SM-6000
Beltpack Transmitter
OPERATIONMANUAL
Beltpack Transmitter: SM-6000
II iIJ l
~ fJlIlliI
D
Fig.1
.
/(iJ
1.Antenna
2.Battery weak indicator
3.Audio mute switch
4.4 pins mini-XLR connector
5.Power On / Off switch
6.LCD display
7.Charging port
8.UP
9.SET ( Centre)
1a.DOWN
11.Cursor LEFT
12.Cursor RIGHT
13.Cover release button
14.Battery compartment
15.Charging contacts
16.Lavalier microphone
17.Mic clip
Fig.2.
Fig.3.
II
INSTAllATION OF BATTERIES
8M-6000 uses 2 pieces of" AA" size batteries (Alkaline battery is recommended). To install or removethe batteries, press the release buttons at the edges of the transmitter to open or close the cover as illustrated. When installing the batteries with the cover open toward you, the cover might block your hand. It is thus recommendedthat while inserting or removingthe batteries please hold the transmitter in such a way that the cover opens away from you.
Fig.4
n
~
Fig.5
Information on Beltpack transmitter
LCD.
Press Power On switch for about 2 seconds, the following page will appear briefly.
Press down button once more and the CHANNEL I FREQUENCY page will appear:
Press down button once more and the USER NAME page will appear.
Press down button once more and the Brandl Model page will appear.
Press down button once more and the BATTERY SELECTION page will appear:
Press down button once more and the FREQUENCY I BATTERY STATUS page will
Making changes to various settings in Beltpack Transmitter.
1.
Make changes to CHANNEL I FREQUENCY setting.
Use UP or DOWN button to go to the CHANNEL {FREQUENCY page.
Press SET button for about 2 seconds, the cursor will flash to allow changing to be made. Pressing UP or DOWN button will increase or decrease the channel number.
The corresponding frequency will change accordingly. When a desired channel(frequency) is being selected, press SET for about 2 seconds to save and
F1
'.
. .
Remark: When changing transmitter frequencies, care should be taken to avoid causing interference to other channels I users.
2.
Make changes to USER NAME setting.
Use UP or DOWN button to go to the USER NAM page.
Press SET button for about 2 seconds to activate the cursor which willflash to allow changing to be made at the first position. Cursor LEFTand cursor
RIGHTbuttons are for moving the cursor to left or right position. When a change is intended for a particular letter, press cursor LEFTor RIGHTto move the cursor to the desired position.
Press UP or DOWNbutton to roll the ASCII code forward or backward.
When the desired letter or the whole selection is completed, press SET ( centre button) for about 2 seconds to save and store the data in the memory.
3.
Make changes to battery selection setting.
Use UP or DOWNbutton to go to the Battery selection page.
Press SET for about 2 seconds to activate the cursor. Press UP or DOWN
buttonto movethe cursorto either
NiMH ( rechargeable battery) or AKLN(
Alkaline battery) position.
When the desired battery has been selected, press SET for about 2 seconds to save and store the data in the memory.
Remark: NiMHbattery must be selected when rechargeable battery is being used. Never select AKLN(Alkaline) when transmitter is intended for charging as Alkaline battery can not be charged! Wrong selection of battery willresult in battery sensing electronics to display wrong and misleading status information.
51
. .
Operation
Chiayo Transmitters and Receivers have factory preset to allow immediate using after switch-on.
However, please note that the transmitter Sensitivity function is dependent on application such as close proximity singing or tripod mouth speech. To avoid overmodulation and distortion, please check whether the preset sensitivity level is suitable for your particular application. For close proximity singing purposes, please select lowest sensitivity level whereas for tripod mount speech purposes, please select a higher sensitivity level.
If you have made changes to the setting, after making proper selection on
Transmitter and Receiver settings the system is ready for operation. However,
both antenna ofthe receiver
mustbe installed to assure
a good reception.
First switch on the receiver by pressing the Power On I Off switch.
The LCD display will show the information last stored.
Switch on the matching transmitter with the correct matching frequency.
The LCD display will show the information last stored.
The LED RF indicator on the receiver front panel will light up indicating RF signal has been received. If this is not the case, please check and verify the frequency setting on both transmitter and receiver. When transmitter is moving around, the
Diversity A B switch will light on alternately to indicate the stronger reception on either A or B antenna.
When voice is spoken into the microphone, the LED AF indicator on the receiver front panel will light on and flashes according to the intensity of the AF signal.
There are two different
audio outputs at the rear side of the receiver: Balanced (
Microphone level) and Unbalanced ( LINE level ). Please select the matching output to match the input of the connecting Mixer or Amplifier.
II
0;,:-
...'\
..
...
Federal Communication Commission Intt!Tfut!lfct
Statement
,\
'(,' .
...
.
'4
.
This equipment has been tested and found to comply with the limits for a Class B digital device.
pur-
Suatltto Pan 15 of the FCC Rules. These limits are designed to provide reasonable protection agains1 twrmful int~rference in a residential installation, This equipment genel'3tes. uses and can radiated radio frequencyenergy and, if not installed and used in accordance with the instructions. may cause harmful intaference to radio communications, How~er. there is no guarantee that interference will not occur in a particular installation, If this equipment does cause harmful interference to radio or television reception.
which can be detemlined by turning the equipment off and on. the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving an!t:nna,
Increa..;e tM ~paration betWeerl the equipmerlt and receiver,
Connect the equipment into an outlet on a circuit ditTerent from tllatto which the receiver is conneeted
Consult th" dealer or an experienced radioffV technician for help,
FCC C3utioD: To assure continued compliance, (example
use only shielded interface cables when c'ollflccting to computer or peripheral devices), Any changes or modifications not expressly approved by the pr1Y responsible for compliance could void the user's authority to operate this equipment.
This tut1srnitter must not be co-located or operating in conjunction with any other antenna or transmitter, r hi" device complies with Pan IS of the FCC Rules.
Operation is subject to the following tWo conditlnns: (I) This device may not cause harmful interference.
and (2) this device must accept any inter-
,;,rence received.
including interference that may cause undesired operation,
II
'/=,",,
~
CHIAYO
"
CHIAYO ELECTRONICS CO.L~ID._.-
,.--------
111.;, ,v, ,y'", c""", ':z"" ,." E."'",d ,."i,cr""j"h",y(',:o,""'" l A'JE 27 SEC" JE'h\t..
R[)..~C'
P'e.. CHUNG H~;IAO ;;TREET
TA:PFI'-;,,/,At,
CHii".'Y! T!\I'NMi
TeL.. dr..'!-;'.??"",;,"" f.\,.:' ~(j"-;:-;,..,,..,:, ',;'~i
,Et..' i"", 'i,2n ':JlJ:' Fr", ,'I,i::;no,h!:
Pr'nl"'] '" Taiwx, 2%)
