Matrix CONNEXUS GFTFS Assembly Instructions Manual

Add to My manuals
26 Pages

advertisement

Matrix CONNEXUS GFTFS Assembly Instructions Manual | Manualzz

CONNEXUS

GFTFS

GFTWM

GFTEXP

GFTLM

GFTMB

GFTVRT

GFTCB

GFTHB

2

3 ENGLISH

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

XX LANGUAGE

IMPORTANT SAFETY INFORMATION

It is the sole responsibility of the purchaser of MATRIX products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment.

It is recommended that all users of MATRIX exercise equipment be informed of the following information prior to its use.

Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX equipment be used properly to avoid injury.

PROPER USAGE

1. Do not exceed weight limits of the exercise device.

2. If applicable, set safety stops to appropriate height.

3. If applicable, adjust seat pads, leg pads, foot pads, range of motion adjustment, or any other type of adjustment mechanisms to a comfortable start position. Make certain that the adjusting mechanism is fully engaged to prevent unintentional movement and to avoid injury.

4. Sit on bench (if applicable) and get into appropriate position for exercise.

5. Exercise using no more weight than you can safely lift and control.

6. In a controlled manner, perform exercise.

7. Return weight to its fully-supported start position.

INSTALLATION

1. STABLE AND LEVEL SURFACE: MATRIX exercise equipment must be installed on a stable base and properly leveled.

2. SECURING EQUIPMENT: Manufacturer requires that all stationary Matrix Connexus equipment be secured to the floor to stabilize equipment and eliminate rocking or tipping over. This must be performed by a licensed contractor.

Floor anchor points must be able to withstand 750 lbs. (3.3 kN) pull-out force.

Wall anchor points must be able to withstand 500 lbs. (2.2 kN) pull-out force.

Please contact your Matrix Representative for Connexus anchoring guidelines.

ADDITIONAL NOTES

This equipment should only be used in supervised areas where access and control is specifically regulated by the owner. It is up to the owner to determine who is allowed access to this training equipment. The owner should consider a user’s: degree of reliability, age, experience, etc.

This training equipment meets industry standards for stability when used for its intended purpose in accordance with the instructions provided by the manufacturer.

This equipment is for indoor use only. This training equipment is a Class S product (designed for use in a commercial environment such as a fitness facility). This training equipment is in compliance with EN ISO 20957-1.

WARNING

DO NOT USE equipment if not properly secured to floor.

Manufacturer requires that this equipment be secured to the floor to stabilize and eliminate rocking or tipping over.

Use a licensed contractor.

WARNING

DEATH OR SERIOUS INJURY CAN

OCCUR ON THIS EQUIPMENT. FOLLOW

THESE PRECAUTIONS TO AVOID

INJURY!

1. Keep children under the age of 14 away from this strength training equipment. Teenagers must be supervised at all times while using this equipment.

2. This equipment is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the equipment by a person responsible for their safety.

3. All warnings and instructions should be read and proper instruction obtained prior to use.

Use this equipment for its intended purpose ONLY.

4. Inspect the machine before use. DO

NOT use machine if it appears damaged or inoperable.

5. Do not exceed weight capacity of this equipment.

6. Where applicable, use retention devices to retain weight discs.

7. Injuries to health may result from incorrect or excessive training.

Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program.

8. Keep body, clothing, hair, and fitness accessories free and clear of all moving parts.

9. Horizontal adjustable bars are heavy. Support bars from center of mass when detaching and reattaching bar to frame structure.

Ensure bar is fully engaged with frame before use.

10. If optional heavy bag is used, do not support body weight from the bag. Do not add additional weight to bag.

11. When adjusting any adjustable mechanism (stop position, seat position, pad location, range of motion limiter, pulley carriage, or any other type), make certain that the adjustable mechanism is fully engaged prior to use to prevent unintended motion.

12. Manufacturer requires that this equipment be secured to the floor to stabilize and eliminate rocking or tipping over. Use a licensed contractor.

13. DO NOT REMOVE THIS LABEL.

REPLACE IF DAMAGED OR

ILLEGIBLE.

Group Functional Trainer

3

4

MAINTENANCE

1. DO NOT use any equipment that is damaged and or has worn or broken parts.

Use only replacement parts supplied by your country’s local MATRIX dealer.

2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information. If unreadable or missing, contact your MATRIX dealer for a replacement.

3. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.

4. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX dealers will provide service and maintenance training at our corporate facility upon request.

WARRANTY

For North America, please visit www.matrixfitness.com for warranty information along with warranty exclusions and limitations.

MAINTENANCE CHECKLIST

ACTION

Inspect ROM

FREQUENCY

Daily

Inspect Hardware/Pull pins

Inspect Frame

Clean Machine

Monthly

Monthly

As Needed

Clean Grips * As Needed

* Grips should be cleaned with a mild soap and water or a non-ammonia based cleaner.

PRODUCT SPECIFICATIONS

Max User Weight

Product Weight

GFTFS

Group Functional Trainer

FREE STANDING

GFTWM

Group Functional Trainer

WALL MOUNTED

159 kg / 350 lbs. Maximum 2 users per station

313 kg / 690 lbs.

218 kg / 481 lbs.

GFTEXP

Group Functional Trainer

EXPANSION

171 kg / 377 lbs.

GFTLM

Landmine

Attachment

4 kg / 9 lbs.

Overall Dimensions

(L x W x H)*

Recommended

Training Area

291 x 265 x 242 cm /

115 x 104.5 x 95”

830 x 820 cm /

326.5” x 323”

275 x 158 x 242 cm /

108.5 x 62.5 x 95”

630 x 450 cm /

248.5” x 177.5”

260 x 158 x 242 cm /

102.5 x 62.5 x 95”

Adds 240 cm / 96” to length of wall-mounted footprint

36 x 13 x 10 cm /

14 x 5 x 4”

* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX strength equipment.

Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.

GFTMB

Med Ball Target

GFTCB

Magnetic Chalkboard

50 kg / 110 lbs.

193 x 86 x 13 cm /

76 x 34 x 5”

26 kg / 57.5 lbs.

109 x 60 x 17 cm /

43 x 24 x 7”

UNPACKING

Thank you for purchasing a MATRIX Fitness product. It is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully unpack the unit from this box and dispose of the packing materials in accordance with your local laws.

CAUTION

To avoid injury to yourself and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment on a stable base, and properly level the machine. Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around

MATRIX strength equipment. Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.

TOOLS REQUIRED FOR ASSEMBLY (not included)

3MM L-Shaped Allen Wrench

4MM L-Shaped Allen Wrench

5MM L-Shaped Allen Wrench

6MM L-Shaped Allen Wrench

8MM L-Shaped Allen Wrench

10MM L-Shaped Allen Wrench

Phillips Screwdriver

8MM Open-End Wrench

17MM Open-End Wrench

Guide Rod Lubrication

If any items are missing please contact your country’s local MATRIX dealer for assistance.

0

mm

10 20 30 40 50 60 70 80 90 100 110 120 130

* Use Vibra-Tite 135 Red Gel Threadlocker where nylock nuts are not used.

5

B x12

GFTFS

Free Standing

A x8 A x28

D x4

SQ

1

FT

TOTAL TRAINING AREA

8.3 × 8.2

M

(27.2 × 26.9

FT

)

C x40

6

A x8

GFTFS Torque Values

A M10 Torque to 77 Nm/57 ft-lb

B M10 Torque to 40 Nm/30 ft-lb

C M8 Torque to 39 Nm/29 ft-lb

D M6 Torque to 17 Nm/147 in-lb

B x8 C x8

FREE-STANDING

DIMENSIONS

2.9 × 2.8

M

(9.5 × 9.2

FT

)

TRAINING AREA

2.7

M

(8.9

FT

)

WIDE PATH

FREE AREA

0.6

M

(2

FT

)

WIDE PATH

Z27x2

Z13

Z05x2

Z11

Z27x2

Z13

Z05x2

Z11

Z11

Z05x2

Free Standing

Step 1 of 3

Z13

Z27x2

Z13

Z05x2

Z11

Z27x2

GFTFS

NOTE:

Assemble laying down for step 1

Do not completely tighten hardware until final step

Item

Z05

Z11

Z27

Z13

Description

Flat Washer (Φ10)

Screw (M10x110L)

Screw (M10x40L)

Nut (M10)

Qty

8

4

8

4

7

8

Z26x2

GFTFS

Free Standing

Step 2 of 3

Z26x2

Z13x2

Z13x2

Z26x2

Z24x2

Z05x4

Z13x2

Z13x2

Z24x2

Z05x4

Z05x4

Z24x2

Z26x2

Z05x4

Z24x2

NOTE:

Do not completely tighten hardware until final step

Item

Z26

Z05

Z24

Z13

Description

Screw (M10x75L)

Flat Washer (Φ10)

Screw (M10x155L)

Nut (M10)

Qty

8

16

8

8

Free Standing

Step 3 of 3

Z01

Z06x2

Z01

Z25x2

Z05x2

Z25x2

Z05x2

Z27x2

Z05x2

Z01

Z27x2

Z05x2

Z06x2

Z01

Z25x2

Z05x2

Z06x2

Z25x2

Z05x2

NOTE:

Tighten hardware from steps 1–3 using the following Torque Values on page 6.

Item

Z06

Z05

Z27

Z25

Z01

Description

Screw (M8x25L)

Flat Washer (Φ10)

Screw (M10x40L)

Screw (M10x25L)

Screw (M6x15L)

Qty

8

12

4

8

4

Z06x2

GFTFS

9

B x12

GFTWM

Wall Mounted

A x6 A x16

D x2

SQ

1

FT

C x20

WALL-MOUNTED

DIMENSIONS

2.7 × 1.7

M

(8.9 × 5.6

FT

)

TRAINING AREA

FRONT:

2.8

M

(9.2

FT

)

SIDES:

1.8

M

(5.9

FT

)

FREE AREA

0.6

M

(2

FT

)

10

A x8 C x8

GFTWM Torque Values

A M10 Torque to 77 Nm/57 ft-lb

B M10 Torque to 40 Nm/30 ft-lb

C M8 Torque to 39 Nm/29 ft-lb

D M6 Torque to 17 Nm/147 in-lb

B x4

Z27x2

Z13

Z05x2

Z11

Z13

Z05x2

Z11

Wall Mounted

Step 1 of 3

Z27x2

GFTWM

Item

Z05

Z11

Z27

Z13

Description

Flat Washer (Φ10)

Screw (M10x110L)

Screw (M10x40L)

Nut (M10)

Qty

4

2

4

2

NOTE:

Assemble laying down for step 1

Do not completely tighten hardware until final step

11

12

GFTWM

Wall Mounted

Step 2 of 3

Z12x2

Z24x2 Z05x4

Z13x2

Z24x2

Z05x4

Z13x2

Z13x2

Z05x2

Z26x2

Z28x2

Z13x2

Z05x4

Z24x2

Item Description

Z26

Z05

Z24

Screw (M10x75L)

Flat Washer (Φ10)

Screw (M10x155L)

Z13

Z12

Z28

Nut (M10)

Screw (M10x95L)

Screw (M10x90L)

Qty

2

18

8

10

2

2

NOTE:

Do not completely tighten hardware until final step

Z13x2

Z05x4

Z24x2

Z01

Z27x2

Z05x2

Z05x2

Z01

Z27x2

Wall Mounted

Step 3 of 3

GFTWM

Item

Z06

Z05

Z27

Z25

Z01

Description

Screw (M8x25L)

Flat Washer (Φ10)

Screw (M10x40L)

Screw (M10x25L)

Screw (M6x15L)

NOTE:

Tighten hardware from steps 1–3 using the following Torque Values on page 10.

Qty

8

4

2

8

4

Z06x4

Z06x2

Z25x2

Z05x2 Z05x2

Z25x2

Z06x2

13

14

GFTEXP

Expansion

SQ

1

FT

WALL-MOUNTED

DIMENSIONS (EACH)

2.4 × 1.7

M

(8 × 5.6

FT

)

TRAINING AREA

FRONT:

2.8

M

(9.2

FT

)

SIDES:

1.8

M

(5.9

FT

)

FREE AREA

0.6

M

(2

FT

)

Blue represents existing wall-mount

Expansion

Step 1 of 5

GFTEXP

NOTE:

Starting as wall-mounted unit GFTWM

Do not completely tighten hardware until final step

15

16

GFTEXP

Expansion

Step 2 of 5

Remove existing wall-mounted upright

Replace existing wall-mounted upright with expansion kit upright

NOTE:

Do not completely tighten hardware until final step

Z27x2

Z13

Z05x2

Z11

Existing wall-mounted upright

Z11

Z13

Z05x2

Expansion

Step 3 of 5

GFTEXP

Z27x2

Item Description

Z05

Z11

Z27

Z13

Flat Washer (Φ10)

Screw (M10x110L)

Screw (M10x40L)

Nut (M10)

Qty

4

2

4

2

NOTE:

Do not completely tighten hardware until final step

Assembly laying down for step 3.

17

18

GFTEXP

Z05x4

Expansion

Step 4 of 5

Z13x2

Z24x2

Z24x2

Z05x4 Z13x2

Z26x2

Existing wall-mounted upright placed at end of expansion

Z13x2

Z12x2

Z05x4

Item Description

Z26

Z05

Z24

Z13

Z12

Screw (M10x75L)

Flat Washer (Φ10)

Screw (M10x155L)

Nut (M10)

Screw (M10x95L)

Qty

2

16

8

8

2

Z24x2

NOTE:

Do not completely tighten hardware until final step

Z05x4

Z24x2

Z13x2

Existing installed wall-mount

Z06x4

Z27x2

Z05x2

Z01

Z05x2

Z05x2

Z25x2

Z06x2

Z06x2

Z25x2

Expansion

Step 5 of 5

GFTEXP

Item Description

Z06

Z05

Z27

Z25

Z01

Screw (M8x25L)

Flat Washer (Φ10)

Screw (M10x40L)

Screw (M10x25L)

Screw (M10x15L)

NOTE:

Tighten hardware from steps 1–3 using the following Torque Values on page 10.

Qty

2

4

8

6

1

19

20

GFTLM

Landmine Attachment

1

Item Description

Z14 Screw (M6x4L)

Qty

1

NOTE:

Tighten hardware from step 3 using the following Torque Value :

M6 17 Nm / 147 in-lb

3 Z14

Z06x2

Z15x3

2 Item

Z06

Z15

Description

Screw (M8x25L)

Screw (M8x16L)

NOTE:

Tighten hardware from step 2 using the following Torque Value :

M8 39 Nm / 29 ft-lb

Qty

2

3

Z20x2

Z20x2

Item Description

Z20 Hex Screw (M10x20L)

Qty

4

NOTE:

Tighten hardware from step 1 using the following Torque Value :

M10 40 Nm / 30 ft-lb

Med Ball Target

GFTMB

21

22

GFTVRT

Vertical Extension

1

SLIDE ROM DOWN

2

For use with the Free Standing unit only.

3

Item Description

Z05 Flat Washer (Φ10)

Z04 Screw (M10x35L)

Qty

2

2

NOTES:

Start with the top fastener, working down, tightening each bolt two or three revolutions at a time. Repeat process from top to bottom until all hardware is fully threaded.

Tighten hardware from step 3 using the following Torque Value :

M10 40 Nm / 30 ft-lb

Z05x2

Z04x2

Item

Z05

Z24

Z13

Description

Flat Washer (Φ10)

Screw (M10x155L)

Nut (M10)

Qty

4

2

2

NOTE:

Tighten hardware from step 1 using the following Torque Value :

M10 77 Nm / 57 ft-lb

1

Z13x2

Z05x4

Z24x2

Magnetic Chalkboard

GFTCB

Item

Z20

Description

Hex Screw (M10x20L)

Qty

2

NOTE:

Tighten hardware from step 2 using the following Torque Value :

M10 40 Nm / 30 ft-lb

2

Z20x2

23

24

1

GFTHB

Heavy Bag

2

3

4

Heavy bag not included

25

CONNEXUS - GFTFS / GFTWM / GFTEXP / GFTLM / GFTMB / GFTVRT / GFTCB / GFTHB

© 2015 Johnson Health Tech

Part # XXXXXXXXXX

Rev 1.2

advertisement

Related manuals

advertisement