TXDi- series
VER 201
Vehicle Weighing Scale
OWNER’S MANUAL
Vehicle Weighing Scale TXDi- series
NOTE
(1) The unauthorized copying of some or all of this manual is prohibited.
(2) The information contained herein is subject to change without notice.
(3) If there are any questions such as wrong or missing parts of the contents listed in this manual, please contact us.
(4) To improve the product performance, functions can be changed with no notice.
(5) Please understand that TMT does not have responsibility for a demand related to loss, lost profit etc. caused by operating the product, regardless of the third clause.
WARNING DEFINITIONS
This is warning & caution mark
This is hazard alert mark
This is useful information mark
- 2 -
Vehicle Weighing Scale TXDi- series
INDEX
1. Precautions ............................................................................. 4
2. Introduction ............................................................................. 5
3. Installation ............................................................................... 5
4. Use of Battery Pack ................................................................ 7
5. Description of Panels and Symbols ......................................... 8
6. Setting Mode ........................................................................... 9
7. Power Saving Mode .......................................................... 11
8. Test Mode ............................................................................. 12
9. Paring Mode ......................................................................... 13
10. Pad to Pad Communication .................................................. 13
11. Specifications ...................................................................... 14
12. Check Message .................................................................. 17
- 3 -
Vehicle Weighing Scale TXDi- series
1. Precautions
Please be informed that we’re not responsible for any incident or mishap caused by partial modification of this product. To avoid such situation, customers need to contact our customer service team or system installation staff in advance, and any modification should be conducted under our surveillance.
◆ Use only approved enhancements and batteries. Do not connect incompatible products. Use only batteries, chargers, adaptor, and enhancements approved by TMT for use with this particular model.
The use of any other types may invalidate any approval or warranty, and may be dangerous. For availability of approved enhancements, please check with your dealer.
◆ Do not install the scale in strong direct sunlight and dust.
◆ Please confirm that the local voltage is correct for the power adapter.
◆ Do not use inflammable substances for cleaning.
◆ Avoid sudden changes of temperature if possible
◆ Do not use the product in a place with a high-voltage current or severe electronic noise.
◆ Do not use the product in a place with severe vibration.
◆ Do not put too much pressure to keys.
◆ Avoid from the shock of excessive weight.
◆ MICRO USB-B port is for firmware update.
Do not connect for any other purpose.
- 4 -
Vehicle Weighing Scale TXDi- series
2. Introduction
◆ Easy to exchange the battery pack.
◆ Slim(34mm) type.
◆ Weigh-In-Motion(WIM)
◆ Outstanding water resistant(IP66) and vibration proof effect.
◆ Wireless communication: ZigBee
◆ Long battery lifetime by one time charging
3. Installation
Be cautious of below situations, when placing the product on the road.
- 5 -
Vehicle Weighing Scale TXDi- series
Weighing method
Sequential
2 Axle, 2 Plate
Accuracy: ±1~3%
(WIM: ±3%)
[Scale ID]
Axle 1 ☞ Left: 1 / Right: 2
Description
In case of Weigh-In-Motion (WIM), you must install the dummy pad (longer to the length of the vehicle) back and forth on scale.
Synchronous
2 Axle, 4 Plate
Accuracy: ±0.1%
[Scale ID]
Axle 1 ☞ Left: 1 / Right: 2
Axle 2 ☞ Left: 3 / Right: 4
Synchronous
3 Axle, 6 Plate
Accuracy: ±0.1%
[Scale ID]
Axle 1 ☞ Left: 1 / Right: 2
Axle 2 ☞ Left: 3 / Right: 4
Axle 3 ☞ Left: 5 / Right: 6
Can be installed up to maximum 6 axles
As shown above, if it is used with the indicator, please refer to indicator ’s operating manual.
- 6 -
Vehicle Weighing Scale TXDi- series
4. Use of Battery Pack
Use only approved power adaptor and batteries.
Do not connect incompatible products.
The use of any other types may invalidate any approval or warranty, and may be dangerous. For availability of approved enhancements, please check with your dealer.
4.1. Indicate battery level
The battery level is displayed for a while when the power is turned on.
(Display in 10% increments)
Ex : BAT 70 (70%)
4.2. Battery charging
Step1. Turn clamps that exit on both sides of battery cover to the right in a quarter.
Step2. Pull out a battery.
Step3. Check the battery polarity and insert it into the charger.
Step4. The RED lamp lights up when charging.
Step5. If a charging is completed, the GREEN lamp is on.
Step6. The battery charging time takes about 3~6 hr.
(Charging time is subject to be changed according to battery condition & capacity.)
4.2. Battery lamp
In order to prevent the electric discharge, after r is on , the power will be turned off automatically after about 1~5 hours.
(It’s subjected to be changed according to using conditions.)
- 7 -
Vehicle Weighing Scale TXDi- series
5. Description of Panels and Symbols
Display
88888
Indicates weight and status
Displayed when the weight is minus
Indicates when a battery has to be recharged
Displayed when the weight is zero
Slip mode (Only works in static mode)
Indicates in-motion mode(TXI-500F + TXDi)
Communication between pads (TXDi + TXDi)
Total weight display pads (TXDi + TXDi)
Indicates the weighing unit kg
Indicates the weighing unit lb
Displayed when the weight is stable
Key
Turn on and off the scale.
Return the display to zero
(Operate within 10% of capacity)
Total display mode on and off
Total display mode can’t be run one or more and can’t be operated in WIM mode.
Press and hold this key for 2 seconds, Use to change weight unit
The scale’s unit is also changes
Press this key , use to back light on and off
- 8 -
Vehicle Weighing Scale TXDi- series
6. Setting Mode
How to enter When the display is off, press setting mode is stared.
key while pressing key then this
Used keys
:Used to set up an initial zero value / Increase the digit of value (F03)
: Used to increase the setting constant one by one.
: Used to move next menu after completing input value.
F01
(01 ~ 09)
Adjustment the speed of weight change (Initial value : 5) ex) F01-1: Very fast ~ F01-9: Very slow
F02
(00 ~ 99)
Automatic zero condition (Initial value : 2) ex) F02-0 : Not used
F02-3: Compensation for gradual change below 1.5division.
F02-9: Compensation for gradual change below 4.5division.
F03
(01 ~ 99)
Scale ID number (Initial value : 1) ex) F03-1: ID 1 , F03-12 : ID 12
F04
(0, 1)
Weighing-In-Motion (WIM) (Initial value : 0) ex) F04-0: Not used / F04-1: Used
In the WIM mode
When “ SLO” , “ FAST” message occurs, in order to initialize, press key. Then, must be measured weight again.
Maximum vehicle speed: 10km/h (6mi/h)
F05
(0 ~ 5)
F06
(0 ~ 9)
Adjusting the brightness of the backlight (Initial value : 2) ex) F05-0: 0% brightness ~ F05-3: 60% brightness
Display speed (Initial value : 5) ex) 50msec, ~ 9 : 500msec
F07
(0 , 1)
Backup mode (Initial value : 0) ex) F07-0: normal, F07-1 : backup
- 9 -
Vehicle Weighing Scale TXDi- series
F08
(00 ~ 99)
Stable division (Initial value : 2) ex) F08-04 : 1division , F08-08 : 2division
F09
(00 ~ 99)
Stable time (Initial value : 20) ex) F08-02 : 0.2sec , F08-20 : 2sec
F10
(0 , 1)
F11
(0 , 1)
F12
F13
F14
(0 , 1)
Zero key (Initial value : 0) ex) 0: steady, 1 : Anytime
Backlight color (Initial value : 1)
0 : ember , 1 : green
No function
No function
Sleep mode buzzer (Initial value : 0) ex) 0: Not used , 1 : Used
F15
(00 ~ 99)
Sleep mode time (Initial value : 0) ex) 0: Not used , 1 : 5sec , 6 : 30sec
F16
(01 ~ 99)
Sleep mode weight division (Initial value : 3) ex) 1 : 5division , 5 : 5division
F17
(00 ~ 16)
Number of pads to be linked wireless (Initial value : 0) ex) 0: Not used(TXI-500F + TXDi), 4: 4 Pads linked (TXDi + TXDi)
- 10 -
Vehicle Weighing Scale TXDi- series
7. Power Saving Mode
Up to 120 hours(static) of use(in motion 70 hours)
Based on using Power Saving mode, 3.7V 3500m
(When not using power saving mode Max 50 hours)
◆ Enter Power Saving mode
Condition 1 : Weight stable
Condition 2 : Weight is within zero point + set value (F16)
Condition 3 : When condition 1 is satisfied for the set time(F15)
◆ Exit Power Saving mode
Condition 1 : Unstable weight
Condition 2 : or or Key press
(static : When key is pressed for more than 0.5 seconds)
Condition 3 : When the weight exceeds the zero point + set value(F16)
◆ Confirmation or precautions when using power saving mode
- During power saving mode, the zero key command sent by the indicator(TXI-500F) is not recognized.
- The indicator's(TXI-500F) power off synchronization does not work during power saving mode.
- During power saving mode, the * key mode switch function of the indicator(TXI-500F) does not work. (TXI-500F, F19-1)
- While the pad is in power saving mode, turning on the indicator(TXI-500F) will display a communication error with the pad.
- When exiting the power saving mode, there may be a slight error from the set value(F16).
(At this time, the weighing is for exiting the power saving mode and there is no error in the weight if it is not in the power saving mode.)
-
-
While the pad is in power saving mode, the pad does not operate on the indicator(TXI-500F) commands .
- 11 -
Vehicle Weighing Scale TXDi- series
If there is a pad that has entered the power saving mode, do not use key(Unit change key)
(It changes to the unit of weigh of the pad that wakes up in power saving mode)
8. Test Mode
How to use When the display is off, press then this test mode is stared.
key while pressing key
Used keys
: Used to test the scale.
: Used to move next menu.
TEST1
0
TEST 1 : Key test
Initial display is ‘0’.
Press a key that you want to test, and then the display message will be shown. ( :1 / : 2 / : 3 )
TEST 2
TEST 2 : Display test
It operates automatically and the whole display is ON.
TEST3
5138
TEST 3 : Load cell test
The value is the conversion constant for A/D.
The value may be different according to scale models.
Please check if the displayed number is easily changed with giving force to a scale.
If the displaying number is not changed or remains ‘0’, then it needs the service after sales.
TEST4
LIGHT
TEST 4 : Back light test
: Turn on and off the back light.
: Change color
TEST5
BATTERY TEST(%)
- 12 -
Vehicle Weighing Scale TXDi- series
9. Paring Mode
Step 1 turn on the power during you press Key.
Step 2
Step 3
When you can see G-CAL on the screen, press again
F17 – 2~16 :
Key once
After SEL appear on screen, if you can press again on Master, there will appear MST .
Key once
In this case, press
F17 – 0 :
RFSET appear and wait
key, SLV appear on screen.
(Waiting for indicator(master) pairing signal)
Step 4 When you press key on MASTER and finish PAIRING mode, move to weight measurement mode.
* The Equipment numbers for each pad designate on F03 and total connect pad quantity designate on F17.
* You can see the total amount of the weight for each pads when you press
10. Pad to Pad Communication(F17 - 2~16)
◆
◆
It does not neter power saving mode while Lamp displayed
When is displayed all keys are synchronized between pads
key.
◆
(If you want to use keys that apply only to each pad, use to terminate the communication)
Changed to the unit weight of the pad showing the total weight
key
(changed to the unit weight of the pad pressing key
- 13 -
Vehicle Weighing Scale TXDi- series
11. Specifications
◆ TXDi - 501F / 502F / 505F
Model
Capacity
Division
TXDi -501F
2,000 lb /
1,000 kg
2 lb / 1 kg
TXDi 502F
4,000 lb /
2,000 kg
5 lb / 2 kg
TXDi -505F
10,000 lb /
5,000 kg
10 lb / 5 kg
TXDi-505F
(NTEP CLASS IIII)
10,000 lb /
4,540 kg
50 lb / 20 kg
Dimensions
Platform size
Net weight
Operating time
◆ TXDi - 710F / 715F
Model
Capacity
Division
TXDi -705F
(NTEP CLASS IIII)
10,000 lb /
4,540 kg
50 lb / 20 kg
674 x 532 x 50 (mm)
500 x 380 x 34 (mm)
Approx. 17 kg (Included ramp)
Approx. 50 hr , 120hr(power save mode)
TXDi -710F
(NTEP CLASS IIII)
20,000 lb /
9,080 kg
TXDi -710F
20,000 lb /
10,000 kg
50 lb / 20 kg 20 lb / 10 kg
886 x 730 x 50 (mm)
TXDi -715F
30,000 lb /
15,000 kg
20 lb / 10 kg
Dimensions
Platform size
Net weight
700 x 500 x 34 (mm)
Approx. 23.5 kg
Ramp weight
Operating time
◆ TXDi - 910F / 915F / 920F
Model
Capacity
Division
Approx. 50 hr , 120hr(power save mode)
TXDi -910F
20,000 lb /
10,000 kg
20 lb / 10 kg
Approx. 1.6 kg x 2 pcs
TXDi -910F
(NTEP CLASS IIII)
20,000 lb /
9,080 kg
50 lb / 20 kg
TXDi -915F TXDi -920F
30,000 lb /
15,000 kg
40,000 lb /
20,000 kg
20 lb / 10 kg 50 lb / 20 kg
Dimensions
Platform size
Net weight
Ramp weight
Operating time
1066 x 840 x 50 (mm)
900 x 500 x 34 (mm)
1066 x 940 x 50
900 x 600 x 34
Approx. 28 kg Approx. 36 kg
Approx. 2.9 kg x 2 pcs
Approx. 50 hr , 120hr(power save mode)
- 14 -
Vehicle Weighing Scale TXDi- series
◆ General specification
Operating time
Safe overload
Display
Backlight
Output data rate
Temperature
Operating humidity
Power
◆ Wireless specification
Wireless method
RF frequency range
Output power
Channel width
Frequency offset
Transmit data rate
Receiver sensitivity
Maximum input level
RF In/out impedance
Spurious (2nd harmonics)
Radio link effective range
120hr (static) , 70hr(in motion)
150% of capacity
6 digit FSTN LCD (Height: 15mm)
Amber LED backlight
10 times/sec(Static), 100 times/sec (WIM)
-20 ℃ ~60 ℃
85% R.H. (No condensation)
3.7V 3.5A Lithium ion battery (18650)
ZigBee
2400 ~ 2483.5 MHz
Max. 6.479dBm
5 MHz
< ±30ppm
250Kbps,500Kbps
-99dBm (PER <1%)
0dBm
50 ohm (TXRF, RXRF)
< -30dBm
Approx. 30M (Open space)
- 15 -
Vehicle Weighing Scale TXDi- series
◆ TXDi-501F / 502F / 505F Dimensions [mm]
◆ TXDi- 710F / 715F Dimensions [mm]
◆ TXDi-910F / 915F Dimensions [mm]
- 16 -
Vehicle Weighing Scale TXDi- series
12. Check Message
Code Description
CH 01
Calibration resolution over 1/30000
CH 02
A/D not stable
CH 03
When the weight value is not correct in the calibration
CH 04
When there is something wrong with the stored memory
CH 05
When the entered value is out of range
CH 06 When there is error more than 20% of calibration zero point when power is ON
ERROR0
System error(Remove and reinsert the battery)
FAST In the WIM, occur when the vehicle’s speed is too fast.
Please pass the vehicle with 10km/h(6mi/h) or less.
SLO
In the WIM
, occur when the vehicle’s speed is too slow.
OVER
The scale
’s weight is over maximum capacity.
Don ’t load the article whose weight is heavier than the maximum capacity.
CELL
No load cell connection
RF-ERR Pairing Error
RFXX
No wireless connection (XX : pad number)
(TXDi + TXDi : Last pad number that could not be communicated)
BAT LO Low battery level(Power turns off after display)
- 17 -
[MEMO]
Vehicle Weighing Scale TXDi- series
- 18 -
