AVAILABLE REPAIR KITS
Rotary Head Kit - Major:
P/N 2100372 (DCFSCP20GZ)
P/N 2100373 (CDFSCP20)
Includes items 2, 3, 4, 5, 6, 7, 8, 9,
10, 11, 12, 13, 14, 15 and 17
Rotary Head Kit - Minor:
P/N 2100203
Includes items 9, 10, 15 and 17
Complete Rotary Head Kit:
P/N 2103220 (DCFSCP20GZ)
P/N 2103221 (DCFSCP20)
Includes all items
Photo of Rotary Head - Major as assembled.
ITEM
NO.
5
10
11
12
13
8
9
6
7
14
15
16
17
18
1
2
3
4
PART
NO.
2500010
2500011
2520030
2520028
2520027
2640004
2640015
2701012
2701011
2701010
2720007
2530008
2530007
2520029
2710000
2520113
2200092
2200050
2500012
2640012
DESCRIPTION
HOUSING (DCFSCP20GZ)
HOUSING (DCFSCP20)
RETAINER, BEARING
RETAINER, BEARING
SPACER, BEARING
BEARING (DCFSCP20GZ)
BEARING (DCFSCP20)
O-RING
O-RING
O-RING
SPRING
PIN
STEM, SMALL
SNAP RING
BACK UP RING
STEM
SCREW, M5 X 16
WASHER
RETAINER, BEARING
ZERK, GREASE (DCFSCP20GZ)
Ref 300843 Rev. C
08-13
QTY.
2
3
1
2
1
1
1
1
1
3
1
1
3
1
1
1
1
2
PROFESSIONAL FLAT SURFACE CLEANER
FROM GENERAL PUMP
• COMPENSATING GUN FEATURE
• FULL 20” CLEANING PATH
• HEAVY-DUTY ANODIZED
ALUMINUM COMPONENTS
• RUGGED ABS COVER DCFSCP20
DCFSCP20GZ
OPERATOR’S MANUAL
General Pump is a member of the
Interpump Group
Ref 300843 Rev.C
08-13
8
WARNING: Read Before Operating Machine
Always wear protective eyewear
Keep clear of rotating nozzles
Never lock trigger gun open with any device
Drain water in cold weather to avoid freezing
Tampering with any part of this machine will void all warranties
Operating Instructions
1. Connect to Pressure Washer.
2. Turn water on and open valve. Open trigger gun for flow of water through nozzles. Nozzles must have flowing spray. If not, remove tips and clean; reassemble, making sure that groove of nozzle is parallel to spray bar. Use thread sealant when installing nozzles.
3. Start Pressure Washer. The Hammerhead is ready for operation.
4. Walk slowly behind the Hammerhead cleaning as you go. If striping occurs, slow down your pace.
5. Periodically check weep hole on bottom of swivel. Water will seep slowly; if water shoots out, stop and replace seals. Swivel assembly can be rebuilt.
6. For maximum effectiveness keep spray tips clean. If the machine vibrates, stop and clean spray tips.
7. Grease the swivel with one or two grease gun pumps every 200 hours (or once about every 30 days of use).
DO NOT ALLOW MACHINE TO REMAIN STATIONARY
ON SOFT SURFACES SUCH AS WOOD.
Caution: Striking any raised obstacle during operation will damage machine. If contact does occur and results in vibration when operating machine, STOP and replace spray bar. Continued operation could result in serious injury or damage to machine.
Operating Pressures: 1,000 to 4,000 PSI
Max Flow: 8.0 GPM
Dimensions: 70” x 21” x 21”
Weight: 21 lbs.
General Pump
1174 Northland Drive • Mendota Heights, MN 55120
Phone: 651.686.2199 • Fax: 800.535.1745
www.generalpump.com • [email protected]
Ref 300843 Rev. C
08-13
ITEM
NO.
PART
NO.
DESCRIPTION QTY.
8
9
6
7
4
5
2
3
1
2103220 Swivel (DCFSCP20GZ)
2103221 Swivel (DCFSCP20)
2660045 Deck, GP, 20”
2530009 Arm, Rotary, Assy., 20”
2630010 Plate, Retaining
2540023 Collar, Split
2200055 SHCS, M8
2200054 SHCS, M8
2540020 Block, Handle
2200047 Bolt, M6
10 2203406 Washer, M6
11 2540021 Handle, Lower
12 2540022 Handle, Upper
1
2
8
4
1
1
1
1
1
8
1
1
ITEM
NO.
PART
NO.
DESCRIPTION QTY.
13 2660047 Grip, Handle
14 2660046 Plug, Handle
15 2660059 Brush Assy., 20” 1
16 DCG4000FSC Gun, Flat Surface Cleaner 1
1
1
17 2200053 Nut, M8 x 1.25
18 D10009 Plug
19 D10004 Coupler, 3/8 x 3/8-M
20 2200026 Nut, M6, Nylok
21 2202010 Pin, 55mm, w/Ring, SST
22 2200058 HHCS
23 2200018 Washer, M6
24 2203507 Washer
25 2702000 Hose, FSC, 20”
4
1
2
2
1
1
2
4
1
Ref 300843 Rev. C
08-13
