AVAILABLE REPAIR KITS
Rotary Head Kit - Major:
P/N 2100279
Includes items 2, 3, 4, 5, 6, 7, 8, 9,
10, 11, 12, 13, 14, 15 and 16
Rotary Head Kit - Minor:
P/N 2100203
Includes items 9, 10, 12 and 16
Complete Rotary Head Kit:
P/N 2103065
Includes all items
DCG4000 FSC Gun Kit:
P/N 2100274
ITEM
NO.
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
PART
NO.
2500004
2520030
2520028
2520031
2520027
2640015
2701012
2701011
2701010
2720007
2530008
2530007
2200037
2520029
2200038
2710000
DESCRIPTION
Housing, Swivel
Bearing Retainer, Small
Retainer, Bearing
Washer, Bearing Retainer
Spacer, Bearing
Bearing, 15 x 42
O-ring
O-ring
O-ring
Spring, Compression
Pin
Stem, Small
Snap Ring
Snap Ring
Stem, Swivel
Back-up Ring
QTY.
1
1
1
3
2
1
1
1
1
1
2
2
1
1
1
1
PROFESSIONAL FLAT SURFACE CLEANER
FROM GENERAL PUMP
• COMPENSATING GUN FEATURE
• FULL 20” CLEANING PATH
• HEAVY-DUTY ANODIZED
ALUMINUM COMPONENTS
• RUGGED ABS COVER
DCFSCP20
OPERATOR’S MANUAL
WARNING: Read Before Operating Machine
Always wear protective eyewear
Keep clear of rotating nozzles
Never lock trigger gun open with any device
Drain water in cold weather to avoid freezing
Tampering with any part of this machine will void all warranties
General Pump is a member of the Interpump Group
Operating Instructions
1. Connect to Pressure Washer.
2. Turn water on and open valve. Open trigger gun for flow of water through nozzles. Nozzles must have flowing spray. If not, remove tips and clean; reassemble, making sure that groove of nozzle is parallel to spray bar. Use thread sealant when installing nozzles.
3. Start Pressure Washer. The Hammerhead is ready for operation.
4. Walk slowly behind the Hammerhead cleaning as you go. If striping occurs, slow down your pace.
5. Periodically check weep hole on bottom of swivel. Water will seep slowly; if water shoots out, stop and replace seals. Swivel assembly can be rebuilt.
6. For maximum effectiveness keep spray tips clean. If the machine vibrates, stop and clean spray tips.
7. Lubricate swivel with one squirt of good quality grease every 200 hours of operation or about once a month if used daily. A small amount of grease coming out of the swivel is normal.
DO NOT ALLOW MACHINE TO REMAIN STATIONARY
ON SOFT SURFACES SUCH AS WOOD.
Caution: Striking any raised obstacle during operation will damage machine. If contact does occur and results in vibration when operating machine, STOP and replace spray bar. Continued operation could result in serious injury or damage to machine.
Operating Pressures: 1,000 to 4,000 PSI
Max Flow: 8.0 GPM
Dimensions: 70” x 21” x 21”
Weight: 21 lbs.
General Pump
1174 Northland Drive • Mendota Heights, MN 55120
Phone: 651.686.2199 • Fax: 800.535.1745
www.generalpump.com • [email protected]
Ref 300748 Rev.A
08-10
ITEM
NO.
PART
NO.
DESCRIPTION QTY.
9
10
7
8
5
6
3
4
1
2
2103065 Swivel, 20”
2660045 Deck, GP, 20”
2530009 Arm, Rotary, Assy., 20”
2630010 Plate, Retaining
2540023 Collar, Split
2200055 SHCS, M8 X 1.25 X 30, SST
2200054 SHCS, M8 x 1.25 x 25, SST
2540020 Block, Handle
2200047 Bolt, M6
2203406 Washer, M6
11 2540021 Handle, Lower
12 2540037 Handle, Upper
1
2
1
4
1
1
1
1
1
1
8
8
ITEM
NO.
PART
NO.
DESCRIPTION QTY.
21
22
23
24
25
17
18
19
20
13
14
2660047 Grip, Handle
2660046 Plug, Handle
15 2660059 Brush Assy., 20”
16 DCG4000FSC Gun, Flat Surface Cleaner
2702000 Hose, 20”
2200063 Nut, M8 x 1.25, Nylok, SST
D10009
D10004
Plug, 3/9 x 3/8-M
Coupler, 3/8 x 3/8-M
2200028 Nut, Nylok, M6
2202010 Pin, 55mm, w/Ring, SST
2200058 HHCS, M6 X 1 X 60
2200018 Washer, M6
2203507 Washer, M6, SST, Lock
1
1
1
4
1
1
1
1
2
4
2
2
1
