Rosewill Power Supply, Turbo Series User Manual
Advertisement
Advertisement
POWER SUPPLY Turbo series User Manual
Content
• Features Descriptions..............................................
P2
• Specification............................................................
P3
• Installation................................................................
1. Installing Power Supply.......................................
2. 20+4 pin Main Connector....................................
3. 4+4 pin Connector...............................................
4. 6 pin PCI-Express Connector..............................
5. 4 pin Molex Connector........................................
6. 4 pin Floppy Connector.......................................
7. 5 pin SATA Connector.........................................
8. Before starting your system................................
P6
P6
P7
P8
P8
P8
P8
P9
• Information...............................................................
P10
1
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
POWER SUPPLY Turbo series
Features Descriptions
• ATX V2.2 Dual 12V Rails • Extreme 135mm cooling Fan
User Manual
• 20+4 pin Main Connector • 4/8-pin +12v and EPS Connector
• Dual PCI-Express Connectors for your SLI • Four SATA Connectors
• Mirror Titanium Finish • All cables with black mesh sleeving
2
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
POWER SUPPLY Turbo series
Input
• AC Input Voltage : 115V/230V
• AC Input Frequency : 50/60HZ
• AC input Current : 8.8A (RMS) for 115VAC Input
5.7A (RMS) for 230VAC Input
User Manual
Output
Voltage +3.3V +5V +12V1 +12V2 -12V -5V +5VSB
MAX.Current 30A 25A 17A 18A 0.6A 0.6A 2.5A
MAX.Watt 160W 368W 7.2W
Total Watt 550W
3W 12.5W
Regulation ±5% ±5% ±5% ±5% ±10% ±10% ±5%
& 100 100 120 120 200 200 100
Overall Performance
Total Output Power : Full Load 550W at normal input voltage
Efficiency : 70% typical at full load and normal input voltage
Hold-Up Time : 17ms at full load and normal input voltage
Switching Frequency : 60HZ at normal input.
Stability : ±10%, for 12 hours after warm up.
Protection
Over Power Protection
• The whole output power is limited by over power protection. It is raging from
110% to 150% of normal rated output power.
Over voltage protection
Output Voltage
+3.3V
Min(V) Max(V)
3.9 4.5
+5V 5.7
+12V1, +12V2 13.3
6.5
14.5
+5VSB 5.7 6.5
Short Circuit Protection
Output power +3.3V, +5V, +12V are all protected by circuit protection.
4
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
POWER SUPPLY Turbo series
Environment
Operation Temperature : 0°c to +40°c
Storage Temperature : 0°c to +80°c
Operating Humidity : 10% to 90% RH
Storage Humidity : 10% to 90% RH
Safety standards
TUV/CE/CB/FCC/UL
EMI Standard
Meet FCC class B and FTZ. standard.
HI-POT Testing
Input to ground : 15KVac/10mA 3 second
Input to output : 15KVac/10mA 5 second
Insulation resistance
Input to ground : Min 50M ͈
Input to output : Min 50M ͈
Reliability
MTBF : 100000 hours at 25°c ambient temperature.
User Manual
5
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
POWER SUPPLY Turbo series
Installation
1.Installing Power supply
Affix the power supply to the case with screws.
User Manual
2. 20+4 pin Main Connector
20pin
• Detach the 4 pin connector to
have a 20 pin main connector
24pin
• Attach the 4 pin connector to have
a 24 pin main connector
• Plug the 20 pin connector onto
the motherboard.
• Plug the 24 pin connector onto the
motherboard.
NOTE :
1.Confirm 20 pin or 24 pin main connector your motherboard needs before the
installation.
2. 4 pin here is used for switching between 20 & 24 pin only.
6
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
POWER SUPPLY Turbo series
3. 4+4 pin Connector
4 pin
• Separate the 8 pin EPS +12V
connector to have two 4 pin
connector
User Manual
8 pin
• Combine two 4 pin connectors
to have a 8 Pin EPS +12V
connector
• Pick anyone 4 pin +12V
connector to plug onto the
motherboard
• Plug the 8 pin EPS +12V
connector onto the
motherboard.
NOTE :
1.Confirm 4 pin +12V or 8 pin EPS +12V connector your motherboard needs before
the installation.
2.4 pin here CAN NOT be used for the main connector.
7
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
POWER SUPPLY Turbo series
4. 6 pin PCI-Express Connector
The 6 pin PCI-Express connector for video card only.
NOTE :
Confirm if your video card needing the 6 pin
PCI-Express connector or not before the installation.
Not every video card needs it.
5. 4 pin Molex Connector
The 4 pin Molex connector used for HDD,
Optical Drive and other devices needing it.
6. 4 pin Floppy Connector
The 4 pin Floppy connectors used for Floppy disk
or Zip drives.
.
7. 5 pin SATA Connector
5 pin SATA connector used for SATA HDD and
Optical Drive
8
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
User Manual
POWER SUPPLY Turbo series
8. Before starting your system
Select the proper voltage setting.
( Setting for United States is 115 Volt )
Attach the power core to the power supply
Connect the power core to a power source.
Confirm the power supply is on on
9
© 2004-2006 Rosewill Inc. All rights reserved by Rosewill off
User Manual

Public link updated
The public link to your chat has been updated.
Advertisement