GE GFD40GSCMWW 7.0 Cu. Ft. capacity Dura Drum gas dryer Installation instructions


Add to my manuals
4 Pages

advertisement

GE GFD40GSCMWW 7.0 Cu. Ft. capacity Dura Drum gas dryer Installation instructions | Manualzz

GFD40GSCMWW

GE ® 7.0 Cu. Ft. Capacity Frontload Dryer

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

GAS DRYER RATING

120V 60Hz, 6A

EXHAUST OPTIONS: 3-way via rear, left, and bottom.

CIRCUIT REQUIREMENTS: An individual, properly grounded branch circuit, protected by a

15-20 amp circuit breaker or a time-delay fuse, is required.

NOTE: Dryer wall outlet must be located within

36" of service cord entry and accessible when dryer is mounted in position.

INSTALLATION INFORMATION: For complete information, see installation instructions packed with your dryer.

27" 32 1/5"

39 3/10"

5 3/8"

4 3/8"

For answers to your Monogram, GE Café ™ Series, GE Profile ™ Series or

GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.

Specification Revised 3/18

GFD40GSCMWW

GE ® 7.0 Cu. Ft. Capacity Frontload Dryer

SPECIAL INSTALLATION REQUIREMENTS

STACKED INSTALLATION:

Brackets for stacking dryer over washer are not included with the washer. Order part no. GEFLSTACK or part no. WE25X10018.

ALCOVE OR CLOSET INSTALLATION:

If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

The dryer MUST be exhausted to the outside.

Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" either side, 1" top, front and rear.

Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".

Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

BATHROOM OR BEDROOM INSTALLATION:

The dryer MUST be exhausted to the outdoors.

The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas

Code, ANSI Z223 for gas dryers.

MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET

INSTALLATIONS:

Minimum clearances to combustible surfaces 0" both sides, 3" rear.

FOR MORE INFORMATION ON VENTING KITS AND

ACCESSORIES,

PLEASE CALL 1-800-GE-CARES.

STACKED DIMENSIONS (IN INCHES)

24-7/8

3-1/2

50-5/8

3

39-3/8

PEDESTAL DIMENSIONS

(IN INCHES)

SBSD137HWW - WHITE

This optional 13" pedestal raises the door opening and height of the washer or dryer.

Feet on 13" pedestal allow it to adjust to 13-3/8" height.

13"

27"

79-5/8"

28-3/4"

For answers to your Monogram, GE Café ™ Series, GE Profile ™ Series or

GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.

Specification Revised 3/18

GE Dryer Vent

GE Dryer Vent

GFD40GSCMWW

GE ® 7.0 Cu. Ft. Capacity Frontload Dryer

DRYER EXHAUSTING INFORMATION – METAL DUCT ONLY

For complete information, see installation instructions packed with your dryer.

DUCTING MATERIALS: For best performance, this dryer should be vented with 4” diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foiltype) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

EXHAUST LENGTH CALCULATION:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.

2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.

A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow.

A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE

CALL 1-800-GE-CARES.

A

A

A

4

4

B

B

Domestic dryer models

2-1/2

2-1/2

7.0 cu. ft.

capacity models electric dryers

Best performance

Maximum length of 4" dia. rigid metal duct

Exhaust hood type

Number of

90° turns

0

1

2

3

4

A

4" opening

90 ft.

60 ft.

45 ft.

35 ft.

25 ft.

B

2-1/2" opening

60 ft.

45 ft.

35 ft.

25 ft.

15 ft.

2-1/2

3-1/2

12

1-3/4

Gas Pipe

Connection

Electrical

Connection

Specification Revised 3/18

GFD40GSCMWW

GE ® 7.0 Cu. Ft. Capacity Frontload Dryer

FEATURES AND BENEFITS

Dura Drum interior – Provides long-lasting dependability

HE Sensor Dry with dual thermistors – Continually monitors moisture and temperature to prevent clothing wear and tear due to over-drying and inconsistent heat

Speed dry – Quickly dries items and small loads for families on the go eDry™ option – Energy-saving option reduces dry temperatures on select cycles without sacrificing performance

4 heat selections – Provide the right temperatures for your clothes-drying needs

6 dry cycles – Additional cycles for your clothes drying needs

ENERGY STAR ® qualified – Meets or exceeds federal guidelines for energy efficiency for year-round energy and money savings

Model GFD40GSCMWW – White

ADA

COMPLIANT

Delicates

Bulky

Bedding

Cottons

Mixed Loads

Towels

Sheets

Steam

Full Loads

Warm

Up

Perm Press

Casuals

Quick Dry

Air Fluff

No Heat

Add

Time

Drying Damp Cool Down Complete

Estimated Time Remaining

Control Clean Filter

High

Medium

Low

Extra Low

Temp

More Dry

Dry

Less Dry

Damp

Level

Ext Tumble

Wrinkle Care

Volume Lock Controls

Hold 3 Sec

GFD45ESSKWW GFD45GSSKWW

GFD45ESPKDG GFD45GSPKDG

Specification Revised 3/18

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement