広告
広告
USER GUIDE 3.2.0 | August 2020 | 3725-86558-004A
Poly Video Mode
(G7500, Studio X50, and Studio X30)
Getting Help
For more information about installing, configuring, and administering Poly/Polycom products or services, go to
Polycom Support.
Plantronics, Inc. (Poly — formerly Plantronics and Polycom)
345 Encinal Street
Santa Cruz, California
95060
© 2020 Plantronics, Inc. All rights reserved. Poly, the propeller design, and the Poly logo are trademarks of Plantronics, Inc.
All other trademarks are the property of their respective owners.
Contents
LED Status Indicators for the Studio X50 and Studio X30 Systems........................ 7
Overview of Poly G7500, Studio X50, and Studio X30 Hardware.......................................8
Poly Studio X50 and Studio X30 Privacy Cover.....................................................10
Users Who Are Blind, Have Low Vision, or Have Limited Vision........................... 15
1
Cast Content from an AirPlay- or a Miracast-Certified Device............................... 23
Share Content Using an HDMI Connection............................................................24
Save a Camera Preset from the Local Interface.................................................... 27
Select the Primary Camera from the Local Interface............................................. 29
Using the System as a Camera and Audio Peripheral..................................30
Contents
2
Conferencing Application Doesn’t Use System Camera or Audio..........................34
Contents
3
Before You Begin
Topics:
▪
Audience, Purpose, and Required Skills
▪
Related Poly and Partner Resources
This guide contains overview information, procedures, and references you can use to perform tasks with your video system.
The information in this guide applies to all the following Poly video systems except where noted:
▪ Poly G7500 (model: P011)
▪ Poly Studio X50 (model: P017)
▪ Poly Studio X30 (model: P018)
Audience, Purpose, and Required Skills
This guide is intended for beginning users, as well as intermediate and advanced users, who want to learn more about the features available with the system.
Related Poly and Partner Resources
See the following sites for information related to this product.
▪ The Poly Online Support Center is the entry point to online product, service, and solution support information including Video Tutorials, Documents & Software, Knowledge Base, Community
Discussions, Poly University, and additional services.
▪ The Polycom Document Library provides support documentation for active products, services, and solutions. The documentation displays in responsive HTML5 format so that you can easily access and view installation, configuration, or administration content from any online device.
▪ The Polycom Community provides access to the latest developer and support information. Create an account to access Poly support personnel and participate in developer and support forums. You can find the latest information on hardware, software, and partner solutions topics, share ideas, and solve problems with your colleagues.
▪ The Polycom Partner Network are industry leaders who natively integrate the Poly standards-based
RealPresence Platform with their customers’ current UC infrastructures, making it easy for you to communicate face-to-face with the applications and devices you use every day.
▪ The Polycom Collaboration Services help your business succeed and get the most out of your investment through the benefits of collaboration.
4
Getting Started
Topics:
▪
Product Overview of Poly Video Systems
▪
▪
Overview of Poly G7500, Studio X50, and Studio X30 Hardware
▪
▪
Powering the System On and Off
▪
▪
Before you use your system, familiarize yourself with its features and user interface.
Product Overview of Poly Video Systems
Poly G7500, Studio X50, and Studio X30 systems in Poly Video Mode support Poly video conferencing and content sharing features.
Poly G7500 System Features and Capabilities
G7500 systems support the following features:
▪ Peripheral cameras and microphones make the system scalable for medium rooms and up to large integrated rooms
▪ Placing and joining video calls
▪ Viewing and joining scheduled calendar meetings
▪ Managing contacts, call lists, and directories
▪ Sharing wireless and wired content
▪ Collaborating with electronic blackboards
▪ Camera tracking technology that can automatically zoom in on the person talking or frame the group of people in the room (depending on how you configure the system)
▪ Poly NoiseBlockAI, which eliminates background and extraneous sound during calls in common working environments
▪ Polycom Acoustic Fence technology, which enables video conferencing in open workspaces by capturing only the voices in a defined area
▪ HDMI: Single input and dual output
▪ Serial port connection
Poly Studio X50 Features and Capabilities
Studio X50 systems support the following features:
▪ All-in-one collaboration system for huddle rooms and small-to-medium rooms
5
Getting Started
▪ No need for a separate PC, laptop, or codec to run video-conferencing software
▪ Placing and joining video calls
▪ Viewing and joining scheduled calendar meetings
▪ Managing contacts, call lists, and directories
▪ Sharing wireless and wired content
▪ Collaborating with electronic blackboards
▪ Built-in 4K camera with ultra-wide 120-degree field of view
▪ Camera tracking technology that automatically frames the group of people in the room
▪ Hi-fidelity, built-in stereo microphones that pick up sound within 7.62 m (25 ft) and use spatial audio for life-like presence and clarity
▪ Poly NoiseBlockAI, which eliminates background and extraneous sound during calls in common working environments
▪ Dual stereo speakers
▪ HDMI: Single input and dual output
Poly Studio X30 Features and Capabilities
Studio X30 systems support the following features:
▪ All-in-one collaboration system for huddle rooms and small-to-medium rooms
▪ No need for a separate PC, laptop, or codec to run video-conferencing software
▪ Placing and joining video calls
▪ Viewing and joining scheduled calendar meetings
▪ Managing contacts, call lists, and directories
▪ Sharing wireless and wired content
▪ Collaborating with electronic blackboards
▪ Built-in 4K camera with ultra-wide 120-degree field of view
▪ Camera tracking technology that automatically frames the group of people in the room
▪ High-fidelity, built-in stereo microphones that pick up sound within 4.57 m (15 ft) and use spatial audio for life-like presence and clarity
▪ Poly NoiseBlockAI, which eliminates background and extraneous sound during calls in common working environments
▪ Single mono speaker
▪ HDMI: Single input and output
LED Status Indicators
The following figures display the LEDs on your systems. The tables list each LED indicator and its associated status.
LED Status Indicators for the G7500 System
Use the LED on the front right corner of the codec to get information on the state of your system.
6
Getting Started
G7500 System LED Status Indicators
Indicator
Blinking white
Solid white
Blinking amber
Solid amber
Blinking red
Status
Powering on
Working normally
Update in progress
Sleeping
Error preventing normal operation
LED Status Indicators for the Studio X50 and Studio X30 Systems
The system provides an LED light bar above the camera to help you understand the system’s behaviors.
Basic Studio X50 and Studio X30 LED Indicators and Status
Indicator
Solid white
Blinking blue
Solid blue for 3 seconds
Blinking green
Solid green
Position
All
Twelve in the middle
All
All
All
Status
Boot initialization in progress
Bluetooth in discovery
Bluetooth paired
Incoming call
Outgoing call
7
Getting Started
Indicator
Solid green
Solid amber
Pulsing red
Pulsing green
Solid white for 3 seconds
Solid red
Pulsing amber
Blinking red
Overview of Poly G7500, Studio X50, and Studio X30
Hardware
The following figures and tables provide information about hardware features available on your system.
Poly G7500 Hardware
The following figure displays the hardware features on the Poly G7500 system. The table lists each feature numbered in the figure.
8
Getting Started
2
3
4
Poly G7500 Feature Descriptions
Ref. Number Feature
1 Reset button
LED indicator
Remote control pairing button
Restart button
Feature Description
Resets the Poly G7500 to the factory software version
Indicates the system status
Enables the Bluetooth remote control pairing mode
Restarts your system
Poly Studio X50 Hardware
The following figure displays the hardware features on the Poly Studio X50 system. The table lists each feature numbered in the figure.
Poly Studio X50 Feature Descriptions
Ref. Number Feature
1 Screen
2
3
Microphone array
Camera
Feature Description
Protective screen that covers the front of your system
Microphone array that captures audio
Camera with a privacy cover that enables or disables the video input as you choose
9
Getting Started
Ref. Number
4
5
Feature
Speakers
LED indicators
Feature Description
Stereo audio output
Indicates the system status and information on the tracked speaker
Poly Studio X30 Hardware
The following figure displays the hardware features on the Poly Studio X30 system. The table lists each feature numbered in the figure.
3
4
Poly Studio X30 Feature Descriptions
Ref. Number
1
2
Feature
Microphone array
LED indicators
Camera
Speaker
Feature Description
Microphone array that captures audio
Indicates the system status and information on the tracked speaker
Camera with a privacy cover that enables or disables the video input as you choose
Mono audio output
Poly Studio X50 and Studio X30 Privacy Cover
The Poly Studio X50 and Studio X30 systems provide a physical cover that you can place over the camera lens to protect your privacy.
10
Getting Started
Navigating Your System
The system has icons and user screens to help you navigate and understand important information about your system.
Home Screen
The Home screen is the first screen you encounter on the system monitor. From this screen, you have quick access to many of the system functions.
Note: Some elements of your screen may be different depending on the system configuration.
11
Getting Started
Home Screen
2
3
4
Ref. Number
1
Description
System information bar, which shows details such as date/time and system name.
Task buttons for placing calls, sharing content, creating a blackboard, or launching Poly Device Mode.
Menu for accessing other features.
Local camera view.
Home Screen Elements
Some of the following interactive and read-only elements might not display on your system depending on the system configuration.
Element
Name
Security code
Description
Descriptive name determined by the system administrator. Used when you want to connect to a system.
Displays after you attempt a content sharing connection. Use the four-digit code to set up wireless connections through the Polycom Content App or an
AirPlay- or a Miracast-certified device.
12
Getting Started
Element
IP address
Current time
Current date
Warning
Calendar or Favorites cards
Place a Call
Content
Blackboard
Poly Device Mode
Menu
Description
IP address, SIP, H.323, or secondary network configured for your system.
Local time zone.
Local time zone date.
Notification that the system has detected one or more problems that might prevent it from fully functioning.
View your calendar or favorites.
Opens a call screen where you can dial a call, or you can select a card to dial numbers, access favorites, or view your calendar.
When content is available, the system displays a list of available content.
Otherwise, this function opens a help screen that describes how to set up content sharing using HDMI, the Polycom Content App, or an AirPlay- or a
Miracast-certified device.
Creates a new blackboard, where you can share annotations or drawings.
Launches Poly Device Mode, which allows you to use the system as an external camera, microphone, and speaker for your connected laptop.
Opens new menu selections for calling, sharing content, camera control, and additional functions.
Content Screen
The Content screen is where you share and annotate content in your meetings.
13
Getting Started
Content Screen
3
4
Ref. Number
1
2
Description
Camera views of call participants.
System information bar, shows system information such as system name and time.
Content toolbar, provides tools to annotate and work with content.
Content management functions.
Powering the System On and Off
The system turns on when you plug it into a power source. The system doesn’t have a power button, so you must unplug the power cable to power it off.
Note: Don’t power off the system during maintenance activities (for example, while a software update is in progress).
Wake the System
After a period of no activity, the system enters sleep mode (if configured by your administrator). You can wake it using a touch monitor, Poly TC8, or Poly Bluetooth Remote Control.
14
Getting Started
Procedure
» Do one of the following:
▪ If you’re using a touch monitor, tap the primary screen.
▪ If you’re using the TC8, tap the screen.
▪ If you’re using a Poly Trio, tap the screen.
▪ Press any button on the remote control.
Accessibility Features
Polycom products include a number of features to accommodate hearing-, vision-, mobility-, or cognitively-impaired users.
Users Who Are Deaf or Hard of Hearing
Your system includes accessibility features for users who are deaf or hard of hearing to use the system.
The following table lists the accessibility features for users who are deaf or hard of hearing.
Accessibility Features for Users Who Are Deaf or Hard of Hearing
Accessibility Feature
Visual notifications
Status indicator lights
Adjustable call volume
Description
Status and icon indicators let you know when you have incoming, outgoing, active, or held calls. Indicators also alert you of the device’s status and when features are enabled.
The system and its microphones use LEDs to indicate some statuses, including if your microphones are muted.
While in a call, you can raise or lower the volume of the device.
Users Who Are Blind, Have Low Vision, or Have Limited Vision
Your system includes accessibility features for users who are blind, have low vision, or have limited vision to use the system.
The following table lists the accessibility features for users who are blind, have low vision, or have limited vision.
Accessibility Features for Users Who Are Blind, Have Low Vision, or Have Limited Vision
Accessibility Feature Description
Auto-answering You can enable the phone to auto-answer calls.
Mute auto-answered calls
Ringtones
Join and leave tones
You can configure the system to mute auto-answered calls.
An audible tone plays for incoming calls.
The system plays a tone when someone joins or leaves a conference call.
15
Getting Started
Accessibility Feature
Embossed buttons
Description
The remote control has embossed push buttons for performing common tasks with the system, such as dialing a number.
Users with Limited Mobility
Your system includes accessibility features to enable users with limited mobility to use various system features.
The following table lists the accessibility features for users with limited mobility.
Accessibility Features for Users with Limited Mobility
Accessibility Feature
Remote control
Poly TC8
Auto-answering
Calling from a personal device
Touch-capable monitor support
Description
The Bluetooth remote control enables you to control the system and to perform tasks such as placing calls, starting a sharing session, and configuring some settings.
The TC8 enables you to control the system and to perform tasks such as placing calls.
You can enable the system to auto-answer calls.
With administrator credentials, you can wirelessly access the system web interface from your own device to make calls and manage contacts and favorites.
If you have a touch-capable monitor connected to the system, you can select, swipe, and press the screen to perform functions and activate features.
16
Calling
Topics:
▪
▪
▪
▪
Joining Meetings from the Calendar
▪
Using the System as a Camera and Audio Peripheral
There are several ways to initiate calls on the system. You can place a call by entering your contact’s name or number, choosing a contact in the directory, calling a favorite or recent contact, or joining a scheduled meeting.
You can place calls using the following methods:
▪ Call using the dialpad
▪ Call a contact
▪ Call a frequently used number
▪ Call a recent contact
▪ Call a favorite
▪ Join a meeting from the calendar
▪ Call using a USB-connected Windows or Mac device
Placing Calls
You can place audio calls, video calls, and call into meetings using the onscreen keyboard.
Use the following dialing formats when placing calls:
▪ IPv4 address: 192.0.2.0
▪ Host name: room.company.com
▪ SIP address: [email protected]
▪ H.323 or SIP extension: 2555
▪ Phone number: 9782992285
Place a Call
You can place an audio or video call to a contact.
Procedure
1.
Go to Place a Call .
2.
On the Dialpad screen, move the slider to Audio or Video .
3.
Enter a number on the dialpad or select Keyboard to enter characters.
17
Calling
4.
Select Call .
Answer a Call
The way the system handles incoming calls depends on how your administrator configured it. The system either answers the call automatically or prompts you to answer manually.
Procedure
» If you receive an incoming call notification, select Answer .
Ignore a Call
If the system doesn’t answer incoming calls automatically, you can choose to ignore the call rather than answer it.
Procedure
» If you receive an incoming call notification, select Ignore .
End a Call
When your call is complete, hang up the call. If you have content such as blackboards, whiteboards, or snapshots, the system asks if you want to keep them.
Procedure
» In a call, do one of the following:
▪ On your remote control, press Hang Up .
▪ On the screen, select Menu > Hang Up .
Calling Contacts
You can access and call contacts, recent contacts, and frequent contacts on your system.
If configured by your administrator, contacts display on the Place a Call screen. Contact cards can display the following information:
▪ Contact name
▪ Contact number
▪ Contact email address
▪ Contact IP address
Call a Contact
To quickly dial a contact, you can search and select a contact card from the results. Contact cards display for frequent contacts, directory contacts, and favorites.
Procedure
1.
Go to Place a Call > Contacts .
2.
In the search field, use the onscreen keyboard to type characters or numbers and select Search .
18
3.
Select a contact card to view contact details.
4.
Select Call .
Call a Frequent Contact
As you place calls, the system learns your frequently-used contacts and displays them in a list.
Procedure
1.
Go to Place a Call .
2.
Select a contact card from the Frequent list.
The call automatically dials.
Call a Recent Contact
You can quickly call recent contacts from a list (organized by most to least recent).
Procedure
1.
Go to Place a Call > Recent .
2.
Scroll through the list of recent contacts (sorted by date) and select one.
The call automatically dials.
Calling Favorite Contacts
To quickly access a short list of contacts you call most often, create favorites.
Favorites display on the Favorites , Contacts , or Home screens, depending on your system configuration. The system adds a star icon next to the contact’s name, providing you an easy way to identify and call favorites.
Favorite a Contact
Create favorites to display contacts that you call the most often.
Procedure
1.
Go to Place a Call > Contacts .
2.
Select a contact card, then select Favorite .
The contact receives a star icon and displays in the Contacts and Favorites lists.
Unfavorite a Contact
Unfavorite a contact to remove the contact from your Favorites list.
Procedure
1.
Go to Place a Call > Favorites .
2.
Choose a favorite card, then select Unfavorite .
The contact is removed from the Favorites list.
Calling
19
Calling
Call a Favorite Contact
To quickly call a contact, select a favorite card.
Procedure
1.
Select a favorite card on the Favorites , Contacts , or Home screen.
2.
Select Call .
Joining Meetings from the Calendar
On the Home screen, you can join meetings directly from your calendar using the meeting cards on the screen (if configured).
Note: If calendaring isn’t configured for your system, the system doesn’t display meeting cards. You must dial manually to join meetings.
Meeting Cards
If configured, meeting cards display on the Home screen. You can access meeting cards to view meeting details.
Meeting cards display the following scheduling information:
▪ All-day meetings display as the first meeting card.
▪ For meetings scheduled later in the day, a Free until [time/day] message displays, followed by upcoming meeting cards in the time and date order they’re scheduled.
▪ For meetings scheduled later in the week, a Free until [time/day] message displays until the day of the next scheduled meeting.
▪ If there are no scheduled meetings for the current week, a No Meetings message displays.
View Meeting Cards
On the Home screen, you can view meeting cards that show your calendar event details. Meeting cards display meeting times, subjects, and organizers.
Note: Private meetings are labeled Private Meeting . Except for the time, meeting details are hidden.
Procedure
» Do one of the following:
▪ To view meeting information, choose a meeting card and select Info .
▪ To view upcoming scheduled meetings, select a card and scroll to the right.
Join a Meeting from a Meeting Card
On the Home screen, you can select a meeting card for options to join a meeting.
The system supports automatic dialing if the meeting organizer added calling information to the calendar event and your administrator has configured calendaring.
20
Calling
Procedure
» Do one of the following:
▪ On a current meeting card, select Join .
▪ If the meeting card doesn’t include calling information, select More ...
the card to display the dialpad. Dial the number to join the meeting.
Join an Overbooked Meeting
If two or more meetings are scheduled at the same time, the meetings display as Overbooked . You can join one of the meetings using its individual meeting card.
Procedure
1.
Select an overbooked meeting card and choose Info .
The individual meeting cards display.
2.
Choose one of the meeting cards and select Join to connect to the meeting.
Join a Password-Protected Meeting
Some meetings may require a password to join.
Make sure that you have the password for password-protected meetings before you join. If you don’t have a meeting password and a message prompts you for one, contact the meeting organizer for the password.
Note: Meeting cards don’t indicate if a meeting is password protected.
Procedure
1.
Do one of the following:
▪ Manually dial in to a meeting.
▪ Join a meeting from a meeting card.
2.
Enter the meeting password and select Join .
If you enter an incorrect password, the password prompt displays again.
Using the System as a Camera and Audio Peripheral
With Poly Device Mode, you can use a Poly video system as your laptop’s external camera, microphone, and speaker.
For example, instead of using your laptop’s camera for Microsoft Teams calls, you can connect the Studio
X30 and use its 4K camera that automatically follows the conversation in the room. You also gain a Poly echo-cancelling microphone and speaker technology during calls.
Once you connect the system to your laptop with a USB cable, you can control the video system’s camera and audio features using your laptop’s third-party conferencing application. Remember the following about audio controls:
▪ You can also mute audio using the buttons on any connected microphones.
▪ If you mute audio from your app, the video system and microphone LEDs indicate you’re muted
(and vice versa).
21
Calling
If needed, you can also mirror your laptop’s screen on the video system’s monitors with an HDMI cable.
Laptop and Cable Requirements
Make sure that your laptop and USB cable allow you to use a Poly video system as a camera and audio accessory (i.e., Poly Device Mode).
Your laptop must have one of the following operating systems:
▪ Windows 10 version 1803 or later
▪ macOS version 10.12 or later
Remember when choosing a USB cable:
▪ Use a cable with at least one USB-C connection for your video system.
▪ If possible, use a USB 3.0 cable to ensure connection reliability and video and audio quality. (You can also use a USB 2.0 cable.)
▪ If you need a connection that’s longer than 2 m (6.6 ft), use a self-powered USB booster extension cable.
▪ Don’t use a cable used only for charging devices.
Connect a Windows or Mac Laptop
To use the video system as an external camera and audio accessory, you must enable Poly Device Mode and connect your laptop with a USB cable.
Note the following (contact your administrator if you need help):
▪ If your conferencing application uses echo cancellation, disable that feature.
▪ Poly Device Mode isn’t available if the video system’s USB ports are disabled.
▪ Use a cable with at least one USB-C connection for your video system.
Procedure
1.
On the Home screen, select Device Mode .
2.
Connect the USB cable to your laptop.
3.
Connect the USB-C end of the cable to the video system’s USB-C port.
4.
Optional: To mirror your laptop’s screen on a video system monitor, connect the laptop using the system’s HDMI input port.
Disconnect a Windows or Mac Laptop
Any camera options you change on the video system with your USB-connected laptop revert to their previous settings when you exit Poly Device Mode.
Procedure
» Do one of the following:
▪ On the video system local interface or TC8 device (if you have one), select Exit Mode .
▪ Unplug the cables connecting your laptop and video system. After a couple minutes, you see the video system home screen.
22
Sharing Content
Topics:
▪
Sharing Content from a Computer or Device
▪
Sharing Content on a Blackboard or Whiteboard
▪
▪
End a Call with Blackboard or Whiteboard Content
To enhance the collaboration experience, you can share documents, graphics, videos, and blackboards or whiteboards with other participants.
You can share content with all members of a call or meeting using a computer or a certified device.
Sharing Content from a Computer or Device
You can share content from a computer or use applications to stream content from other devices.
You can use the following methods to share content:
▪ Polycom Content App, which wirelessly connects to the system
▪ Screen mirroring with an AirPlay- or Miracast-certified device
▪ Computer or device directly connected to the system through HDMI
The system allows up to four simultaneous content sources out of a call and three in a call (a source can include content shared from a device in the room or by a far-end participant).
For example, if you’re in a call with three content sources and you share your desktop using the Content
App, the oldest wireless or far-end content source in the session is replaced by your content. HDMI content, however, is never replaced.
Important: Before you share content, take precautions to protect your privacy. For example, disable your device’s screen lock feature before you share your screen with meeting participants.
Polycom Content App
The Polycom Content App enables you to share content from a computer connected to a system over an
IP network.
For information on using this application, see the Polycom Content App User Guide .
Cast Content from an AirPlay- or a Miracast-Certified Device
You can share content from your Airplay- or Miracast-certified device and display it on the system.
Procedure
1.
Go to AirPlay or Miracast on your device.
2.
From the list of available devices, select the name of your system.
23
Sharing Content
3.
Begin casting from your AirPlay- or Miracast-certified device.
For casting information for your device, refer to the product documentation.
4.
If prompted, enter the security code shown on the Home screen.
Share Content Using an HDMI Connection
Share content from your device through an HDMI connection. This method doesn’t require you to connect using a wireless service.
Procedure
» Connect your device to the video system’s HDMI input port.
Your HDMI content displays until you disconnect your device. If you restart the video system while your device is connected, the HDMI content is still there following the reboot.
Sharing Content on a Blackboard or Whiteboard
Blackboards and whiteboards provide blank canvases to write on so you can share your ideas and collaborate with others.
Note: The Blackboard button only displays if a mouse or touchscreen is connected to the system.
Add a Blackboard or Whiteboard
You can create a blackboard or whiteboard at any time.
Note: If the active board has no annotations, you can’t add a new board.
A limited number of blackboards or whiteboards are available. A prompt notifies you when you have reached the limit.
Procedure
1.
Do one of the following:
▪ Out of a call: On the Home screen, select Blackboard .
▪ In a call: Select Menu > Content > Blackboard .
2.
To add another board, do one of the following:
▪ To add a blackboard: In the toolbar, select Blackboard .
▪ To add a whiteboard: In the toolbar, long press Blackboard and select Whiteboard .
Note: The default board type is whatever type you last selected.
Take a Snapshot of Your Content
You can take a picture of your current content. Then you can annotate on the snapshot or download it using the Polycom Content App.
24
Sharing Content
A limited number of snapshots are available. A prompt notifies you when you have reached the snapshot limit.
Procedure
» With a board or content on the screen, select Snapshot .
The system captures the content and displays it as Snapshot-1 . The system names additional snapshots with successive numbers.
Delete Snapshots or Content
You can delete snapshots or content that you no longer need.
Procedure
1.
Select a snapshot or piece of content in the content tray.
2.
Select the red X .
3.
Select Delete .
End a Content Session
By ending the content session, you stop showing and delete all content shared on your system.
Procedure
1.
During a content session, select Menu > End Session .
A message displays a warning and a countdown timer.
2.
Select End Session .
Note: To keep content, select Continue Session .
End a Call with Blackboard or Whiteboard Content
If there’s an open blackboard or whiteboard in your call (including drawings, markup, snapshots, or even a blank board), you can keep that content session going after hanging up. (Markup doesn’t include highlights.)
Procedure
1.
In a call with blackboard or whiteboard content, select Menu > Hang Up .
The call ends and the system prompts if you want to keep content.
2.
Do one of the following:
▪ Select Yes, Keep Content .
▪ Select No, End Session .
If you keep content, the content session continues.
3.
When you are ready to stop content, select Menu > End Session > End Session .
25
Cameras
Topics:
▪
▪
▪
▪
Turn Camera Tracking On or Off
▪
▪
Camera controls are available in and out of calls.
You can control cameras, depending on the camera type, in the following ways:
▪ Adjust an in-room camera
▪ Adjust a far-site camera
▪ Turn your camera on or off
▪ Turn camera tracking on or off
▪ Select, save, or delete presets
Adjust an In-Room Camera
To enhance the view of meeting participants, make adjustments to the in-room camera.
If camera tracking is on, camera control is unavailable. Turn tracking off to access camera controls.
With the Studio X50 and Studio X30 systems, you can’t pan or tilt the camera if it’s zoomed all the way out.
Procedure
1.
Select Menu > Camera .
2.
Select Control .
3.
Press + to zoom in or to zoom out. Press the arrows to tilt up and down or to pan left to right.
4.
To exit the control screen, select Back .
Adjust a Far-Site Camera
To enhance your view of the other meeting participants during a call, you can adjust the far-site camera.
If camera tracking is on, camera control is unavailable. Turn tracking off to access camera controls.
Note: Contact your administrator for help setting up this feature.
26
Cameras
Procedure
1.
Select Menu > Camera .
2.
Select Control .
3.
Select Switch to select the Far camera.
4.
Press + to zoom in or to zoom out. Press the arrows to tilt up and down or to pan left to right.
5.
To exit the control screen, select Back .
Turn Your Camera On or Off
You can turn your camera on to show local video or turn your camera off to hide your local video.
Procedure
1.
Select Menu > Camera .
2.
Select Camera On or Camera Off .
Turn Camera Tracking On or Off
When camera tracking is on, the camera automatically frames the group of people in the room or the current speaker (depending on your camera and how your system is configured).
Note: If you mute your local microphone, the system disables speaker tracking.
Procedure
1.
Select Menu > Camera .
2.
Select Tracking On or Tracking Off .
Using Camera Presets
If your camera supports presets, you can save up to 10 camera positions. Camera presets are stored camera positions that let you quickly point a camera at predefined locations in a room.
Near camera presets are available in or out of a call. Far camera presets are only available during a call.
If enabled, you can use them to control the far-site camera.
When you save a preset, the preset saves the selected camera and the camera position.
Note: If camera tracking is on, camera controls and presets are unavailable. Turn tracking off to access these features.
Save a Camera Preset from the Local Interface
Save the current camera position as a preset for later use.
Use saved presets to change the near camera position in or out of a call. Far camera presets are available only in a call.
27
Cameras
Procedure
1.
Select Menu > Camera .
2.
Select Presets .
3.
Adjust the camera to the desired position.
4.
Do one of the following:
▪ On the screen, select an empty preset.
▪ On the screen, long press the preset and choose Save .
▪ On the remote control, press a number to select a preset.
Select a Preset
Using previously created camera presets, you can quickly move the camera to a desired position in a call.
Procedure
1.
Select Menu > Camera .
2.
Select Presets .
3.
Do one of the following:
▪ Select the image of the preset you want.
▪ On the screen, long press the image and choose Select .
▪ On the remote control, press a number to select a preset.
Delete a Preset
You can delete a camera preset that you no longer need.
Procedure
1.
Select Menu > Camera .
2.
Select Presets .
3.
On the screen, long press the preset image you want to delete.
4.
Select Delete .
Selecting the Primary Camera
In Poly Video Mode, if you have more than one camera attached to the system, you can select the primary camera in or out of a call.
Camera Priority
When you connect or disconnect a camera, camera priority determines the primary or active camera.
▪ When you attach a camera to a system that’s powered on, it automatically becomes the current people camera.
▪ If you attach a camera during a call, it automatically becomes the current people camera.
▪ If you disconnect the current people camera, the system falls back to the next priority camera.
The system observes the following camera type priority:
28
Cameras
1.
Embedded camera
2.
HDCI camera
3.
USB camera
4.
HDMI source set to display as people
Select the Primary Camera from the Local Interface
In Poly Video Mode, when you attach multiple cameras to the system, select the primary camera from the local interface.
Procedure
1.
Go to Menu > Camera > Select Camera .
2.
Select a camera from the list.
The selected camera becomes the primary camera.
29
Using the System as a Camera and
Audio Peripheral
Topics:
▪
▪
Connect a Windows or Mac Laptop
▪
▪
Disconnect a Windows or Mac Laptop
With Poly Device Mode, you can use a Poly video system as your laptop’s external camera, microphone, and speaker.
For example, instead of using your laptop’s camera for Microsoft Teams calls, you can connect the Studio
X30 and use its 4K camera that automatically follows the conversation in the room. You also gain a Poly echo-cancelling microphone and speaker technology during calls.
Once you connect the system to your laptop with a USB cable, you can control the video system’s camera and audio features using your laptop’s third-party conferencing application. Remember the following about audio controls:
▪ You can also mute audio using the buttons on any connected microphones.
▪ If you mute audio from your app, the video system and microphone LEDs indicate you’re muted
(and vice versa).
If needed, you can also mirror your laptop’s screen on the video system’s monitors with an HDMI cable.
Laptop and Cable Requirements
Make sure that your laptop and USB cable allow you to use a Poly video system as a camera and audio accessory (i.e., Poly Device Mode).
Your laptop must have one of the following operating systems:
▪ Windows 10 version 1803 or later
▪ macOS version 10.12 or later
Remember when choosing a USB cable:
▪ Use a cable with at least one USB-C connection for your video system.
▪ If possible, use a USB 3.0 cable to ensure connection reliability and video and audio quality. (You can also use a USB 2.0 cable.)
▪ If you need a connection that’s longer than 2 m (6.6 ft), use a self-powered USB booster extension cable.
▪ Don’t use a cable used only for charging devices.
30
Using the System as a Camera and Audio Peripheral
Connect a Windows or Mac Laptop
To use the video system as an external camera and audio accessory, you must enable Poly Device Mode and connect your laptop with a USB cable.
Note the following (contact your administrator if you need help):
▪ If your conferencing application uses echo cancellation, disable that feature.
▪ Poly Device Mode isn’t available if the video system’s USB ports are disabled.
▪ Use a cable with at least one USB-C connection for your video system.
Procedure
1.
On the Home screen, select Device Mode .
2.
Connect the USB cable to your laptop.
3.
Connect the USB-C end of the cable to the video system’s USB-C port.
4.
Optional: To mirror your laptop’s screen on a video system monitor, connect the laptop using the system’s HDMI input port.
Incoming Calls to the System
The video system rejects incoming calls in Poly Device Mode.
Disconnect a Windows or Mac Laptop
Any camera options you change on the video system with your USB-connected laptop revert to their previous settings when you exit Poly Device Mode.
Procedure
» Do one of the following:
▪ On the video system local interface or TC8 device (if you have one), select Exit Mode .
▪ Unplug the cables connecting your laptop and video system. After a couple minutes, you see the video system home screen.
31
Settings
Topics:
▪
▪
Before or during calls, you can adjust video and audio settings, including adjusting the volume and changing the video layout.
Video Adjustments
You can manage video and certain user interface settings.
Change the Participant Layout
During a call, you can change from the current layout to another layout better suited for the meeting. The layout frames include the near site and far site.
If you’re sharing content on a single monitor, content displays in one of the frames.
Procedure
1.
In a call, go to Menu > Layouts .
2.
Select one of the following layouts:
▪ Equal : All participants are the same size.
▪ Gallery : Participants display at the top of the screen and the speaker displays in the main frame.
▪ Fullscreen : The active speaker displays in full screen.
Audio Adjustments
You can control several audio settings on the system.
Mute Your Microphones
To prevent distractions for the speaker and meeting participants, you can mute your microphones.
You can mute your audio in or out of a call.
Procedure
» Do one of the following:
▪ On your remote control, press Mute .
▪ On the screen, select Menu > Mute .
A notification displays that the system muted your local microphones.
32
Settings
Unmute Your Microphones
When your audio is muted and you’re ready to speak in a call, unmute your microphones.
Procedure
» Do one of the following:
▪ On your remote control, press Mute
.
▪ On the screen, select Menu > Unmute .
Adjust the Volume
You can adjust the volume before or during a call.
Procedure
1.
Go to Menu > Volume .
2.
Do one of the following:
▪ Use the volume slider on a touchscreen.
▪ Press the + or buttons on the remote control.
▪ Press the left or right navigation buttons on the remote control (when the system displays volume control).
33
Troubleshooting
Topics:
▪
▪
▪
This section includes information related to troubleshooting issues with your system. You can also find information on pairing your remote, configuring your monitors, and where to find help tips.
Poly Device Mode
Use these topics to troubleshoot problems you may encounter using Poly Device Mode.
Audio Levels are Too High or Low
Symptom:
In Poly Device Mode, audio from the video system speakers is too loud or it’s difficult to hear call participants.
Problem:
In Poly Device Mode, your conferencing application and laptop control the video system’s audio. You may need to adjust those volume controls.
Workaround:
Follow these steps until you get the audio levels you want:
Procedure
1.
Adjust your conferencing application’s volume.
2.
Adjust your laptop’s volume.
Conferencing Application Doesn’t Use System Camera or Audio
Symptom:
You can’t use the video system’s camera or audio in Poly Device Mode.
Problem:
Your conferencing application by default may choose the connected monitor speakers instead of, for example, the Studio X50 speakers.
34
Troubleshooting
Workaround:
Procedure
» In your conferencing application, select the video system as your speaker, microphone, and camera device.
Can’t Use System’s Camera or Audio
Symptom:
You may notice the following while using Poly Device Mode:
▪ In your laptop’s conferencing application, you can’t select the video system as a camera or audio source.
▪ The video system’s camera and audio seem unavailable.
▪ The video system’s camera doesn’t display live video.
Problem
There could be a few reasons for these types of problems. For instance, your conferencing application by default may choose the connected monitor speakers instead of, for example, the Studio X50 speakers.
Workaround:
Follow these steps until you fix your problem:
Procedure
1.
In your conferencing application, select the video system as your speaker, microphone, and camera device.
2.
In your laptop settings, select the video system as your speaker, microphone, and camera device.
3.
Exit and restart Device Mode.
4.
Replug the USB cable.
5.
Connect the cable to a different USB port on your laptop.
6.
Try using a different USB cable.
7.
Restart your laptop.
Improve Audio Quality
Symptom:
Audio quality during calls in Poly Device Mode could be better. For example, people on the call notice interference or dropped words when you’re speaking.
Problem:
You may encounter these problems for the following reasons: additional USB connections, a bad cable, or audio processing settings.
Workaround:
Follow these steps until your audio quality improves:
35
Troubleshooting
Procedure
1.
Remove USB audio devices (such as a headset) connected to your laptop.
2.
Connect your laptop and video system with a different USB cable.
3.
If your conferencing application uses echo cancellation, disable that feature.
4.
If you’re playing a musical instrument, enable M-Mode in the system web interface.
Contact your administrator to set up this feature.
Improve Laptop Screen Mirroring
Symptom:
When mirroring your laptop screen with an HDMI connection, the picture on the connected monitor isn’t ideal.
Problem:
The resolution on your laptop may need to be adjusted for the monitor connected to the Poly video system.
Workaround:
Follow these steps until screen mirroring quality improves:
Procedure
1.
Adjust your laptop’s resolution settings.
2.
Adjust your laptop’s display settings so the screen duplicates on the monitor.
Can’t Share Wireless Content
Symptom:
You try sharing content wirelessly (for example, from an AirPlay-certifed device) but nothing happens.
Problem:
If your video system is in Poly Device Mode, you can’t share content wirelessly.
Workaround:
Once you exit Device Mode, you can share wireless content to the video system.
Procedure
» Do one of the following:
▪ On the video system local interface or TC8 device (if you have one), select Exit Mode .
▪ Unplug the cables connecting your laptop and video system. After a couple minutes, you see the video system home screen.
36
Troubleshooting
View Content Help Tips
Content help tips provide information on how to stream content using HDMI, the Polycom Content App, or an Airplay- or a Miracast-certified device.
Note: If you’re already connected to a source for sharing content, the help tips don’t display.
Procedure
1.
On the Home screen, select Content .
The help screen opens.
2.
Review the tips for your source type.
3.
To go back to the previous screen, select Back .
View Blackboard Help Tips
For help annotating on your blackboard or whiteboard, you can access information on how to use the annotation icons and touch gestures.
Procedure
1.
On the home screen, select Blackboard .
2.
On the toolbar, select Help .
The help screen opens.
3.
To close the screen, tap the screen or press Back on your remote control.
37
ダウンロード
広告