INSTALLATION

INSTRUCTIONS

PARTS LIST

Cargo net

Accessory

CARGO NET

P/N: 08L96-TA0-100

Application

2010 ACCORD

4-DOOR

4-Door Template A

2-Door Template B (Not used)

2 Large anchors

2-Door Template C (Not used)

8 Small anchors

Accessory User’s Information Manual

Publications No.

AII 42259

Issue Date

AUG 2009

4 Stud bolts

4 Rivet nuts

6 Hex bolts, 6 x 16 mm

2 Flange nuts , 6 mm

8 Plain washers , 6 mm

4 Spring washers , 6 mm

2 Spacers

TOOLS AND SUPPLIES REQUIRED

Clip remover

Rivet nut tool (T/N: 07AAE-000A100)

Hex wrench

27 mm wrench

Drill

3 mm, 6.5 mm, 8 mm, 9 mm, and 11 mm Drill bits

Eye protection

Pushpin

Round file

Center punch

Masking tape

Tape

Touch-up paint

Torque wrench

© 2009 American Honda Motor Co., Inc. – All Rights Reserved.

AII 42259 (0908) 08L96-TA0-1000-91

1 of 7

INSTALLATION

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by

“do-it-yourselfers.”

1.

Remove the trunk floor mat (one clip).

CLIP

TRUNK

FLOOR MAT

3.

Remove the left trunk side trim panel (five clips).

LEFT TRUNK

SIDE TRIM

PANEL

3 CLIPS

7109070E

2.

Remove the rear trunk trim panel (four clips and three hooks).

REAR TRUNK TRIM

PANEL

4 CLIPS

2 CLIPS

710908AE

4.

Remove the right trunk side trim panel the same way.

5.

While wearing eye protection, use a drill to enlarge the two clip holes to 9 mm:

• Wrap tape around the drill bit at 15 to 20 mm from the tip of the bit.

• Remove any burrs from the edge of the holes using a round file.

• Apply touch-up paint to the drilled surface, and allow the paint to dry thoroughly.

• Repeat the above steps to drill the right side of the vehicle.

3 HOOKS

2 of 7

7109060E

AII 42259 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.

LEFT TRUNK

SIDE PANEL

CLIP HOLE

TRUNK LID

HINGE

DRILL BIT

(9 mm)

• Insert the rivet nut into the hole in the left trunk side panel, and install the hex wrench.

2 RIVET NUTS

LEFT TRUNK

SIDE PANEL

TRUNK

LID

HINGE

DRILL

DRILL BIT

CLIP HOLE

15 ~ 20 mm

TAPE

740230CE

6.

Install one rivet nut into each enlarged hole:

• Thread the rivet nut onto the mandrel of the rivet tool as shown.

LEFT TRUNK

SIDE PANEL

2 RIVET NUTS

RIVET NUT

TOOL

HEX

WRENCH

722006CE

• While holding the rivet nut tool with the hex wrench, use a 19 mm wrench to rotate the tool in a clockwise direction until the rivet nut is fully collapsed.

2 RIVET NUTS

RIVET NUT

RIVET

NUT

TOOL

19 mm

WRENCH

RIVET NUT

TOOL

RIVET

NUT

LEFT TRUNK

SIDE PANEL

HEX

WRENCH

MANDREL

771013AE

RIVET NUT

LEFT TRUNK

SIDE PANEL

722007CE

• Remove the tool from the rivet nut by turning the hex wrench counterclockwise.

• Repeat these steps to install a rivet nut in the lower hole in the left trunk side panel.

© 2009 American Honda Motor Co., Inc. – All Rights Reserved.

AII 42259 (0908)

3 of 7

7.

Insert one 6 x 16 mm hex bolt into the hole in the left trunk side panel, and install two 6 mm plain washers and a 6 mm flange nut. Torque the 6 x 16 mm hex bolt to 9.8 N·m (7.2 lb-ft).

 

HEX BOLT, 6 x 16 mm

Torque to 9.8 N·m

(7.2 lb-ft).

LEFT TRUNK

SIDE PANEL

12. Assemble four small anchors.

SMALL ANCHOR

FLANGE NUT,

6 mm

STUD BOLT

HOLE

2 PLAIN

WASHERS,

8.

Install a 6 x16 mm hex bolt to the hole in the right side panel the same way.

9.

Using a pushpin, pierce the center of the circle of dots on the inside of the left trunk side trim panel.

761811AE

13. Install a spacer on the two of the assembled anchors. Note the direction of the spacer.

SMALL ANCHOR

DRILL

STUD BOLT

SPACER

DRILL BIT

(3 mm 11 mm)

LEFT TRUNK

SIDE TRIM

PANEL

PUSHPIN

MARK

722004CE

10. While wearing eye protection, drill at the pierced mark to 11 mm. First drill with a 3 mm bit, and finish with an 11 mm drill bit.

11. Repeat steps 9 and 10 to mark and drill the right trunk side trim panel.

740231AE

4 of 7

AII 42259 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.

14. Reinstall the left and right trunk side trim panel (five clips for each panel).

15. Thread one small anchor with spacer into the upper rivet nut, and install one small anchor without spacer into the lower rivet nut. If the anchors are positioned vertically, turn them to the horizontal position.

Position the anchors horizontally.

RIVET

NUT

TRUNK

LID

HINGE

18. Attach template A to the back of the trunk rear trim panel using masking tape.

TEMPLATE

REAR TRIM PANEL

MASKING

TAPE

PUSHPIN

TEMPLATE

SMALL

ANCHOR

(with spacer)

MASKING

TAPE

REAR TRIM PANEL

LEFT TRUNK

SIDE TRIM PANEL

RIVET

NUT

HEX BOLT,

6 x 16 mm

SMALL ANCHOR

(without spacer)

LARGE

ANCHOR

722009CE

16. Thread one large anchor onto the 6 x 16 mm hex bolt. Position the anchor horizontally.

17. Repeat the steps 15 and 16 to install anchors on the right trunk side trim panel.

Align with the rib.

MASKING TAPE

7220100E

19. Using a pushpin, mark the back of the trunk rear trim panel according to template A. Remove the template.

20. Turn the template over and attach it to the left side of the trunk rear trim panel using masking tape.

PUSHPIN

MASKING

TAPE

TRUNK REAR TRIM

PANEL

MASKING

TAPE

TEMPLATE

TEMPLATE

MASKING

TAPE

Align with the rib.

TRUNK REAR TRIM PANEL

MASKING

TAPE

7220110E

21. Mark the rear trim panel the same way. Remove the template.

© 2009 American Honda Motor Co., Inc. – All Rights Reserved.

AII 42259 (0908)

5 of 7

22. While wearing eye protection, drill a 6.5 mm hole at each marked position. First drill with a 3 mm bit, and finish with a 6.5 mm bit. Remove any burrs from the edge of the holes using a round file.

Installing the Cargo Net

Vertical Position: Hook the loops on the cargo net around the anchors .

LARGE ANCHOR

SMALL ANCHOR

DRILL BIT

(3 mm 6.5 mm)

DRILL

LOOP

CARGO NET

TRUNK REAR TRIM PANEL

7220120E

23. Install the four small anchors to the trunk rear trim panel using one 6 x 16 mm hex bolt, one 6 mm spring washer, and one 6 mm plain washer for each anchor. Torque the 6 x 16 mm hex bolts to 5 N·m (3.7 lb-ft). Position each anchor horizontally as shown.  

4 HEX BOLTS, 6 x 16 mm

Torque to 5 N·m

(3.7 lb-ft).

4   SPRING

WASHERS, 6 mm

4 PLAIN

WASHERS, 6 mm

SMALL

ANCHOR

LOOP

LOOP

LARGE ANCHOR

SMALL ANCHOR

740232BE

4 SMALL

ANCHORS

TRUNK REAR TRIM

722013BE

24. Reinstall the trunk rear trim panel (four clips and three hooks).

6 of 7

AII 42259 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.

Rear Vertical Position

• Attach the magic-fastener as shown on the cargo net.

MAGIC-FASTENER

CARGO NET

MAGIC-FASTENER

740233AE

• Hook the loops on the cargo net around the large anchors. Make sure that the reflective tape is visible.

LARGE ANCHOR

LOOP

REFLECTIVE

TAPE

CARGO NET

740232AE

© 2009 American Honda Motor Co., Inc. – All Rights Reserved.

AII 42259 (0908)

7 of 7