Associated Electrics RC82 Manual & Catalog

PDF

Document

:: Introduction

Thank you for purchasing this Team Associated product. This manual contains instructions and tips for building and maintaining your new RC8.2

Factory Team, 1/8 scale racing buggy. Please take a moment to read through it an familiarize yourself with these steps as they will help you to understand each component’s function and show you some tips for getting the most out of your RC8.2 Factory Team build experience.

:: KIT Features

• 3mm Lengthened 7075 hard anodized chassis

• New Stronger A-arms with centerline shock mounts and optimized anti-roll

bar position.

:: RC8 Platform Features

• 4.30:1 ratio gearboxes

• 43T diff ring and 10T pinion for increased punch and

durability over conventional buggy ratio gearboxes

• 16mm Big Bore Hard Anodized Threaded Shocks with 4mm Titanium Nitride

coated shafts

• 7075 Aluminum Low-CG Shock Towers with optimized geometry

• Brakes

• Heatsink brake discs included

• Brake cam stops ensure brakes aren’t dragging while on

throttle.

• Blue adjustable brake thumb wheels

• 7075 Aluminum suspension mounts front and rear

• 7075 Aluminum Steering Knuckles

• 7075 Aluminum Axles

• 7075 Aluminum Input Cups

• 7075 Aluminum one piece top plate

• Lightweight spur and diff gears

• Lightweight diff outdrives

• Aluminum steering posts

• CVA Boots on Center and Rear joints

• Dual Heat-Sink brake discs

• New Low-CG wing mount

• JConcepts Illuzion Wing

• JConcepts Illuzion Punisher Body

• 2 piece Center diff housing split vertically for easy diff

removal and maintenance

• Caster blocks adjust 14, 16, or 18 degrees with molded

inserts

• Low profile elliptical 2-stage air filter

• High Torque capacity 3-shoe aluminum clutch

• PTFE clutch shim and easy to build design

• Adjustable with 0.9mm, 1.0 mm, and 1.1 mm springs

(not included)

• Fuel tank

• Easily removeable fuel tank only 2 body clips for easy

cleaning

• 3.5mm light CVA drivetrain

• Front and rear hubs use large 15 mm x 24 mm bearing

on the inside

• 14 other 8mm x 16 mm rubber sealed bearings

• Rear molded CVA boots to keep dirt and mud out of rear

joints

• Blue Aluminum hexes and nylon locking wheel nuts

:: Additional Items Needed

Your RC8.2 FT kits comes with the latest components used by our factory race team to win races.

However there are some things that are necessary to complete the build.

• .21 class rear exhaust engine • Muffler, joining pack, or manifold spring (#28045 or #28049 recommended)

• 2 channel radio/transmitter set with switch – FM/PCM/2.4GHz recommended • Transmitter batteries (#302, 303 recommended)

• 4.8-7.4v receiver battery pack

• either flat (#613) or hump (#612) style NiMh battery

• either 1600mAh LiPo (#630), 2100mAh LiPo (#631), or 1700 LiFe (#638) battery (recommended)

• Model car fuel (30% nitro recommended) • Fuel bottle (#1748 recommended)

• Glow igniter (#1738 recommended) • Starter box (#1750 recommended)

• 1/8th scale buggy tires • CA (Cyanoacrylic) glue (#1597 recommended)

• Polycarbonate specific spray paint or polycarbonate specific bottled paint and airbrush

• Thread locking compound (#1596 recommended)

• Needle nose pliers • Hobby knife • Reamer/hole punch • Ride Height Gauge (#1449 recommended)

:: Other Helpful Items

• Silicone Shock Fluid / Differential Fluid (Refer to catalog for complete listings)

• Body Scissors (AE Part # 1737)

• FT Hex Wrenches (AE Part # 1541, 1655)

• FT Nut Drivers (AE Part #1561, 1663-1668)

• Reamer / Hole Punch

• Needle Nose Pliers

• FT Turnbuckle Wrench (#89240)

• Multi Tool (AE Part #7494)

• Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)

• Hobby Knife

• Wire Cutters

• Soldering Iron

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

:: Table of Contents

1....................Cover

2....................Introduction

3....................Table of Contents

BAG A

4....................Chassis Assembly

BAG B

4-5................Steering Assembly

Bag C

6-9................Front, Rear, and Center

Differential Assembly

Bag D

9-11.............Front Bulkhead Assembly

Bag E

11-14..........Front Suspension Assembly

Bag F

15-16..........Rear Bulkhead Assembly

Bag G

16-19..........Rear Suspension Assembly

Bag H

20-21..........Wing Assembly

Bag I

21-22..........Center Bulkhead Assembly

Bag J

23-25.........Shock Assembly

Bag K

26-30.........Radio Tray Assembly

Bag L

30-33.........Fuel Tank, Air Filter, Engine, and

Pipe Installation

Bag M

34................Wheels, Tires, and Body Install

34.................Building Tips

35................Chassis Tips

35................Front End Tips

36................Rear End Tips

37.................Droop Settings

38-49.........Catalog

49.................Contact Info

50.................Notes

51.................Setup Sheet “Kit Setup”

52................1:1 Hardware “Fold Out

53................Setup Sheet “Blank”

54................Back Cover

:: Notes

This symbols indicates a special note or instruction in the manual.

There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

:: Chassis Assembly - Bag A

89552

RC8.2

side guards x2

89476

FT RC8B

+3mm chassis

:: Chassis Assembly (cont.) - Bag A

89485

RC8B x2 aluminum steering posts

#1596 thread lock

:: Steering Assembly - Bag B

89016

Servo saver bolt

gap setting:

7mm

89015

Servo saver arm

89015

Servo saver bellcrank

89214

4x12mm fhcs x2

89117

Diff shim x2

89016

Servo saver spring

89016

Servo saver retainer

25201

3x8mm fhcs x4

89161

5x8mm bearing x4

89014

Steering rack post x2

:: Steering Assembly (cont.)- Bag B

89074

Steering eyelet x2

Build Two

29mm

89526

50mm steel turnbuckle

Smooth edge towards drivers side!

89242

Steering drag link

89077

Flanged pivot ball x2

89075

RC8 steering ballstuds x2

89455

3x22mm fhcs x2

:: Steering Assembly (cont.)- Bag B

89011

Front body mount

89234

Aluminum top plate

(blue)

#1596 thread lock

25202

3x10mm fhcs

89258

Front chassis brace

(plastic)

89455

3x22mm fhcs

:: Steering Assembly (cont.)- Bag B

#1596 thread lock

89214

4x12mm fhcs x2

#1596 thread lock

note the direction of the body post during installation.

31404

6x10mm bearing x4

25215

M3 locknut x2

25215

M3 locknut

89209

3x18mm fhcs

:: Front/Rear Differential Assembly - Bag C

Center Diff

Outdrive

89115

Diff housing

Diff outdrive differences

Front Diff

Outdrive

(long)

25236

8x16mm bearing

Rear Diff

Outdrive

(short)

:: Front/Rear Differential Assembly (cont.) - Bag C

89120

Diff washer x2

#6588 black grease

89120

Diff outdrive pin

89121

Diff

O-Ring

#6588 black grease

89477

Light outdrives

(front, long)

89121

Diff

O-Ring

89120

Sun gear

89478

Light outdrives

(rear, short)

Align pin with groove in sun gear

:: Front/Rear Differential Assembly (cont.) - Bag C

89120

Spider gear assembly

:: Front/Rear Differential Assembly (cont.) - Bag C

89478

Light outdrives

(rear, short)

89121

Diff

O-Ring

#6588 black grease

89477

Light outdrives

(front, long)

25236

8x16mm bearing

89494

Light diff ring gear

:: Front/Rear Differential Assembly (cont.) - Bag C

89120

Diff outdrive pin

89120

Diff washer x2

89120

Sun gear

Align pin with groove in sun gear

:: Front/Rear Differential Assembly (cont.) - Bag C

89116

Diff gasket

Tighten screws evenly and firmly.

89208

3x14mm fhcs x4

#6588 black grease

Diff fluid

5,000cst

Fill with diff fluid to top of gears.

89121

Diff

Build front and rear diffs!

:: Center Differential Assembly - Bag C

89115

Diff housing

89121

Diff

O-Ring

25236

8x16mm bearing

#6588 black grease

89119

Diff outdrives

(center)

:: Center Differential Assembly (cont.) - Bag C

89120

Sun gear

89120

Diff outdrive pin

89120

Diff washer x2

89121

Diff

O-Ring

89120

Spider gear assembly

Align pin with groove in sun gear

:: Center Differential Assembly (cont.) - Bag C

89119

Diff outdrives

(center)

89121

Diff

O-Ring

#6588 black grease

25236

8x16mm bearing

89495

Light spur gear

(44T)

#6588 black grease

:: Center Differential Assembly (cont.) - Bag C

89120

Diff washer x2

89121

Diff

O-Ring

89120

Diff outdrive pin

89120

Sun gear

Align pin with groove in sun gear

:: Center Differential Assembly (cont.) - Bag C

89116

Diff gasket

Tighten screws evenly and firmly.

89208

3x14mm fhcs x4

#6588 black grease Diff fluid

5,000cst !

Fill with diff fluid to top of gears.

:: Front Bulkhead Assembly - Bag D

89103

Center CVA bone

(front)

89557

Pin retainer boot

89106

CVA u-joint coupler

#6588 black grease

89106

CVA pin

89286

Gearbox input cup

(aluminum)

89557

Pin retainer

O-ring

Input cup has additional holes for crosspin to extend the life of the input cup.

:: Front Bulkhead Assembly (cont.) - Bag D

Wrap boot over the O-Ring.

25236

8x16mm bearing x2

89017

Inner gearbox

:: Front Bulkhead Assembly (cont.) - Bag D

Key setscrew onto flat side of shaft.

Tighten with no endplay.

89221

5x4mm setscrew

#1596 thread lock

89481

Low

B-Plate

89474

3x22mm shcs x2

89114

Diff pinion gear

:: Front Bulkhead Assembly (cont.) - Bag D

89538

RC8.2 front shock tower

(aluminum)

89454

3x12mm shcs x4

89224

3x16mm shcs x2

89472

Front bulkhead spacer

89017

Outer gearbox

89117

Diff shim x2

25215

M3 locknut x4

Diff shims installed to gear diff, gear diff installed to gearbox.

:: Front Bulkhead Assembly (cont.) - Bag D

#1596 thread lock

89473

Steel shock standoffs x2

#1596 thread lock

89225

3x24mm shcs x2

89230

Silver cone washer x2

:: Front Suspension Assembly - Bag E

89105

CVA u-joint coupler

89285

Front stub axle

(aluminum)

89105

CVA pin

#6588 black grease

89102

CVA bone

Axle has additional holes for crosspin to extend the life of the Axle.

:: Front Suspension Assembly (cont.) - Bag E

Right Side

89162

15x21x4mm bearing

Build right and left sides!

89380

FT machined steering blocks

Build Two!

89096

Wheel hex pins

Build right and left sides!

Left Side

25236

8x16x5mm bearing

89095

Wheel hex

(aluminum)

89223

3x8mm shcs

#1596 thread lock

:: Front Suspension Assembly (cont.) - Bag E

Note:

One drop only.

Spread evenly inside the threads.

89029

Steering block bushing

(short)

#1596 thread lock

89558

RC8.2 caster blocks

Build right and left sides!

89029

Steering block bushing (long)

89207

4x12mm bhcs

:: Front Suspension Assembly (cont.) - Bag E

89536

RC8.2 swaybar pivot ball

89206

4x10mm bhcs

#1596 thread lock

Do not tighten until bushing is keyed into steering block.

25192

3x20mm shcs

Note:

Key bushings into steering block.

Build right and left sides!

89537

RC8.2 swaybar ball joint

89537

RC8.2 swaybar drop link

Build Two!

:: Front Suspension Assembly (cont.) - Bag E

Droop screw placement!

89317

Droop screw

89550

RC8.2 front arms

89032

16 deg. caster angle bushing

(red)

Note: direction blue

16 deg

1 6 deg red

31520

2.5x6mm

bhcs

89032

16 deg. caster angle bushing

(blue)

89041

Outer hinge pin

Build right and left sides!

:: Front Suspension Assembly (cont.) - Bag E

89549

RC8.2 front upper arm

89076

Camber rod ends

89269

38mm steel turnbuckle

89230

Silver cone washer x2

Smooth edge towards drivers side!

Build right and left sides!

89225

3x24mm shcs

25215

M3 locknut

8mm

:: Front Suspension Assembly (cont.) - Bag E hinge pin bushing

89553

RC8.2 inner x2 hinge pins

(front)

2 dot up

89039

Hinge pin x2 bushings

(two dot)

89230

Silver cone washer x2

89279

3x45mm shcs x2 89460

Aluminum

A-plate

:: Front Suspension Assembly (cont.) - Bag E

25225

3x3mm setscrew x2

#1596 thread lock

89533

RC8.2 FR swaybar

2.3 (white)

89482

Low B-plate insert x2

89227

3x28mm shcs

31531

3x6mm bhcs x2 89017

Swaybar mount

89219

3x5mm setscrew x2

Tighten screws to remove free play but ensure some movement.

25215

M3 locknut

Side view

:: Front Suspension Assembly (cont.) - Bag E

89227

3x28mm shcs

89018

Gearbox gasket

89022

Front bumper

89217

4x14mm fhcs x2

89214

4x12mm fhcs x2

:: Front Suspension Assembly (cont.) - Bag E

Shock tower hinge pin bushing hinge pin bushing

1 dot

89039

Hinge pin x2 bushing

(three dot)

3 dot down

89040

Upper inner hinge pin x2

31531

3x6mm bhcs x2

89218

3x8mm washer x2

89470 x2

Shock tower hinge pin bushings

(one dot)

25215

M3 locknut

Build right and left sides!

89218

3x8mm washer

:: Rear Bulkhead Assembly - Bag F

89560

Center CVA bone +3mm

(rear)

#6588 black grease

89106

CVA u-joint coupler

89557

Pin retainer boot

Input cup has additional holes for crosspin to extend the life of the input cup.

:: Rear Bulkhead Assembly (cont.) - Bag F

89106

CVA pin

89286

Gearbox input cup

(aluminum)

89557

Pin retainer

O-ring

89114

Diff pinion gear

89017

Inner gearbox

Wrap boot over the O-Ring.

25236

8x16mm bearing x2

:: Rear Bulkhead Assembly (cont.) - Bag F

Key setscrew onto flat side of shaft.

Tighten with no endplay.

89221

5x4mm setscrew

#1596 thread lock

89462

Aluminum

C-plate

25191

3x18mm shcs x2

:: Rear Bulkhead Assembly (cont.) - Bag F

89011

Body mount

(rear)

25620

3x10mm shcs x2 89454

3x12mm shcs

89224

3x16mm shcs x2 x2

89017

Outer gearbox

89539

RC8.2 rear shock tower

(aluminum)

:: Rear Bulkhead Assembly (cont.) - Bag F

tapered side of cone washer faces towards chassis brace

89225

3x24mm shcs x2

89227

3x28mm shcs

89258

Chassis brace

(rear)

89117

Diff shim x2

25215

M3 locknut x2

Diff shims installed to gear diff, gear diff installed to gearbox.

89473

Steel shock standoffs x2

89230

Silver cone washer x3

25215

M3 locknut

:: Rear Suspension Assembly - Bag G

89102

CVA bone

89105

CVA u-joint coupler

#6588 black grease

89107

CVA boot

:: Rear Suspension Assembly (cont.) - Bag G

89105

CVA pin

(fr/rr)

89284

Rear stub axle

(aluminum)

Axle has additional holes for crosspin to extend the life of the Axle.

:: Rear Suspension Assembly (cont.) - Bag G

89162

15x21mm bearing

89033 hub carrier

Build right and left sides!

25236

8x16mm bearing

:: Rear Suspension Assembly (cont.) - Bag G

89107

Bearing shield

Build Two!

Build right and left sides!

89096

Wheel hex pins

89095

Wheel hex

(aluminum)

89223

3x8mm shcs

#1596 thread lock

89537

RC8.2 swaybar ball joint

89537

RC8.2 swaybar drop link

89536

RC8.2 swaybar pivot ball

Build Two!

:: Rear Suspension Assembly (cont.) - Bag G

Droop screw placement!

89317

Droop screw

25192

3x20mm shcs

89551

RC8.2

rear arm

Build right and left sides!

:: Rear Suspension Assembly (cont.) - Bag G

89076

Camber rod end x2

6mm

89076

Camber ball joints x2

89269

38mm steel turnbuckle

Passenger

Side

Smooth edge towards drivers side!

Driver

Side

89454

3x12mm shcs x2

89076

Camber pivot balls x2

89561

Rear mud guard

Build right and left sides!

:: Rear Suspension Assembly (cont.) - Bag G

Note the direction of rod end when installing.

Right side shown.

89474

3x22mm shcs

25215

M3 locknut !

Build right and left sides!

31520

2.5x6mm

bhcs

89031

Hub spacers x2

89041

Outer hinge pin

:: Rear Suspension Assembly (cont.) - Bag G hinge pin bushing

1 dot

89039

Hinge pin bushings x2

89463

Aluminum

D-plate

89452

3x50mm shcs x2

89466 x2

Inner hinge pin

(4mm HMA)

::: Rear Suspension Assembly (cont.) - Bag G

89470 x2

Hinge pin bushings

(two dot)

25215

M3 locknut x2

1 hinge pin bushing

2 dot down

89230

Silver cone washer x2

25192

3x20mm shcs x2

::: Rear Suspension Assembly (cont.) - Bag G

#1596 thread lock

25225

3x3mm setscrew x2

89487

RC8B rear swaybar

(2.5 green)

#1596 thread lock

31531

3x6mm bhcs x2

89017

Swaybar mount

:: Wing Assembly - Bag H

25204

3x16mm fhcs x2

89229

Blue x2 countersunk washer

89304

JC Illuzion wing

89540

RC8.2

Wing mount upper brace

25192

3x20mm shcs x2

25215

M3 locknut x2

89540

RC8.2

wing mounts x2

:: Wing Assembly (cont.) - Bag H

Tighten screws to remove free play but ensure some movement.

25215

M3 locknut

89219

3x5mm setscrew x2

89228

3x40mm shcs

25215

M3 locknut x2

:: Rear Clip Install - Bag H

25215

M3 locknut

:: Center Bulkhead Assembly - Bag I

89122

Brake pads x2

89019

Center bulkhead

(top) brake pad gap: 4.5mm

#6588 black grease

89018

Gearbox gasket

89217

4x14mm fhcs x2

89209

3x18mm fhcs

89214

4x12mm fhcs x2

89122

Brake bolt x2

Build Two!

89123

Heatsink brake disc x2

:: Center Bulkhead Assembly (cont.) - Bag I

Do not tighten

#89226 3x26mm shcs completely until the next step!

89226

3x26mm shcs x4

89254

Center diff top plate

89124

Brake cam x2

89019

Center bulkhead

(bottom) x2

:: Center Bulkhead Assembly (cont.) - Bag I

Tighten all screws after bottom screws have been installed!

Install CVA bones into center diff outdrives!

89214

4x12mm fhcs

:: Shocks Assembly - Bag J

89358

Lower shock tool

Use the lower shock tool to load the two o-rings and spacer for easy lubing and installation into the shock body

:: Shocks Assembly (cont.) - Bag J

Install piston tapered side down.

89352

O-Ring

89352

Bottom nut

89554

4x26mm

HD shock shaft, front

89555

4x36mm

HD shock shaft, rear

:: Shocks Assembly (cont.) - Bag J

Short boots for front shocks.

Long boots for rear shocks.

89556

RC8.2 shock boots

(fr/rr)

89066

Shock

O-rings x2

89352

Spacer

89215

Locknut

(piston)

89492

16mm piston

5x1.1 + 5x1.2

89278

2.5mm piston washer x2

89358

Upper shock tool

Shock fluid

Fill to top with shock fluid:

Front: 30wt

Rear 30 wt

89469

Shock rod end ball

89291

16x29mm

FT shock body

(front)

89344

16x38mm

FT shock body

(rear)

Shock fluid

One drop of shock fluid on threads.

RACERS TIP:

Try 35 wt or 40wt shock fluid in the front shocks for less agressive steering.

89469

HD shock ends

:: Shocks Assembly (cont.) - Bag J

Bladder Installation

A B C

As you install the shock cap with the bladder, it will force out any extra fluid. If you install the cap with the shaft fully extended, you are running FULL REBOUND.

To run less rebound, unthread the cap 1-2 turns and compress the shaft to the desired position and re-tighten the cap with the shaft compressed.

Start with no rebound.

:: Shocks Assembly (cont.) - Bag J

Shock fluid

89352

Threaded shock collar

O-Ring

89355

Threaded shock collar

89543 x2

Front spring, silver (4.3lbs)

(short spring)

89547 x2

Rear spring, silver (3.55lbs)

(long spring)

:: Shocks Assembly (cont.) - Bag J

Note the direction of the shock cap when installing onto shock standoffs

89083

Shock bushing

Install two front shocks.

25612

M3 locknut with flange

89354

16mm shock spring cup

89335

Shock cap

89351

Shock bladder

Some residual shock fluid may appear from your first few runs around the shock cap as a result of bleeding.

Build two front and two rear shocks!

:: Shocks Assembly (cont.) - Bag J

106mm

Install two front shocks.

91069

Shock mount pin, steel

:: Shocks Assembly (cont.) - Bag J

Note the direction of the shock cap when installing onto shock standoffs

Note the wing has been hidden for picture clarity only.

89083

Shock bushing

Install two rear shocks.

25612

M3 locknut with flange

:: Shocks Assembly (cont.) - Bag J

89454

3x12mm shcs

After installation, adjust droop screw to get a front shock length of

106mm measured center to center on the shock cap / eyelet.

122mm

Install two rear shocks.

91069

Shock mount pin, steel

89454

3x12mm shcs

After installation, adjust droop screw to get a rear shock length of

122mm measured center to center on the shock cap / eyelet.

:: Radio Tray Assembly - Bag K

89003

Wire insert

89253

Antenna mount

89004

Receiver box foam pad

(bottom)

Receiver not inlcluded!

89003

Receiver box

:: Radio Tray Assembly (cont.) - Bag K

5 cell inline pack configuration shown. For hump pack or

LiPo packs, use forward battery box on page 27.

6338

Antenna tube and cap

89222

2.5x8mm

shcs x2

89003

Switch mount

89003

Receiver box top

On/off switch and mounting screws are not inlcluded!

89004

Receiver box foam pad (top)

21173

Small body clip x2

25203

3x12mm fhcs x2

89253

Radio tray

:: Radio Tray Assembly (cont.) - Bag K

89209

3x18mm fhcs x2

89208

3x14mm fhcs x6

89229 x8

Countersunk washers

(blue)

Servo’s not inlcluded!

89006

Servo spacers x4

Servo mounts vary per servo manufacturer.

Space your servos low to the chassis without touching the bottom.

31531

3x6mm bhcs x2

Transponder not inlcluded!

:: Radio Tray Assembly (cont.) - Bag K

89454

3x12mm shcs x2

89471

Forward battery box

(top)

25187

3x14mm bhcs

89471

Forward battery box foam pad

(top)

89471

Forward battery box foam pad

(bottom)

89214

4x12mm fhcs

89471

Forward battery box

(bottom)

Insert the receiver battery wire into the receiver box!

:: Radio Tray Assembly (cont.) - Bag K

A - Airtronics

F - Futaba

H - Hitec

J - JR

Printed here

Enlarge holes in servo horn!

89078

Servo link rod end x2

25215

M3 locknut

89007

Servo cone washer

89007

Steering servo horn

89078 ball joint x2

89267

32mm steel turnbuckle

2308

3x18mm bhcs

7mm

25201

3x8mm fhcs

#1596 thread lock

89007

Servo horn ring

Wire routing diagram

:: Radio Tray Assembly (cont.) - Bag K

89008

Servo cone washer

Printed here

A - Airtronics

F - Futaba

H - Hitec

J - JR

89126

Brake bias block

89218

3x8mm washer

Enlarge holes in servo horn!

89008

Throttle servo horn

89203

3x16mm bhcs

25215

M3 locknut x2

25225

3x3mm setscrew x2

89216

Throttle pivot

89202

3x12mm bhcs

When adjusting linkage, it may be necessary to change hole location for correct alignment with carburetor

89008

Servo horn ring

89126

Brake link x2

:: Radio Tray Assembly (cont.) - Bag K

#1596 thread lock

89126

Throttle spring

25225

3x3mm setscrew

25225

3x3mm setscrew

89126

Throttle link

89126

Set collar

89126

Throttle ball cup

89126

Brake bias collar

:: Radio Tray Assembly (cont.) - Bag K

#1596 thread lock

25201

3x8mm fhcs

25225

3x3mm setscrew x2

#1596 thread lock

89126

Brake bias collar x2

89318

Brake lever x2

:: Radio Tray Assembly (cont.) - Bag K

25203

3x12mm fhcs x6

There will be an unused screw hole at the bottom of the receiver box.

This will not be used for the RC8.2

:: Radio Tray Assembly (cont.) - Bag K

89126

Brake washer x2

89126 brake spring

(silicone) x2

25225

3x3mm setscrew x2

89126

Set collar x2

89205

3x26mm bhcs

25215

M3 locknut

After installation, leave a 0.5mm gap between the two brake levers!

0.5mm

:: Radio Tray Assembly (cont.) - Bag K

:: 2

1mm gap

:: 6

:: 5

:: Brake bias adjusters

:: Rear :: Front

:: 9

:: 1

:: 3

:: 4

::1 - Turn on transmitter and buggy. Adjust servo

horn until position is parallel with centerline at

neutral.

::2 - Set pre-load on spring so that throttle will

close.

::3 - Set 0.5mm gap on throttle collar.

::4 - Trim off excess rod.

::5 - Pull cams to engage brakes. Set collar

(with brakes engaged) to have 1mm gap

between tubing and collar.

Remember: transmitter is still on during this step.

::6 - Trim off excess brake link wire.

::7 - Set throttle EPA to max. Apply full throttle on

transmitter and set EPA so that the carb is full

open. Be careful not to over-extend the carb.

::8 - Set max brake EPA at 30% as a starting point.

::9 - Brake bias adjusters: thread the adjuster into the

mount to achieve stronger brakes on that end of

the buggy.

:: Fuel Tank Install - Bag L

89131

Fuel tank

21173

Small body clip x2 cut

76mm 89066

O-Rings x2

89128

Fuel tank mount x2

25203

3x12mm fhcs x2

:: Air Filter Install - Bag L

When oiling the filter elements, place both inside a plastic bag and squeeze to help evenly coat the filter.

89142

Air filter outer element

89141

Air filter inner element

89139

Air filter base

89139

Air filter cap

25201

3x8mm fhcs x2

Engine not included!

89140

Air filter hose

:: Engine Install - Bag L

RACERS TIP: trim clutch shim.

89138

Flywheel collet

89134

Clutch shoes

(aluminum) x3

89135

Clutch nut

89133

1.0mm clutch springs x3

Clutch shimming instructions:

If assembly does not spin freely, use #89218

(small clutch shim included in kit) on screw to increase end play.

89137

Clutch shim

89136

Flywheel

Use upper shock tool to install clutch springs.

If crankcase extends past clutch bearing, use#89218

(large clutch shim included in kit) to reduce end play.

89223

3x8mm shcs

:: Engine Install (cont.) - Bag L

89224

3x16mm shcs x4

89231

3mm lock washer x4

3719

6” wire tie

Use #3917 wire tie here!

89218

3x8mm washer

89132

16T clutchbell

89148

Clutchbell shim x5

25237

5x10mm bearing x2

89257

Engine mount x2

#1596 thread lock

Muffler and header not included

:: Engine Install (cont.) - Bag L

25226

4x5mm setscrew

#1596 thread lock

89144

Pipe mount

:: Engine Install (cont.) - Bag L

25201

3x8mm fhcs

89145

Pipe wire

Pipe setscrew not included!

89130

Engine mount plates x2

#1596 thread lock

89213

4x6mm fhcs x6

89207

4x12mm fhcs x4

#1596 thread lock

:: Engine Install (cont.) - Bag L

Pressure line from fuel tank lid to exhaust pipe nipple

Fuel line from fuel tank to carburetor

:: Engine Install (cont.) - Bag L

89325

Fuel line clips x2

Install fuel line clips!

Adjust angle of carb ball joint to align with throttle servo.

:: Wheels, Tires, and Body Install - Bag M

#0218

Jconcepts

Punisher body

(sold @jconcepts.net

31531

3x6mm bhcs

2208

Large hood pins x2

Body :

Your RC8.2 comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent.

Dry using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE (RC cars get painted from the inside). Using high quality tape, apply to create a design to the inside of the body. Spray (either can or airbrush) the paint to the inside of the body (NOTE: use ONLY paint that is recommended for use with

(polycarbonate) plastics. If you don’t, you will destroy the plastic body!!!!).

After painting, cut the body along the trim lines. Make sure to cut holes for the engine head, body mounts, antenna, fuel tank lid, top end adjustment needle and muffler outlet.

89269

83mm wheel

(white) x4

Tires not included!

89094

Wheel hex nuts x4

Tires: (not included in kit)

Your tires need to be glued to the wheels using a fast-curing Tire glue

(CA) (AE Pt#1597). This is available at your local hobby shop. Make sure to clean the mounting surface of the tire with alchohol for best adhesion.

:: Building Tips

Tires:

The tires need to be glued to the wheels using any fast-curing FT Tire glue (CA) (AE Pt#1597). This is available at your local hobby shop. Make sure to clean the mounting surface of the tire with alchohol for best adhesion.

Gear Mesh:

To correctly set your gear mesh, follow the steps below:

1. Loosen engine mount screws so you can slide your engine and mount.

2. Slide engine and mount until the clutchbell gear comes in contact with the spur gear. Tighten engine mount screws.

Hold the spur gear in place and ‘rock’ the clutchbell gear. There should be a little ‘free-play’ between the gears.

3. If you have a small amount of ‘free-play’, continue building your RC8.2. If not, go back to Step 1.

Receiver Pack:

Your RC8.2 does not come with a receiver pack. It is recommended that you use a 5-cell 1600mah pack (minimum) in either stick (AE Pt #612) or hump (AE Pt#613) pack configuration (your RC8.2 will accepteither). Charge your pack per the battery manufacturer’s instructions. This will need to be done before you can setup up your RC8.2.

Engine Tuning:

Follow the manufacturers instructions to correctly tune your engine. You will need to adjust the fuel mixture according to altitude, weather, etc.

:: Chassis Tips

Gearing:

Recommended gearing: 16:44. This is a good starting point for most tracks. Follow your engine manufacturer’s recommendations for gearing options. Typically on larger, more open track layouts a 17T clutch bell is used.

Gear Mesh:

To correctly set your gear mesh, follow the steps below:

1. Loosen the engine mount screws so you can slide your engine from side to side freely.

2. Slide the engine until the clutch bell comes in contact with the spur gear. Tighten the engine mount screws.

Now “rock” the spur gear. There should be a little “free play” between the gears.

3. If you have a small amount of ‘free-play’, continue building your RC8.2. If not, go back to Step 1. Be sure to check for

“free-play” through a full rotation of the spur gear.

WARNING!

Caution when setting / checking gear mesh after running your vehicle, the clutch bell WILL BE HOT!

Differential Fluid:

Team Associated includes a complete bottle of 5,000cst diff oil. You can also provide your own oil and try one of the optional setups.

Standard differential fluid setup: Front = 5,000cst; Center = 5,000cst; Rear = 5,000cst.

Optional diff setup 1 (high grip track): Front = 5,000cst; Center = 10,000cst; Rear = 5,000cst.

Center Differential:

Use the standard setup for most cases. Some racers will try thicker oil (7,000-10,000cst) when greater acceleration is needed. This is typically done on very smooth tracks since thicker fluid can reduce handling in bumpy conditions.

:: Front End Tips

Front Differential:

Use the standard setup for most cases. Try 7,000cst to 10,000cst to get less low speed steering and better acceleration out of turns.

Kickup Bushing:

Generally more kick-up will provide better handling in the bumps and have better straight line acceleration.

Less kick-up will provide more all around steering and have a more aggressive feel.

Caster:

The standard caster block insert setup is for 16 degrees. The standard inboard kick-up is 9 degrees (2-dot up insert in A-plate). You can reduce the caster using 14 degree inserts (also move both upper cone washers in front of the ball joint) for smoother steering. Changing to 18 degree inserts (also move both upper cone washers behind the ball joint) will typically provide more steering on power but reduce handling in bumpy conditions.

Front Upper Pivot Insert:

The standard setup is to use 2-dot up in the tower and 1-dot in the top plate. It is recommended to maintain a 1 dot gap (1mm per dot) front to rear when using 2-dot up in the A-Plate. Reducing the A-Plate insert to 1-dot allows the use of same dot number insert in both tower and top plate. Going up to 3-dot up in the tower will give more turn in, but less steering on power/exit. Going down (1-dot, 2-dot down) will reduce turn in, but give more steering on exit.

Front Camber Link-Outer:

The standard short location will work the best for most tracks. Going to the long front link will give you more steering, but can make the car less predictable in bumps and exiting turns.

Front Camber Angle:

A good starting camber setting is –2 degrees. Positive camber, where the top of the tire is leaning out, is typically not recommended.

Front Toe-In:

Zero degree toe-in (tires pointing straight forward) is a good starting setting. You can increase turn in by adding 1-2 degrees of toe-out (front of tires point slightly out). Front toe - in is not a typical tuning adjustment used by the Team.

Front Ride Height:

The front ride height setting you should use most often is with 29mm of gap between the chassis bottom and the ground. Check the ride height with the FT Ride Height Gauge (#1449) by lifting up the entire vehicle about 8-12 inches off the bench and drop it. After the suspension “settles” into place, then raise or lower the adjustment collars as necessary and recheck.

Front Arm Shock Location:

Inside on the arm will give a more responsive front end. Outside on the arm will be less responsive steering, but will be more predictable through bumps.

:: Rear End Tips

Rear Differential:

Start with the standard setup. For expert drivers, the most popular setting for buggy is 3,000 cst. the thicker

5,000cst kit oil will rotate less in the turns and accelerate straight on power. The thinner oil (2,000 or 3,000cst) will give more low speed traction.

Anti-squat:

Anti-squat denotes the angel of the rear inner hinge pin relative to the ground. This setting is adjusted by changing the insert bushing in the C-Plate. The kit setting is 2 degrees (2-dot down) but you change to 1 degree (3-dot down). Typically less anti-squat lets the suspension work more over the bumps, but it will sacrifice the ability to square up on power.

Rear Camber Link Length & Vertical Adjustment:

You can change the length of the camber link on the hub or tower as well as adjust the vertical location on the tower.

A longer link will give the feeling of the most grip, but it will not be as responsive to square up on throttle, and might get loose if driven hard. This can easily be corrected by running the shorter link on the hub, but it will sacrifice some forward grip.

Changing to a higher location on the tower will be a smaller adjustment than changing the length of the upper link.

Going up on the tower location has a similar effect as a longer camber link, but not as drastic. For example, if you change to the short rear link on the hub and you need to gain more forward grip, try raising the link up on the tower. New additional lower holes should be used when running the optional hinge pin hole in the rear hub carrier.

Rear Hub Hinge Pin Height:

The upper hole gives more rear grip on turn in, and good forward traction, but it might have difficulty squaring up out of turns. The lower hinge pin hole in the hub will be more responsive on throttle, and give more side grip in the turns.

Rear Hub Spacing:

You have 3 options for rear hub spacing, FWD, MIDDLE, & BACK. The kit setting provides a good balance of rear traction and steering, and will be used most often. Moving the hubs FWD will give more rear traction for low grip tracks.

You can use the hubs BACK on high grip tracks for more on-power steering. Also, you can replace the included shims to get intermediate settings.

Rear Camber:

A good starting camber setting is –2 degrees. Use the included #1719 camber gauge to set your camber. Adding a small amount of positive camber, where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.

Rear Ride Height:

The rear ride height setting you should use most often is 29mm of gap between the chassis bottom and ground.

Check the ride height with the FT Ride Height Gauge (#1449) by lifting up the entire vehicle about 8-12 inches off the bench and drop it. After the suspension “settles” into place, then raise or lower the adjustment collars as necessary and recheck.

Rear Arm Shock Location:

Inside on the arm will give less entry steering, accelerates better straightline through bumps, but may lack side bite.

Outside on the arm will be less grip, more steering, but will be more predictable when it breaks traction.

:: Droop Settings (Truggy shown but applicable for all vehicles)

Step 1:

With only the bottom of the shocks attatched, the droop screws raised all the way, and the chassis above your working surface so the arms are at full extension, you should be able to easily slide the top of your shock over the standoff screw, while leaving the shock at full extension. If the mounting hole of the shock cap is above or below the standoff screw, adjust the droop screw accordingly. Repeat for all corners of your vehicle. Measure from the center of the standoff screw to the center of the shock riser button to get your FULL DROOP setting.The front shocks should be

109mm, while the rear shocks should be 127.5mm.

Step 2:

Finish installing the shock to the standoff.

Set your vehicle to your desired droop setting.

To increase your droop turn the droop screw (from the top) counter-clockwise (loosen), turn the droop screw

(from the top) clockwise (tighten) to decrease your droop. Remember, never back the screw out beyond full droop or you could risk damage to your vehicle.

Step 3:

Measure from the center of the shock standoff screw to the center of the shock riser button to get your final droop setting. The front shocks should both be set at the same lenght, as should the rear shocks. * The normal droop setting is between 0-5mm from the FULL DROOP measurement.

Front Droop:

Increasing front droop (loosen droop screws) will increase off-throttle steering. It also allows the front end to lift more, giving more rear grip and less front grip on-power. Remember to never loosen the screws beyond the FULL DROOP setting. Decreasing front droop (tighten droop screws) yields more on-power steering and quicker response at the expense of some stability in bumpy sections. It will also give less off-throttle steering.

Rear Droop:

Increasing rear droop (loosen droop screws) will increase traction in bumpy sections, but will reduce high-speed stability. Remember to never loosen the screws beyond the FULL DROOP setting. Decreasing rear droop

(tighten droop screws) will increase stability in high speed sections, but will reduce stability in bumpy sections.

Setup Sheets:

Most often the best way to get your car handling right is to go to our website www.rc10.com and click on the

“Setup Sheets” link, then the link to your vehicle, then search for your vehicle. Our team of professional drivers help develop these setups at National events. Also, most drivers have a “base” setup that they use as a starting point for every event. Try running some of our base setups OR look for track conditions and tires that are similar to your local track and mimic that setup. Remember, each adjustment has a purpose, so copy everything from the setup sheet and then make adjustments based on the recommendations in here at http://www.rc10.com/rc/tuning.

:: Shocks

25612

89066

89067

89083

89215

89278

89290

89291

89335

89344

89346

89351

89352

89353

89354

89355

89469

89492

89554

89555

89556

M3 Locknut With Flange

Shock O-Rings

Shock Limiters, Set

Shock Bushings

Piston Locknut

2.5mm Washer

16x29mm Front Shock Kit - requires #89554 shock shafts for RC8.2

16x29mm Front Shock Body

16mm Shock Caps

16x38mm Rear Shock Body

16x38mm Rear Shock Kit - requires #89554 shock shafts for RC8.2

16mm Shock Bladders

16mm Shock Rebuild Kit

16mm Shock Pistons

16mm Shock Spring Cups

16mm Shock Collars

HD Shock Ends

16mm Piston 5x1.1 + 5x1.2

HD Shock Shaft, 4x26mm

HD Shock Shaft, 4x36mm

RC8.2 Shock Boots (Front and Rear)

89353

89215

89492

Front

89554

Rear

89555

89278

89352

89355

89352

Front

89543

Rear

89547

89469

89354

89469

25612

:: Springs

89541

89542

89543

89544

89545

89546

89547

89548

RC8.2 Front Spring Kit

RC8.2 Front Spring Green (4.0lbs)

RC8.2 Front Spring Silver (4.3lbs) - Kit

RC8.2 Front Spring Blue (4.65lbs)

RC8.2 Rear Spring Kit

RC8.2 Rear Spring Green (3.25 lbs)

RC8.2 Rear Spring Silver (3.55 lbs) - Kit

RC8.2 Rear Spring Blue (3.75 lbs)

Pr.

2 ea.

:: Front and Rear Gear Differential

25236

89115

89116

89117

89120

89121

89208

89477

89478

89494

8x16x5 Bearings

Diff Housing

Diff Gasket

Diff Shims

Diff Sun/Planet Gears, Includes

Washers and Pins, Set

Diff 0-Rings, Big and Small, Set

3x14mm FHCS

RC8B Light Outdrive, Front

RC8B Light Outdrives, Rear

RC8B Light Diff Ring Gear, Includes Diff Gasket

89120

89121

89115

89120

89208

Front

89477

Rear

89478

89494

89208

89121

25236

89083

89116

89121

89335

89351

Front

89291

Rear

89344

89066

89352

25236

89109

89110

89115

89116

89119

89120

89121

89208

89372

89373

89374

89495

25236

89121

Front

89477

Rear

89478

:: Center Gear Differential

89120

8x16x5 Bearings

Spur Gear 44T, Includes Diff Gasket

Spur Gear 46T, Includes Diff Gasket

Diff Housing

Diff Gasket

Center Diff Outdrives

Diff Sun/Planet Gears, Includes

Washers and Pins, Set

Diff 0-Rings, Big and Small, Set

3x14mm FHCS

Spur Gear 50T, Includes Diff Gasket

Spur Gear 52T, Includes Diff Gasket

Spur Gear 54T, Includes Diff Gasket

Light Spur Gear 44T, Includes Diff Gasket - Kit

89556

89120

89121

89115

89120

89208

89119

25236

89121

Pr.

25236

89121

89119

89495

89116

89121

89120

:: Shock Fluid

5430

5431

5432

5433

5434

5435

5436

5437

5438

5420

5421

5422

5423

5424

5425

5426

5427

5428

5429

10 Weight Silicone Shock Fluid

20 Weight Silicone Shock Fluid

30 Weight Silicone Shock Fluid

40 Weight Silicone Shock Fluid

22.5 Weight Silicone Shock Fluid

80 Weight Silicone Shock Fluid

27.5 Weight Silicone Shock Fluid

15 Weight Silicone Shock Fluid

25 Weight Silicone Shock Fluid

35 Weight Silicone Shock Fluid

45 Weight Silicone Shock Fluid

55 Weight Silicone Shock Fluid

32.5 Weight Silicone Shock Fluid

37.5 Weight Silicone Shock Fluid

42.5 Weight Silicone Shock Fluid

50 Weight Silicone Shock Fluid

60 Weight Silicone Shock Fluid

70 Weight Silicone Shock Fluid

47.5 Weight Silicone Shock Fluid

2oz.

:: Top Plate

25202

89011

89039

89214

89227

89234

89236

89455

3x10mm FHCS

RC8 Body Mounts, Set

Hinge Pin Bushings, 1/2/3 dot, Set

4x12mm FHCS

3x28mm SHCS

Blue Aluminum Top Plate - Kit

Black Aluminum Top Plate (FT)

3x22mm FHCS

89455

89227

89214

89011

89214

:: Lubes & Adhesives / Decals / Misc.

1105

1596

1597

5450

5451

5452

5453

5454

5455

5456

5457

5458

5459

6588

6591

6636

6727

FT Green Slime Shock Lube

FT Locking Adhesive

FT Tire Adhesive, Medium

Silicone Diff Fluid 1000cst

Silicone Diff Fluid 2000cst

Silicone Diff Fluid 3000cst

Silicone Diff Fluid 5000cst

Silicone Diff Fluid 7000cst

Silicone Diff Fluid 10000cst

Silicone Diff Fluid 20000cst

Silicone Diff Fluid 30000cst

Silicone Diff Fluid 60000cst

Silicone Diff Fluid 100000cst

Black Grease - 4cc

S.Diff Lube - 4cc

Silicone Grease - 4cc

Servo Tape

716

717

3816

3820

3834

89559

Reedy 2009 Sticker Set

Reedy Powered Logo Decal

American Bumper Sticker

AE Logo Decal Sheet

AE Blue Embossed Logo Sticker

RC8.2 Decal Sheet

89039

:: Steering

25215 M3 Locknut

31404

89014

89015

89016

89117

89161

89214

89242

89455

89485

6x10mm Bearing

Steering Rack Post

Servo Saver, Set

Servo Saver Bolt, Nut, Spring, Set

Diff Shims

Steering Bearing Set

4x12mm FHCS

Steering Drag Link

3x22mm FHCS

Aluminum Steering Posts

31404

:: Center CVA’s

89103

89106

89221

89286

89557

89560

RC8 Center CVA Bone

RC8 Center CVA Rebuild Set

5x4mm Setscrew

RC8 Gearbox Input Cup, Aluminum

Pin Retainer O-Ring / Boot

RC8 Rear Center Drive Shaft +3mm

2 ea.

Front

89221

89106

89286

89103

89106

89557

89560

89106

Rear

89221

89557

89286

89106

89557

89016

89014

89161

25215

89242

25215

89015

89161

89117

89016

89455

89117

89016

31404

89485

89214

25202

89234

89236

31404

89014

89161

89015

89161

31404

89485

89214

:: Front Gearbox

25215

25236

31531

89017

89039

89114

89214

89217

89219

89224

89227

89230

89279

89460

89461

89466

89472

89474

89481

89482

89553

M3 Locknut

8x16x5 Bearing

3x6mm BHCS

FR/RR Gearbox

Hinge Pin Bushings, Set

Diff Pinion Gear

4x12mm FHCS

4x14mm FHCS

3x5mm Setscrew

3x16mm SHCS

3x28mm SHCS

Silver Cone Washer

3x45mm SHCS

RC8 Aluminum A-Plate

RC8 Aluminum B-Plate w/Pins, Set works with #89466

RC8B Inner Hinge Pins, 4mm-HMA, Set works with #89461

RC8B Front Bulkhead Spacer

3x22mm FHCS

RC8B Low B Plate - Kit works with #89482, 89553

RC8B Low B Plate Inserts - Kit works with #89481, 89553

RC8.2 FR Hinge Pins, TiN - Kit works with #89481, 89482

89227

89224

89219

89017

31531

89219

89217

89039

89460

89230

89472

89017

89114

25236

25215

89017

89482

89553

25215

89553

25215

25236

89214

89474

89482

89481

89039

89279

89230

:: Front Suspension

89077

89094

89095

89096

89102

89105

89162

89206

89207

89218

25215

25236

31520

89029

89032

89039

89040

89041

89074

89075

89076

89223

89225

89230

89269

89285

89317

89380

89454

89526

89549

89550

89558

91069

M3 Locknut

8x16x5 Bearing

2.5x6mm BHCS

Steering Block Bushings, Set

Caster Angle Bushings, Set

Hinge Pin Bushings, Set

RC8 Inner Hinge Pins, Set

RC8 Outer Hinge Pins, Set

Steering Rod Ends

RC8 Steering Ballstuds

RC8 Camber Rod Ends, Set

Chassis Brace Rod Ends, Set

Nyloc Wheel Hex Nuts (Blue)

RC8 Wheel Hex (Aluminum)

RC8 Wheel Hex Pins

RC8 Front/Rear CVA Bone

RC8 CVA Rebuild FR/RR, Set

15x21x4 Bearing

4x10mm BHCS

4x12mm BHCS

3x8mm Washer

3x8mm SHCS

3x24mm SHCS

Silver Cone Washer

Steel turnbuckle, 38mm

Front Stub Axle, Aluminum

RC8T Droop Screws

FT Machined Steering Blocks

3x12mm SHCS

50mm Steel Turnbuckle

RC8.2 Front Upper Arms

RC8.2 Front Arms

RC8.2 Caster Blocks

Shock Mount Pin, Steel

Pr.

89102

91069

89549

89105

89317

31520

89039

89040

89162

89269

89076

89285

89077

89074

89526

89230

89225

89558

89206

89029

25215

89380

89032

89029

89207

89218

25215

89074

89075

25236

89096

89094

89454

89095

89223

89041

89550

:: Rear Gearbox

25191

25215

25236

31531

89017

89039

89114

89214

89217

89219

89224

89227

89228

89230

89452

89462

89463

89466

3x18mm SHCS

M3 Locknut

8x16x5 Bearing

3x6mm BHCS

RC8 FR/RR Gearbox, Set

RC8 Hinge Pin Bushings, Set

RC8 Diff Pinion Gear

4x12mm FHCS

4x14mm FHCS

3x5mm Setscrew

3x16mm SHCS

3x28mm SHCS

3x40mm SHCS

Silver Cone Washer

3x50mm SHCS

RC8 Aluminum C - Plate

RC8 Aluminum D - Plate w/Pins, Set

RC8B Inner Hinge Pins, 4mm HMA, Set

89452

89463

89039

89466

89227

89230

25215

89017

89452

25236

89039

89039 89214

25191

89039

89462

89466

:: Rear Suspension

89107

89162

89219

89223

89269

89284

89317

89454

89474

89551

89561

91069

25215

25236

31520

89031

89033

89041

89076

89094

89095

89096

89102

89105

M3 Locknut

8x16x5 Bearings

2.5x6mm BHCS

RC8 Caster/Hub Spacers, Set

RC8 Hub Carriers

RC8 Outer Hinge Pins, Set

RC8 Camber Rod Ends, Set

Nyloc Wheel Hex Nuts (Blue)

RC8 Wheel Hex (Aluminum)

RC8 Wheel Hex Pins

RC8 Front/Rear CVA Bone

RC8 CVA Rebuild FR/RR, Set

RC8 Rear CVA Shield/Boot, Set

15x21x4 Bearing

3x5mm Setscrew

3x8mm SHCS

38mm Steel Turnbuckle

Rear Stub Axle, Aluminum

RC8T Droop Screws

3x12mm SHCS

3x22mm SHCS

RC8.2 Rear Arms

Rear Mud Guards

Shock Mount Pin, Steel

Pr.

25236

89228

89114

25215

89217

89219

89224

31531

89017

25215

89017

89102

89107

89561

89105

89454

89076

89269

89076

89474 89284

89107

89162

89031

25236

89454

25215

89033

89095

89096

89094

89223

89551 89454

91069

31520

89317

89041

:: Front Shock Tower

31531

89218

89225

89230

89454

89470

89473

89538

3x6mm BHCS

3x8mm Washer

3x24mm SHCS

Silver Cone Washer

3x12mm SHCS

RC8B Shock Tower Hinge Pin Bushings, Set

RC8B Steel Shock Stand-offs

RC8.2 Front Tower, Aluminum

:: Rear Shock Tower

25192

25215

25620

89011

89225

89230

89454

89473

89539

3x20mm SHCS

M3 Locknut

3x10mm SHCS

RC8 Body Mounts, Set

3x24mm SHCS

Silver Cone Washer

3x12mm SHCS

RC8 Steel Shock Standoffs

RC8.2 Rear Tower, Aluminum

89218

89454

89230

89538

89473

89470

31531

89454

31531

89470

89218

89225

89230

89473

89539

89225

89230

25215

89011

89230

89225

25215

25620

25192

89454

89230

25192

89230

89473

:: Chassis Braces

25215

89068

89069

89077

89209

89238

89239

89258

25215

M3 Locknut

RC8 Pivot Chassis Brace Set (Front)

RC8 Pivot Chassis Brace Set (Rear)

Chassis Brace Rod Ends, Set works with #89068, 89069

3x18mm FHCS

FT Aluminum Chassis Brace (Front)

FT Aluminum Chassis Brace (Rear)

RC8 Chassis Braces, Plastic - Kit

(Front, Rear)

89209

89258

Front

89258

25215

:: Center Bulkhead

25225

89019

89122

89123

89124

89214

89226

89250

89254

3x3mm Setscrew

RC8 Center Bulkhead, Set

RC8 Brake Pads, Set

Heatsink Brake Discs - Kit

RC8 Brake Cams/Levers, Set

4x12mm FHCS

3x26mm SHCS

Fiber Brake Rotors

Center Top Plate

89226

89226 89226

89226

89254

25225

89122

89124

89019

89124

89122

89019

89122

89123

89122

89209

89122

89123

89019

:: Radio Tray

6338

21173

25187

25203

31531

89003

89004

89005

89006

89208

89209

89214

89222

89229

89253

89454

89471

Antenna Tube and Cap

18T Body Clips

3x14mm BHCS

3x12mm FHCS

3x6mm BHCS

RC8 Receiver/Battery Box, Set

RC8 Receiver Box Pads, Set

Aluminum Antenna Mount, Set

RC8 Servo Mount Spacers, Set

3x14mm FHCS

3x18mm FHCS

4x12mm FHCS

2.5x8mm SHCS

Blue Countersunk Washers

Antenna Mount, Set

3x12mm SHCS

RC8.1 Forward Battery Box and

Radio Tray

89471

89209

89208

89229

89006

21173

89003

89004

89229

89006

89004

25203

21173

89454

89471

89454 25187

89214

31531

89003

25203

89471

89003

25203

89471

25203

89222

25203

6338

89253

89003

2308

25201

25215

25225

89007

89008

89078

89126

89202

89203

89205

89218

89267

:: Linkage

3x18mm BHCS

3x8mm FHCS

M3 Locknut

3x3mm Setscrew

Steering Servo Horns, Set

Throttle Servo Horns, Set

RC8 Servo Link Rod Ends, Set

RC8 Linkage Set

3x12mm BHCS

3x16mm BHCS

3x26mm BHCS

3x8mm Washer

25215

89205

89078

89267

89078

2308

25215

25225

89126

25225

25201

89007

89126

25225

89126

89007

25215

89126

25201

89008

89218

89008 89202

89126

89126 89126

25225

89126

89078

25215

89203 89008

:: Chassis

25201

25226

89018

89022

89130

89144

89145

89207

89213

89224

89231

89257

89476

89552

3x8mm FHCS

4x5mm Setscrew

RC8 Gearbox Gasket

RC8 Front Bumper

RC8 Engine Mount Plates

RC8 Pipe Mount

RC8 Pipe Mount Wire

4x12mm BHCS

4x6mm FHCS

3x16mm SHCS

3mm Lock Washer

RC8 Engine Mount

RC8B +3mm Chassis

RC8.2 Side Guards

89224

89231

89224

89231

89257

89130

89207

89231

89257

89130

89207

Pr.

89018

25201

89022

89213 89213

:: Anti-Swaybars

25192

25225

89487

89488

89489

89490

89530

89531

89532

89533

89534

89535

89536

89537

3x20mm SHCS

3x3mm Setscrew

RC8B RR Swaybar, 2.5 (Green) - Kit

RC8B RR Swaybar, 2.6 (White)

RC8B RR Swaybar, 2.7 (Blue)

RC8B RR Swaybar, 2.8 (Yellow)

RC8.2 FR Swaybar Kit

RC8.2 RR Swaybar Kit

RC8.2 FR Swaybar, 2.2 (Green)

RC8.2 FR Swaybar, 2.3 (White) - Kit

RC8.2 FR Swaybar, 2.4 (Blue)

RC8.2 FR Swaybar, 2.5 (Yellow)

RC8.2 Swaybar Pivot Ball

RC8.2 Swaybar Drop Link

25225

89536

25192

25226

89144

25201

89552

25201

89145

25201

89018

:: Wing

25192

25204

25215

89229

89304

89540

3x20mm SHCS

3x16mm FHCS

M3 Locknut, (Black)

Blue Countersunk Washer

JC Illuzion Wing (Black)

RC8.2 Wing Mount, Set

25204

89304

89229

25204

89229

89552

89476

25201

89537

Front

89532

89533

89534

89535

Rear

89487

89488

89489

89490

25225

89536

89537

25192

89540

25215

89540

25215

89540

25192

:: Wheels / Tires

89152

89153

89255

89296

89297

RC8 Wheels (White)

RC8 Wheels (Yellow)

RTR Pre-Glued Wheel/Tire (White)

RC8 83mm Wheels (White) - Kit

RC8 83mm Wheels (Yellow)

:: Fuel Tank

21173

25203

89066

89128

89131

89325

18T Body Clips

3x12mm FHCS

Shock O-Rings

Fuel Tank Mount, Set

RC8 Fuel Tank

Fuel Line Clips, Set

89325

21173

89066

89128

25203

89255

Pr.

:: Body / Decals

1737

2208

31531

89150

89275

89276

89277

89475

89523

89559

FT Body Scissors

Large Hood Pins

3x6mm BHCS

RC8 Body w/Window Mask (Clear)

RC8 RTR Body (Black)

RC8 RTR Body (White)

RC8 RTR Body Wrap Decals

RC8B Decal Sheet

RC8e Body w/Window Masks (Clear)

RC8.2 Decal Sheet

2208

89150

2208

31531

:: Air Filter

3719

7710

25201

89139

89140

89141

89142

6” Nylon Wire Ties

Pre-Filter Fluid

3x8mm FHCS

RC8 Air Filter Set

RC8 Air Filter Hose

Air Filter Elements

Air Filter Outer Elements

21173

89131

89066

89128

25203

89139

25201

89142

89141

89140

:: Clutch

25237

89127

89132

89133

89134

89135

89136

89137

89138

89148

89157

89158

89159

89218

89223

89265

89375

89376

5x10x4 Bearings

Clutch Bell, 17T

Clutch Bell, 16T - Kit

Clutch Springs 1.0 - Kit

Clutch Shoes w/ Shims, Set

Clutch Nut

Flywheel (Hard Anodized)

Clutch Shims

Flywheel Collet

Clutch Bell Shim Set

0.9 Clutch Springs

1.1 Clutch Springs

Short Clutch Nut

3x8mm Washer

3x8mm SHCS

Fiber Clutch Shoes

Clutch Bell, 14T

Clutch Bell, 13T

89148

89223

89138

89134 89135

89132

89148

25237 25237

89137

89133

89136

89218

:: Exhaust

2357

25094

89175

89176

89177

89178

89181

Rear Exhaust Manifold Spring

Header Spring

Black Non-Stick Muffler

Black Non-Stick Header

Polished Muffler

Polished Header

Muffler to Header Springs

89175

89176

2357

:: Fueling

1748

1749

7724

7725

25076

Nitro Fuel Bottle 600cc

Nitro Fuel Bottle 350cc

Fuel Line 15”

Fuel Line 3’

Fuel Primer Bulb

:: Starting Equipment

1738

1750

7994

25261

25262

89439

FT Glow Starter

FT Starter Box

D-Size Glow Ignitor

Hex Drive Starter Shaft

Pro Start Starter

Hex Drive Starter Shaft XL (SC8)

7724

7725

1748

1749

25076

1750

:: Factory Team and Option Parts

89456

89460

89461

89462

89463

89464

89465

89466

89470

89473

89237

89238

89239

89284

89285

89286

89380

89381

89405

89406

89073

89082

89123

89136

89146

89161

89229

89234

89235

89236

25392

80930

89005

89012

89016

89020

89045

89068

89069

89070

89071

89476

89477

89478

89481

89482

89483

89484

89485

3mm Blue Locknut, Flanged

1/8 Scale Electric Conversion Kit

Aluminum Antenna Mount

RC8 Steering Rack, Carbon Fiber

Servo Saver Bolt, Nut, Spring

Center Bulkhead Plate CF

RC8 FT 0.5 Degree Toe Bushing

RC8 Pivot Chassis Brace Set (Front)

RC8 Pivot Chassis Brace Set (Rear)

RC8 Ti Turnbuckle Set

Camber Turnbuckles 5mm

Servo Turnbuckle 4mm

RC8 Shock Standoffs, Aluminum

RC8 Heatsink Brake Disc

RC8 Flywheel, Hard

RC8/T Clutch Shoes, Hard

Steering Bearing Set

Blue Countersunk Washer

Blue Aluminum Top Plate (FT)

RC8 CNC Aluminum Steering Rack

Black Aluminum Top Plate (FT)

RC8 Skid Plate

FT Aluminum Chassis Brace (Front)

FT Aluminum Chassis Brace (Rear)

RC8 Rear Stub Axle (Aluminum)

RC8 Front Stub Axle (Aluminum)

RC8 Gearbox Input Cup (Aluminum)

RC8 FT Machined Steering Blocks

RC8 FT Machined Rear Hubs

Nyloc Wheel Nuts (Silver)

Nyloc Wheel Nuts (Black)

16mm Piston 10x1.1

RC8 Aluminum A-Plate

RC8 Aluminum B-Plate w/Pins, Set

RC8 Aluminum C-Plate

RC8 Aluminum D-Plate w/Pins, Set

RC8B Aluminum Front Shock Tower

RC8B Aluminum Rear Shock Tower

RC8B Inner Hinge Pins, 4mm HMA, Set

RC8B Shock Tower Hinge Pin Bushings, Set

Steel Shock Standoff

FT RC8B +3mm Chassis

FT RC8B Light Outdrive, Front

FT RC8B Light Outdrive, Rear

FT RC8B Low B-Plate

FT RC8B Low B-Plate Inserts

FT RC8B Front Shock Tower

FT RC8B Rear Shock Tower

FT RC8B Aluminum Steering Posts

Pr.

29170

29171

29172

29173

29174

29175

29176

29178

29187

29189

29155

29156

29158

29160

29161

29162

29164

29165

29166

29167

29200

29202

29206

29209

29210

29211

29212

29221

29222

:: XP Electronics

29102

29107

29108

29109

29110

29111

29112

29113

29115

29122

29123

29124

29125

29126

29130

29131

29132

29150

Antenna (silver) xp2/xp3/xp3d

Metal gear set, S1903/S1903MG

AM TX + RX crystal set, 26.995 Ch 1

AM TX + RX crystal set, 27.045 Ch 2

AM TX + RX crystal set, 27.095 Ch 3

AM TX + RX crystal set, 27.145 Ch 4

AM TX + RX crystal set, 27.195 Ch 5

AM TX + RX crystal set, 27.255 Ch 6

BEC switch with harness, TR-404A

Receiver, AM 27MHZ 2ch, TR202A

Receiver, AM 27MHZ 4ch, TR402A

S1903 standard servo

S1903MG standard servo, metal gear

S2008MG high torque servo, metal gear

Micro receiver, AM 27MHZ 2ch, TR204A

SHV1504 servo

SHV1504MG servo

Charger for xp2/xp3/xp3d & receiver packs (not for LiPo)

XP3D FM Radio System 27mHz

XP3D FM Radio System 75mHz

XP3D 3ch Digital Transmitter Only

Transmitter RF module, AM 27MHZ

Transmitter RF module, FM 27MHZ

Transmitter RF module, FM 75MHZ

Receiver, FM 27MHZ 3ch, TR301F

Receiver, FM 75MHZ 3ch, TR301F

DS1313 performance digital servo

DS1015 hi-torque/hi-speed digital servo

FM TX + RX crystal set, 26.995 Ch 1

FM TX + RX crystal set, 27.045 Ch 2

FM TX + RX crystal set, 27.095 Ch 3

FM TX + RX crystal set, 27.145 Ch 4

FM TX + RX crystal set, 27.195 Ch 5

FM TX + RX crystal set, 27.255 Ch 6

FM TX + RX crystal set, 75.410 Ch 61

FM TX + RX crystal set, 75.450 Ch 63

FM TX + RX crystal set, 75.630 Ch 72

FM TX + RX crystal set, 75.670 Ch 74

FM TX + RX crystal set, 75.890 Ch 85

FM TX + RX crystal set, 75.930 Ch 87

Receiver, AM 27MHZ 4ch, TR405A

Gear set, DS1313 digital servo

Gear set, DS1015 digital servo

Servo case, DS1313/DS1015

Accessory pack

XP3SS 2.4GHz Radio System

TRS401SS 2.4GHz 4Ch Receiver

:: LRP Engines, Chargers, Soldering Irons

LRP32111

LRP41281

LRP41555

LRP42305

LRP43150

LRP45200

LRP65800

LRP65802

LRP65803

LRP65804

ZR.21X Spec.2 Non Pull Race Engine

Quadra Pro 2 Charger

Pulsar Touch Competition Charger

Pulsar Touch Temperature Sensor

Power Supply Competition

LiPo Parallel Balancer

High Power Solder Station

Soldering Tip 5mm

Soldering Tip 1.2mm

Soldering Handle

:: LRP 1/8 Brushless Systems

LRP53230

LRP53240

LRP53270

LRP80785

LRP80786

LRP80787

LRP80880

Dynamic 8 Brushless Motor 1800KV

Dynamic 8 Brushless Motor 2200KV

Dynamic 8 Brushless Motor 2600KV

IX8/Dynamic 8 2600KV

IX8/Dynamic 8 2200KV

IX8/Dynamic 8 1800KV

IX8 Brushless ESC

:: Reedy Nitro Engines and Parts

28027

28028

28029

28030

28031

28032

28033

28034

28035

28036

28017

28018

28019

28020

28021

28022

28023

28024

28025

28026

800

801

28000

28001

28002

28003

28004

28005

28006

28007

28008

28009

28010

28011

28012

28013

28014

28015

28016

28037

28038

28039

28040

28041

28042

28043

28044

28045

28046

28047

28048

28049

28050

Reedy 121VR .21 Off-Road Comp. Nitro Engine

Reedy 121VR-ST .21 Comp. Nitro Engine

121 VR Crankshaft

121 Crankcase

121 Connecting Rod

121 Wrist Pin

121 Circlips

121 VR Cylinder & Piston

121 VR Heatsink Head

121 VR Button

121 Carb Insulator

121 Head Shim Set

121 Backplate

121 Exhaust Gasket

121 Ball Bearing (Rear)

121 Ball Bearing (Front)

121 Screw Set

121 VR Complete Carburetor

121 VR Carb Body Set

121 Needle Valve Assembly

121 Needle Valve

121 Carb Slide Assembly

121 Idle Screw

121 VR O-Ring Set

121 Exhaust Spring Set

121 Dust Cap Set

121 Flywheel Collet

121 Restrictor (7.0mm)

121 Restrictor (8.0mm)

121 Restrictor (9.0mm)

121 Restrictor (6.5mm)

121 Restrictor (7.5mm)

121 Restrictor (8.5mm)

121 VR-ST Crankshaft (ADLC)

121 VR-ST Crankcase

121 Wrist Pin (ADLC)

121 VR-ST Cylinder and Piston

121 VR-ST Heatsink Head

Ceramic Rear Bearing for 121 Engine

121 VR-ST Complete Carburetor

121 VR-ST Carburetor Body Set

121 VR-ST Midrange Screw

Reedy RT3 Turbo Plug, Very Hot

Reedy RT4 Turbo Plug, Hot

121 Restrictor (5.0mm)

121 Restrictor (5.5mm)

121 Restrictor (6.0mm)

Reedy 2035 Tuned Exhaust System

Reedy 2035 Muffler

Reedy Exhaust Manifold

Reedy 2039 Tuned Exhaust System

Reedy 2039 Muffler

Reedy Turbo Glow Plug Caddy

:: Reedy Accessories

604

606

607

610

715

716

SP35M

SP35L

SP35XL

SP35XXL

SP35XXXL

SP36M

SP36L

SP36XL

SP36XXL

SP36XXXL

SP417

526-S AC/DC 2S-6S LiPo/LiFe Charger

Charge Harness 2S Saddle Pack 4mm

Charge Harness 2S Standard Pack 4mm

447-S AC/DC NiMH Peak Charger

Reedy 2009 Banner

Reedy 09 Decal Set

Reedy Logo T-Shirt - White M

Reedy Logo T-Shirt - White L

Reedy Logo T-Shirt - White XL

Reedy Logo T-Shirt - White XXL

Reedy Logo T-Shirt - White XXXL

Reedy Logo T-Shirt - Black M

Reedy Logo T-Shirt - Black L

Reedy Logo T-Shirt - Black XL

Reedy Logo T-Shirt - Black XXL

Reedy Logo T-Shirt - Black XXXL

Factory Team 1/10 Motor Storage Bag

:: Reedy Batteries

633

634

635

636

637

638

693

694

695

700

302

303

304

305

612

613

630

631

632

720

721

722

733

AA Alkaline 1.5V (4)

AA 2700mAh NiMH 1.2V Rechargeable

Pro RX Battery 1600mAh 7.4V Flat

Pro RX Battery 1300mAh 6.6V Flat

1600 Series 6.0V Hump Receiver Pack

1600 Series 6.0V Flat Receiver Pack

Pro RX LiPoBattery 1600mAh 7.4V

RX LiPo Battery 2100mAh 7.4V

TX Lightweight Battery 1350mAh 11.1V

TX Battery - 3PK, M11 3000mAh 11.1V

TX Battery - Helios, Z1 2400mAh 11.1V

Starter Box Battery 2200mAh

6.0V Voltage Regulator

TX Battery - M11X 2500mAh 7.4V

RX LiFe Battery 1700mAh 6.6V

Wolfpack 2400mAh 7.2V w/TAM connector

Wolfpack 3000mAh 7.2V w/TAM connector

Wolfpack 3600mAh 7.2V w/TAM connector

Wolfpack 4200mAh 7.2V w/TAM connector

LiPo 14.8V 5000mAh 40C

LiPo 22.2V 3100mAh 6S 40C

LiPo 18.5V 3800mAh 5S 40C

Wolfpack LiPo 3700mAh 14.8V 35C w/DEANS®

:: Apparel

SP35**

SP36**

SP58**

SP59**

SP62**

SP63**

SP64**

SP65**

SP66**

SP67**

SP101

SP102

SP103

SP411S

SP411L

SP416

SP417

SP420**

715

110684

Reedy 09’ White T-Shirt (M, L, XL, 2XL, 3XL)

Reedy 09’ Black T-Shirt (M, L, XL, 2XL, 3XL)

AE Logo Black T-Shirt (M, L, XL, 2XL)

AE Logo Blue T-Shirt (M, L, XL, 2XL)

AE Vertigo Long Sleeve T-Shirt (S, M, L, XL, 2XL)

AE Vertigo White T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)

AE Vertigo Blue T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)

AE Vertigo Black T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)

AE Stencil Blue T-Shirt (S, M, L, XL, 2XL, 3XL)

AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL)

1/8 Inner Boxes Only, Set

1/10 Inner and Outer Boxes Only, Set

1/10 Inner Boxes Only, Set

AE Hat 11’ Flatbill Black S/M

AE Hat 11’ Flatbill Black L/XL

1/10 Car Carrier Bag Only

1/10 FT Motor Bag

AE Pit Gloves (M, L, XL)

Reedy 2009 Track Banner

Team Associated Track Banner

Pr.

** Use part number plus the desired size when ordering!

:: 1/18 Kits and RTR’s

20100

20101

20103

20105

20106

20110

20115

20118

20120

20121

20130

RC18T RTR (ready-to-run)

RC18T2 2.4ghz RTR (ready-to-run)

RC18B2 - RC18T2 Team Kit

RC18B RTR (ready-to-run)

RC18B2 2.4ghz RTR (ready-to-run)

RC18MT RTR (ready-to-run)

RC18R Kamino RTR (ready-to-run)

RC18R Niteline RTR (ready-to-run)

SC18 RTR (ready-to-run)

SC18 Brushless RTR (ready-to-run)

RC18LM RTR (ready-to-run)

:: 1/12, 1/10 Kits and RTR’s

7037

7046

7047

7048

7049

7080

7092

8020

8021

9036

2033

2042

4019

7023

7027

7029

7030

7032

7034

7036

9039

9061

20515

30105

30106

30111

90004

90005

90006

90007

FT Nitro TC3 Kit

Nitro TC3 RTR Plus (ready-to-run)

FT 12R5.1 Kit

RC10T4.1 FT Kit

SC10 2WD Short Course Race Truck Kit

SC10 Associated/RC10.com Truck RTR (ready-to-run)

SC10 KMC Wheels Race Truck RTR (ready-to-run)

SC10 Ready Lift RTR (ready-to-run)

SC10 FT Kit

RC10T4.1 RTR 2.4GHz Brushed (ready-to-run)

RC10T4.1 RTR 2.4GHz Brushless (ready-to-run)

SC10RS RTR, 2.4ghz Brushless Lucas Oil Body

SC10RS RTR, 2.4ghz Brushless Monster Energy Body

SC10RS RTR, 2.4ghz Brushless Pro Comp Body

SC10RS RTR, 2.4ghz Brushless Rockstar/Makita Body

FT GT2 Nitro Truck Kit

GT2 RS Truck Nitro RTR (ready-to-run)

FT RC10R5 Kit

FT RC10R5-OVAL Kit

RC10B4.1 FT Kit

RC10B4.1 RTR 2.4GHz Brushless (ready-to-run)

FT B44.1 4WD Buggy Kit

MGT 3.0 Nitro Monster Truck RTR (ready-to-run)

FT TC5R Rubber Tire Edition 4WD Touring Car Kit

FT TC6 4WD Touring Car Kit

TC4 4WD Touring Car RTR (ready-to-run)

SC10 4X4 Kit

SC10 4X4 RTR, 2.4ghz Brushless Lucas Oil Body

SC10 4X4 RTR, 2.4ghz Brushless Pro Comp Body

SC10 4X4 RTR, 2.4ghz Brushless Rockstar/Makita Body

:: 1/8 Kits and RTR’s

20503

20504

80902

80904

80905

80906

80912

80922

80923

80924

80925

80932

Limited Edition MGT 4.60 Nitro RTR, w/flag body

(ready-to-run)

Limited Edition MGT 8.0 Nitro RTR, w/flag body

(ready-to-run)

FT RC8B Nitro Buggy Kit

FT RC8Be Electric Buggy Kit

RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)

FT RC8.2 Nitro Buggy Kit

RC8T Championship Edition

SC8 Short Course Race Truck, KMC Wheels Nitro RTR

(ready-to-run)

SC8 Short Course Race Truck, Bully Dog Nitro RTR

(ready-to-run)

SC8 Short Course Race Truck, AE Team Nitro RTR

(ready-to-run)

SC8 Short Course Race Truck, Pro Comp Nitro RTR

(ready-to-run)

SC8e Short Course Race Truck Rockstar/Makita RTR

(ready-to-run)

1719

1737

3718

3719

3720

3987

6429

6956

7494

7709

91107

:: Tools

1662

1663

1664

1665

1666

1667

1668

1669

1670

1671

1672

1673

1674

1589

1590

1592

1655

1656

1657

1658

1659

1660

1661

1551

1553

1554

1561

1562

1563

1564

1565

1566

1567

1111

1112

1449

1450

1541

1542

1543

1544

1545

1546

1547

1548

FT Turnbuckle Wrench

FT 4mm Turnbuckle Wrench (4x4 only)

Offroad Ride Height Gauge

FT Ride Height Gauge

FT Hex Driver Set, (7 pcs)

FT .050” Silver Hex Driver

FT 1/16” Black Hex Driver

FT 1.5mm Purple Hex Driver

FT 5/64” Blue Hex Driver

FT 3/32” Gold Hex Driver

FT 2.5mm Green Hex Driver

FT 3mm Red Hex Driver

FT Screwdriver Set

FT Phillips Silver Screwdriver

FT Silver Spring Hook Tool

FT Nut Driver Set, (6 pcs)

FT 3/16” Black Nut Driver

FT 1/4” Red Nut Driver

FT 5.5mm Red Nut Driver

FT 11/32” Green Nut Driver

FT 7.0mm Silver Nut Driver

FT 8mm Gold Nut Driver

FT 5/64” Blue Ball Hex Driver

FT 3/32” Gold Ball Hex Driver

FT Ball Hex Driver Set, (3 pcs)

FT 8-Piece 1/4” Hex Drive Set

FT 1/4” Hex Drive Handle, without tips

FT 1/4” Hex Drive .050” Tip

FT 1/4” Hex Drive 1/16” Tip

FT 1/4” Hex Drive 5/64” - 2.0mm Tip

FT 1/4” Hex Drive 3/32” Tip

FT 1/4” Hex Drive 1.5mm Tip

FT 1/4” Hex Drive 2.5mm Tip

FT 1/4” Hex Drive 3/16” Nut Driver Tip

FT 1/4” Hex Drive 1/4” Nut Driver Tip

FT 1/4” Hex Drive 11/32” Nut Driver Tip

FT 1/4” Hex Drive 5.5mm Nut Driver Tip

FT 1/4” Hex Drive 7.0mm Nut Driver Tip

FT 1/4” Hex Drive 8.0mm Nut Driver Tip

FT 1/4” Hex Drive 5/64” - 2.0mm Ball End Tip

FT 1/4” Hex Drive 3/32” Ball End Tip

FT 1/4” Hex Drive Standard Screwdriver Tip

FT 1/4” Hex Drive Phillips Screwdriver Tip

FT 1/4” Hex Drive 2.5mm Ball End Tip

FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm,

1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)

FT Camber + Track Width Tool

FT Body Scissors

12 Inch Nylon Wire Ties

6 Inch Nylon Wire Ties

8 Inch Nylon Wire Ties

FT Droop Gauge

Shock Building Tool

Molded Tools, Set

V2 Stamped Multi Tool

4 Inch Nylon Wire Ties

13mm Shock Tools

:: Contact Information

Associated Electrics, Inc.

26021 Commercentre Drive

Lake Forest, CA 92630-8853 USA http://www.TeamAssociated.com http://twitter/Team Associated http://www.RC10.com

http://bit.ly/AEonFacebook call: (949) 544-7500 fax: (949) 544-7501

Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info!

www.TeamAssociated.com. - www.RC10.com

:: Notes

Front Suspension

Steering System:

Swing Rack

Bellcrank Rack

Bumpsteer

Washers:

Camber:

Caster:

Toe: 0

B A

-1

Setup Sheet

Anti Roll Bar:

2.2mm Green

2.3mm White

2.4mm Blue

2.5mm Yellow

O I

Ride Height: 28mm

Front Shocks

Spring:

Piston:

Silver 4.3

Shock Fluid: 30 weight

1.2

Chassis Braces / Wheel Hex

Chassis Braces:

Pivot

Molded

Aluminum

Wheel Hex:

Standard

Narrow

Body / Wing

Body Type:

Wing Type:

JConcepts

Gap to Tower (MM):

Tires

Tire (F/R):

Compound (F/R):

Inserts (F/R):

Wheel (F/R):

Notes:

24mm

Race and Vehicle Comments

Qualify:

Comments:

Main:

Driver:

Track:

RC8.2 FT Standard Setup

Conditions:

Rear Suspension

Wheelbase:

Long

Medium

Short

Anti Roll Bar:

Date:

Event:

Rev.1

Upper Hinge

Pin Bushing

2.5mm Green

2.6mm White

2.7mm Blue

2.8mm Yellow

Front # 1 dot

Up Down

Camber:

B A C

-1

Rear # 3 dot

Up Down

Toe Bushing

D-Plate

B-Plate Type

Low Original

1 dot

In Out

Kickup Bushing

A-Plate

Hub:

Upper

Lower

Squat Bushing

C-Plate

# 2 dot

Up Down Ride Height:

29mm

2 dot

Up Down

Shock Cap:

Length:

Rebound:

Alum.

106mm

None

Rear Shocks

Spring:

Shock Fluid:

Piston:

Silver 3.55

30 weight

1.2

Shock Cap:

Length:

Rebound:

Alum.

122mm

None

Chassis Weight

Weight:

Rear Hubs

Rear Hubs:

Differentials

Front Diff Fluid:

Center Diff Fluid:

Rear Diff Fluid:

5,000

Standard

CNC FT Alum.

Gearing / Clutch

Spur Gear:

Clutch Bell:

Clutch Shoes:

Clutch Spring:

44T - Light

16T std

1.0

Engine

Engine:

Restrictor:

Muffler:

Temp:

Glow Plug: Fuel:

Radio / Servos

Radio:

Throttle / Brake expo:

Steering expo:

Dual Rate:

Throttle / Steering Servo:

Brake Bias:

Track Info

Finish: TQ: Traction: High Medium Low

Surface: Smooth Bumpy Blue Groove

Soft Dirt Grass Clay Wet

Astroturf Dusty Other:

:: For more setups, visit RC10.com and click on “Setup Sheets”

:: Hardware - 1:1 Scale View

Flat Head (fhcs)

3x8mm (25201)

Cap Head (shcs)

2.5x8mm (89222)

Button Head (bhcs)

2.5x3mm (89201)

3x10mm (25202)

3x12mm (25203)

3x8mm (89223)

3x10mm (25620)

2.5x6mm (31520)

3x6mm (31531)

Ball Bearings

3x14mm (89208)

3x18mm (89209)

3x20mm (89210)

3x22mm (89455)

3x26mm (89211)

4x6mm (89213)

4x12mm (89214)

4x14mm (89217) steering bearing

(89161)

5x10mm (25237)

6x10mm (31404)

8x16mm (25236)

15x21mm (89162)

Set Screws

3x12mm (89454)

3x16mm (89224)

3x18mm (25191)

3x20mm (25192)

3x22mm (89474)

3x24mm (89225)

3x26mm (89226)

3x28mm (89227)

3x40mm (89228)

3x45mm (89279)

3x10mm (25211)

3x12mm (89202)

3x14mm (25187)

3x16mm (89203)

3x18mm (2308)

3x20mm (25188)

3x24mm (89204)

3x26mm (89205)

4x10mm (89206)

4x12mm (89207)

3x50mm (89452) Shims and Washers

3mm lock washer (89231)

2.5mm washer (89278)

3x3mm (25225)

3x5mm (89219)

4x5mm (25226)

4x12mm (89220)

5x4mm (89221) blue countersunk washer

(89229) silver cone washer (89230)

3x8mm thin washer

(89218) diff washer (89120) diff shim (89117)

Front Suspension

Steering System:

Setup Sheet

Driver:

Track:

Conditions:

Rear Suspension

Wheelbase:

Date:

Event:

Rev.1

Swing Rack

Bellcrank Rack

Bumpsteer

Washers:

Camber:

Caster:

Toe:

B A

Anti Roll Bar:

2.2mm Green

2.3mm White

2.4mm Blue

2.5mm Yellow

O I

Ride Height:

Front Shocks

Spring:

Shock Fluid:

Piston:

Chassis Braces / Wheel Hex

Chassis Braces:

Pivot

Molded

Aluminum

Wheel Hex:

Standard

Narrow

Body / Wing

Body Type:

Wing Type:

Gap to Tower (MM):

Tires

Tire (F/R):

Compound (F/R):

Inserts (F/R):

Wheel (F/R):

Notes:

Race and Vehicle Comments

Qualify:

Comments:

Main:

Long

Medium

Short

Anti Roll Bar:

Upper Hinge

Pin Bushing

2.5mm Green

2.6mm White

2.7mm Blue

2.8mm Yellow

Front #

Up Down

Camber:

B A C

Rear #

Up Down

Toe Bushing

D-Plate

B-Plate Type

Low Original

In Out

Kickup Bushing

A-Plate

Hub:

Upper

Lower

Squat Bushing

C-Plate

O I

Up Down Ride Height:

Up Down

Shock Cap:

Length:

Rebound:

Chassis Weight

Weight:

Gearing / Clutch

Spur Gear:

Clutch Bell:

Clutch Shoes:

Clutch Spring:

Finish: TQ:

Rear Shocks

Spring:

Shock Fluid:

Piston:

Shock Cap:

Length:

Rebound:

Rear Hubs

Rear Hubs:

Differentials

Front Diff Fluid:

Center Diff Fluid:

Rear Diff Fluid: Standard

CNC FT Alum.

Engine

Engine:

Restrictor:

Muffler:

Temp:

Glow Plug: Fuel:

Radio / Servos

Radio:

Throttle / Brake expo:

Steering expo:

Dual Rate:

Throttle / Steering Servo:

Brake Bias:

Track Info

Traction: High Medium Low

Surface: Smooth Bumpy Blue Groove

Soft Dirt Grass Clay Wet

Astroturf Dusty Other:

:: For more setups, visit RC10.com and click on “Setup Sheets”

Hello! I am an AI chatbot specifically trained to assist you with the Associated Electrics RC82 Manual & Catalog. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!