NETGEAR RND2110 Network Card Setup Manual 32 Pages
advertisement
ReadyNAS Duo Setup
Manual
NETGEAR , Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
February 2008
208-10215-01 v1.0
© 2008 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR, the NETGEAR logo, ReadyNAS, X-RAID, FrontView, RAIDar, RAIDiator, Network Storage Processor, and NSP are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Copyright Information
It is forbidden by law to view, copy, broadcast, use, show or share copyrighted material without the express permission of the copyright owner. You are solely responsible to obtain the appropriate permission or license necessary for any copyrighted materials accessed or used with this device.
Hard Drive Disclaimer
Adding or using your own hard drive(s) is an option with this NETGEAR product. Please refer to the NETGEAR
ReadyNAS hard drive compatibility list for qualified drives when selecting and installing your own hard drive(s). This
NETGEAR product is not data redundant with a single disk drive. By using this NETGEAR product, you understand and agree that (i) NETGEAR does not warrant any disk drive not provided or installed by NETGEAR; and (ii) NETGEAR is not responsible and you hereby release NETGEAR from any liability under any circumstances whatsoever for any damage to, loss of data or loss of contents of any hard drive use with this NETGEAR product, regardless of whether such hard drive is provided by NETGEAR or qualified to be compatible with this product. In no event will NETGEAR’s liability with respect to a failed disk drive or failed product exceed the cost of a replacement disk drive or replacement product, as applicable. In certain circumstances data loss may be permanent and unrecoverable and therefore you are highly encouraged to separately maintain a backup copy of any data that you store on the hard drive(s) used with this
NETGEAR product.
ii
Contents
ReadyNAS Duo Setup Manual
iii
iv
Preparing Your ReadyNAS Duo
This Setup Manual provides instructions for connecting the ReadyNAS Duo to your network
( “Installing RAIDar on Windows” and
Accessing Your ReadyNAS Device” on page 2 and
“Using the Setup Wizard” on page 11
).
Before installing the RAIDar Utility, please note that:
• RAIDar and RAIDar Widget for Mac are utilities used for discovering the ReadyNAS device on your network. They are located on the ReadyNAS Resource CD . The RAIDar utilities are useful in environments where the ReadyNAS Duo obtains a random DHCP IP address.
• RAIDar runs on Microsoft Windows and Linux and takes up approximately 40MB of disk space after installation. The RAIDar Widget for Mac runs on Mac OS X and takes up approximately 500 K of space.
• Your client system must reside on the same IP address subnet.
It is forbidden by law to view, copy, broadcast, use, show or share copyrighted material without the express permission of the copyright owner. You are solely responsible to obtain the appropriate permission or license necessary for any copyrighted materials accessed or used with this device.
Installing RAIDar on Windows
Load the Resource CD.
Follow the installation wizard to install RAIDar for Microsoft Windows.
(If the Autorun installation utility does not start automatically, double-click Autorun.exe
to start the installation.)
Installing RAIDar on Linux
Log in as root. Load the Resource CD, open the Linux RAIDar setup folder, and double-click on
Setup_Linux.sh
to start the installation.
1
If you have problems running RAIDar under Linux:
• To discover the IP address of ReadyNAS, open a terminal session and type nmblookup -R
VOLUME.
If you have a ReadyNAS with an LCD (such as the ReadyNAS NV+), press the power button once to display the IP address.
• To connect to the FrontView Setup Wizard, open a browser, and use the returned IP address to enter http://<ipaddr>/admin . Then, go to Step 2 in
.
• If you already have an existing workgroup or domain in your environment, ReadyNAS will try to locate that name. If VOLUME does not work, try using the workgroup/domain name used on your network in the nmblookup command.
Installing the RAIDar Widget on Mac OS X
To install the RAIDar Widget on the Mac Dashboard:
1.
Load the Resource CD . Scan the CD contents to locate the Mac folder. When you open the
Mac folder, double-click on the RAIDar1.0.wdgt.zip
to start the installation.
Figure 1
2.
3.
Follow the screen prompts, Do you want to Install Widget “RAIDar” and open it in
Dashboard , and click Install.
When installation is complete, the RAIDar Widget image will display. Click Keep to confirm installation of the widget on the Dashboard.
2
Detecting and Accessing Your ReadyNAS Device
There are several methods for detecting your ReadyNAS Duo device. You can use the RAIDar utility, or you can detect your ReadyNAS Duo by accessing your router and pasting the
ReadyNAS Duo IP Address into your browser.
Using the RAIDar Utility on Windows and Linux
Before using the RAIDar utility to detect your device, power on ReadyNAS and wait for it to boot up (approximately 2 minutes).
Preparing Your ReadyNAS Duo
To detect your ReadyNAS Duo device using RAIDar:
1.
Open RAIDar by clicking the RAIDar icon on your desktop. The RAIDar utility will scan your network to locate all connected ReadyNAS devices.
Figure 2
Your ReadyNAS Duo device will be detected when the device has successfully booted and has started a network connection. If you have multiple ReadyNAS devices on your network, match the MAC Address of the system to the address listed on the back of your ReadyNAS
Duo device.
2.
Figure 3
Select the device and click Browse to access the default shares called backup and media . The backup share can be used as a repository for your data and to backup your data.
Preparing Your ReadyNAS Duo 3
Figure 4
Using the RAIDar Widget on the Mac OS X
Before using the RAIDar Widget utility to detect your device, power on ReadyNAS and wait for it to boot up (approximately 2 minutes).
To detect your ReadyNAS Duo device using the Mac RAIDar Widget:
1.
Press F12 on your keyboard. The Mac Widget Dashboard will display.
Figure 5
2.
As you view the Widget Dashboard, roll over the different elements on the Dashboard to display statistics. For example, if you roll over the drive bays, statistics will display for that drive.
Click the ReadyNAS Duo image.Your ReadyNAS Duo device will be detected when the device has successfully booted and has started a network connection. If you have multiple
4 Preparing Your ReadyNAS Duo
ReadyNAS devices on your network, match the MAC Address of the system to the address listed on the back of your ReadyNAS Duo device.
Figure 6
3.
Select the ReadyNAS Duo device and click AFP Access to access the default shares called backup and media . The Connect to Server screen displays. Select the Guest radio box and click Connect.
4.
Figure 7
The Volume workgroup displays containing the backup and media share folders.The backup share can be used as a repository for your data and to backup your data. The media share contains three additional folders for your Music, Pictures and Video.
Preparing Your ReadyNAS Duo 5
Figure 8
Using the ReadyNAS Duo IP Address
1.
2.
When your ReadyNAS Duo is connected to your network through your router, your router stores, and can display, the IP address of the ReadyNAS Duo. (Your router will also display the IP addresses of all other devices connected to it.)
To access the IP address of your ReadyNAS Duo:
Open a browser window using Explorer, Firefox or Safari:
In your browser address field, enter the IP address of your router. In this example, the default
IP address for the router is shown below.
Figure 9
3.
Browse through your router menu and locate the screen that shows your router’s attached devices. You should see a screen similar to the one below.
6
Figure 10
Preparing Your ReadyNAS Duo
4.
Copy the IP address of the ReadyNAS Duo and enter it into your browser address field and append it with /admin , as shown below.
Figure 11
5.
Click Enter. The ReadyNAS Duo login window displays. You will be prompted for your User
Name and Password. The default user name is admin and the password is netgear1 .
Figure 12
See the “Using the Setup Wizard” on page 11
to continue configuration of the ReadyNAS
Duo Setup Wizard.
Copying Files From Your PC to Your ReadyNAS Duo
The easiest and most reliable method to access your share folders is to use the RAIDar utility (see
“Using the RAIDar Utility on Windows and Linux” on page 2
). When RAIDar is installed, you need only open the RAIDar utility by clicking the icon on your desktop (Windows) or by pressing
F5 to open the Dashboard (Mac OS X). Once RAIDar is open, select your NAS device and click
Browse (Windows) or AFP Access (Mac OS X). Your share folders will display, similar to the
screen shown in Figure 4 on page 4 (Windows) or
Figure 8 on page 6 (Mac OS X).
The folder structure in the ReadyNAS Duo includes a Backup folder, a Media folder containing three sub-folders (Music, Pictures and Videos), and a Printer/Fax folder (Windows only).
Preparing Your ReadyNAS Duo 7
To verify that you can copy files to and from your new ReadyNAS Duo drive:
1.
Open the RAIDar utility. Select the ReadyNAS Duo and click Browse (Windows) or AFS
Access (Mac OS X) . The ReadyNAS Duo share folders display. (No password is required.)
2.
From your computer, select a file and either drag it to one of the folders on the ReadyNAS
Duo drive or right-click (Windows) or control-click (Mac OS X).
3.
Choose Copy from the context menu and then Paste the file into one of the folders.
As an option, on simple networks, you can also browse your network neighborhood to access your
Share folders. Your ReadyNAS Duo is identified by “nas-” plus the last 6 digits of its unique MAC address—which is the same name as the Host name. The MAC address of your ReadyNAS Duo is printed on the label on the bottom of the unit.
To access your Share folders on Windows OS:
1.
2.
Select Start > Explore.
Scroll down to “My Network Places”. Click My Network Places > Entire Network >
Microsoft Windows Network. The Volume workgroup displays. (Volume is the default workgroup name.)
3.
Open the Volume network to access your share folders.
To access your Share folders on Windows Vista:
1.
2.
Select Start > Explore.
Scroll down to “Network” and click Network. The Network workgroup will open and display all of the items on your network.
3.
Select the ReadyNAS Duo to access your share folders The ReadyNAS Duo is identified by
“NAS-” plus the last six digits of its MAC address.
On Windows Vista, the ReadyNAS Duo icon also displays when Network is selected. You can then access the ReadyNAS Duo Setup Screen (Advanced
Features and Setup Wizard) without using RAIDar.
To access you Share folders on Mac OS X:
1.
Select Finder Go > Network.
2.
3.
Select the My Network folder to display the ReadyNAS Duo host name.
Click the icon for the ReadyNAS Duo you want to access. When the Connect to Server screen displays, select the Guest radio box and click OK. Your share folders will display.
8 Preparing Your ReadyNAS Duo
See the ReadyNAS Duo User Guide for more specifics on using this method to access your share folders for Microsoft Windows and for the Mac OS X.
Preparing Your ReadyNAS Duo 9
10 Preparing Your ReadyNAS Duo
Using the Setup Wizard
Most options in the Setup Wizard are pre-selected to fit most typical environments. It is highly recommended that you go through the wizard if this is your first ReadyNAS Duo installation. For information on using the Advanced Control mode, see the ReadyNAS User Guide (a link to the online manual, is on your Resource CD).
In a typical Setup Wizard process, you will set the clock, set up alert notification contacts, configure networking, change the default administrator password, and create shares.
To connect to the Setup Wizard:
1.
2.
Click Setup in RAIDar (or paste the ReadyNAS Duo IP address in your browser window). If the Security Alert screen displays, click Continue to this website or OK.
The login screen displays. You will be prompted to enter your User Name and Password. The default user name is admin and the password is netgear1 .
Figure 13
3.
Click OK. The ReadyNAS Setup Wizard screen displays.
11
Figure 14
As you traverse through the setup screens, you will notice the command bar in the upper right corner and the navigation and status bar at the bottom.
The command bar typically provides options to refresh the browser window, display help (if available), and log out, as shown below.
Figure 15
Use the navigation bar to browse through the wizard. Be aware of the following conventions:
• Click Next to accept any changes made in the current window and to apply these changes.
• If a screen has an Apply button, click Apply to save your changes before clicking Next . If a screen has multiple tabs, clicking Next will allow you to browse through the tabs before continuing to the next menu screen.
12
Figure 16
Using the Setup Wizard
• If you wish to log out of FrontView at any time, click Logout . (You must close your browser window to securely log out.)
• The status bar right below the navigation bar provides the status of individual devices in the
ReadyNAS.
– The green LED indicates that everything is working normally.
– The amber LED indicates a warning or a failure condition. (See the ReadyNAS Duo User
Guide for information on other LED behavior. A link to the ReadyNAS Duo User Guide is on the Resource CD ).
• The menu bar on the left provides the option to switch between Setup Wizard and Advanced
Control modes. More menus are available once you enter the Advanced Control Mode.
Figure 17
Setting the Clock
To set your ReadyNAS clock:
1.
From the Welcome screen, click and time zone. The clock must be set appropriately to ensure that files maintain their proper timestamp.
Next. The Clock screen displays. You can set the date, time,
Using the Setup Wizard 13
3.
4.
2.
Figure 18
The ReadyNAS Duo will automatically attempt to synchronize with a public NTP server when it first boots up. If you want to synchronize the ReadyNAS Duo with a specified local or external NTP server, select the Synchronize clock with… radio box in the NTP Option section. Then, specify the NTP servers in the fields provided.
Click Apply to save your settings.
Click Next to set up the Alert contacts.
Configuring Alert Contacts
On the Alerts screen, you can enter your contact name(s) where you want alert messages sent. To enter your Alert contact names:
1.
Enter one or more email address that you wish to use as the system alert contact.
Email alerts are the most effective way for the ReadyNAS Duo to notify you of system status, various warnings, and fatal system errors.
14 Using the Setup Wizard
2.
Figure 19
Click Send Test Message to verify that alert messaging is working. If you do not receive the test message, check the network gateway and DNS settings.
Some network firewalls prevent unknown message transfer agents (MTAs) (such as those used by the ReadyNAS Duo) from working. If this is the case, you will need to specify a remote
SMTP server in Advanced Control mode when you are done with the Setup Wizard. This method is covered in the ReadyNAS Duo User Guide .
Various email services may filter out the test message and actual email alerts sent by the ReadyNAS Duo. Verify that the test message arrives at the email destination before continuing.
3.
Click Next to access the Ethernet Network screen.
Using the Setup Wizard 15
Configuring Your Network
Ethernet Settings
To configure your Ethernet settings:
1.
You can accept the default Ethernet settings if the ReadyNAS Duo is installed in a network environment where DHCP service is used. Otherwise, specify a static address.
If you assign static IP addresses, be aware that the browser will lose connection to the
ReadyNAS Duo device after the IP address has been changed. If you encounter this problem, click Rescan in RAIDar to rediscover the device and reconnect from there.
Figure 20
2.
Click Next to access the Global Settings screen.
Global Settings
The Global Settings screen allows you to specify the ReadyNAS Duo host name, default gateway and DNS servers.
To set the Global Settings:
1.
Enter a hostname that you wish to advertise the ReadyNAS Duo on your network. This hostname can be used in place of the IP address when accessing the ReadyNAS Duo from
Windows, or over OS X using SMB. This is also the name that will appear in the RAIDar scan list.
16 Using the Setup Wizard
.
2.
If you selected the DHCP option in the Ethernet tab, the gateway and domain name server fields will automatically be filled based on the settings from your DHCP server. If you selected the Static option, manually enter the information in the field provided
Figure 21
3.
Click Apply to save any changes. Then, click Next to configure the ReadyNAS Duo Security.
Setting Up Your Password
The Admin Password screen allows you to change the default password assigned for the admin user. You must change the password before continuing.
To change your password:
1.
Enter a new admin password in the field provided; then reenter the password to confirm your selection.
Using the Setup Wizard 17
2.
3.
Figure 22
Specify a password recovery question and the expected answer, along with your email address in the remaining fields. This information will allow you to reset the password on the
ReadyNAS Duo in case the password is lost. See the ReadyNAS Duo User Guide for details on this process, if required.
Click Apply. Click Next to display the Standard File Protocols screen.
Adding User Accounts
In order for ReadyNAS Duo users to access the share folders, security on the ReadyNAS Duo requires that you set up a user account for each user.
To set up a user account:
1.
Enter a name for the account (a user friendly, recognizable name).
2.
3.
Enter the users email address (this is optional) so that the user is informed of any account changes.
Enter data in the remaining fields (optional). However, it is recommended that you enter a password for each account.
4.
Click Apply for you settings to take affect.
In the sample below, we entered two user accounts: Paul and Smithy. You can review and change any data for user accounts by selecting the All tab or by selecting the letter tab that corresponds to the first letter of the user’s name.
18 Using the Setup Wizard
Figure 23
Setting Up File Sharing Services
Standard File Protocols
A share is simply a network folder on the ReadyNAS Duo that clients communicating in various file access protocols from different operating systems can access. To select your file protocols:
1.
First, on the Standard File Protocols screen, select the file protocols you wish to enable:
• CIFS for Windows clients (Macs running OS X can support this as well).
• NFS for Unix/Linux.
• AFP for Macs.
• FTP
• HTTP/S for browser access.
CIFS, AFP and HTTP are configured by default.
More details on these services are described in the ReadyNAS Duo User Guide . You can elect to keep the defaults and revisit this page to fine-tune your services at a later time.
Using the Setup Wizard 19
Figure 24
2.
If you made changes, click Apply. Then click Next to set up Streaming Services .
Streaming Services
The ReadyNAS Duo comes with a complete list of streaming media services, allowing you to use a network media player to stream media files directly from the ReadyNAS Duo without going through a PC. By default, no Streaming Services are selected.
20 Using the Setup Wizard
To select your Streaming Services:
1.
Select the radio box for the desired service.
Figure 25
2.
Click Apply to save your settings. Then, click Next to set up Shares .
Configuring Installed Add-Ons
Two add-ons are available with the ReadyNAS Duo—Bit Torrent and ReadyNAS Photos. Both are disabled by default.
• Bit Torrent. The ReadyNAS Duo enables peer-to-peer file sharing and allows the ReadyNAS
Duo to queue and index torrent download files. For information on enabling and using the
BitTorrent download capability, see the ReadyNAS Duo User Guide . A link to the User Guide is on the Resource CD.
Using the Setup Wizard 21
• ReadyNAS Photos. The ReadyNAS Duo allows you to share photos with select users on the
Internet. You must install ReadyNAS Photos software which is available on the ReadyNAS site. Simply click Install ReadyNAS Photos and follow the on-screen prompts. Once you have enabled this feature and downloaded the software, you will be able to share photos located in your Pictures folder. (For more information about installing or using ReadyNAS
Photos, see the ReadyNAS Duo User Guide . A link to the User Guide is on the Resource CD.
)
Figure 26
Setting up Shares (or Folders)
Share List
The Share List screen lists the share folders currently available on the ReadyNAS Duo. As an example, in the Shares on RAID Volumes section, two shares, backup and media , have been preconfigured for default access.
22 Using the Setup Wizard
.
Figure 27
The Shares on the USB Storage Devices section displays the USB Storage shares—if USB storage device are attached.
You can limit share access to specific hosts by customizing access control. When you specify a host in the allow list, no other hosts will be able to access the share using the selected file protocol.
Hosts can be listed using their IP address or valid DNS name separated by commas
Different options are available depending on the security mode selected. For example, in User or
Domain security modes, you have the option of restricting share access based on user and group account. For more advanced share access options, see the ReadyNAS Duo User Guide .
To customize share access:
1.
Click the will display.
link adjacent to the share you want to access. A screen similar to the following
2.
3.
Select which options you want to change and then click Apply to save your settings.
Click Display Share List to return to the Share List screen.
Using the Setup Wizard 23
Figure 28
Adding Shares
You can add additional share folders to suit your needs such as downloads, software, scratch-pad, and so forth. In the following screen, we added an additional share folder, brochures . (The Share
Name folders are listed alphabetically.)
To add more shares:
1.
2.
On the Add Shares menu, enter a name for your share folder in the Name field. In this example, we added the share “Brochures”. You can enter up to five share names with share descriptions.
Allowing public access to this share is selected by default. To disable user authentication, deselect the Public Access checkbox.
24 Using the Setup Wizard
3.
4.
Figure 29
In the figure above, one share is being added, and Public Access has been disallowed.
Click Apply to save your changes.
Click Next to set up Printers.
Setting Up Printers
If you have not already done so, you can now connect your USB printers to the ReadyNAS Duo.
1.
After connecting your USB printers, wait a few seconds, then click
Printers list. The print share name will automatically reflect the manufacturer and model of your printer.
Refresh to view the USB
Using the Setup Wizard 25
2.
To assign a printer driver to a print share in Windows, click Browse in RAIDar, or simply enter \\hostname in the Explorer address bar, then double-click the printer icon.
Figure 30
3.
Click Apply to save your settings. Then, click Next to enter the final step in the Setup Wizard.
Registering Your Product
Register your ReadyNAS Duo product by clicking Register Product .Your ReadyNAS Duo product information will be placed in our warranty and support database so we can inform you of the latest software enhancements, bug fixes, and security alerts.
Figure 31
Click Next to continue with the Advanced Control mode. The Advance Control options are documented in the ReadyNAS Duo User Guide (a link to the ReadyNAS Duo User Guide is on your
Resource CD).
26 Using the Setup Wizard
Figure 32
You can now start accessing the shares that you just created using Windows Explorer. For instructions on how to access the shares from other client systems, see “Accessing Shares” in the
ReadyNAS Duo User Guide.
If you choose not to register at this time, you can always go to http://www.netgear.com/register , select your ReadyNAS product and register on-line. Then, enter your registration information on the form provided.
Using the Setup Wizard 27
28 Using the Setup Wizard
advertisement
Key Features
- Total installed storage capacity: 1 TB
- 0.25
- 35 W