximum total panel weight:

• Fresh food door panels – 67 lbs.

• Grille panel – 25 lbs.

Door Handles:

Custom handles are required for flush installation.

ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30 1/2" long. Order

2 kits from your Monogram supplier.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle –

64 1/4" long.

Order ZUG2: Unified grille kit for one continuous panel in dual installation.

Maximum total door panel weight -

25 lbs.

Back

Back Front

3/16"

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL BOTTOM

DETAIL HINGE

SIDE

ROUTER DEPTH 1/4"

2 1/16"

Front

HINGE

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

3/16"

DETAIL HANDLE

SIDE

HANDLE

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

DUAL PRODUCT CLEARANCES

16 1/2" min

(41.9)

To wall

1/2"

(1.3)

16 1/2" min

(41.9)

To wall

ZIF360NHLH

FLUSH INSET

INSTALLATION

NOTES

A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is achieved naturally when installing trim-to-trim.

A

ZIF360NHLH

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN ALL-FREEZER

FEATURES AND BENEFITS

CUSTOM PANEL MODEL

Can be personalized with cabinet-matching panels and handles

FLUSH INSET INSTALLATION

Allows the freezer to be installed flush with adjacent cabinetry

ENHANCED TEMPERATURE MANAGEMENT SYSTEM

With precise electronic controls and thermistors, maintains ideal storage conditions for frozen foods

CONCEALED ICE DRAWER

Provides quick and easy access to filtered ice

GE WATER™ FILTRATION SYSTEM

Provides clean, fresh-tasting water to the freezer's icemaker

ADJUSTABLE, WIRE SHELVES, GALLON-SIZE DOOR

BINS AND PULLOUT BASKETS

Allow customizable storage for foods and containers of varying sizes

CONCEALED HALOGEN LIGHTING SYSTEM

Illuminates contents without compromising space

ZIF360NHLH

R

Product Specification Revised 1/18

advertisement

Related manuals

Download PDF

advertisement