Viking Pump TSM142.2: LS-M225/4225 Service Manual

Add to My manuals
14 Pages

advertisement

Viking Pump TSM142.2: LS-M225/4225 Service Manual | Manualzz

Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com

TECHNICAL SERVICE MANUAL

HEaVY-DUTY BRaCKET MOUNTED PUMPS

SERIES 225 aND 4225

SIzES lS, Q, QS, M

SECTION TSM 142.2

PAGE

ISSUE

1 Of 14

E

CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information. . . . . . . . . . . . . . . . . . . . 2

Special Information . . . . . . . . . . . . . . . . . . . 3

Maintenance . . . . . . . . . . . . . . . . . . . . . . 4

Packed Pumps . . . . . . . . . . . . . . . . . . . . . 5

Disassembly . . . . . . . . . . . . . . . . . . . . . 6

Assembly . . . . . . . . . . . . . . . . . . . . . . . 7

Mechanical Seal Pumps . . . . . . . . . . . . . . . . 8

Disassembly . . . . . . . . . . . . . . . . . . . . . 9

Assembly . . . . . . . . . . . . . . . . . . . . . . .

10

Thrust Bearing Adjustment . . . . . . . . . . . . . . .

12

Installation of Carbon Graphite Bushings . . . . . . . .

12

Pressure Relief Valve Instructions . . . . . . . . . . 13

INTRODUCTION

SIzE lS - FIgURE 1

(Shown with Jacketed Head Plate)

OBSOLETED model number and serial number of pump when ordering repair parts. The unmounted pump or pump unit model number and serial number are on the nameplate.

PRODUCT

UNMOUNTED PUMP UNITS

PACKED MECH. SEAL Units are designated by the unmounted pump model

LS225 LS4225 numbers followed by a letter indicating drive style.

Q225 Q4225

QS225

M225

QS4225

M4225

V = V-belt

D = Direct Connected

R = Viking Speed Reducer

P = Commercial Speed

Reducer

SIzES Q, QS aND M - FIgURE 2

(Shown with Jacketed Relief Valve Type Head)

This manual deals only with Series 225 and 4225 Heavy

Duty Bracket Mounted Pumps. Refer to Figures 1 through

13 for general configuration and nomenclature used in this manual. Pump specifications and recommendations are listed in Catalog Section 142, Series 225 and 4225 Heavy

Duty Bracket Mounted Pumps.

VIKING PUMP, INC.

A Unit of IDEX Corporation

Cedar Falls, IA 50613 USA

SaFETY INFORMaTION aND INSTRUCTIONS

IMPROPER INSTallaTION, OPERaTION OR MaINTENaNCE OF PUMP MaY CaUSE SERIOUS INJURY

OR DEaTH aND/OR RESUlT IN DaMagE TO PUMP aND/OR OTHER EQUIPMENT. VIKINg’S WaRRaNTY

DOES NOT COVER FaIlURE DUE TO IMPROPER INSTallaTION, OPERaTION OR MaINTENaNCE.

THIS INFORMaTION MUST BE FUllY REaD BEFORE BEgINNINg INSTallaTION, OPERaTION OR

MaINTENaNCE OF PUMP aND MUST BE KEPT WITH PUMP. PUMP MUST BE INSTallED, OPERaTED aND MaINTaINED ONlY BY SUITaBlY TRaINED aND QUalIFIED PERSONS.

THE FOllOWINg SaFETY INSTRUCTIONS MUST BE FOllOWED aND aDHERED TO aT all TIMES.

Symbol legend :

!

Danger - Failure to follow the indicated instruction may result in serious injury or death.

WaRNINg

Warning - In addition to possible serious injury or death, failure to follow the indicated instruction may cause damage to pump and/or other equipment.

WaRNINg

!

BEFORE opening any liquid chamber (pumping chamber, reservoir, relief valve adjusting cap fitting, etc.) be sure that :

● Any pressure in the chamber has been completely vented through the suction or discharge lines or other appropriate openings or connections.

● The pump drive system means (motor, turbine, engine, etc.) has been “locked out” or otherwise been made non-operational so that it cannot be started while work is being done on the pump.

● You know what material the pump has been handling, have obtained a material safety data sheet (MSDS) for the material, and understand and follow all precautions appropriate for the safe handling of the material.

!

WaRNINg

USE extreme caution when lifting the pump. Suitable lifting devices should be used when appropriate. Lifting eyes installed on the pump must be used only to lift the pump, not the pump with drive and/or base plate.

If the pump is mounted on a base plate, the base plate OBSOLETED product catalog.

BEFORE operating the pump, be sure all drive guards PRODUCT

!

!

!

WaRNINg

!

WaRNINg piping is not connected.

DO NOT place fingers into the pumping chamber or its connection ports or into any part of the drive train if there is any possibility of the pump shafts being rotated.

DO NOT exceed the pumps rated pressure, speed, and temperature, or change the system/duty parameters from those the pump was originally supplied, without confirming its suitability for the new service.

BEFORE operating the pump, be sure that:

● It is clean and free from debris

● all valves in the suction and discharge pipelines

are fully opened.

● All piping connected to the pump is fully supported

and correctly aligned with the pump.

!

!

WaRNINg

DO NOT attempt to dismantle a pressure relief valve that has not had the spring pressure relieved or is mounted on a pump that is operating.

aVOID contact with hot areas of the pump and/or drive. Certain operating conditions, temperature control devices (jackets, heat-tracing, etc.), improper installation, improper operation, and improper maintenance can all cause high temperatures on the pump and/or drive.

THE PUMP must be provided with pressure protection.

This may be provided through a relief valve mounted directly on the pump, an in-line pressure relief valve, a torque limiting device, or a rupture disk. If pump rotation may be reversed during operation, pressure protection must be provided on both sides of pump.

Relief valve adjusting screw caps must always point towards suction side of the pump. If pump rotation is reversed, position of the relief valve must be changed.

Pressure relief valves cannot be used to control pump flow or regulate discharge pressure. For additional information, refer to Viking Pump’s Technical Service

Manual TSM 000 and Engineering Service Bulletin

ESB-31.

● P ump rotation is correct for the desired direction

of flow.

INSTall pressure gauges/sensors next to the pump suction and discharge connections to monitor pressures.

!

THE PUMP must be installed in a matter that allows safe access for routine maintenance and for inspection during operation to check for leakage and monitor pump operation.

WaRNINg

SECTION TSM 142.2

ISSUE E PAGE 2 OF 14

SPECIal INFORMaTION

5.

Pressure relief valves cannot be used to control pump flow or regulate discharge pressure.

DaNgER !

Before opening any Viking pump liquid chamber (pumping chamber, reservoir, relief valve adjusting cap fitting, etc.)

Be sure:

For additional information on pressure relief valves, Refer to Technical Service Manual TSM000 and Engineering

Service Bulletin ESB-31.

1. That any pressure in the chamber has been completely vented through the suction or discharge lines or other appropriate openings or connections.

SPECIAL MECHANICAL SEALS:

Extra care should be taken in repair of these pumps. Be sure to read and follow all special instructions supplied with your pump.

2. That the driving means (motor, turbine, engine, etc.) has been “locked out” or made non-operational so that it cannot be started while work is being done on pump.

MaINTENaNCE

The series 225 and 4225 pumps are designed for long, trouble-free service life under a wide variety of application conditions with a minimum of maintenance. The points listed below will help you get this long service life from your pump.

3. That you know what liquid the pump has been handling and the precautions necessary to safely handle the liquid. Obtain a material safety data sheet (MSDS) for the liquid to be sure these precautions are understood.

LUBRICATION: External lubrication must be applied slowly with a hand gun to all lubrication fittings every 500 hours of operation with multi-purpose grease, NLGI #2. Do not overgrease. Applications involving very high or low temperatures will require other types of lubrication. Refer to Engineering

Service Bulletin ESB-515.

Consult factory with specific lubrication questions.

Failure to follow above listed precautionary measures may result in serious injury or death.

PACKING ADJUSTMENT: New packed pumps generally require some initial packing adjustment to control leakage as OBSOLETED

Refer to instructions under “Disassembly”, page 6, and

“assembly”, page 7, regarding repacking the pump.

JACKETING of the bracket and head provide large chambers

PRODUCT

PRESSURE RELIEF VALVES:

4Q16

After long term

Refer to

Instructions under “Thrust Bearing adjustment”, page

12 , for information regarding this procedure.

CLEANING THE PUMP: It is good practice to keep the pump

1.

Viking pumps are positive displacement pumps and must be provided with some sort of pressure protection.

This may be a relief valve mounted directly on the pump, an inline pressure relief valve, a torque limiting device or a rupture disk.

as clean as possible. This will facilitate inspection, adjustment and repair work and help prevent omission of lubrication of fittings covered or hidden with dirt..

2.

There are relief valve options available on those pump models designed to accept a relief valve. Options may include a return to tank relief valve and a jacketed relief valve. Pumps equipped with a jacketed head plate are generally not available with a relief valve.

STORAGE: If the pump is to be stored or not used for any appreciable length of time, it should be drained, and then a light coat of lubricating and preservative oil should be applied to the internal parts. Lubricate all fittings.

3.

If pump rotation is to be reversed during operation, pressure protection must be provided on both sides of pump.

4.

Relief valve adjusting screw cap must always point towards suction side of pump. If pump rotation is reversed, remove pressure relief valve and turn end for end. Refer to Figures 1 and 2, page 1.

SECTION TSM 142.2

ISSUE E PAGE 3 OF 14

MaINTENaNCE

SUGGESTED REPAIR TOOLS: The following tools must be available to properly repair Series 225 and 4225 pumps.

These tools are in addition to standard mechanics’ tools such as open end wrenches, pliers, screwdrivers, etc. Most of the items can be obtained from an industrial supply house.

1.

Soft Headed hammer

2.

Allen wrenches (some mechanical seals and set collars)

3.

Packing hooks, flexible (packed pumps)

Large for 0.375 inch and up cross section packing

4.

Mechanical seal installation sleeve

5.

Bearing locknut spanner wrench

(Source: #471 J. H. Williams & Co. or equal)

6.

Spanner wrench, adjustable pin type for use on double end caps (Source: #482 J. H. Williams & Co. or equal)

7.

Brass bar

8.

Arbor press

IDlER

ROTOR

JaCKETED aREa

SHaFT

OBSOLETED

PaCKINg glaND

BRaCKET

IDlER

PIN

CaSINg

FIgURE 3

Cutaway View Of Packed Pump Model M225 with Callouts (QS size casing has opposite ports)

JaCKETED

HEaD

SECTION TSM 142.2

ISSUE E PAGE 4 OF 14

PaRT 1 - PaCKED PUMPS

4

5

6

7

ITEM

1

2

3

Locknut

NaME OF PaRT

Lockwasher

End Cap (Outer)

Lip Seal for End Cap

Bearing Spacer Collar (Outer)

Ball Bearing

Bearing Spacer Collar (Inner)

8

9

Ring, Half Round

End Cap (Inner)

10 Packing Gland

11 Packing Gland Nut

12 Packing Gland Capscrew

13 Packing

EXPlODED VIEW FOR MODEl lS225

ITEM NaME OF PaRT

14 Packing Retainer Washer

15 Bracket Bushing

16 Grease Fitting

17 Bracket and Bushing Assembly

18 Capscrew for Bracket

19 Bracket Gasket

20 Casing

21 Nut for Flanges

22 Capscrew for Flanges

ITEM NaME OF PaRT

27 Idler Bushing

28 Head Gasket

29 Idler Pin

30 Head and Idler Pin Assembly

31 Gasket for Jacket Head Plate

32 Jacket Head Plate

33 Capscrew for Head

34 Relief Valve Gasket

35 Capscrew for Relief Valve

23 Pipe Flange Gasket

24 Pipe Plug

25 Rotor and Shaft Assembly

26 Idler and Bushing Assembly

36 Internal Relief Valve OBSOLETED

4

5

6

7

ITEM

1

2

3

Locknut

NaME OF PaRT

Lockwasher

End Cap (Outer)

Lip Seal for End Cap

Bearing Spacer Collar (Outer)

Ball Bearing

End Cap (Inner)

8

9

Packing Gland

Packing Gland Nut

10 Packing Gland Capscrew

11 Packing

EXPlODED VIEW FOR MODElS Q, QS aND M225

ITEM NaME OF PaRT

12 Packing Retainer Washer

13 Bracket Bushing

14 Bracket and Bushing Assembly

15 Grease Fitting

16 Capscrew for Bracket

17 Bracket Gasket

18 Nut for Flanges

19 Stud for Flanges

20 Casing (QS size has opposite ports)

21 Pipe Flange Gasket

22 Pipe Plug

ITEM NaME OF PaRT

23 Rotor and Shaft Assembly

24 Idler and Bushing Assembly

25 Idler Bushing

26 Head Gasket

27 Idler Pin

28 Head and Idler Pin Assembly

29 Stud for Head

30 Nut for Head

31 Relief Valve Gasket

32 Capscrew for Relief Valve

33 Internal Relief Valve

SECTION TSM 142.2

ISSUE E PAGE 5 OF 14

DISaSSEMBlY

DaNgER !

Before opening any Viking pump liquid chamber (pumping chamber, reservoir, relief valve adjusting cap fitting, etc.)

Be sure:

1. That any pressure in the chamber has been completely vented through the suction or discharge lines or other appropriate openings or connections.

2. That the driving means (motor, turbine, engine, etc.) has been “locked out” or made non-operational so that it cannot be started while work is being done on pump.

3. That you know what liquid the pump has been handling and the precautions necessary to safely handle the liquid. Obtain a material safety data sheet (MSDS) for the liquid to be sure these precautions are understood.

Failure to follow above listed precautionary measures may result in serious injury or death.

1.

Mark head and casing before disassembly to make sure they are reassembled properly. Remove the head from the pump.

CAUTION: DO NOT ALLOW THE IDLER TO FALL

FROM THE IDLER PIN.

Tilting the top of the head back as it is removed will prevent this occurrence. Avoid damaging the head gasket if possible. If pump is furnished with a relief valve, it need not be removed from head or disassembled at this point.

Refer to “Pressure Relief Valve Instructions”, page

13.

If the pump has a jacket head plate, this plate will separate from the head when the head is removed from the pump. The gasket for jacket head plate between the head and the jacket head plate should be removed and the gasket surfaces on the above parts cleaned.

Disassembly will probably require replacement of the gasket for jacket head plate between the pump head and jacket head plate.

These gaskets should be carried as spare parts for pumps thus equipped.

2.

Remove the idler and bushing assembly.

3.

Bend up tang of lockwasher and with a spanner wrench remove the locknut and lockwasher from the shaft.

NOTE: A piece of hardwood or brass inserted in casing port and between rotor teeth will prevent the shaft from turning.

NYlON INSERT

PRODUCT

HalF ROUND RINgS gREaSE FITTINg lOCaTION 4Q16

OUTER END CaP lOCKWaSHER lOCKNUT INNER SPaCER COllaR

SHaFT

INNER lIP SEal

Ball BEaRINg

SECTION TSM 142.2

ISSUE E PAGE 6 OF 14

FIgURE 4

OUTER SPaCER COllaR

BRaCKET

OUTER lIP SEal

5.

Tap the shaft forward approximately ½ inch and check for a pair of half circle, round wire rings under the inner bearing spacer collar. See Figure 4.

NOTE: These must be removed before rotor and shaft can be removed from the pump. (These rings are not used in Q, QS and M size pumps.)

6.

Carefully remove rotor and shaft to avoid damage to the bracket bushing.

7.

Remove the packing gland from side of bracket.

8.

Loosen the four setscrews over the inner and outer end caps. Remove both end caps, lip seals and bearing spacer collars. See Figure 4.

The inner cap can be removed through the side opening of the bracket.

9.

Remove the packing and packing retainer washer.

10.

Clean all parts thoroughly and examine for wear and damage. Check lip seals, ball bearings, bushings and idler pin and replace if necessary. Check all other parts for nicks, burrs, excessive wear and replace if necessary.

Wash bearings in clean solvent. Blow out bearings with compressed air. Do not allow bearings to spin; turn them slowly by hand. Spinning bearings will damage race and balls. Make sure bearings are clean, then lubricate with non-detergent SAE 30 weight oil and check for roughness. Roughness can be determined by turning outer race by hand.

If bearings have roughness, bearings will need to be replaced.

11.

Casing can be checked for wear and/or damage while still mounted on bracket.

1.

Install the bracket bushing. (If carbon graphite see

“Installation of Carbon graphite Bushings” page 12 ).

2.

Assemble the rotor and shaft in the bracket. Start the end of the shaft in the bracket bushing and turn from right to left, slowly, pushing the rotor into the casing.

3.

Place the packing retainer washer in the bottom of the packing chamber and pack the pump. It is good practice to install a set of new packing. The pump should be packed with a packing suitable for the liquid being pumped. Install and seat each ring of packing one at a time, staggering the ring joints from one side of the shaft to the other. Lubricate the packing rings with oil, grease or graphite to aid assembly. A length of pipe or tubing will help to install and seat each packing ring.

4.

Install the packing gland, capscrews and nuts. Back the rotor and shaft out of the casing just far enough to insert the packing gland through the side opening of the bracket and over the end of the shaft. This gland cannot be installed with the rotor and shaft in place.

NOTE: Make sure the gland is installed square and nuts tightened evenly. Tighten nuts wrench tight and then back off until gland is slightly loose.

5.

Coat the idler pin with light oil and place the idler and bushing on the idler pin in the head. If replacing a carbon graphite idler bushing see “Installation of Carbon graphite Bushings” page 12.

6.

Put the .010” to .015” thick head gasket on the head and install the head and idler assembly on the pump. The jacket head plate and gasket must be installed at this time (if your pump is equipped with this feature). Tighten the head capscrews.

7.

Slide the inner bearing spacer collar over the shaft with recessed end toward the rotor. Q, QS and M bearing spacer collar is not recessed.

Place the pair of half round rings (not used on Q, QS and M) in the shaft and slide the inner spacer collar over them. See Figure 4.

8.

Press the lip seal (lip toward end of shaft) into the inner end cap and insert the end cap through the shaft end of the bracket. With two fingers turn it clockwise (looking at end of shaft) until it engages the threads. The bosses on the end cap must be toward the rotor. Turn the end cap until it projects slightly into the opening on the side of the bracket.

NOTE: The end cap must be turned so far that the lip of the seal drops off the end of the spacer collar on the shaft or the end cap becomes disengaged with the threads.

See Figure 4.

9.

Pack the ball bearing with multi-purpose grease, place on the shaft and push or drive into place in the bracket.

10.

Install the lip seal (lip toward end of shaft) and bearing spacer in the outer end cap and turn the end cap into the bracket until tight against the bearing. See Figure 4.

11.

Put lockwasher and locknut on shaft. Insert length of hardwood or brass through port opening between rotor teeth to keep shaft from turning. Tighten locknut to 120-

150 ft.– lbs. Torque (LS) or 170-190 ft. – lbs. Torque (Q,

QS, M). Bend one tang of lockwasher into slot of locknut.

If tang does not line up with slot, tighten locknut until it does. Failure to tighten locknut or engage lockwasher tang could result in early bearing failure and cause damage to rest of pump. Remove length of hardwood or brass from port opening.

12.

Adjust the pump end clearance as in “Thrust Bearing adjustment”, page 12.

DaNgER !

Before starting pump, be sure all drive equipment guards are in place.

Failure to properly mount guards may result in serious injury or death.

SECTION TSM 142.2

ISSUE E PAGE 7 OF 14

PaRT 2 - MECHaNICal SEal PUMPS

ITEM

1

2

3

Locknut

NaME OF PaRT

Lockwasher

4

5

6

7

End Cap (Outer)

Lip Seal for End Cap

Bearing Spacer Collar (Outer)

Ball Bearing

8

9

Bearing Spacer Collar (Inner)

Ring, Half Round

End Cap (Inner)

10 Nut for Seal Holder

11 Capscrew for Seal Holder

12 Seal Plate

13 Seal Holder

EXPlODED VIEW FOR MODEl lS4225

ITEM NaME OF PaRT

14 Mechanical Seal

15 Grease Fitting

16 Pipe Plug

17 Bracket and Bushing Assembly

18 Capscrew for Bracket

19 Bracket Bushing

20 Bracket Gasket

21 Casing

ITEM NaME OF PaRT

27 Idler and Bushing Assembly

28 Idler Bushing

29 Head Gasket

30 Idler Pin

31 Head and Idler Pin Assembly

32 Gasket for Jacket Head Plate

33 Jacket Head Plate

34 Capscrew for Head

22 Nut for Flanges

23 Capscrew for Flanges

24 Pipe Flange Gasket

25 Pipe Plug

35 Capscrew for Relief Valve

36 Internal Relief Valve OBSOLETED

26 Rotor and Shaft Assembly

4

5

6

7

ITEM

1

2

3

Locknut

NaME OF PaRT

Lockwasher

End Cap (Outer)

Lip Seal for End Cap

Bearing Spacer Collar

Ball Bearing

End Cap (Inner)

8

9

Nut for Seal Holder

Capscrew for Seal Holder

10 Seal Holder Plate

11 Seal Holder

12 Mechanical Seal

SECTION TSM 142.2

ISSUE E PAGE 8 OF 14

EXPlODED VIEW FOR MODElS Q, QS aND M4225

ITEM

13 Pipe Plug

NaME OF PaRT

14 Grease Fitting

15 Bracket and Bushing Assembly

16 Capscrew for Bracket

17 Bracket Bushing

18 Bracket Gasket

19 Stud for Flanges

20 Nut for Flanges

21 Casing (QS size has opposite ports)

22 Pipe Flange Gasket

23 Pipe Plug

24 Rotor and Shaft Assembly

ITEM NaME OF PaRT

25 Idler and Bushing Assembly

26 Idler Bushing

27 Head Gasket

28 Idler Pin

29 Head and Idler Pin Assembly

30 Stud for Head

31 Nut for Head

32 Relief Valve Gasket

33 Capscrew for Relief Valve

34 Internal Relief Valve

gREaSE FITTINg

DISaSSEMBlY

Before opening any Viking pump liquid chamber (pumping chamber, reservoir, relief valve adjusting cap fitting, etc.)

Be sure:

NYlON INSERT

DaNgER !

INNER

END CaP

HalF

ROUND

RINgS

INNER SPaCER

COllaR

SETSCREWS

OUTER END CaP lOCKWaSHER lOCKNUT

1. That any pressure in the chamber has been completely vented through the suction or discharge lines or other appropriate openings or connections.

2. That the driving means (motor, turbine, engine, etc.) has been “locked out” or made non-operational so that it cannot be started while work is being done on pump.

INNER lIP SEal

Ball BEaRINg

OUTER

SPaCER

COllaR

OUTER lIP

BRaCKET

SEal

3. That you know what liquid the pump has been handling and the precautions necessary to safely handle the liquid. Obtain a material safety data sheet (MSDS) for the liquid to be sure these precautions are understood.

Failure to follow above listed precautionary measures may result in serious injury or death.

4.

STaNDaRD MECHaNICal SEal (Type 9, PTFE is standard). If the mechanical seal fails it can be replaced with a new one. There are two basic parts to the mechanical seal, the rotary member and the stationary seat. See Figure 8, page 11.

To remove the mechanical seal loosen the setscrews around the outside of the OBSOLETED from the shaft end). See Figure 8, page 11.

Rotate the rotor shaft so all setscrews come into view (three on Q,

QS & M, four on LS). Remove the nuts holding the seal holder plate. Remove the seal holder and plate.

1. Mark head and casing before disassembly to make sure they are reassembled properly. Remove the head from PRODUCT

Tilting the top of the head back as it is removed will prevent the idler from falling. Avoid damaging the head gasket if possible. If pump is furnished with a relief valve it need not be removed from the head or disassembled at this point (see page 13 for “Pressure Relief Valve

Instructions”).

If the pump has a jacket head plate, this plate will separate from the head when the head is removed. The gasket for jacket head plate between the head and the jacket head plate should be removed and the gasket surfaces on the above parts cleaned.

Disassembly will probably require replacement of the gasket for jacket head plate between the pump head and jacket head plate. These gaskets should be carried as spare parts for pumps thus equipped.

2.

Remove the idler and bushing assembly.

3.

Bend up tang of lockwasher and with a spanner wrench remove the locknut and lockwasher from the shaft.

NOTE: A piece of hard wood or brass inserted in the casing port and between the rotor teeth will prevent the shaft from turning.

FIgURE 5

OPTIONal MECHaNICal SEal (Type 1 or equivalent single synthetic rubber bellows style). It uses a set collar behind the seal spring. See Figure 7, page 11.

Two setscrews must be loosened before shaft can be removed. Access to the collar setscrews is through the seal access hole on the right hand side of the mounting bracket (viewed from the shaft end).

5.

Tap the shaft toward head approximately ½ inch and check for a pair of half circle, round wire rings, under the inner bearing spacer collar. NOTE: These half rings must be removed before the rotor and shaft can be removed from the pump (these rings are not used in the

Q, QS and M size pumps).

6.

Carefully remove the rotor and shaft. As the shaft is being removed decreasing shaft diameters tend to allow the shaft to drop onto the bracket bushing. To avoid damaging the bracket bushing, support the rotor and do not allow either end of the shaft to tilt downward. NOTE:

Considerable force may be required to remove the rotor and shaft from the pump. Be careful seal parts are not damaged as the rotor and shaft is removed.

7. The seal seat and rotary member of the seal can now be removed from the side opening of bracket.

SECTION TSM 142.2

ISSUE E PAGE 9 OF 14

8.

Loosen the four setscrews over the outer and inner end caps. Remove both end caps, ball bearing and bearing spacer collars. See Figure 5, page 9. NOTE: The inner end cap can be removed through the side openings in the bracket.

9.

Clean all parts thoroughly and examine for wear or damage. Check lip seals, ball bearing, bushings, and mechanical seal and replace as necessary. Check all other parts for nicks, burrs, excessive wear and replace if necessary. NOTE: Be sure shaft is free from burrs and foreign particles that might damage the bracket bushing. Scratches on the shaft in the seal area will provide leakage paths under the mechanical seal.

Move the rotary member so the setscrews are directly below the seal access holes on the left side of the bracket

(viewed from the shaft end) - see Figure 8.

Tighten all setscrews securely to the shaft. Flush the sealing faces of both the rotary member and seal seat with oil and install the seal seat and a seat gasket over the end of the shaft against the machined bracket face. Assemble the other seal seat gasket, seal holder, seal holder plate, capscrews and nuts and tighten securely. Remove the tapered installation sleeve.

OPTIONal MECHaNICal SEal (See Figure 7)

Install the seal set collar - examine the set collar to be sure that there are no burrs or scratches and that the setscrews are withdrawn so that the shaft will 10.

Check casing for wear or damage while mounted to the bracket.

Clean the rotor shaft and bracket seal housing bore.

Make sure they are free of dirt, grit and scratches. Gently radius the leading edge of the shaft diameter over which the seal must be placed. A tapered sleeve is available, at extra cost, for the “Q, QS and M” pumps from Viking

Pump Division for installation of the mechanical seal on the shaft as in Figure 6. The “LS” pump shaft is tapered and an installation sleeve is not available.

Not be scratched when the set collar is installed. Place the set collar onto the shaft, push it into the seal chamber until the centerline of the setscrews coincides with the centerline of the tapped seal access holes on the right side of the bracket (viewed from the shaft end). Tighten all the setscrews in the set collar securely.

aSSEMBlY

1.

Install the bracket bushing (if carbon graphite, see

“Installation of Carbon graphite Bushings” on page

12 ).

2.

Assemble the rotor and shaft in the bracket. Start the end of the shaft in the bracket bushing and turn from right to left slowly, pushing the rotor into the casing.

3.

Coat the idler pin, in the head, with light oil and place the idler and bushing on the idler pin. If replacing a carbon graphite idler bushing see “Installation of Carbon graphite Bushings” on page 12 .

4.

Put the head gasket on the head and install the head and idler assembly on the pump. Tighten the head capscrews or nuts.

5.

STANDARD MECHANICAL SEAL (PTFE - see Figure

8 ). The seal is simple to install and good performance will result if care is taken during installation.

Install the rotating member of the seal - Slide the spring over the shaft into the seal chamber and onto the set collar pilot. Center the spring adapter (on Q, QS & M models only) against the back of the metal retainer so that the spring will push against the adapter and not work itself over the back of the mechanical seal. Place the tapered sleeve on the shaft as in Figure 9.

Apply a liberal coating of SAE-30 lube oil to the large diameter OBSOLETED centered against the adapter.

Install the Stationary Seal Seat - Lubricate the outside diameter of the mechanical seal O-Ring seat gasket and flush the lapped face with lube oil. Press the stationary seat into the bore until the back, unlapped face, is just inside the bore. Position the stationary seat by installing the seal holder and secure the seal holder to the machined face of the bracket with the seal holder plate.

Tighten the nuts securing the seal holder plate evenly so that the seal holder will not be distorted.

Remove the tapered installation sleeve.

COaT SHaFT aND TaPERED SlEEVE

WITH lIgHT OIl BEFORE aSSEMBlY

TaPERED SlEEVE

Coat the tapered sleeve and the inside of the rotary member with a generous quantity of SAE 30 nondetergent oil. Grease is not recommended. Start the rotary member on the shaft and over the tapered sleeve.

CaUTION: Some seals may be equipped with installation clips. These must be removed after seal is placed on the proper diameter portion of the shaft.

MECHaNICal SEal

(ROTaRY MEMBER)

FIgURE 6

SECTION TSM 142.2

ISSUE E PAGE 10 OF 14

SEal aCCESS HOlE (FOR SETSCREWS)

SPRINg aDaPTER

MECHaNICal SEal (ROTaRY MEMBER)

SEal SEaT gaSKET

SEal HOlDER

RIgHT SIDE

OF PUMP

SEal

HOlDER

PlaTE

SET COllaR SEal

SEaT

10.

Put lockwasher and locknut on shaft. Insert length of hardwood or brass through port opening between rotor teeth to keep shaft from turning. Tighten locknut to 120-

150 ft.– lbs. Torque (LS) or 170-190 ft. – lbs. Torque (Q,

QS, M). Bend one tang of lockwasher into slot of locknut.

If tang does not line up with slot, tighten locknut until it does. Failure to tighten locknut or engage lockwasher tang could result in early bearing failure and cause damage to rest of pump. Remove length of hardwood or brass from port opening.

SPRINg

MECHaNICal SEal

(ROTaRY MEMBER)

FIgURE 7 - OPTIONal MECHaNICal SEal

SEal SEaT gaSKET lEFT SIDE

OF PUMP

SEal

HOlDER

PlaTE

TaPERED SlEEVE

COaT WITH lIgHT OIl BEFORE aSSEMBlY

FIgURE 9 gREaSE FITTINg

INNER

END CaP

NYlON INSET

6.

MECHaNICal SEal (ROTaRY MEMBER) 4Q16 used on Q and M size pumps).

SEal HOlDER

SEal SEaT

SEal aCCESS HOlE (FOR SETSCREWS) recessed end toward rotor. NOTE: The pair of half round rings must be inserted in the groove in the shaft and then slide the spacer collar over them. See Figure 10 (not

HalF

ROUND

RINgS

INNER SPaCER

COllaR

INNER lIP SEal

Ball BEaRINg

7. Press the lip seal (lip toward end of shaft) into the inner end cap and insert the end cap through the shaft end of the bracket. With two fingers turn it clockwise (looking at end of shaft) until it engages the threads. The bosses on the end cap must be toward the rotor. Turn the end cap until it projects slightly into the opening on the side of the bracket. NOTE: The end cap must not be turned so far that the lip of the lip seal drops off the end of the spacer collar on the shaft or the end cap becomes disengaged with the threads. See Figure 10.

FIgURE 10

lOCKWaSHER lOCKNUT

11. Adjust the pump end clearance as in “Thrust Bearing adjustment” (see Page 11).

DaNgER !

OUTER

SPaCER

COllaR

OUTER lIP

SEal

BRaCKET

8.

Pack the ball bearing with multi-purpose grease, place on the shaft and push or gently drive into place in the bracket.

Before starting pump, be sure all drive equipment guards are in place.

9.

Install the lip seal (lip toward end of shaft) and bearing spacer in the outer end cap and turn the end cap into the bracket until tight against the bearing. See Figure 10.

Failure to properly mount guards may result in serious injury or death.

SECTION TSM 142.2

ISSUE E PAGE 11 OF 14

THRUST BEaRINg aDJUSTMENT

See Figure 10, page 11.

INSTallaTION OF CaRBON gRaPHITE BUSHINgS

1.

Loosen the two setscrews over each of the outer and inner end caps.

2.

Turn the inner end cap clockwise (viewed from shaft end) until it projects slightly into the opening on the side of the bracket exposing approx. three threads.

When installing a new carbon graphite idler or bracket bushing, extreme care should be taken to prevent breaking, as it is a brittle material and easily cracked. If cracked the bushing will quickly disintegrate. NOTE: Using a lubricant and adding a chamfer on the bushing and the mating part will help in the installation of carbon graphite bushings.

3.

Turn the outer end cap clockwise until the rotor is tight against the head and the rotor shaft cannot be turned.

4. Make a reference mark on the bracket end, opposite a notch on the outer end cap. Back off the outer end cap the required number of notches as shown in the

Total End Clearance Chart, see Figure 11.

Each notch represents .002” end clearance.

5.

High viscosity liquids require additional end clearances.

The amount of extra end clearance depends on the viscosity of the liquid pumped. For specific recommendations consult the factory.

6.

Tighten the inner end cap with a spanner wrench. Tap the spanner wrench lightly but DO NOT OVER TIgHTEN as it will damage the threads.

An arbor press should always be used for installing carbon graphite bushings. Be sure bushing is started straight and

DO NO STOP pressing operation until bushing is in proper position. Starting and stopping will invariably result in a cracked bushing.

Carbon graphite bushings with extra interference fits are frequently furnished for high temperature operation. These bushings must be installed by a shrink fit. Heat the bracket or idler to 750ºF (400ºC) and install cool bushings with an arbor press. (If facilities are not available for this temperature, it is possible to install with 450ºF (232ºC) temperature.

However the lower the temperature the greater the possibility of cracking the bushing.) Check for additional information on high temperature applications see Engineering Service

Bulletin ESB-3.

7. Tighten the set screws that hold the inner and outer end caps to prevent their turning in the bracket.

8.

Check the rotor to determine if it turns freely; if it does not, add more end clearance.

TOTal END ClEaRaNCE CHaRT

OBSOLETED

PUMP

SIzE

TURN OUTER END CaP

COUNTER-ClOCKWISE

NO. OF NOTCHES

Check bushing for cracks after installation. Coat surface of the bushing with amyl acetate (banana oil). Let it evaporate, and any cracks will be visible wet streaks. If cracks appear, the bushing should be replaced. CaUTION: Amyl acetate is a flammable solvent and should be used with care.

LS

Q, QS AND M

5

7.5

TOTal

END

ClEaRaNCE*

.010

.015

4Q16

* Total End Clearance includes extra clearance for temperatures of 450°F (232°C).

FIgURE 11

SECTION TSM 142.2

ISSUE E PAGE 12 OF 14

SaFETY RElIEF ValVE

INSTRUCTIONS

DISaSSEMBlY

DaNgER !

Before opening any Viking pump liquid chamber (pumping chamber, reservoir, relief valve adjusting cap fitting, etc.)

Be sure:

1. That any pressure in the chamber has been completely vented through the suction or discharge lines or other appropriate openings or connections.

2. That the driving means (motor, turbine, engine, etc.) has been “locked out” or made non-operational so that it cannot be started while work is being done on pump.

3. That you know what liquid the pump has been handling and the precautions necessary to safely handle the liquid. Obtain a material safety data sheet (MSDS) for the liquid to be sure these precautions are understood.

Failure to follow above listed precautionary measures may result in serious injury or death.

PRODUCT

1.

Remove valve cap.

2.

Measure and record the length of extension of the adjusting screw. Refer to “a” on Figures 12 and 13.

3.

Loosen the locknut and back out adjusting screw until spring pressure is released.

4.

Remove bonnet, spring guide, spring and poppet from valve body. Clean and inspect all parts for wear or damage and replace as necessary.

FIgURE 12

ValVE - lS, Q, QS aND M SIzES lIST OF PaRTS

6. Valve Body

2. Adjusting Screw

3. Lock Nut

7. Valve Spring

8. Poppet

4. Spring Guide

5. Bonnet

9. Cap Gasket

10. Bonnet Gasket

SECTION TSM 142.2

ISSUE E PAGE 13 OF 14

TECHNICAL SERVICE MANUAL

HEaVY-DUTY BRaCKET MOUNTED PUMPS

SERIES 225 aND 4225

SIzES lS, Q, QS, M

SECTION TSM 142.2

PagE

ISSUE

14 OF 14

E

aSSEMBlY

Reverse the procedure outlined under disassembly.

If valve is removed for repairs, be sure to replace in same position. The valve cap should point towards the suction port.

DaNgER !

Before starting pump, be sure all drive equipment guards are in place.

WARRANTY

Viking warrants all products manufactured by it to be free from defects in workmanship or material for a period of one (1) year from date of startup, provided that in no event shall this warranty extend more than eighteen (18) months from the date of shipment from

Viking. The warranty period for Universal Seal series pumps ONLY (Universal Seal models listed below) is three (3) years from date of startup, provided that in no event shall this warranty extend more than forty-two

(42) months from the date of shipment from Viking.

Failure to properly mount guards may result in serious injury or death.

PRESSURE aDJUSTMENT

If the pressure setting of the safety relief valve is to be changed from that which the factory has set, the following instructions should be carefully followed: Remove the valve cap which covers the adjusting screw, and loosen the lock nut which locks the adjusting screw so pressure setting will not change during operation of pump. A pressure gauge somewhere in the discharge line must be used for actual adjustment operation. The adjusting screw should be turned in for increasing the pressure or turned out for decreasing the pressure. With the discharge line closed at a point beyond the pressure gauge, the gauge will show the maximum pressure the valve will allow while pump is in operation.

IMPORTaNT

UNDER NO CIRCUMSTANCES SHALL VIKING BE

LIABLE UNDER THIS WARRANTY OR OTHERWISE

FOR SPECIAL, INCIDENTAL, INDIRECT,

CONSEQUENTIAL OR PUNITIVE DAMAGES OF ANY OBSOLETED

DAMAGE TO REPUTATION, LOSS OF PROPERTY,

LOSS OF INFORMATION OR DATA, LOSS OF

PRODUCTION, DOWNTIME, OR INCREASED

COSTS, IN CONNECTION WITH ANY PRODUCT,

EVEN IF VIKING HAS BEEN ADVISED OR PLACED

ON NOTICE OF THE POSSIBILITY OF SUCH

DAMAGES AND NOTWITHSTANDING THE FAILURE

OF ANY ESSENTIAL PURPOSE OF ANY PRODUCT.

THIS WARRANTY IS AND SHALL BE VIKING’S SOLE

AND EXCLUSIVE WARRANTY AND SHALL BE IN

LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO, ALL WARRANTIES OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE AND

NON-INFRINGEMENT ALL OF WHICH OTHER

WARRANTIES ARE EXPRESSLY EXCLUDED.

In ordering parts for safety relief valve, always be sure to give model number and serial number of pump as it appears on nameplate and the name of the part wanted. When ordering springs, be sure also to give pressure setting desired.

See complete warranty at www.vikingpump.com.

VIKING PUMP, INC.

A Unit of IDEX Corporation

Cedar Falls, IA 50613 USA

© 3/2013 Viking Pump Inc.

All rights reserved

advertisement

Related manuals

Download PDF

advertisement