EWheels Medical REMO AUTO-FLEX Instruction Booklet

PDF Download

Document

REMO AUTO-FLEX Instruction Booklet

01.INTRODUCTION

.........................................................................................1

02.IMPORTANT PRECAUTIONS ......................................................................2

2-1 BEFORE DRIVING SCOOTER

2-2 CAUTIONS WHEN DRIVING

2-3 CAUTIONS WHEN FOLDING / UNFOLDING SCOOTER

2-4 CAUTIONS WHEN DRIVING ON INCLINE

2-5 CAUTIONS WHEN CLIMBING

2-6 ELECTROMAGNETIC INTERFERENCE AND WARNINGS

2-7 SAFETY WARNING AND INSTRUCTION LABELS

03.IDENTIFICATION OF PARTS ......................................................................8

04.INTRODUCTION & OPERATION OF SCOOTER

4-1 IDENTIFICATION & OPERATION OF CONTROL PANEL

4-2 OPERATION OF MAIN SWITCH

4-3 OPERATION OF THROTTLE

4-4 OPERATION OF FREE-WHEELING (N-D LEVER)

4-5 TILLER HEIGHT ADJUSTMENT

4-6 SEAT ADJUSTMENT / DISMANTLE

.........................................9

05.FOLDING / UNFOLDING YOUR SCOOTER ..............................................13

06.BATTERY GAUGE & CHARGING THE BATTERIES

6-1 DISASSEMBLING BATTERY BOX

6-2 CAUTIONS FOR BATTERY & CHARGER

6-3 BATTERY GAUGE

6-4 OPERATING THE CHARGER

..................................15

07.CARE AND MAINTENANCE

7-1 INSPECTION CHECKS

......................................................................19

7-2 CLEANING AND MAINTENANCE 20

08.TROUBLE SHOOTING ..............................................................................22

09.OTHER INFORMATION

9-1 OPTIONS

.............................................................................24

10.TECHNICAL SPECIFICATIONS .................................................................25

REMO AUTO-FLEX Instruction Booklet

1.INTRODUCTION

Thank you and congratulations on purchasing your new Ewheels Medical mobility scooter.

It is designed to provide the transportation ability indoors and outdoors for person whose ability to walk is impaired, but who are still in terms of their eyesight and physically and mentally able to operate an electric scooter.

We pride ourselves on providing safe and comfortable products. Our goal is to ensure your complete satisfaction. We sincerely hope you enjoy your Ewheels Medical mobility scooter.

Please read and observe all warnings and instructions provided in owner’s manual before your operate the various functions of this scooter. Also, please retain this booklet for future reference.

If you have any questions, you can contact:

Ewheels Medical

6242E Greenway

Parkway #100

Scottsdale, Arizona

85254, U.S.A

or your local dealer:

REMO AUTO-FLEX Instruction Booklet

2.IMPORTANT PRECAUTIONS

2-1 BEFORE DRIVING SCOOTER

• Before take the first trip with mobility scooter, you should familiarize yourself well with the

operation of mobility scooter and with the operation elements. Please take your time

to read this introduction booklet.

• Before driving, please evaluate the personal condition, and fully understand the operation

of mobility scooter.

• Before charging the scooter, please release the Circuit Breaker on battery box first to

activate the system (see section 3)

• Scooter is shipped with 30% of battery charge only, batteries should be fully charged

before your journey for maximum performance and longevity (see section 6 ).

• Scooter is equipped with certain type of battery (lithium or optional lead-acid), if you want

to change it, please contact dealer to reset the battery system such as charging port

and controller setting. Only one type of batteries can be used on scooter, do not mix

the batteries and charge, or it may result dangers

• The maximum load of the scooter is 115KG. Do not exceed the maximum permissible

load. Exceeding the max.weight rating may result in injury to yourself.

• The mobility device is only designed for use by a single occupant whose maximum weight

does not exceed the maximum permissible load of the device. Never use the mobility

device to transport more than one person (including children).

• You should not assemble, maintain, and operate the mobility scooter before you read

this instruction booklet.

• Do not attempt to modify or dismantle the battery box or carry out any maintenance work

that is not described in this user manual.

• Do not change, modify, remove any parts (seat, shroud) from products especially safety

protected parts such as anti-tippers.

• Completely deflate the tires (air tires) before dismantling the rim or attempting.

• Materials and assemblies of scooter are flame resistant.

• Always keep battery box installed on scooter to avoid short-circuit, do not attempt to

remove battery box at all possible.

• Always keep the tiller screw knob fasten at whole time except when adjusting the tiller

height.

• Do not sit or stay on scooter when scooter is on moving transport vehicles to avoid

dangers

• Turn the power (key) off before getting on or off. (see section 4-2)

• Do not drive your scooter if you are under the influence of alcohol or medication that

may affect your ability.

• Do not turn off the power while driving. Doing so will bring the scooter to an abrupt stop

and danger.

• Please observe all relevant rules and regulations pertaining to pedestrians and road

users at all times when you are driving the scooter.

• Mobility device may only be used on the traffic routes for which it is approved in accordance

with the relevant national legislation.

• Always be aware of pedestrians and situations which might require extra care when

using your scooter on public walk ways and footpaths.

• Avoid driving scooter in dark or in conditions of bad weather and visibility for safety

• Do not turn the power on before you get in and sit securely on the seat.

REMO AUTO-FLEX Instruction Booklet

• Be certain that the power is turned off when get in, get out. This will eliminate

the possibility of accidentally activating the wigwag controls and causing injury.

• Keep your weight toward the middle of the deck. Putting most or all of your

weight on the edge of the deck may cause an unstable condition.

• Do not use hose pipe or splash water directly onto the scooter or store the

scooter in a humid condition such as rain or show as this may cause damage

to electronics.

• Do not remove safety protected parts such as anti-tipper from scooter.

• Do not use the unauthorized parts such as battery or charger on the scooter.

Use the accessories supplied from original dealer only.

• Do not exceed the maximum permissible load of scooter or it may cause

unbalance.

• Please stop operating the scooter and contact your dealer if you find the sign

of scooter malfunction.

• Please pay more attention when driving the scooter, the emergency stop may

encounter (ex. out of power, EMI interference)

• Keep the RF sensor key (Remote) carefully. Please contact dealer if the key

is lost.

Practice Tips ：

• If you are new to driving a scooter, it is a good idea to practice in a clear, safe space

on an flat level surface. (I.e. Park, Playground).

• Basic functions to practice ： Wig wag accelerate /Wig wag release /Stop /Reverse /Turn

/Ramp proceeding.

• Set the speed control to its lowest speed, slightly increase the speed when you are

getting familiar with the scooter.

• Practice operating your scooter in the presence of an attendant. Remember

that only with practice will you become a competent driver.

• Practice these basic functions until you feel that you have control of your scooter.

Accessories Contents for Your Scooter :

• Auto-folding version : control remote x 1 / RF sensor x 1

• Manual-folding version : key x 1 / spare key x 1

2-2 CAUTIONS WHEN DRIVING

• Please do the daily check before your journey always. (See section 7-1)

• Do not stretch your body out on the scooter.

• Do not use the mobile phone and wireless mobile devices while driving.

• Do not use the batteries of mobility scooter to charge any other electric devices, except

the accessories from original manufacturer.

• Do not drive on a slope which is over the limit. (See section 2-4)

• Please bypass, do not drive to across the obstacle over the limit (See section 2-5 )

• Do not attempt to drive the scooter under below hazardous road condition. If necessary,

please drive it in the presence of an attendant:

- Dark, bad weather such as in rain, snow, mist, storm, and poor visibility.

- Narrow paths, level crossing, and uneven terrain.

- Wet grass, sand, gravel, or any other potentially hazardous condition.

• Please stop operating the scooter if the batteries have drained, continuous operation

may damage the scooter.

• Do not drive when the seat lock is positioned in folding point (red). Scooter can be operated

only when the seat lock is in the fixation point (green). (see section 4-6)

REMO AUTO-FLEX Instruction Booklet

• When turning, reduce your speed and maintain a stable center of gravity. This greatly

reduces the possibility of a tip or fall.

• Do not bounce or jam on the footplate.

• Please always set the speed control to its lowest speed when you start to drive, and

observe all relevant rules and regulations pertaining to pedestrians and road users at

all times.

• Reduce speed when descending to prevent any danger. Increase speed when

ascending (see section 4-1)

• Do not turn off the power while driving.

• Do not operate on staircases or escalators.

• Do not attempt to climb curbs greater than limitation show on Technical Specification.

• Do not make S turns or sharp turns while driving. This may cause the scooter

to tip.

• Never place the scooter in freewheel mode (Neutral) when on any sort of an

incline or decline to avoid rollaway. .

• When the scooter is parked, the lever for engaging and disengaging the motors

must be locked firmly into the “DRIVE” position. (see section 4-4)

• Do not conduct any adjustment such as tiller / light setting / control panel setting

while driving.

• Do not pull the seat springs while driving to avoid dangers. (see section 4-6)

2-3 CAUTIONS WHEN FOLDING/UNFOLDING SCOOTER

• When folding or unfolding, you must place the scooter on a flat ground to avoid tip-over,

rollaway, or dangers. Never operating the folding/unfolding process on a slope

• Please read through the section 5 for folding / unfolding operation before you operate

the scooter.

• Turn off the power before you fold / unfold the scooter. (see section 4-2)

• Folding/unfolding actions will stop if any malfunctions are detected.( see section 8)

• Please make sure the lever for engaging and disengaging the motors must be locked

firmly into the “DRIVE” position before you fold / unfold the scooter. Never proceed the

folding/unfolding under freewheel mode “Neutral” position (see section 4-4)

• Scooter can be charged when it’s folded or unfolded. However, scooter will not respond

to folding / unfolding commands when charger is plugged. To operate the folding / unfolding,

please unplug the charger from the scooter (see section 6-4).

• Please remove all the accessories, such as armrests or bags out before folding / unfolding

the scooter

• Please observe environment surround you for safety before folding/unfolding the scooter.

• When the folding or unfolding is processing, please pay attention to the movement of

tiller for your safety.

• When the folding or unfolding is processing, do not sit or interrupt the process or it may

cause damage or danger to the scooter and yourself.

• Please double check and make sure the procedure of folding/unfolding is completed

before you get on the scooter.

• Do not turn on the power when the scooter is folded.

• Scooter can be rolled by front wheels and supporting

castors when it’s folded (refer to Right picture).

Supporting

Wheels

Front

Wheels

• Do not sit or stay on folded/unfolded scooter when scooter is on moving transport vehicles.

• Do not store the scooter in a humid condition such as rain or show as this may cause

damage to electronics. (see section 7-2 )

• The brake does not apply when the scooter is in folded and standing position. Do not

place the standing folded scooter on a slope to avoid roll-away and danger (Fig.1)

REMO AUTO-FLEX Instruction Booklet

• When folding or unfolding, you must place and lay down the scooter on a flat ground

(Fig. 2)

Figure 1 Figure 2

• Do not place scooter on a slope

when scooter is folded and standing.

• Place and laydown the scooter

before unfolding.

2-4 CAUTIONS WHEN DRIVING ON INCLINE

• The scooter has been rated to a maximum climbable height, obstacle height, and gap.

(see section 10)

• Never drive on a slope that exceeds the rated slope.

• For maximum stability, lean forward in your body while proceeding up ramps, inclines,

curbs, or any low rise. (please refer to following picture)

115kg / 6 degree

On flat road On slope

• The weight capacity limit at different ramp degree (please refer to above picture).

• Your scooter’s ability to travel up inclines is affected by your weight, your scooter’s speed,

your angle of approach to the incline, and your scooter setup.

• Please avoid to driving on a long ramp or any uneven terrain to prevent any danger from

motor defected.

• When driving down a ramp or uneven terrain, keep the scooter’s speed adjustment

set to the slowest to ensure a safely controlled driving.

• If the speed is too fast, release the throttle control lever, let the scooter stop.

When you feel that you again have control of your scooter, push the throttle

control lever forward and continue safely driving.

• To prevent any danger, do not make turns on ascending, descending ramp.

• The batteries voltage normally will go up when driving on descending road.

If the battery voltage becomes too high, the over-voltage protection will be

activated by slowing the speed till the scooter stops. (error light indicator will

flash 3 times). Please pull over the scooter to the safe area, release the wigwags

and restart the scooter again.

2-5 CAUTIONS WHEN CLIMBING

• The maximum height of obstacle and curb that scooter can

climb is up to 5 cm (A).

• The maximum gap that scooter can drive over is 10 cm (B).

• When driving scooter on ramp, adjust body center of gravity

for scooter stability (see section 2-4).

Even though your scooter has been rated with maximum climbable, we suggest not driving through an obstacle.

(A)

Figure 3 (B)

REMO AUTO-FLEX Instruction Booklet

2-6 ELECTROMAGNETIC INTERFERENCE AND WARNINGS

It is very important that you read this information regarding the possible effects of Electromagnetic Interference on your mobility scooter.

Mobility scooters may be susceptible to electromagnetic interference (EMI), which is interfering electromagnetic energy (EM) emitted from sources such a radio stations, TV stations, amateur radio (HAM) transmitters, two-way radios, and mobile phones. The interference

(from radio wave sources) can cause the mobility scooter to release its brakes, move by itself, or move in unintended directions. It can also permanently damage the mobility scooter control system. The intensity of the interfering EM energy can be measured in volts per meter (V/m). Each mobility scooter can resist EMI up to certain intensity. This is called its "immunity level." The higher the immunity level, the greater the protection. At this time, current technology is capable of achieving at least a 20 V/m immunity level, which would provide useful protection from the more common sources of radiated EMI. The immunity level of this mobility scooter model is not known.

There are a number of sources of relatively intense electromagnetic fields in the everyday environment. Some of these sources are obvious and easy to avoid. Others are not apparent and exposure is unavoidable. However, we believe that by following the warnings listed below, your risk to EMI will be minimized.

The sources of radiated EMI can be broadly classified into three types :

1.Hand-held portable transceivers (transmitters-receivers) with the antenna mounted

directly on the transmitting unit. Examples include: citizens band (CB) radios, "walkie

talkie," security, fire, and police transceivers, mobile phones, and other personal communication

devices.

Some mobile phones and similar devices transmit signals while they are ON, even when not being used

2.Medium-range mobile transceivers, such as those used in police cars, fire trucks, ambulances,

and taxis. These usually have the antenna mounted on the outside of the vehicle; and

3.Long-range transmitters and transceivers such as commercial broadcast transmitters

(radio and TV broadcast antenna towers) and amateur (HAM) radios.

Other types of hand-held devices, such as cordless phones, laptop computers,

AM/FM radios, TV sets, CD players, and cassette players, and small appliances, such as electric shavers and hair dryers, so far as we know, are not likely to cause

EMI problems to your mobility scooter.

Mobility Scooter Electromagnetic Interference ：

Because EM energy rapidly becomes more intense as one move closer to the transmitting antenna (source), the EM fields from hand-held radio wave sources (transceivers) are of special concern. It is possible to unintentionally bring high levels of EM energy very close to the motorized scooter control system while using these devices. This can affect mobility scooter movement and braking. Therefore, the warnings listed below are recommended to prevent possible interference with the control system of the mobility scooter.

Warnings ：

Electromagnetic interference (EMI) from sources such as radio and TV stations, amateur radio (HAM) transmitters, two-way radios, and mobile phones can affect mobility scooters.

REMO AUTO-FLEX Instruction Booklet

Following the warnings listed below should reduce the chance of unintended brake release or mobility scooter movement which could result in serious injury.

1.Do not operate hand-held transceivers (transmitters-receivers), such as citizens band

(CB) radios, or turn ON personal communication devices, such as mobile phones, while

the mobility scooter is turned ON;

2.Be aware of nearby transmitters, such as radio or TV stations, and try to avoid coming

close to them;

3.If unintended movement or brake release occurs, turn the mobility scooter OFF as soon

as it is safe;

4.Be aware that adding accessories or components, or modifying the mobility scooter, may

make it more susceptible to EMI; and

There is no easy way to evaluate their effect on the overall immunity of the mobility scooter.

5.Report all incidents of unintended movement or brake release to the distributor listed

on the inside front cover of this manual. Note whether there is a source of EMI nearby.

Important Information ：

1.20 volts per meter (V/m) is a generally achievable and useful immunity level against

EMI (as of May 1994). The higher the level, the greater the protection.

2.The immunity level of this product is at least 20/Vm.

2-7 SAFETY WARNING AND INSTRUCTION LABELS

1.Please read the instruction Booklet carefully before using your scooter.

2.Do not drive the scooter on slippery surfaces or on slopes over 6°~10°

3.Do not drive on highways, crowded roads, or unfamiliar areas.

4.Do not tum at high speed in either forward or reverse.

5.Do not wash with water or leave scooter in a humid Environment since

water can damage the electric parts.

6.Always re-engage the emergency freewheel drive after use.

7.Always switch off the scooter before dismounting or roating the seat.

Warning Sticker

1.Please read the instruction booklet carefully before using your scooter.

2.Do not drive the scooter on slippery surfaces or on slopes over 6~10 degrees limit.

3.Do not drive on highway, crowded roads, or unfamiliar areas.

4.Do not turn at high speed in either forward or reverse.

5.Do no wash with water or leave scooter in humid environment since water can

damage the electronic parts.

6.Always re-engage the emergency device after use

7.Always switch off the scooter before demounting or rotating the seat

Scooter information label

States the date of manufacture and serial number of the scooter. This product has been supplied from an environmentally aware manufacturer. It may contain substances that could be harmful to the environment. Recycling must be carried out in accordance with the respective national legal provisions.

3 European representative label

Wiring diagram for batteries

Instruction of battery lock nut (circuit breaker) label

Pinch point warning label

Keep hands away

CAUTION

Hot Surface.

Do not touch.

Seat position warning plate

Do not get on the scooter if the seat is not fixed. Push the seat forward until the seat locks to its position (green), you will hear a click sound.

Heat caution warning label

Be aware that the motor may normally become hot during operating. Please avoid skin contact.

Seat position indication label

Seat latch is locked when the seat positioned in green. Seat latch is released when the seat positioned in red. Do not sit if seat is positioned in red

Power warning label

N-D Lever Adjustment label

Instructs freewheel mode operation. (see section 4-4)

Charge port cap sticker

Fixation point reminder

Sit only when the seat slide is fixed to green point

REMO AUTO-FLEX

3. IDENTIFICATION OF PARTS

Instruction Booklet

Figure 4

9 12

No.

ITEM

Steering

Tiller Height Adjustment

Head Light

Front Wheels

No.

ITEM

Seat

Seat Backrest

Seat Knob

Battery Box

Footplate Cover

Seat Springs

Supporting Wheels

Rear Wheels

Battery Box Handle

Charging Port (battery box)

Circuit Breaker

Folding / unfolding light indicator / buttons

Charging Port (upper)

Control Panel / Power Switch

Throttle

Tail light / Brake light

N-D Lever

22 Anti-Tippers

*Above is only for reference, actual product may vary.

REMO AUTO-FLEX Instruction Booklet

4.INTRODUCTION & OPERATION OF SCOOTER

4-1 IDENTIFICATION & OPERATION OF CONTROL PANEL

1 2 3

5 6 7

Figure 5 - REMO AUTO-FLEX Control Panel

No.

ITEM

Speed Deceleration

Power Switch

Speed Acceleration

Digital Lock (number pad)

Head-light / Tail-light Switch

Battery Gauge / Error Light Indicator

Horn

Digital Lock (enter key)

FUNCTION

Press to decrease speed

Press to turn on / off the power

Press to increase speed

Set a password to lock the scooter

Press to turn on headlight and taillight.

Showing battery status or errors

Press to sound warning tone when necessary

Press Enter when password is confirmed

• Please keep the panel clean, away from water, oil, and dust as the RF reading range

may be reduced or malfunction may result.

• When operating the panel, always press on the center of the button to ensure the

button press is detected.

• Do not place any objects on the panel or it may disrupt the touch screen or cause

damage to the scooter.

• Battery / Error Indicator will be flashing if there is error, please stop operating the

scooter if indicator is flashing (see section 8).

Power Switch ：

• Press the button to turn on/off the power

• Power standby (locked) - Red light

• Power on (unlocked) - Green light

• Power off - Light off

Auto-power off :

Power will automatically be off in 30 seconds if no activity is detected during power standby

(locked, red light) period to prevent tap error.

Figure 6

REMO AUTO-FLEX Instruction Booklet

Digital Unlock Your Scooter ：

• Press the power switch, the power (red light) will be

on standby for you to unlock.

• To unlock, enter your password on the number pad (D),

light indicator (C) will light up each time when the number

is entered. Press (E) on the pad when password entering

is finished. (Figure 7)

• The power light will turn green when the scooter is

successfully unlocked.

Figure 7

(C)

(D)

(E)

Factory Default Password : 1234

If there is enter error, press the (E) key or power switch button again to re-enter the password.

Password Setting ：

• Once scooter is unlocked (power green light on), press and hold the (E) key for 3 seconds,

the pad light will be flashing three times.

• Enter your password on number pad (D), the password can be 1-4 digits number, digits

can be repeated. Light indicator (C) will light up each time when the number is entered.

• Press (E) on the pad when password entering is finished, pad light will be flashing three

times.

If there is enter error, press power switch button again or wait for 30 seconds to re-enter the password. Scooter must be unlocked before reset the password. If you forget the password, please unlock the scooter by RF sensor key.

RF Sensor Unlock Your Scooter ：

• Press the power switch, the power (red light) will be

on and standby for you to unlock.

• To unlock, place the RF sensor tag to the panel (spot

near power switch for best reading result) ( Figure 8)

• The power light will turn green when the scooter is

successfully unlocked.

• The sensor transmit is up to 20mm, however,

please keep the distance between RF sensor

Figure 8

and panel as close as possible.

• Do not dissemble the RF remote, the inner sensor chip may be damaged.

• Do not turn off the power while unlocking the scooter, no matter it’s Digital Unlock

or RF Sensor Unlock. User will need to turn the power back on and re-unlock

again if unlocking is interrupted.

• Scooter cannot be operated unless it’s unlocked (green light on).

Panel Backlight Adjustment (Five levels) ：

• Press the power switch to get the scooter on power

standby (red light on), then press and hold both

acceleration [ ] / deceleration [ ] buttons for 2

seconds. The panel light will be all on when scooter

is ready for backlight setting. (Figure 9)

• Press [ ] to increase level of backlight. Press [ ]

to decrease level of backlight.

• Press the power switch to save the backlight setting

• Panel backlight can be adjusted under power standby mode (red light), user doesn’t have

to unlock the scooter.

Figure 9

REMO AUTO-FLEX Instruction Booklet

Battery / Error Light Indicator ：

The light will be showing the battery status or errors of scooter. If scooter has errors, the light indicator will be flashing (see section 8). This light indicator is also the indication of battery status (see section 6-3). (Figure 10)

Speed Adjustment ：

• Press acceleration [ ] / deceleration [ ] button

to increase / decrease speed.

• There are 3 different speeds of adjustment

fastest 3 > 2 > 1 slowest. (Figure 11)

• Do not set the speed at maximum when operating

the scooter.

• Adjust the speed at maximum when inclining

a slope, and adjust to minimum speed when

declining.

Figure 10

(1) (2) (3)

Head-light / Tail-light ：

• Press button [ ] once to switch on the head-light

and tail - light, the [ ] will be lighted on the panel.

• Switch off by pressing the button again, the [ ]

light will be off on the panel (figure 12)

Tail-light will be on anyway when the brake is engaged and when the scooter speed is reduced.

Horn ：

Press horn button to sound the buzzer. Buzzer sound and light will last until you release the horn button

(Figure 13)

Figure 11

Figure 12

4-2 OPERATION OF MAIN SWITCH

Main Switch (Touch Screen Version) ：

• Press power button to turn on/off (Figure 14)

(see section 4-1 for details)

Main Switch (Key Version) ：

• Turn the key clockwise to turn on,

counterclockwise to turn off (Figure 15)

Figure 13

Sleep Mode ：

• Scooter will go into sleep mode with

one long beep warning sound if no

throttle activity is detected for

programmable time period. (Default

programmable time is 10 mins.)

• When scooter is in sleep mode, all

lights on the control panel will be off,

Figure 14

and the scooter will not respond to commands.

Figure 15

• To wake up the scooter, turn the power (key) switch off and then on again.

REMO AUTO-FLEX Instruction Booklet

4-3 OPERATION OF THROTTLE

Throttle ：

• Pull the right throttle (F) to move scooter forward. Pull the

left throttle (G) to move scooter backward. This can be

reserved if required by local dealer. (Figure 16)

• These are also your accelerator. The further you depress

them, the faster you go. (Subject to the level of speed

adjustment)

• Releasing both left/tight throttles will automatically operate

the brakes to slow down and stop.

(G)

Figure 16

(F)

• Do not pull both right and left throttle at the same time; you might not able to

control the scooter.

• Turning the scooter OFF whilst driving will bring the scooter to an abrupt stop

and danger.

4-4 OPERATION OF FREE-WHEELING (N-D LEVER)

Free-wheeling (N-D Lever) ：

• When lever is in Drive (D) position,

the scooter can be driven. Normal

position is in D (Figure 17)

• When lever is Neutral (N) position,

the scooter can be moved manually

without power (Figure 18)

Figure 17 Figure 18

• Freewheel operation is only recommended on flat surfaces. Never leave your

scooter on gradient with its motors disengaged.

• When adjusting N-D lever, do not sit on the scooter.

• It’s not able to drive the scooter when the lever is in Neutral. You must turn off

the scooter first and switch to D lever, then turn on and drive scooter.

4-5 TILLER HEIGHT ADJUSTMENT

Loosen (counterclockwise) the screw knob to adjust the tiller height, tighten (clockwise) screw knob again to lock at a desired position.

There is a stop point on tiller, the height cannot exceed the stop point (approx. 20cm) (Figure 19)

4-6 SEAT ADJUSTMENT / DISMANTLE

• Please refer to section 5 for scooter folding / unfolding.

• When scooter is being folding, the seat latch will

automatically release and seat will move backwards.

• After unfolding, the seat shall automatically move forwards.

However, please always double check and push the seat

to its locked position) manually if not.

• Do not get on the scooter if the seat is positioned in red

point(H).Get on the scooter only if the seat is locked in its

position green point ( Fig.20)

Figure 19

(H)

Figure 20

REMO AUTO-FLEX Instruction Booklet

Seat Dismantle (Figure 21.22) ：

1.Loosen the screws (L) by hex wrench (Fig.21)

2.Remove the springs (K) connected on the seat slide bracket.

3.Pull down and hold the seat springs (I) and push the seat by thumbs towards the back

of scooter to release the seat from latch (J).

4.When the seat is released from latch, grab the seat and push it towards the back of

scooter to remove the seat.

* When putting the seat back, insert the seat back to seat slide bracket. Push the seat

towards to the front of scooter (green point), fasten the screws (L) and insert the springs

(K) back to seat slide bracket.

* Please make sure to follow the direction of Fig.21 shown when putting springs(K) back

to the bracket.

(K)

(J)

(L)

(I)

Figure 21 Figure 22

• Do not conduct any adjustment (tiller / seat / armrest) while driving the scooter.

• Do not get on the scooter until the seat firmly locks in the position (green point).

• Except for removing seat, do not operate the seat sides spring if no necessary.

• When pulling the seat springs, please grab and hold down both sides springs,

this helps user to easily release the seat latches. The latches may not be release

if the holding point of seat springs is incorrect.

5.FOLDING / UNFOLDING YOUR SCOOTER

Folding / unfolding your scooter only when the scooter is under below circumstances ：

• When the scooter is placed on a flat ground and in lay down position.

• When the scooter is power off and on standby for folding / unfolding, the folding / unfolding

light indicator (M) on scooter will be orange. (Figure 23)

• When the seatback is flip down.

(M)

Folding / Unfolding Buttons ：

• Buttons on scooter (Figure 23)

- Press folding button (N) once to auto-fold; please

make sure the scooter is fully expanded before

folding.

- Press unfolding button (O) once to auto-unfold,

please make sure the scooter is fully folded before

unfolding.

- Press (N) / (O) again to fold / unfold if folding /

unfolding process is interrupted.

• Buttons on remote (Figure 24)

- Press folding button (P) once to auto-fold, please make

sure the scooter is fully expanded before folding.

- Press unfolding button (Q) to auto-unfold, please make

sure the scooter is fully folded before unfolding.

- Press (P) / (Q) again to fold / unfold if folding /

unfolding process is interrupted.

Figure 23

Figure 24

(N) (O)

(P)

(Q)

REMO AUTO-FLEX Instruction Booklet

• The remote is not designed to be water-proof, please keep it away from humid

environment.

• Best transmit range of remote is within 10m. (The reading range will be affected

due to the environment, barrier, and weather).

• The scooter may not be folded / unfolded if the battery is low, please re-charge

the scooter by upper tiller charging port immediately and operate the folding /

unfolding later when the scooter is fully charged. (see section 6-4)

• Keep the remote carefully, it’s highly recommended to chain with RF sensor key.

Please contact dealer if the key is lost.

How to wake up the scooter ：

• Scooter will go into sleep if no throttle activity is detected for programmable time period.

(Default programmable time is 3 mins.)

• Please wake up the scooter before folding / unfolding. There are 3 ways to get the scooter

back on standby for folding/unfolding:

1.Press power switch button and turn off the power.

2.Press and hold the folding button (N) or unfolding button (O) on scooter for 3 seconds

to wake up the scooter, the light indicator (M) will be orange.

3.Press and hold the folding button (P) or unfolding button (Q) on remote for 3 seconds

to wake up the scooter.

How to fold the scooter (Figure 25) ：

1.Turn off the power

2.Flip down the seatback

3.Press folding button on the remote or on scooter once to auto-fold the scooter. The seat

will automatically moving backwards during folding.

4.The seat laches will automatically release and seat will move backwards.

1 2 3

4 5 6

Figure 25

How to unfold the scooter (Figure 26) ：

1.Place the scooter to a flat ground and lay down the scooter

2.Make sure the scooter is power off, however is awake for unfolding (the light indicator

M will be orange).

3.Press unfolding button on the remote or scooter once to auto-unfold

the scooter.

4.When folding and unfolding, the seat shall automatically shift to its position, however,

please double check and push seat to its locked position (green) manually if not.

5.Flip up the seatback and double check if lock is all in its position before you get on the

scooter.

REMO AUTO-FLEX

1 2 3

Instruction Booklet

4 5 6

Figure 26

• Please turn off the power before folding / unfolding, the scooter can only be

folding / unfolding when it is power off, the folding / unfolding

light indicator will be orange.

• There is protection for tapping error; scooter cannot be unfolding when it is in

standing position.

• Actions will stop if any foreign objects are detected during folding / unfolding

process. Please remove the objects and conduct the actions again.

• When operating the remote, please stand beside the scooter for best receiving

signal.

• When operating the folding / unfolding buttons on scooter, please reach the

buttons from the back of scooter. User may get pinched if reaching buttons from

other sides of scooter.

• The scooter may not be folded / unfolded if the battery is low, please re-charge

the scooter by upper tiller charging port immediately and operate the folding

/ unfolding later when the scooter is fully charged. (see section 6-4)

• Check and replace the battery for remote control if the scooter is not able to

fold / unfold.

6.BATTERY GAUGE & CHARGING THE BATTERIES

6-1 DISASSEMBLING BATTERY BOX

• Each battery box contains one lithium battery or (2) lead-acid

batteries (optional).

• To remove the battery box from scooter, grab the battery

box handle, and pull it upwards as Figure.27 shown.

• It’s highly recommended not to remove battery box out if

no necessary. Always keep battery box installed on scooter.

• For any reason to remove the battery box, please make

sure the connectors are in sequence and in position when

put it back to scooter.

Figure 27

• When putting battery box back to scooter, gently press battery box downward

to make sure it is firmly connected to the scooter.

• Do not disassemble battery box and open sealed parts by yourself to prevent

electric shock and damage the battery.

• Maintenance & repair must only be carried out by a competent engineer or

authorized dealer. Please contact dealer if you need to replace internal battery.

REMO AUTO-FLEX Instruction Booklet

6-2 CAUTIONS FOR BATTERY & CHARGER

Lithium Battery ：

• Only certain type and voltage of battery can be used on the scooter. Your scooter may

supply with standard lithium battery or optional lead-acid battery.

• Scooter can be charged when it’s folded or unfolded

• Only use the lithium battery charger (under 4 Amps) supplied with your scooter for lithium

battery.

• Do not switch off, unplug or interrupt the recharge cycle until the charging cycle has

completed (charger indicator turns green)

• If storing your scooter for a prolonged period (1 month or more), storage the batteries

at 30%-50% state of charge at least. Batteries must be recharged once every three

months at least if storing for more than six months. On returning, make sure to charge

them again before using scooter.

• Store the scooter in a dry, well-ventilated environment. Do not store your scooter where

it will be exposed to source of direct heat, damp, oil, acid, alkaline, or where Ozone

could be possibly generated. All of the above will minimize scooter’s lifetime.

• Recommended range of storage : Temperature : 20-30oc, Humidity : 25% ~ 85%, out

of this range might affect the performance of the charger and battery.

• Rough handling operations, throwing, rolling, crushing, shaking, overly strong impact

and extrusion to batteries should be avoided, to prevent battery casing broken or internal

structure damage.

• It’s highly recommended to have your scooter inspected for battery every six month

despite how often you use the scooter. Please contact your dealer.

• Batteries are subject to disposal and recycling regulations that vary by country and region.

Always check and follow your applicable regulations before disposing of any battery.

24V/12A Lead-Acid Battery (optional) ：

• Only certain type and voltage of battery can be used on the scooter. Your scooter may

supply with standard lithium battery or optional lead-acid battery.

• Only use the lead-acid battery charger (under 8 amps) supplied with your scooter for

lead-acid battery

• Adding acid electrolyte to battery is prohibited

• Batteries will only give maximum performance after scooter has been used and batteries

have been recharged several times.

• The minimum time needed to recharge will vary depends on the depletion of the batteries.

Excessive or short period charging will be detrimental to battery life.

• Charge the batteries after each trip. Do not turn the key on while scooter is in charging.

• Please charge the scooter in 0°c ~ 40°c, out of this range might affect the performance

of the charger and battery.

• If storing your scooter for a prolonged period, batteries must be recharged once every

three months at least

• For longest life, your batteries should be recharged regularly. Please recharge the batteries

before they run down to 20%.

• It’s highly recommended to have your scooter inspected for battery every six month

despite how often you use the scooter. Please contact your dealer.

Chargers( lithium / lead-acid) ：

• Do not leave charger plugged into your scooter with charger switched off as this may

discharge your batteries. Always unplug the cables when finishing charging.

• Inspect the battery charger before each use, make sure connectors are dry and clean.

Do not attempt to use an extension cord to plug in your battery charger.

REMO AUTO-FLEX Instruction Booklet

• Be aware that the battery charger case may become hot during charging. Please avoid

skin contact.

• Do not cover charger by any objects. Use the charger in a well-ventilated area. Do not

smoke as explosive gases may be generated while charging the batteries

• Keep the charger stored in a well-ventilated area, do not drop the charger.

• Lead-acid battery charger cannot be alternatively used on lithium battery. Please

only use specific lithium battery charger for your lithium battery. Lead-acid battery

charger can be used only if your scooter comes with lead-acid batteries (optional).

(Please see section 9-1 for details)

• If you want to change to optional lead-acid batteries, please contact dealer to

reset the battery system such as charging port and controller setting.

• Please keep the above cautions in mind. Any battery / charger faults due to the

unauthorized maintenance, dismantle, misuse or accidental damage is not

covered by the manufacturer’s warranty.

6-3 BATTERY GAUGE

There is an indicator shows battery capacity status (Figure 28) ：

• Touch screen version : 6 segments

• Key Switch version : 5 segments

• When battery gauge light trends to right (green), it indicates sufficient power capacity.

• When battery gauge light trends to left (red), it indicates insufficient power capacity.

• Check battery capacity before driving. Recharge

the battery immediately when the red light is flashing

as the remaining power can only keep scooter going

for buffering 2 km or less

• Displayed segments on panel are for reference

only. Please refer to LED indicator of charger for

more accurate charging status.

• The scooter may not be able to fold/unfold when

the battery capacity status is less than 3 segments,

please recharge the battery immediately.

Figure 28

6-4 OPERATING THE CHARGER

Batteries must be charged before using the scooter for the first time and should be recharged after each day use.

Your scooter may come with standard lithium 24V/2A charger, or optional bigger 24V/4A charger if you upgrade the lithium battery to 17.4Ah . Your scooter may come with 24V/2A lead-acid charger if you optionally choose lead-acid battery for your scooter.

Do not alternatively use lead-acid charger to charge lithium battery, they are not compatible and may cause damages and dangers if doing so.

Lithium Battery Charger ：

• Output Voltage: 100V~240V (Figure 29)

1.Charger output cable, 4pins connector (R)

2.AC power cord (S)

3.LED Indicator (T)

- RED LIGHT ON : Pre-charging

- ORANGE LIGHT ON : Normal Charging

- GREEN LIGHT ON: Fully Charged.

(R)

(S)

Figure 29

(T)

REMO AUTO-FLEX Instruction Booklet

Lead-acid Battery Charger ：

• Output Voltage: 100V~240V (Figure 30)

1.Charger output cable, 3pins connector (U)

2.AC power cord (V)

3.LED Indicator(W)

- RED LIGHT ON : Pre-charging

- ORANGE LIGHT ON : Normal Charging

- GREEN LIGHT ON: Fully Charged.

(V)

(U)

Figure 30

(W)

• Each country may supply different charger. The charging procedure may be

different from below. Chargers for lithium battery and lead-acid battery (optional)

are different.

• The charger LED light should indicate red when pre-charging. If not, please

contact your authorized dealer.

• Inspect the battery charger before each use, make sure connectors are dry and

clean. Do not attempt to use an extension cord to plug in your battery charger.

• Do not use other brand of charger to charge the scooter, only use the charger

equipped with originally

• The battery charger is equipped with cooling fan. If the fan does not appear to

be working correctly, please turn off the charger immediately as it may be

overheated. Please contact your authorized scooter dealer.

• Do not leave charger plugged into your scooter with charger switched off as this

may discharge your batteries. Always unplug the cables when finishing charging.

• Be aware that the battery charger case may become hot during charging. Please

avoid skin contact.

• Keep the charger stored in a well-ventilated area, do not drop the charger.

Charging Operation ：

There are two charging ports, one is on upper of scooter, and the other is on battery box.

Upper Charge Port (Figure 31)

• Open the charge port cap

1.Insert the charger output cable into the charge port

2.Plug the AC cord into a standard electrical outlet on the wall

3.Check the charger LED indicator; make sure it’s in normal charging. During charging,

LED will indicate orange light.

4.When unplug, please make sure to remove the AC cord from the wall first, and then

charger output cable from the charge port.

1 2 3 4

Figure 31

• Battery Box Charge Port (Figure 32)

1.Remove the battery box from the scooter and place it on a flat ground.

2.Open the charge port cap and connect the charger output cable into the charge port

3.Plug the AC cord of charger into a standard electrical outlet

4.Check the charger LED indicator; make sure it’s in normal charging. During charging,

LED will indicate orange light.

REMO AUTO-FLEX Instruction Booklet

5.When unplug, please make sure to remove the AC cord from the wall first, and then

charger output cable from the charge port.

6.put the cap back to cover charging port before install the battery box back to scooter.

1 2 3 4

Figure 32

• Be sure the scooter key (power) is in the OFF position when charging.

• The time needed to recharge will vary depending on the depletion of the batteries.

Charging for longer than necessary will not harm the batteries. It cannot be

over-discharged.

• When remove / install the battery box, please make sure the connectors are

in sequence and in position to avoid electric damage.

• Please keep the above cautions in mind. Any battery / charger faults due to the

unauthorized maintenance, dismantle, misuse or accidental damage is not covered

by the manufacturer’s warranty

• Do not alternatively use lead-acid charger to charge lithium battery, they are

not compatible and may cause damages and dangers if doing so.

7.CARE AND MAINTENANCE

7-1 INSPECTION CHECKS

Daily Check :

Please always check your scooter before you start your every journey.

Check point

N-D leaver

Inspection

Check for correct function.

What to do if the inspection is failed

Contact your dealer.

Horn Contact your dealer.

Throttles

Remote / foldingunfolding buttons on scooter

RF Sensor Key

Folding / unfolding

Release lever

(manual version)

Check for correct function.

Pull the wigwag to test the scooter movement. Pull the wigwag a little bit and release it to test if brake works.

Check if Remote control for folding / unfolding works. Check if folding / unfolding buttons on scooter works.

Check for correct function.

Check if folding / unfolding function is normal

Contact your dealer, the electromagnetic brake should be clean by brush regularly.

• Replace the battery for remote control.

• Contact your dealer.

Contact your dealer.

Battery Gauge

Battery box

Lighting

Check if the battery gauge is displayed and whether it is at low power.

Check if there is cracks or damage, and if it’s firmly installed to the scooter.

Check if all lights, such as head lights, rear lights, and turn signal are functioning correctly.

• Contact your dealer if battery gauge is

not working.

• Recharge the battery immediately if low.

Contact your dealer

Contact your dealer.

REMO AUTO-FLEX Instruction Booklet

WEEKLY CHECK

Check point

Armrests

Wheels / Tires

Motor

Battery Charger

Inspection

Check if the parts are clean and firmly tighten to the scooter and do not wobble. Tighten the screw knob that holds the armrest.

Check if the tire has cracks, deformation, and check that wheels rotate without wobbling. Tire tread depth is not less than 0.5mm.

No foreign objects in tires.

Check for correct function, no noisy sound.

Check if the charger is functioning correctly and the batteries are charged.

What to do if the inspection is failed

Contact your dealer.

MONTHLY CHECK

Check point

Seat / Upholstery

Tiller fixation

Inspection

Check for movement and seat lock and if upholstery is worn.

Check for all fasteners

What to do if the inspection is failed

Fasten the screws if it’s loosen Contact your dealer if upholstery is worn.

Contact your dealer

EVERY SIX MONTHS CHECK

Check point

Electronics

Inspection

Check if all the battery cables and connectors are firmly tighten to the scooter.

What to do if the inspection is failed

Contact your dealer.

Please take your scooter to a qualified technician for a thorough inspection and servicing every six months.

7-2 CLEANING AND MAINTENANCE

• User should inspect the scooter regularly to keep scooter in good running order.

• User should inspect the scooter more often especially when the scooter has possibly

been riding on the bad road condition such as, grass, sand, bumps, and potholes.

• Please turn off the scooter and remove the key and make sure the lever is in D position

before inspection to avoid roll-away.

• Please avoid any tapping error on remote or scooter for folding/unfolding when carrying

the maintenance work.

• Do not use any abrasive or scouring liquids for cleaning. Only use a damp cloth and

gentle detergent.

• Do not use hose pipe or splash water directly onto the scooter as this may cause damage

to electronics.

Seat Upholste :

Only use damp cloth and a mild soap to wipe the seat. Do not use abrasive cleaners as this will damage the seat. Do not sit until the seat dries out.

Frame / Shroud :

Only use damp cloth to wipe. Do not use abrasive cleaners as this will damage the parts.

When scooter dries out, the shroud can be applied with a light of wax to keep its gloss.

REMO AUTO-FLEX Instruction Booklet

Tire :

Only use damp cloth to wipe. Do not use abrasive cleaners as this will damage the parts.

User should inspect the tires frequently for damage, the presence of foreign bodies, unusual wear and sufficient tread depth. If replacement of tires are needed, please contact the nearest dealer.

The following areas require periodic inspection: Tread depth drops below 0.5 mm.

Storage :

• If store the scooter in long time (one week or more), please disconnect the battery

terminals and do not connect battery terminal [+] [-] with any metals to avoid danger.

• When store scooter, make sure the power is off, seat lock is fixed, and N-D lever is in D

position to engage brake to avoid roll-away.

• Please store the scooter in a dry location. Do not store your scooter where it will be

exposed to source of direct heat, damp, oil, acid, alkaline, or where Ozone could be

possibly generated. All of the above will minimize scooter / tire cycle and shorten its

lifetime. Recommended range of storage for the scooter is as below :

• Temperature (with lithium battery) : -20 o c ~ +50 o c / Humidity : 25% ~ 85%

• Temperature (with lead-acid battery) : -30 o c ~ +50 o c / Humidity : 25% ~ 85%

• If the storage environment is out of the range, we suggest you to take out the battery

box from scooter and store it respectively.

All maintenance and repair of scooter MUST be done by an authorized dealer. ANY unauthorized adjustments, repair or service to the scooter may result injury to yourself or damage to scooter.

REMO AUTO-FLEX Instruction Booklet

8.TROUBLE SHOOTING

Here are some suggestions about solving problems you may have with your scooter. There is a self-diagnostic warning light on the control panel. To check the self-diagnostic warning light, turn on the key (power) switch (see section 4-2) and count the number of blinks on the warning light.

Touch Screen version ： Key Switch Version ：

Figure 33

Normal : Solid light

Abnormal : flashing light Figure 34

Normal : Solid light

Abnormal : flashing light

Self-Diagnostic Warning Light

Flash

Description

Battery Low

Low Battery Fault

High Battery Fault

Current limit time-out or controller overheat

Park Brake

Drive Inhibit

Speed Pot

Motor Voltage

Other Error

Initial check points

The batteries are running low.

• Recharge the batteries.

The batteries have run out of charge.

• Recharge the batteries.

• Check the battery and associated connections and wiring.

Battery voltage is too high. This may occur if overcharged and/or traveling down a long slope.

• If traveling down a slope, reduce your speed to minimize the

amount of regenerative charging.

The motor has been exceeding its maximum current rating for too long.

• The scooter may have stalled. Turn the controller off, leave for a few

minutes and turn back on again.

• The motor may be faulty. Check the motor and associated

connections and wiring.

Either a park brake release switch is active or the park brake is faulty.

• Check the park brake and associated connections and wiring.

• Ensure any associated switches are in their correct positions.

• Switch to D (drive) position. Turn off the power and turn on again.

Either a stop function is active or charger inhibits or OONAPU condition has occurred.

• Release the stop condition (seat raised etc.)

• Disconnect the battery charger.

• Ensure the throttle is in Neutral when turning the controller on.

• The throttle may require re-calibration.

• The folding/unfolding procedure is uncompleted.

The throttle, speed limit pot. SRW or their associated wiring may be faulty.

• Check the throttle and speed pot and associated connections and wiring.

The motor or its associated wiring is faulty.

• Check the motor and associated connections and wiring.

The controller may have an internal fault.

• Check all connections and wiring.

• If self-diagnostic warning lights with 1 / 2 / 4 / 5 times, please refer to above for solutions

(turn off and restart again or charge the battery). If none of above correct problem,

contact your authorized dealer.

• If self-diagnostic warning lights with 3 / 6 / 7 / 8 / 9 times, please contact your authorized

dealer directly.

REMO AUTO-FLEX Instruction Booklet

Folding / Unfolding Errors ：

Here are some suggestions about solving problems you may have when folding / unfolding your scooter. The scooter will stop the folding / unfolding actions if errors are detected.

Please refer to below table and correct the problems.

Figure 35 Figure 36

Flash

Description

Power On

Battery Low

Seat springs fall off

Seatback is not flipped down

What to do

Please turn of the power of scooter (see section 4-2) and restart the folding / unfolding procedure.

The batteries are running low. Recharge the batteries and restart the folding/unfolding procedure. (see section 6-4)

Please contact your dealer.

Flip down the seatback and restart the folding / unfolding procedure.

Scooter is not on flat ccground

Foreign Object on footplate.

Foreign Object underneath the seat

Scooter cannot be folding/unfolding if it’s not placed (lay down) on a flat ground. Please place the scooter on a flat ground and restart the folding / unfolding procedure.

Check and remove the object on the footplate and restart the folding / unfolding procedure.

Check and remove the object underneath the seat and restart the folding / unfolding procedure.

Folding / unfolding light indicator on scooter is not in orange (auto version)

Auto version: please wake up the scooter ( see section 5)

Folding / unfolding

Release lever is stuck

(manual version)

Hold and pull the seat base backwards with one hand while pulling the release lever with the other hand.

• If none of above correct problem, contact your authorized dealer. Do not dissemble the

scooter by yourself.

REMO AUTO-FLEX Instruction Booklet

9.OTHER INFORMATION

9-1 Options

We offer below options to add functionality for your scooter, please contact the authorized dealer for more information.

• We reserve the rights to modify or change the accessories.

• Please read through the cautions for battery and charger (section 6) if optional lead-

acid battery is purchased.

• Scooter folding / unfolding process may be interfered with optional accessories (armrests,

bags) equipped. Please remove these accessories before folding/unfolding the scooter

(accessories such as optional bigger battery will not affect the folding / unfolding, you

don’t have to remove the battery box).

Figure 37

Item

Bag (Front)

02 Adjustable Armrests

Bag

(underneath the seat)

04 Seat Belt

05 Bag (seatback)

06 Lead-acid Battery Pack

Lithium Battery Pack

(bigger capacity 17.4AH)

Lithium Battery Charger

(bigger capacity 24V/4A)

Compact Armrests

Screws Knob for

Armrests

Carry Cover Bag

12 Storage Cover

Qty

Description

Anti-splash, max. loading weight of 2Kgs.

To be installed on the front tiller.

Multi-Adjustable with height and flip angles.

Anti-splash, max. loading weight of 2Kgs.

To be installed underneath the seat.

To be installed for extra safety.

Anti-splash, max. loading weight of 2Kgs.

To be installed on the seatback.

With 12Ah lead-acid battery, comes with 24/2A lead-acid charger( Do NOT use it on lithium battery)

Charging port for lead-acid charger : 3 ports

With bigger 17.4Ah lithium battery, comes with 24V/4A lithium charger. (see item 8 for charger details)

To be used on 17.4 lithium battery pack, can be used on

11.6Ah lithium battery also. However, do NOT use it on lead-acid battery.

Charging port for lithium charger : 4 ports

Power Light : Red (power on)

Charge Light : Red (normal charging) /

Green(fully charged)

Compact armrests adjustable with flip angle.

For armrests fixation.

making sure your scooter remains dry and safe from incurring any damage.

Overall Width

Overall Height

Front Wheels

Rear Wheels

Weight W/ Batteries

Max. Speed

Weight Capacity

Ground Clearance

Grade Climbable

Curb Climbable

Turning Radius

Brake

Seat Type

Seat Width

Motor Size

Battery Size

Battery Weight

Travel Range

Battery Charger

Electronics

REMO AUTO-FLEX

10.TECHNICAL SPECIFICATIONS

Specification

Overall Length

Instruction Booklet

Auto-folding

Folded : 30.5"

Unfolded : 37.5"

Folded : 19.4"

Unfolded : 19.7”

Folded : 20.1"

Unfolded : 37.8"

8”

67.5 lbs

5 mph

255 lbs

1.7”

6 degree

1.6”

44.1"

Electro-Mechanical

Padded Foldable

16"

250W, 4900 r.p.m

24V. 11.6 Ah

6.2 lbs

7.5 Miles

2A Off Board

Sensor Key, Touch Screen, Coded Lock,

Remote Control for Auto-Folding

*Subject to change without notice.

( Rev. 0, 2019/03/11 )

Hello! I am an AI chatbot specifically trained to assist you with the REMO AUTO-FLEX Instruction Booklet. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated