GE GTD75GCSLWS 7.4 cu. ft. Capacity Smart aluminized alloy drum Gas Dryer Quick Specs


Add to my manuals
4 Pages

advertisement

GE GTD75GCSLWS 7.4 cu. ft. Capacity Smart aluminized alloy drum Gas Dryer Quick Specs | Manualzz

GTD75GCPL/GCSL

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

EXHAUST OPTION: When viewed from the front of the unit, exhaust 3-way via rear, left and bottom.

Dryer is shipped exhausted to the rear. Alternate exhausting knockouts are supplied.

GAS: An individual, properly-grounded branch circuit, with a three-prong grounding-type receptacle, protected by a 15 or 20 amp circuit breaker or a time-delay fuse is required.

GAS DRYER ELECTRIC RATING: 120V, 60Hz, 6A

GAS (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply requires a conversion kit. Check installation instructions for correct kit and have a qualified gas technician install a conversion kit. See dryer ducting information for proper installation.

NOTE: Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position.

INSTALLATION INFORMATION: For complete information, see installation instructions packed with your dryer.

SPECIAL INSTALLATION REQUIREMENTS

ALCOVE OR CLOSET INSTALLATION:

- If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

- The dryer MUST be exhausted to the outside.

- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" either side; 1" front, top and rear

- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

BATHROOM OR BEDROOM INSTALLATION:

- The dryer MUST be exhausted to the outdoors.

- The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI

Z223 for gas dryers.

MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET

INSTALLATION:

- Minimum clearances to combustible surfaces are: 0" both sides; 1" rear

DRYER EXHAUSTING INFORMATION :

- Use metal duct only, vertical and horizontal ducting.

For answers to your Monogram, GE Café ™ Series, GE Profile ™ Series or

GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.

Specification Revised 9/17

GTD75GCPL/GCSL

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

5

22 1/2" 30 1/2"

27"

2

30-1/2

27"

Power Cord 4 1/2"

Back View

Power

Cord Hole

Back View

4-1/2

48"

40 1/2"

8"

3 1/2"

1 3/4"

3 1/4"

5"

Side View Rear View

For answers to your Monogram, GE Café ™ Series, GE Profile ™ Series or

GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.

Specification Revised 9/17

GE Dryer Vent

GTD75GCPL/GCSL GE Dryer Vent

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED

WITH YOUR DRYER.

DUCTING MATERIALS:

For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

EXHAUST LENGTH CALCULATION:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.

2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,

PLEASE CALL 1-800-GE-CARES.

DRYER EXHAUSTING INFORMATION—

USE METAL DUCT ONLY VERTICAL AND

HORIZONTAL DUCTING

BEST PERFORMANCE

A

A 4

B

Maximum length of 4" dia rigid metal duct

A

4 2-1/2

Number of 90° turns

Exhaust hood type

A

4" opening

B

2-1/2" opening

Long Vent 6.1-7.4 cu. ft.

2

3

0

1

4

5

120 ft.

100 ft.

85 ft.

70 ft.

60 ft.

55 ft.

90 ft.

75 ft.

65 ft.

55 ft.

45 ft.

35 ft.

For every extra 90° elbow, reduce the allowable vent system length by 10 ft.

Two 45° elbows will be treated like one 90° elbow.

For the side exhaust installations, add one 90° elbow to the chart.

When calculating the total vent system length, you must add all the straight portions and elbows of the system (including the transition duct.

Specification Revised 9/17

GTD75GCPL/GCSL

GE ® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry

FEATURES AND BENEFITS

Steam Select - For the best results, customize your cycle by specifying the number of garments needing to be steamed

WiFi Connect - Control and monitor your laundry from anywhere with a smart device or Amazon Alexa

HE Sensor Dry - Takes the guesswork out of drying times by sensing the moisture in the drum and drying accordingly

Up to 120 ft. venting capability - Provides flexible installation

Extended Tumble - Tumble clothes without heat to help prevent creasing and wrinkling

ENERGY STAR ® qualified - Meets or exceeds federal guidelines for energy efficiency for year-round energy and money savings

My Cycle Settings - Dry clothes with the settings you prefer on any cycle, rather than the defaults, and store your settings for later use

Damp Alert - Alerts you when clothes are the ideal dampness for ironing, for perfectly wrinkle-free results

Y-connector, short and long steam hoses included

Model GTD75GCSLWS – White with silver backsplash

Model GTD75GCPLDG – Diamond Gray

Sensor Dry ™

Cottons

Mixed Load

Casuals

Towels /Sheets Delicates

Bulky Items Speed Dry

Sanitize

Steam Refresh

3 - 5 Garments

Steam Dewrinkle

9 - 13 Garments

Jeans

Time Dry Cycles

Timed Dry

Warm Up

Est. Time Remaining

Delay Drying Cooling Done

90 min.

60

40

20

10

Time

More Dry

Dry

Less Dry

Damp

Level

High

Medium

Low

No Heat

Temp

Hold 3 Secs to Store

My

Cycle

Delay

Dry

Volume

Drum Light

Hold 3 Secs eDry

Time Adjust

Extended

Tumble

Control Lock

Hold 3 Seconds

Specification Revised 9/17

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement