GE DRSR495GGWW 7.0 Cu. Ft. Super Capacity Gas Dryer Quick Specs


Add to my manuals
3 Pages

advertisement

GE DRSR495GGWW 7.0 Cu. Ft. Super Capacity Gas Dryer Quick Specs | Manualzz

25-1/2

27

42

51

36

Side View Rear View

DRSR495GG

GE ® 7.0 Cu. Ft. Super Capacity Gas Dryer with Stainless Steel Drum

23-1/2 28-1/4 *24-1/2" from the edge of the side panel to the front.

25-1/2" from front to edge of endcaps.

Dimensions and Installation Information (in inches)

Exhaust Option: When viewed from the front of the unit, exhaust 3-way via rear, left and bottom. Dryer is shipped exhausted to the rear. Alternate exhausting knockouts are supplied.

Gas: An individual, properly-grounded branch circuit, with a three-prong groundingtype receptacle, protected by a 15 or 20 amp circuit breaker or a time-delay fuse is required.

Gas Dryer Electric Rating: 120V, 60Hz, 6A

Gas (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply requires a conversion kit. Check installation instructions for correct kit and have a qualified gas technician install a conversion kit. See dryer ducting information for proper installation.

5.7 cu. ft. Dryers

Note: 2

36" of service cord entry and accessible when dryer is mounted in position.

Installation Information: For complete information, see installation instructions packed with your dryer.

Power

Cord Hole

30-1/2

For answers to your Monogram, ® GE Profile ™ or

GE ® appliance questions, visit our website at ge.com or call GE Answer Center ® service,

800.626.2000.

Back View

Washer/Dryers SC QSart

Power

Cord Hole

Back View

25-1/2*

8-1/2

Side View

5

4-1/2

36

42

2-1/2

11-1/2

2

27

3-1/2

Rear View

Specification Revised 8/09 370162

DRSR495GG

GE ® 7.0 Cu. Ft. Super Capacity Gas Dryer with Stainless Steel Drum

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.

A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.

2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a

90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label

on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side; 3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.

• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

Minimum Clearances other than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear

Dryer Exhausting Information : Use metal duct only, vertical and horizontal ducting.

A

4

B

A

Best performance

Maximum length of 4" dia. rigid metal duct

Exhaust hood type

Domestic dryer models

2-1/2

7.0, 6.0 and 5.8 cu. ft.

capacity models all gas dryers

Number of

90° turns

0

1

2

3

A

4" opening

90 ft.

60 ft.

45 ft.

35 ft.

B

2-1/2" opening

60 ft.

45 ft.

35 ft.

25 ft.

Specification Revised 8/09 370162

DRSR495GG

GE ® 7.0 Cu. Ft. Super Capacity Gas Dryer with Stainless Steel Drum

Features and Benefits

• 7.0 cu. ft. Super Capacity - Handles large-size items and family-size loads

• Stainless Steel Drum - Resists rust and won't chip, peel or snag clothes

• Four Heat Selections - Provide the right temperature for the right drying results

• Nine Dry Cycles - Includes sensor dry cottons, optional wrinkle care, sensor dry easy care, sensor dry delicates, timed dry, dewrinkle, quick fluff (no heat) and damp dry

• Sensor Dry Plus - Continually monitors moisture levels to help clothes look better longer

• Variable End-Of-Cycle Signal - Alert sounds whenever cycle is complete and adjustable volume provides added convenience

• Quiet-By-Design ™ - Special insulating materials help muffle operating noise

• Interior Dryer Light - Lets you see everything inside for easy loading and unloading

• Model DRSR495GGWW –White on white

DRSR495E/G.EPS

Specification Revised 8/09 370162

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement