®

PRINCETON

Spread Lavatory Faucet with

Speed Connect

®

Drain

Installation

Instructions

4508.801

Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on

American Standard faucets.

Speed Connect

®

Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

Certified to comply with ANSI A112.18.1

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Recommended tools

Channel Locks Adjustable Wrench Tubing Cutter Flat Blade Screwdriver

1

INSTALL SPOUT

Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.

Assemble RUBBER WASHER (4) , BRASS WASHER (5) and LOCKNUT (6) onto

SPOUT SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) firmly. Fig. A.

Fig.

A.

1

2

3

1A

INSTALL VALVE BODY

CAUTION

Turn off water at main supply.

Place RUBBER RING (9) into SCUTCHEON (10) .

Install LOCKNUT (11) onto VALVE BODY (8) .

From under side of mounting surface, install VALVE BODY (8) through valve mounting holes. Threads of VALVE BODY (8) should extent at least 5/16 of a inch above mounting surface top. Fig. B.

Thread ESCUTCHEON (10) onto VALVE BODY (8) until snug against internal stop. If necessary, adjust

LOCKNUT (11) .

Hand tighten LOCKNUT (11) to secure VALVE BODY (8) .

Repeat above steps for opposite VALVE BODY (8A) .

SLOT

1

MOUNTING

SURFACE

10

9

5/16'' MIN.

10

9

8A

Fig.

B.

11

8

8

11

7

4

5

6

12

M968832 Rev.1.8 (5/18)

1

2

POP-UP DRAIN

Remove CLEAR PLASTIC COVER (1) .

Remove CARDBOARD SPACER (2) from under

DRAIN POP-UP (3) .

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig.

B.

Fig.

A .

1

3

2

3

REMOVE FLANGE

Thread FLANGE (1) counter-clockwise and remove

FLANGE (1) and FOAM GASKET (2) from drain body. Fig.

A.

Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against

LOCKNUT (3). Fig.

B.

Fig.

A .

1

2

4

3

F i g .

B.

F i g .

B.

DRAIN

BODY

4

4 INSTALL DRAIN FROM

BELOW FIXTURE

From under side of SINK install DRAIN BODY (1) up through drain outlet.

Note: No plumber’s putty or caulk is required.

The CABLE ATTACHMENT

POINT (2) must face towards the rear of the SINK.

Install FOAM GASKET (3) and

FLANGE (4) onto drain body from above SINK and tighten

FLANGE (4) firmly.

4

3

REAR OF SINK

DRAIN

OUTLET

1

2

6

FLANGE GASKET AND POP-UP KNOB

Check DRAIN FLANGE in SINK to ensure that

WHITE FOAM GASKET (3) is fully compressed and not visible. Fig.

A.

POP-UP KNOB (1) must be fully down. Fig.

B.

Fig.

A.

WHITE FOAM

GASKET

NOT VISIBLE

5

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) firmly with Adjustable

Wrench or Channel Locks.

DRAIN

FLANGE

Fig.

B.

DOWN

1

1

M968832 Rev.1.8 (5/18)

2

7

ATTACH CABLE CONNECTOR

Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig.

A.

Your new POP-UP DRAIN installation is now complete. Fig.

B.

Note: Tailpeice on pop-up drain is 1-1/4” O.D.

Fig.

B.

Fig.

A.

1

Fig.

B.

2

1-1/4” O.D.

8

CHECK OPERATION OF POP-UP

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.

1

2

9

MAKE WATER SUPPLY AND WASTE CONNECTIONS

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED

AND MUST BE PURCHASED SEPARATELY.

Thread TEE BODY (4) to SPOUT SHANK (5) .

Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A) .

Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE

SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3) . Use adjustable wrench to tighten connections. Do not over tighten.

Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.

Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet.

1

1/2" PIPE THREAD

7

6

5

2

FLEXIBLE

SUPPLIES

4

3/8 O.D.

BULL-NOSE

RISERS

COLD

6A

7A

1A

COUPLING

NUT

3

COMPRESSION

NUT

FERRULE

HOT

3/8 COMPRESSION

CONNECTION

M968832 Rev.1.8 (5/18)

3

10

INSTALL HANDLES

Push ADAPTER (1) on VALVE STEM (2) , so that the hole of the

ADAPTER (1) without a spline is facing up. See figure "A" . Tighten

STEM SCREW (3) to secure ADAPTER (1) .

Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4) .

Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) until snug against mounting surface .

Figure "A"

4

TOP

THREAD ON

TO DECK

ADAPTER

1

3

2

5 SPLINE END DOWN

11

TEST INSTALLED FITTING

With HANDLES (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3) .

Operate both HANDLES (1) to flush water lines thoroughly.

Replace AERATOR (3) .

1

12

CHECK DRAIN CONNECTIONS

Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.

Release POP-UP KNOB (5) down and check all drain connections and "P" trap for leaks. Tighten if necessary.

WASTE

OUTLET

4

5

1

3

COLD

2

13

CARE INSTRUCTIONS:

DO: CLEAN WITH CLEAR WATER.

DRY WITH A SOFT COTTON

FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE

PRODUCT WITH SOAPS, ACID,

POLISH, ABRASIVES, HARSH

CLEANERS, OR A CLOTH WITH

A COARSE SURFACE.

“P” TRAP

2

HOT

14

SERVICE

HANDLE

ASSEMBLY

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position. Unthread HANDLE

BASE (1) from DECK ADAPTER (2) .

Pull HANDLE ASSEMBLY off VALVE STEM (3) .

Remove SPRING CLIP (4) . Lift STOP WASHER (5) , turn 90˚ and replace. Replace SPRING CLIP (4) .

UNTHREAD

Find correct position of HANDLE ASSEMBLY by adjusting male teeth on VALVE STEM (3) to female teeth in HANDLE.

Thread HANDLE ASSEMBLY onto DECK ADAPTER (2) until snug against mounting surface.

4

1

90˚

If spout drips, operate handles several times from

OFF to ON position. Do not force - handles turn only 90˚ .

2

3

5

M968832 Rev.1.8 (5/18)

Speed Connect

®

Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode .

CABLE ADJUSTMENT PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig.

A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as

“Cam” in the illustration. Fig.

B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will

Stopper should be in the UP position. Fig.

B, C.

Push DOWN on the Lift-Knob to make sure it is fully down. Fig.

C.

go. At this point the

Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the

Drain Body Connection (2) and hand-tighten. Fig.

A.

Fig.

A.

Fig.

B.

Fig.

C.

DOWN

CAM

1

RE-ATTACH

1

CAM CAP

STOPPER

DISCONNECT

2

STOPPER REMOVAL PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig.

A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig.

B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig.

E.

Fig.

D.

The Stopper can now be removed by lifting it out of the Drain. Fig.

F.

Fig.

D.

Fig.

E.

REMOVE

CAM

Fig.

F.

REMOVE

CAM CAP

M968832 Rev.1.8 (5/18)

5

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig.

G.

To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the

Sink and the American Standard logo is facing front . Rotate

Stopper slightly if necessary so that the Stopper slides all the way down.

Fig.

G.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig.

J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig.

K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be in “Locked” mode and not be removable.

LOGO

LOOP TOWARD

REAR OF SINK

DRAIN

Locked Mode

(Vandal Proof)

Fig.

G.

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig.

H.

To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the

Sink and the American Standard logo is facing rear . Rotate Stopper slightly if necessary so that the Stopper slides all the way down.

Fig.

H.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig.

J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig.

K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be in “Unlocked” mode and removable .

LOGO

180˚

LOOP TOWARD

FRONT OF SINK

DRAIN

Unlocked Mode

Fig.

H.

Fig.

J.

INSTALL CAM

CAM

Fig.

K.

INSTALL

CAM CAP

M968832 Rev.1.8 (5/18)

6

M964966-YYY0A

LIFT ROD AND KNOB

M962248-0070A

DECK ADAPTER KIT

918555-0070A

HANDLE SCREW

918049-0070A

ADAPTER

994053-0070A

CARTRIDGE

M906617-0070A

ATTACHMENT NUT

M953006-0070A

TEE & HOSE KIT

PRINCETON

®

Spread Lavatory Faucet with Pop-up Drain

MODEL NUMBER

4508.801

M907559-YYY0A

SPOUT ESCUTCHEON

M964481-YYY0A

AERATOR (1.2 GPM)

A911914-0070A

SEAL

M961733-0070A

SPOUT MTG. KIT

Replace the "YYY" with appropriate finish code

CHROME

SATIN NICKEL

OIL RUBBED BRONZE

002

295

224

M962404-YYY0A

HANDLE KIT

M952425-YYY0A

DRAIN ASSEMBLY

M919660-0020A

6” TAILPIECE

(NOT INCLUDED

WITH FAUCET)

M962544-YYY0A

STOPPER

ASSEMBLY

M952435-0070A

CABLE ASSEMBLY

M962457-YYY0A

FLANGE

ASSEMBLY

M922872-0070A

CAM SEAT INSERT

M962552-0070A

CAM ASSEMBLY

M913207-0070A

TAILPIECE INSERT

A919661-0020A

TAILPIECE

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST

Saturday 10:00 a.m. to 4:00 p.m. EST

IN CANADA 1-800-387-0369

(TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-1200

Product names listed herein are trademarks of AS America, Inc.

© AS America, Inc. 2018

7

M968832 Rev.1.8 (5/18)