GE ZISB360DK Monogram 36" Smart Built-In Side-by-Side Refrigerator Quick Specs


Add to my manuals
14 Pages

advertisement

GE ZISB360DK Monogram 36

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

SECTION 1

STANDARD INSTALLATION

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

ZISB360DK

SECTION 2

FLUSH INSET INSTALLATION

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

OVERALL DIMENSIONS

36"

(91.5)

ZISB360DK

STANDARD

INSTALLATION

25 1/2"

(64.8)

23 7/8"

(60.7)

( (

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

Shipping Weight

36" (91.44 cm)

84" (213.36 cm)

25 3/8"(64.453 cm)

20 5/8" (52.4 cm)

35 1/2" (90.2 cm)

83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

24" (61 cm)

1/4" OD copper tubing or GE

SmartConnect kit

675 lb (306.2 kg)

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

35"

(89.0)

** Allow 13"

(33.0) min

clearance for 130˚

** Allow 15"

(38.1) min

clearance for 130˚

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

** Allow

4"

(10.2) min

clearance to a wall for 90˚

** Allow

4"

(10.2) min

clearance to a wall for 90˚

door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

full 130° door swings for pan removal. If the 90° door stop position is used, pan access is

maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

ZISB360DX

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

STANDARD INSTALLATION

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap additional 7/16"

24"

(61)

1 9/16"

(3.97)

6"

(15.2)

47 1/2"

(120.7)

7/16"

20"

(50.8)

E

5"

(12.7)

*84 1/2"

*Trim will overlap

75"

(190.5 )

From floor to bottom of electrical area

3 1/4"

(8.3)

A

(90.2)

20"

24"

(50.8)

(61.0)

E

75"

(190.5 )

From floor to bottom of electrical area

7/16"

(1.1)

Trim overlap

5"

(12.7)

SIDE VIEW

W

3 1/2"

(8.9)

5"

(12.7)

3 1/2"

(8.9)

B

WATER

FRONT VIEW

5"

(12.7)

3 1/2"

(8.9)

WATER

FRONT VIEW SIDE VIEW

W

The refrigerator will project forward, slightly beyond adjacent cabinetry.

ANTI-TIP BRACKET

C

SOFFIT

D

SIDE VIEW INSTALLED

UNDER SOFFIT

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

ZISB480DX

TOP VIEW

2" x 4"

Cut to 35" Length

STANDARD INSTALLATION

ZISB360DH

Screws mounted into vertical wall studs

*84"

(213.4)

*Or installation height from floor

E

3/4"

Min.

Top Case Trim

Side View Top

Case Trim

Install Screws

Through Trim and Into

3/4" Min. Wood Brace

FRONT VIEW INSTALLED

WITH METAL WALL STUDS

AND NO SOFFIT

ZISB360DK

STANDARD

INSTALLATION

NOTES

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:

The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

Determine your installation construction and required anti-tip configuration:

C Installed Under Soffit

After installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exceed 24" deep. The top case trim overlaps the bottom of the soffit.

D Wooden Wall Studs and No

Soffit

• Cut a 2" x 4" block and secure to brackets provided.

• Secure brackets to back wall of opening at 84" or your installation height from the floor.

E Metal Wall Studs and No Soffit

This method requires securely fastened cabinets on both sides and a 3/4" minimum wood brace above unit, with it’s front surface

24" from back wall.

• After installing unit into opening, raise grille panel and attach metal case top trim to

3/4" minimum wood brace.

• The brace spanning the enclosure must be securely fastened to cabinets on both sides.

See Installation Instructions for detailed instructions.

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

CUSTOM SIDE PANELS

F

24"

(61.0)

3/16"

(.5)

*84"

(213.4)

*Depending on installation height

ZISB360DK

STANDARD

INSTALLATION

NOTES

F Side panels must be used whenever the sides of the refrigerator will be exposed.

The 1/4" side panels will slip into the side case trim.

Secure the panels to the refrigerator with stick-on hook and loop fastener strips.

Order the side panels from the cabinet manufacturer.

*3"- 4"

(7.6 - 10.2)

*Depending on installation height

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH

ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

1/4" FRAMED PANEL DIMENSIONS

A

D

Grille Panel

E

Dispenser

Cutout

F

G

B

PANEL ASSEMBLY CROSS SECTION

Trim

Door

1/4" Framed Panel

Supplied Handles

C

PANEL DIMENSIONS

A

1/4" Framed Panel 33 7/8"

B

9"

C D E

68 3/8" 14 9/16" 18 9/16"

ZISB360DK

STANDARD

INSTALLATION

NOTES

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.

1/4" Framed Panels:

For 1/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Freezer

Panel

Fresh

Food

Panel

Dispenser

Cutout

15 3/8"

(39.1)

DISPENSER CUTOUT

POSITION

F G

17 13/16" 3 1/8"

9 5/8"

(24.4)

3/4" OVERLAY PANEL DIMENSIONS

A

D

Grille Panel

E

Dispenser

Cutout

F

G

Freezer

Panel

Fresh

Food

Panel

B

C

PANEL ASSEMBLY CROSS SECTION

Trim

1/4" Backer Panel

Door

.10" Spacer Panel 3/4" Overlay Panel

Supplied Handles

PANEL DIMENSIONS

A

1/4" Backer Panel 33 7/8"

.10" Spacer Panel 33"

B

9"

8 3/8"

C D E

68 3/8" 14 9/16" 18 9/16"

67" 13 1/4" 17 1/4"

3/4" Overlay Panel 34 1/8" 9 1/4" 68 5/8" 14 13/16" 18 13/16"

.25" + .10" + .75" = 1.10" Total Panel Thickness

Dispenser

Cutout

15 3/8"

(39.1)

9 5/8"

(24.4)

* DISPENSER CUTOUT

POSITION

F G

17 15/16" 3 1/4"

* Cut the dispenser opening after the backer, spacer and overlay panels have been assembled.

3/4" Overlay Panels:

For 3/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim.

The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim.

A spacer panel 0.10" thick must be placed between the overlay and backer panels.

Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Door Handles:

The supplied handles can be adjusted to accommodate both framed or overlay panels.

Custom handles of your choice, supplied by your cabinet maker, can also be installed.

ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels.

Kits include one handle. Order 2 kits for side-by-side refrigerators from your Monogram supplier.

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

DISPENSER TRIM

1/4" Framed Panel

Freezer Door

Ice/Water Dispenser

1/4" PANEL DISPENSER TRIM

A

1/4"

Total

Thickness

1/4" Backer Panel

Freezer Door

.10" Spacer Panel

Ice/Water Dispenser

3/4" Overlay Panel

3/4" OVERLAY PANEL

DISPENSER TRIM

B

1.10"

Total

Thickness

RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS

16 3/4"

10 5/8"

DISPENSER TRIM

1/4" Backer Panel

.10" Spacer

3/4" Overlay Panel

C

1.10"

Total

Thickness

D

SIDE VIEW CROSS SECTION

(SHOWING RAISED OVERLAY

WITH MIDDLE RAIL)

ZISB360DK

STANDARD

INSTALLATION

NOTES

These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels.

1/4" Panel Dispenser Trim:

The framed panel must be 1/4" nominal thickness to fit the dispenser trim.

• The dispenser trim fits over the custom panel and snaps into the freezer door.

• If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit.

• If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door.

3/4" Overlay Panel Dispenser Trim:

The 3/4" overlay dispenser trim is designed to fit a total panel thickness of 1.100".

• If the panel is less than 1.100" thick, a noticeable gap may be created around the dispenser trim.

• If the panel is more than 1.100" thick, the dispenser trim cannot be secured to the door.

• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.

• Alternative panel construction methods such as securing a

3/4" panel to a 1/4" backer panel cannot be used. Another method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required

1.100" panel thickness.

• When a raised panel design is to be used, a custom middle rail is required.

Raised Overlay Panel Design on

Dispenser Models:

When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.

• The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.

• The middle rail must be 1.10" total thickness to accept the dispenser trim.

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

OVERALL DIMENSIONS

AFTER PANEL INSTALL

38"

(96.5)

11 11/16"

(29.7)

ZISB360DK

FLUSH INSET

INSTALLATION

26"

(66.0)

20 5/8"

(52.4)

84 1/2"

(214.6)

15 3/8"

(39.1)

72 5/8"

(184.5)

* 83 1/2"

( 212.1)

68 5/8"

(174.3)

*39 17/32"

(100.4)

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

38" (96.5 cm)†

84 1/2" (214.6 cm) †

26" (66.0 cm) †

20 5/8" (52.4cm)

39" (99.1 cm)

85" (215.9cm)

26 3/16" (66.5 cm)

1/4" OD copper tubing or GE

SmartConnect kit

675 lb (306.2 kg) Shipping Weight

† Dimensions include 3/4" custom cabinet panel

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

FRONT VIEW

4"

(10.2)

Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84".

35"

(89.0)

Case width

SIDE VIEW

**13"

(33.0)

**15"

(38.1)

*115° Door swing

Doors can be adjusted to

90° door swing

20 5/8"

(52.4)

** Allow

4"

(10.2) min

clearance to a wall

for 90˚ door swing

TOP VIEW

** Allow

4"

(10.2) min

clearance to a wall

for 90˚ door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan

access is maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

ZIS360DH Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR ZISB360DK

FLUSH INSET INSTALLATION

3/4" PANELS

5 1/4"

(13.3)

47 1/2"

(120.7)

20"

(50.8)

3/4" Panel

TOP VIEW

Case

Finished cleats

Case Trim

3 1/4"

26 3/16"

(66.5)

Flush inset depth

6"

(15.2)

E

20 15/16"

(53.2)

Depth to cleat 5"

(12.7)

3/4"

(1.9)

Width of side cleats

39"

(99.1) Flush inset width

37 1/2"

(95.3)

Width between cleats

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap additional 7/16"

6"

(15.2)

E

5"

(12.7)

12"

(30.5)

24"

(61.0)

1/2"

(1.3)

Finished cleats

75"

(190.5 )

From floor to bottom of electrical area

85"

(215.9)

85"

(215.9)

75"

(190.5 )

From floor to bottom of electrical area

7/16"

(1.1)

Trim overlap

A

FLUSH INSET

INSTALLATION

NOTES

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:

The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

SIDE VIEW

W

ANTI-TIP BRACKET

C

SOFFIT

WATER

D

7"

(17.8)

WATER

FRONT VIEW

B

7"

(17.8) 3 1/2"

(8.9)

SIDE VIEW

W

2" x 4"

Cut to 35" Length

FLUSH INSTALLATION

ZISB360DH

Screws mounted into vertical wall studs

*84"

(213.4)

*Or installation height from floor

Determine your installation construction and required anti-tip configuration:

C Cut a 1" x 4" block 35" long.

Measure and mark under the soffit,

5 1/4" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84".

D Wooden Wall Studs and No Soffit

• Cut a 2" x 4" block and secure to brackets provided.

• Secure brackets to back wall of opening at 84" or your installation height from the floor.

See Installation Instructions for detailed instructions.

SIDE VIEW INSTALLED

UNDER SOFFIT

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

ZISB480DX

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR ZISB360DK

FLUSH INSET INSTALLATION

1/2" PANELS

5 3/8"

(13.7)

47 1/2"

(120.7)

20"

(50.8)

TOP VIEW

Case

Finished cleats

Case Trim

3 1/4"

(8.3)

1/2" Panel

26 3/16"

(66.5)

Flush inset depth

20 13/16"

(52.9)

Depth to cleat

E

5"

(12.7)

3/4"

(1.9)

Width of side cleats

39"

(99.1) Flush inset width

37 1/2"

(95.3)

Width between cleats

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap additional 7/16"

6"

(15.2)

E

5"

(12.7)

12"

(30.5)

Finished cleats

75"

(190.5 )

From floor to bottom of electrical area

85"

(215.9)

85"

(215.9)

24"

(61.0)

1/2"

(1.3)

7/16"

(1.1)

Trim overlap

FLUSH INSET

INSTALLATION

NOTES

A Mounting the junction box in this location will also allow for front accessibility through access panel.

75"

(190.5 )

From floor to bottom of electrical area

A

B Water supply area.

WARNING:

The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

3 1/2"

(8.9)

SIDE VIEW

W

ANTI-TIP BRACKET

C

SOFFIT

WATER

FRONT VIEW

(8.9)

D

7"

(17.8)

B

WATER

FRONT VIEW

7"

(17.8) 3 1/2"

SIDE VIEW

W

2" x 4"

Cut to 35" Length

Determine your installation construction and required anti-tip configuration:

C Cut a 1" x 4" block 35" long.

Measure and mark under the soffit, 5 3/8" from the front edge of the cabinet. Secure the wood block under the soffit.

From the bottom of the block to the finished floor should measure 84".

Screws mounted into vertical wall studs

FLUSH INSTALLATION

ZISB360DH

*84"

(213.4)

*Or installation height from floor

D Wooden Wall Studs and No

Soffit

• Cut a 2" x 4" block and secure to brackets provided.

• Secure brackets to back wall of opening at 84" or your installation height from the floor.

See Installation Instructions for detailed instructions.

SIDE VIEW INSTALLED

UNDER SOFFIT

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

ZISB480DX

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

FLUSH INSET 3/4" PANEL DIMENSIONS

A

PANEL DIMENSIONS

Grille Panel B

D E

A

38"

B C D E

11 3/16" 68 5/8" 16 7/8" 20 7/8"

Dispenser

Cutout

F

G

C

Dispenser

Cutout

15 3/8"

(39.1)

DISPENSER CUTOUT

POSITION

F G

17 23/32" 3 3/8"

9 5/8"

(24.4)

Freezer

Panel

Fresh

Food

Panel

3/4" RAISED DOOR PANEL ROUTING

11/32"

1/4"

DETAIL TOP

3/4" NOTE: Routed areas should be finished as they may be visible when assembled.

1/4" 7/16" Front

TOP

ZISB360DK

FLUSH INSET

INSTALLATION

NOTES

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required.

The router depth is 1/4" all the way around the panel’s backs.

Additional panel width reductions are required per the diagrams shown. This will create “picture frame” routing allowing the panels to slide into the attached door and grille trims.

MAXIMUM TOTAL PANEL WEIGHT:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

DOOR HANDLES

Door handle not included.  A custom handle supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels.  Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel handle designed to fit

3/4" panels.  Kit includes one handle – 64 1/4" long.

Back

Back Front

3/16"

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL BOTTOM

DETAIL HINGE

SIDE

ROUTER DEPTH 1/4"

2 1/16"

Front

HINGE

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

3/16"

DETAIL HANDLE

SIDE

HANDLE

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

3/4" RAISED GRILLE PANEL ROUTING

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

DETAIL TOP

TOP

Back

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL

LEFT SIDE

ROUTER DEPTH 1/4"

2 1/16"

2"

3/16"

DETAIL BOTTOM

Back

DETAIL RIGHT

SIDE

ROUTER DEPTH 1/4"

2 1/16"

Front

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

ZISB360DK

FLUSH INSET

INSTALLATION

NOTES

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required.

The router depth is 1/4" all the way around the panel’s backs.

Additional panel width reductions are required per the diagrams shown. This will create “picture frame” routing allowing the panels to slide into the attached door and grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Door Handles

Door handle not included. A custom handle supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel handle designed to fit

3/4" panels.  Kit includes one handle – 64 1/4" long.

Front

LEFT

SIDE

RIGHT

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR ZISB360DK

DISPENSER TRIM

A

Freezer Door

Ice/Water Dispenser

3/4" Flush Panel

3/4" OVERLAY PANEL

DISPENSER TRIM

10 5/8"

DISPENSER TRIM

1/4" Backer Panel

Freezer Door

.10" Spacer Panel

Ice/Water Dispenser

1/2" Overlay Panel

1/2" OVERLAY PANEL

DISPENSER TRIM

.85"

Total

Thickness

RAISED PANEL DESIGN ON DISPENSER MODELS

16 3/4"

3/4" or 1/2" Flush Panel

B

3/4" or .85"

Total

Thickness

C

SIDE VIEW CROSS SECTION

(SHOWING RAISED PANEL WITH

MIDDLE RAIL)

FLUSH INSET

INSTALLATION

NOTES

These refrigerators are supplied with a dispenser trim for flush inset panels.

A Panel Dispenser Trim:

The provided dispenser trim is designed to fit a total panel thickness of 3/4" or 0.85".

• If the panel is less than 3/4" thick, a noticeable gap may be created around the dispenser trim.

• If the panel is more than 0.85" thick, the dispenser trim cannot be secured to the door.

• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.

• When a raised panel design is to be used, a custom middle rail is required.

Raised Panel Design on

Dispenser Models:

When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.

B • The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.

C • The middle rail must be 3/4" total thickness for 3/4" panels or 0.85" total thickness for 1/2" panels to accept the dispenser trim.

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

FLUSH INSET 1/2" PANEL DIMENSIONS

A

D

Grille Panel

Dispenser

Cutout

F

E

B

PANEL DIMENSIONS

A

1/4" Backer Panel 33 7/8"

.10" Space Panel 33"

1/2" Overlay Panel 38"

B

9"

C D E

68 3/8" 14 9/16" 18 9/16"

8 3/8" 67" 13 9/16" 17 9/16"

11 3/16" 68 5/8" 16 7/8" 20 7/8"

G

Freezer

Panel

Fresh

Food

Panel

C

Dispenser

Cutout

15 3/8"

(39.1)

DISPENSER CUTOUT

POSITION

F G

17 23/32" 3 3/8"

9 5/8"

(24.4)

1/4" BACKER ASSEMBLY ROUTING DIMENSIONS

Hinge Side

ZISB360DK

FLUSH INSET

INSTALLATION

NOTES

The 1/2" overlay panel must be secured to a .10" spacer panel and a

1/4" thick backer panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.

• Refer to the chart for locating the backer panel to the overlay panel.

Secure the overlay panel to the backer panel with glue and screws.

Screws must be countersunk into the backer panel.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

C C

Door

1/2"

Overlay

Panel

Backer with

Overlay Panel

Assembly

D

Freezer

Back

Fresh Food

Back

D

1/4"

Backer

Panel

.10"

Spacer

B A A

PANEL DIMENSIONS

A B

Fresh Food Panel 2 1/16" 1/16"

Freezer Panel 2 1/16" 1/16"

Grille Panel 2 1/16" 2 1/16"

C

1/8"

1/8"

2"

B

D

1/8"

1/8"

7/32"

A

C

Grille Back

D

B

Product Specification Revised 1/18

MONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

FEATURES AND BENEFITS

ADVANCED TEMPERATURE MANAGEMENT SYSTEM WITH

MULTI-SHELF BRUSHED ALUMINUM AIR TOWER

Provides even distribution of air throughout the refrigerator

CLIMATE-CONTROL DRAWER

Allows you to express-chill beverages, express-thaw meats and select specific temperatures for perishable foods

WIFI CONNECT

Enjoy the convenience and freedom of wirelessly controlling functions from your smartphone

LED LIGHTING

Light columns in the freezer and fresh food compartments extend the full length of the interior and LED lighting located inside the vegetable and climate-control drawers illuminate contents without compromising space

COLOR-MATCHED DISPENSER WITH PROXIMITY SENSOR

Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away

GE® WATER FILTER

Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight

DELI DRAWER ON FULL-EXTENSION SLIDES

Keeps meats, cheeses and other everyday foods within easy reach

HUMIDITY-CONTROLLED VEGETABLE DRAWER

Helps preserve the freshness of foods

ADJUSTABLE GLASS SHELVES

Easily accommodate party trays and platters

GALLON-SIZE DOOR BIN

Holds milk containers, two-liter bottles and pitchers

ADJUSTABLE DOOR BINS

Can be moved to one of two positions in seven locations

DAIRY BIN WITH CENTER DIVIDER

Has a unique magnetic seal that locks in freshness

FILTER-CHANGE INDICATOR LIGHT

Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser

ZISB360DK

R

Product Specification Revised 1/18

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement