GE GTDP740EDWW 7.8 cu. ft. capacity electric dryer Quick Specs


Add to my manuals
3 Pages

advertisement

GE GTDP740EDWW 7.8 cu. ft. capacity electric dryer Quick Specs | Manualzz

GTDP740ED

GE ® 7.8 cu. ft. capacity electric dryer

Dimensions and Installation Information (in inches)

Electric Dryer Rating:

240V 5000W 25A 60Hz

208V 4784W 23A 60Hz

Exhaust Option: 4-way rear, right, left and bottom

Circuit Requirements: An individual, properly-grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.

Note: Dryer wall outlet must be located within 36" of service cord entry and acessible when dryer is mounted in position.

Installation Information: For complete information, see installation instructions packed with your dryer.

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side; 3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.

• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

Minimum Clearances other than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear

Dryer Exhausting Information : Use metal duct only, vertical and horizontal ducting.

For answers to your Monogram, ® GE Profile ™ or

GE ® appliance questions, visit our website at geappliances.com or call GE Answer Center ® service, 800.626.2000.

Power Cord Locations 7.8 cu. ft. dryers

Listed by

Underwriters

Laboratories

Specification Revised 4/15

GE Dryer Vent

GE Dryer Vent

GTDP740ED

GE ® 7.8 cu. ft. capacity electric dryer

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.

A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.

2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a

90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

For every extra 90° elbow, reduce the allowable vent system length by 10 ft.

Two 45° elbows will be treated like one 90° elbow.

For the side exhaust installations, add one 90° elbow to the chart.

The total vent system length includes all the straight portions and elbows of the system (transition duct included).

Dryer exhausting information—use metal duct only vertical and horizontal ducting

A

4

A

A

B

Domestic dryer models

2-1/2

GE Frontload Long Vent 7.0 cu. ft. capacity electric dryer

(GFDL)

Long Vent 6.0 - 8.0 cu. ft. capacity electric & gas dryers

(GTDL and GTV)

Long Vent 7.0 cu. ft. capacity electric & gas (GTD42, GTD45,

GTD65, GTX42 and GTX60)

All 3.6 cu. ft. (DSKS, DSKP) electric dryers

4

2-1/2

B

All 6.0 - 8.3 cu. ft. capacity models electric and gas dryers

(GFDS, GFDR, GFDN, GTDS,

GTDN, GHDN, GHDS, GTDP,

GLDP, GTD, HTDP, HTDX)

DCVH480

Laundry Center GUD27

Laundry Center GUD24

35 ft.

46 ft.

37 ft.

30 ft.

23 ft.

56 ft.

45 ft.

35 ft.

25 ft.

90 ft.

60 ft.

45 ft.

48 ft.

40 ft.

32 ft.

43 ft.

33 ft.

24 ft.

135 ft.

125 ft.

115 ft.

105 ft.

95 ft.

120 ft.

100 ft.

85 ft.

70 ft.

60 ft.

55 ft.

90 ft.

60 ft.

Best performance

Maximum length of 4" dia rigid

metal duct

Exhaust hood type

A

4" opening

200 ft.

B

2-1/2" opening

175 ft.

185 ft.

165 ft.

175 ft.

155 ft.

165 ft.

145 ft.

155 ft.

135 ft.

145 ft.

125 ft.

150 ft.

125 ft.

115 ft.

105 ft.

95 ft.

85 ft.

75 ft.

90 ft.

75 ft.

65 ft.

55 ft.

45 ft.

35 ft.

60 ft.

45 ft.

25 ft.

37 ft.

30 ft.

22 ft.

15 ft.

42 ft.

35 ft.

25 ft.

15 ft.

60 ft.

45 ft.

35 ft.

34 ft.

26 ft.

18 ft.

36 ft.

26 ft.

16 ft.

2

3

4

0

1

4

5

1

2

3

4

5

0

1

2

3

4

5

0

Number of 90° turns

0

1

2

3

3

0

1

2

1

2

2

3

0

3

0

1

0

1

2

Specification Revised 4/15

GTDP740ED

GE ® 7.8 cu. ft. capacity electric dryer

Features and Benefits

• HE Sensor Dry - Keep your clothes looking and feeling their best. Dual thermistors continually monitor temperature with a sensor bar that measures moisture to prevent over-drying

• 5 heat selections provide the right temperatures for your clothes-drying needs

• eMonitor - Get the energy-saving insight you need to reduce your utility bills with an electronic readout that shows the efficiency level of each load

• eDry ™ - Save up to 10% on energy costs without sacrificing drying performance, thanks to this option that reduces temperatures on select cycles

• Model GTDP740EDWW – White on white

Specification Revised 4/15

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement