Projecta IS1210E, IS910E Manual

Add to My manuals
12 Pages

advertisement

Projecta IS1210E, IS910E Manual | Manualzz

LITHIUM EMERGENCY

JUMPSTARTER

AND PORTABLE POWER BANK

P/No. IS910E, IS1210E

1

IMPORTANT SAFETY INFORMATION

Please read this manual thoroughly before use and store in a safe place for future reference.

WARNINGS

• Risk of explosive gas. Working in the vicinity of a lead-acid battery can be dangerous.

Batteries release explosive gases during normal operation, charging and while jumpstarting a battery. Before using this Jumpstarter, read and follow the instructions carefully. Follow all manufacturer’s instructions and warnings on the vehicle’s battery and other equipment being used.

• Jumpstart 12V lead-acid batteries only. Do not use to jumpstart dry-cell batteries commonly found in household appliances. These batteries may burst and cause injury and/or property damage.

• Do not smoke, use matches, use a cigarette lighter, or allow a spark or flame near the battery.

• Do not allow metal to come in contact with the battery posts. It may spark or short circuit the battery and cause an explosion/fire.

• Always wear eye protection when operating the Jumpstarter.

• Remove rings, bracelets, necklaces and watches when working with a lead-acid battery.

• Contains a Lithium Cobalt battery and must be disposed of properly.

• Ensure correct polarity when connecting to vehicle.

• Although the Jumpstarter is rain proof it is not designed to be left outside for extended periods or submerge in water.

• Although the Jumpstarter has been designed to protect the battery it is best to not drop the Jumpstarter or try and pierce the Jumpstarter in anyway, as this can result in a fire.

If the Jumpstarter is physically damaged in any way do not use.

• Do not store the Jumpstarter in temperatures above 40 o Celsius or below -10 o this can affect the health of the battery and if the temperature is above 120 battery may catch fire.

o

Celsius, as

Celsius the

• Not intended for people (including children) with reduced physical or mental capability.

• Once the vehicle is started disconnect the Jumpstarter immediately after starting.

• Do not try and charge via the USB output as this will damage the Jumpstarter and the

USB output.

IMPORTANT CHARGING INFORMATION

• Charge Jumpstarter prior to first use, this may take up to 4 to 8 hours depending on the model.

• Fully recharge the Jumpstarter after every use to ensure your Jumpstarter is ready in emergencies.

• To extend the life of your battery do not let the battery charge level fall below 20%.

• To extend the life of the Jumpstarter battery, do not charge above 45 o C or below 0 o C.

2

FEATURES

IS910E

The IS910E is suitable for starting most 12V Petrol vehicles up to 6 litres.

IS1210E

The IS1210E is suitable for starting most 12V Petrol vehicles up to 7 litres and diesel vehicles up to 3.2 litres.

12V USB CHARGING – Allowing the Jumpstarter to be charged from your vehicle cigarette socket.

LITHIUM BATTERY – Increased storage life and a much more compact lightweight unit.

PREMIUM SPARK FREE CLAMPS – Ensuring safe Jumpstarting.

INCORPORATING HIGHEST RATE OF DISCHARGE BATTERY – For increased starting capacity.

POWER BANK WITH 2.1AMP USB PORT – Allowing charging of phones, tablets and other small portable devices.

EASY TO READ BATTERY STATUS INDICATOR – Shows battery status and when recharge is required.

CONNECTION INDICATION – Confirms clamp connectivity and status.

INBUILT LED FLOOD LIGHT – Inbuilt LED flood light provides illumination for safer, more convenient operation at night.

ADDED PROTECTION, SAFETY AND RELIABILITY

TOTAL SAFEGUARD PROTECTION – Includes Over voltage Protection, Battery &

Switch Over-temperature Protection, Short Circuit Protection, Over Current Protection,

Over Cranking Protection, Under-voltage Protection, Low voltage indication, Battery Cell

Balancing to protect the user, vehicle and Jumpstarter.

SMART MODULE – A second layer of protection, preventing the unit from over charging.

REVERSE POLARITY PROTECTION & ALARM – Prevents sparking from accidental reverse connection. The alarm sounds when the Jumpstarter clamps are connected incorrectly.

SURGE PROTECTION – IS910E/IS1210E features built in surge protection so you can safely Jumpstart vehicles with EFI (electronic fuel injection) and computer management systems.

3

SPECIFICATIONS

Part No.

Battery

Battery Type

Voltage

Battery Capacity

Peak Amps

Clamp Power

Number of Jumpstarts

(vehicle without a battery)

Number of Emergency Jumpstarts*

(with a flat vehicle battery)

Battery Cycles

USB Output

USB output

USB low Voltage Disconnect

Jumpstarter Leads

Length

Cable

Polarity Protection

Overload Protection

Recharging

Cable

Micro USB Charging port

12V DC charging

Recharge time

Jumpstart Connection Voltages

Vehicle Voltage Range

Dimensions, Weight & Environmental

Height

Width

Depth

Weight

Operating Temperature

Storage Temperature

Ingress Protection

IS910E

900A

240A

IS1210E

Lithium Cobalt (LiCo)

12 Volt only

6,600mAhr at 3.7V

24.4wHr at 3.7V

2.2Ahr at 12.0V

7 Starts (Petrol)

0 Starts (Diesel)

14 Starts (Petrol)

0 Starts (Diesel)

500

13,500mAhr at 3.7V

50.0wHr at 3.7V

4.5Ahr at 12.0V

1200A

330A

14 Starts (Petrol)

0 Starts (Diesel)

28 Starts (Petrol)

5 Starts (Diesel)

500

2.1A, 5.0V

Battery voltage at 9.0V

Positive 23.5cm, Negative 16.5cm

8mm² 8(AWG)

MCU controlled with Electronic Switch Smart Module

MCU controlled with Electronic Switch Smart Module

1m long USB to Micro USB

2.1Amp micro USB charging port

3rd party 10W 240VAC USB adaptors can be used. (Not Provided)

12V to 5V 2.1Amp USB charger (provided)

4 hours 8 hours

0~15.0V

0.61Kg

47mm

178mm

91mm

0.76Kg

0 to 45°C

-20 to 40°C

IP52 (Rain Proof) with covers over the ports

* Tested on a Ford Ranger 3.2L Diesel and Ford Territory 4.0L Petrol with a flat battery in good condition

4

PRODUCT OVERVIEW

Premium Spark

Free Clamps

Jumpstarter

Charging Port

Durable Padded

Carry Case

2.1A USB

Accessory port

Battery Status

Indicator

Clamp

Connection LED

Battery

Clamps

Connection

Port

Smart

Module

Micro USB

Charging Lead

Flood Light

On/Off

On/Off

12V 2.1A USB Charging

Plug Adaptor

Jump Start

Button

2 x 0.5 Watt

LED Flood Light with SOS Function

5

VEHICLE JUMPSTARTING INSTRUCTIONS

1. Your Jumpstarter should be charged for 8 hours prior to first use and as soon as possible after each use.

2. Before making any connections, check the Jumpstarter battery status by turning on the

Jumpstarter. The Jumpstarters battery capacity should show at least 2 bars or 50%

charged.

3. Turn your vehicle’s ignition OFF before connecting the Jumpstarters clamps to your vehicle.

4. Connect the Red Positive (+) clamp to the positive (+) terminal of the battery in the vehicle and the Black Negative (-) clamp to the negative (-) terminal of the battery or any non moving metal part of the engine block. DO NOT CONNECT TO FUEL LINE.

Always double check that you have the proper connections.

5. Press and hold the Jump Start button for 1 second. The Clamp LED should turn on to Green.

6. Turn the vehicle’s ignition to ON and start the vehicle. After the engine has started, turn the Jumpstarter off. If the Jumpstarter fails to start your vehicle refer to the

Clamp Connection LED table below for any error it may indicate & check that the clamps are correctly connected with good contact.

7. Disconnect the Black clamp and then the Red clamp.

8. Recharge the Jumpstarter.

UNDERSTANDING YOUR JUMPSTARTER

CLAMP CONNECTION LED

Jumpstart Status LED State

Jumpstarter clamps connected to vehicle and ready to jumpstart Green Solid

Jumpstarting for more than 5 seconds 2 x Yellow Flash, pause & repeat

Battery or Jumpstarter switch, Over-temperature

Battery Charging in Temperatures >60°C or <0°C

Short Circuit

Red/Green Alternate flashing

Red/Green Alternate flashing and Siren

Red Flashing &

Beeping Siren

Clamps reverse connected to battery

Jumpstarter is connected to vehicle battery and the Smart

Module has failed. Go to store to get P/n: ISECLAMP.

Jumpstarter is not connected to a vehicle battery.

Jumpstarter has an internal fault and can not be used.

Red Solid and

Siren on

Red fast flash, Siren

Steady on

Red fast flash, Siren

Steady on

6

BATTERY STATUS INDICATOR

When Jumpstarter is turned on battery gauge LED’s are displayed.

State of Charge

<20%

Battery Gauge LED Display

– Red Flashing

20–25%

25–50%

50–75%

75–100%

– Red

– Yellow

– Green

– Green

The Jumpstarter will beep if less than 10.0V until charged or turned off.

CHARGING THE JUMPSTARTER

The Jumpstarter can be charged with the provided 12V DC to USB charge adaptor or a via

3rd party 10 Watt USB 240VAC charger (tablet charger).

1. Plug the 12V to 2.1A USB charge adaptor into a 12V socket.

2. Use the provided USB to micro USB cable: a. Connect the USB end into the 12V to USB socket.

b. Connect the micro USB end to the Jumpstarter.

The Jumpstarter will now turn on and start charging. The BATTERY STATUS INDICATOR will now start to scroll in the following ways depending on its state of charge.

State of Charge

<20%

20–50%

50–75%

75–99%

100%

Battery Gauge LED Display

– All Flashing

– Red with Yellow & Green Flashing

– Yellow with Green Flashing

– Green with Green Flashing

– All Solid Green

3. When your Jumpstarts is fully changed after 4 hours for IS910E or 8 hours for

IS1210E, simply disconnect the leads and put the Jumpstarter away.

7

WHEN TO CHARGE

Your Jumpstarter is shipped partially charged. Therefore you should charge the Jumpstarter before using it for the first time. It is recommended to charge fully after each use so the

Jumpstarter is ready in case it is required.

POWER BANK

The Jumpstarter has a USB output with 2.1A out. It is suitable to charge phones, tablets, cameras and GPS devices. The Jumpstarter will turn off after 5 minutes of no activity or the USB device has been fully charged.

If the USB output becomes overloaded, remove the device and check it. Turn the

Jumpstarter off and back on again, the USB output should work again

WARNING: Charging devices from the Jumpstarter will drain the battery and potentially cause the Jumpstarter to fail to start your vehicle in an emergency. Recharge the

Jumpstarter as soon as possible.

FLOOD LIGHT

The Flood light has two functions, Flood light mode and SOS mode.

Flood light mode

Press and hold the light button for less than 3 seconds and the light will turn on. Press the

Light button again to turn the light off when you are finished.

Note: If the Jumpstarter is off and the light button is pressed, the button will need to be pressed for at least ½ second before the light will turn on.

SOS mode

Press and hold the light button for more than 3 seconds and the work light will now transmit SOS in Morse code. Press the light button again to turn off.

Note: The Flood light is not on a timer and will continue to operate until the battery is flat.

8

FREQUENTLY ASKED QUESTIONS

Q. Why didn’t my Jumpstarter start my vehicle?

A. There could be a number of reasons why the Jumpstarter did not start you vehicle.

Check the following:

1. Ensure the Jumpstarter battery is fully charged. Refer to page 7 (“BATTERY STATUS

INDICATOR”) for further information.

2. Ensure you have followed the correct operating procedure. Refer to page 5

(“Vehicle Jumpstarting Instructions”).

3. Ensure the vehicle operates on 12V DC

4. Ensure the vehicle being jumpstarted does not require a clamp output greater than

240 Amps (IS910E) or 330 Amps (IS1210E) in order to jumpstart the vehicle.

Q. Can I leave my Jumpstarter connected to car after it has started?

A. No. The Jumpstarter is not a replacement battery and should be disconnect from the vehilce battery after the engine has started. Once the engine has started the jumpstarter has already internally disconnected so the jumpstarter is not providing any benefit to the vehicle and is best packed away so the jumpstarter does not fall into the engine or moving parts.

Q. How often should I charge my Jumpstarter?

A. The Jumpstarter uses Lithium technology which self discharges only a very small amount.

To be safe the Jumpstarter should be charged at least every year to be sure it is ready in case of an emergency.

Q. Can I charge the Jumpstarter and use the USB output at the same?

A. Yes that will not be a problem.

Q. What is Peak Amps?

A. Peak amps is the maximum current the battery in the Jumpstarter can produce.

Q. What is Clamp Power?

A. Clamp power is the maximum current available at the clamps.

Q. What is the Smart Module?

A. The Smart Module prevents the unit from overcharging and creates a second layer of protection.

9

NOTES

10

NOTES

11

WARRANTY STATEMENT

Brown & Watson International Pty. Ltd. (“BWI”) of 1500 Ferntree Gully Road, Knoxfield,

Vic., telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue will under normal use and service be free of failures in material and workmanship for a period of one (1) year from the date of the original purchase by the customer as marked on the invoice (see elsewhere for specific warranty period). This warranty does not cover ordinary wear and tear, abuse, alteration of products or damage caused by the purchaser.

To make a warranty claim the consumer must deliver the product at their cost to the original place of purchase or to any other place which may be nominated by either BWI or the retailer from where the product was bought in order that a warranty assessment may be performed. The consumer must also deliver the original invoice evidencing the date and place of purchase together with an explanation in writing as to the nature of the claim.

In the event that the claim is determined to be for a minor failure of the product then

BWI reserves the right to repair or replace it at its discretion. In the event that a major failure is determined the consumer will be entitled to a replacement or a refund as well as compensation for any other reasonably foreseeable loss or damage.

This warranty is in addition to any other rights or remedies that the consumer may have under State or Federal legislation.

IMPORTANT NOTE

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Distributed by

AUSTRALIA

Brown & Watson International Pty Ltd

Knoxfield, Victoria 3180

Telephone (03) 9730 6000

Facsimile (03) 9730 6050

National Toll Free 1800 113 443

NEW ZEALAND

Narva New Zealand Ltd

22–24 Olive Road

PO Box 12556 Penrose

Auckland, New Zealand

Telephone (09) 525 4575

Facsimile (09) 579 1192

IS351

Issue 2 23.11.18

advertisement

Related manuals

advertisement