Honda 08B15-SDN-100 Installation Instructions Manual

PDF Download

Document

INSTALLATION

INSTRUCTIONS

Accessory

XM RADIO SYSTEM

PARTS LIST

XM Radio Attachment Kit (sold separately):

P/N 08B15-SDN-100

Application

2005 ACCORD 2-DOOR

(LX/EX L4, LX V6)

Double-sided adhesive tape

Display unit pocket

DIN cable

XM radio harness

Clip nut

3 Self-tapping screws

Publications No.

AII 27573

Issue Date

OCT 2004

Fastener

Upper bracket

Lower bracket

Ground bolt (gold)

6 Washer-screws, 4 x 8 mm

Modulator bracket

2 Washer-screws, 5 x 10 mm

2 Flange nuts, 5 mm

3 Off-set wire ties with clip

2 Washer-bolts, 6 x 12 mm

4 Flange nuts, 4 mm

30 Wire ties

Connector clip

8 Wire tie with clips (two not used)

AII 27573 (0410) 08B15-SDA-1001-91

1 of 22

5 Cushion tapes

5 EPT sealers

Fuse label

Mini fuse, 5A

Antenna Kit (sold separately):

P/N 08A15-1E1-100

Antenna cable

Base Kit (sold separately):

P/N 08A15-1E1- 000

Display unit

FM modulator unit

Receiver unit

Owner's Manual

2 of 22

Audio Attachment Kit (sold separately):

P/N 08B06-SDA-100

(Not required if already equipped with a player.)

Left player bracket

Right player bracket

Left player subbracket

Right player subbracket

Player base-bracket

Player panel

Pocket

BUS cable

(Used on vehicles without

Navigation)

2 Latches

8 Flange nuts, 6 mm

2 Grommet screws

2 Wire ties

3 EPT sealers

2 Self-tapping screws, 4 x 12 mm

TOOL AND SUPPLIES REQUIRED

Phillips screwdriver

Stubby Phillips screwdriver

Flat-tip screwdriver

Isopropyl alcohol

Shop towel

Tape measure

Utility knife

Hook tool

Ratchet wrench

8 mm and 10 mm Sockets

Felt-tip pen

Scissors

Push pin

Vinyl tape

Drill

3 mm and 10 mm Drill bits

Touch-up paint

Eye protection (face shield, safety goggles, etc.)

Masking tape

Illustration of the XM Radio System Installed in the

Vehicle

DISPLAY MODULE

DIN CABLE

RECEIVER

UNIT

ANTENNA

2N28160M

FM MODULATOR

UNIT

XM RADIO

HARNESS

VEHICLE

ANTENNA

CABLE FM MODULATOR

UNIT

DISPLAY

MODULE

FUSE BOX

6-PIN

CONNECTOR

XM RADIO

HARNESS

ANTENNA

DIN CABLE

RECEIVER UNIT

2N28010M

AII 27573 (0410)

3 of 22

INSTALLATION

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

Make sure you have the anti-theft code for the radio, then write down the radio station presets.

Disconnect the negative cable from the battery.

Remove the trim ring.

M/T Vehicle:

• Squeeze the plastic clip, and pull down on the shift boot. Remove the shift knob by turning it counterclockwise.

SHIFT KNOB

(Turn counterclockwise.)

• Gently pry up on the trim ring to release the six clips.

• Unplug the two seat heater connectors

(if equipped), and remove the trim ring.

RETAINING

CLIPS (4)

RETAINING

CLIPS (2)

PLASTIC

CLIP

SHIFT

BOOT

2206032K

TRIM

RING

SEAT HEATER

CONNECTOR

(if equipped)

2206041K

A/T Vehicle:

• Gently pry on the trim ring to release the six clips.

• Unplug the two seat heater connectors

(if equipped), and remove the trim ring.

RETAINING

CLIPS (4)

RETAINING

CLIPS (2)

4 of 22

AII 27573 (0410)

TRIM RING

SEAT HEATER

CONNECTOR

(if equipped)

2206112K

Remove the center holder.

• Open the lid, and remove the coin pocket.

• Remove the two self-tapping screws.

• Gently pull out the dashboard center holder to release the two retaining clips, unplug the vehicle connector, and remove the center holder.

With Coin Pocket:

COIN

POCKET

LID

SELF-TAPPING

SCREW

CENTER HOLDER

If the vehicle is equipped with a cassette/MP3/CD player, go to step 13; otherwise, go to step 5.

Remove the pocket:

• Apply masking tape to the edge of the center panel.

• Remove the two self-tapping screws.

• Push in on the bottom of the lid, then pull out on the top by inserting the end of a hook tool between the pocket and center panel. Pull the pocket toward you to release the two retaining clips.

• Set the pocket aside; it will not be reused.

MASKING

TAPE

HOOK

TOOL

RETAINING

CLIPS (2)

POCKET

LID

RETAINING

CLIPS (2) VEHICLE

CONNECTOR

2206061K

With Optional Ashtray:

• Open the lid, and remove the ashtray.

• Remove the two self-tapping screws.

• Gently pull out on the two retaining clips, unplug the cigarette lighter harness connector, vehicle connector, illumination bulb, and remove the center holder.

ASHTRAY

SELF-TAPPING

SCREW

CENTER

HOLDER

ILLUMINATION

BULB

POCKET

SELF-TAPPING

SCREW

2206073K

Remove the right and left inner covers (one hook and one clip for each cover). Set the inner covers aside; they will not be reused.

LEFT INNER

COVER

CLIP

RETAINING

CLIPS (2)

VEHICLE

CONNECTOR

2730010K

CIGARETTE

LIGHTER

HARNESS

CONNECTOR

AII 27573 (0410)

HOOK

RIGHT INNER

COVER

POCKET

OPENING

2226010K

5 of 22

Remove the vehicle harness clip from the vehicle frame, and move the clip out of the way.

PLAYER BASE-

BRACKET

VEHICLE

FRAME

VEHICLE

HARNESS

CLIP

(Remove.)

10. Get the pocket from the audio attachment kit.

Using a utility knife, cut the two lugs off of the pocket.

LUG

(Cut off.)

6 mm

FLANGE

NUT

6 mm

FLANGE

NUT

VEHICLE

FRAME

2306011T

VEHICLE HARNESS CLIP

(Insert into the hole of the player base-bracket.)

Insert the studs from the player base-bracket into the holes in the vehicle frame from the back.

Install the two 6 mm flange nuts while holding the bracket firmly against the vehicle frame. Insert the vehicle harness clip (removed in step 7) into the hole in the player base-bracket.

Insert the studs of the left and right player subbrackets into the holes in the vehicle frame, and install one 6 mm flange nut on the end of each stud while pushing each subbracket upward.

6 mm FLANGE NUT

6 of 22

VEHICLE

FRAME

LEFT PLAYER

SUBBRACKET

RIGHT PLAYER

SUBBRACKET

POCKET

LUG

2529041T

11. Install one latch onto the left and right player brackets. Slide the clip nut onto the display module pocket flange.

1 mm

LATCH

DISPLAY MODULE

POCKET FLANGE

LATCH

CLIP NUT

VEHICLE

FRAME

2306021T

DISPLAY

MODULE

POCKET

SELF-

TAPPING

SCREW (2)

(supplied with audio attachment kit)

LEFT

PLAYER

BRACKET

POCKET

RIGHT

PLAYER

BRACKET

SELF-TAPPING

SCREWS (3)

(supplied with

XM radio attachment kit)

2N28071M

BRACKET

HOLE

SCREW

POSITION

12 Set the display module pocket on the pocket with the cut out facing up. Position the left and right player brackets on the display module pocket and pocket, and install five self-tapping screws.

If the vehicle is not equipped with a cassette/MP3/

CD player, go to step 18; otherwise, go to step 13.

13. Remove the player panel by removing the two self-tapping screws and two clips.

CLIP

PLAYER PANEL

15. Remove the left and right audio brackets (two washer-screws and one self-tapping screw for each bracket). Separate the player and pocket.

Set the pocket aside; it will not be reused.

WASHER-

SCREW

LEFT AUDIO

BRACKET

PLAYER

(Cassette/MP3/CD)

RIGHT AUDIO

BRACKET

WASHER-

SCREW

SELF-TAPPING

SCREW

2306141T

14. Remove the player/pocket assembly. Unscrew the four flange nuts, and pull the assembly out toward you. Unplug the audio subharness cable connector.

VEHICLE

CONNECTOR

(without navigation system)

VEHICLE CONNECTOR

(with navigation system)

AUDIO

SUBHARNESS

CONNECTOR

(with navigation system)

AUDIO

SUBHARNESS

CONNECTOR

(without navigation system)

LEFT PLAYER

BRACKET

LEFT PLAYER

SUBBRACKET

SELF-

TAPPING

SCREW POCKET

(Do not reuse.)

SELF-TAPPING

2N28080M

SCREW

16. Slide the clip nut (supplied) onto the display module flange.

DISPLAY

MODULE

POCKET

CLIP NUT

WASHER-

SCREW

(supplied with

Audio

Attachment kit)

PLAYER

(Cassette/MP3/CD)

WASHER-

SCREW

(supplied with Audio

Attachment kit)

6 mm

FLANGE

NUT

RIGHT

PLAYER

BRACKET

PLAYER BASE-

BRACKET

RIGHT PLAYER

SUBBRACKET

SELF-

TAPPING

SCREW

LEFT

PLAYER

BRACKET

HOLE

SCREW

POSITION

DISPLAY

MODULE

RIGHT

PLAYER

BRACKET

SELF-TAPPING

SCREWS (2)

(supplied with

XM radio attachment kit)

17. Set the player on the display module pocket.

Position the left and right player brackets on the display module pocket and player, and reinstall the four washer-screws. Install the three self-tapping screws to secure the display module pocket.

AII 27573 (0410)

7 of 22

Installing the Display Unit

18. Attach the display unit to the display unit pocket:

• Using isopropyl alcohol on a shop towel, clean the center on the back of the display unit where the adhesive backing will attach.

• Remove the backing from one side of the double-sided adhesive tape, and attach it to the display unit.

• Remove the remaining backing from the double-sided adhesive tape. Route the display unit cable through the hole of the display unit pocket, and attach the display unit to the display module pocket.

DOUBLE-SIDED

ADHESIVE TAPE

DISPLAY UNIT

BACKING

Without Player:

Clean with isopropyl alcohol.

DISPLAY

UNIT

POCKET

DISPLAY UNIT CABLE

With Player:

POCKET

PLAYER

DISPLAY

UNIT

CABLE

DISPLAY

UNIT

POCKET

2N28110M

If the vehicle is not equipped with a cassette/MP3/

CD player, go to step 20; otherwise, go to step 19.

19. Plug the audio subharness cable into the player.

Cassette Player

Make loops in the audio subharness cable, and secure it with one wire tie, so that the distance between the ends of the cable connector is

200 mm. Plug the audio subharness cable connector into the cassette player connector.

CASSETTE

PLAYER

WIRE TIE

(supplied with audio attachment kit)

AUDIO

SUBHARNESS

CABLE

AUDIO

SUBHARNESS

CABLE

CONNECTOR

AUDIO

SUBHARNESS

CABLE

CONNECTOR

200 mm

2306051T

Multimedia Player

Make loops in the audio subharness cable, and secure it with one wire tie so that the distance between the ends of the cable connectors is

200 mm. Plug the audio subharness cable connector into the multimedia player connector.

MULTIMEDIA

PLAYER

AUDIO

SUBHARNESS

CABLE

CONNECTOR

BUS CABLE

WIRE TIE

(supplied with audio attachment kit)

AUDIO

SUBHARNESS

CABLE

CONNECTOR

200 mm

2306061T

8 of 22

In-Dash CD Player

• Make loops in the audio subharness cable, and secure it with one wire tie so that the distance between the ends of the cable connectors is

180 mm. Plug the audio subharness cable connector into the connector from the in-dash

CD player.

• After connecting, secure the connectors to the rear of the in-dash player with one wire tie from the in-dash CD player kit.

IN-DASH CD

PLAYER

WIRE TIE

(supplied with audio attachment kit)

21. Remove the rear console.

• Open the lid, and remove the rear console mat from inside the rear console.

• Remove the two screws and the four selftapping screws, and unplug the connector and harness clip (if equipped).

• If equipped with a console-mounted CD changer, remove the changer from the rear console.

REAR CONSOLE MAT

SELF-TAPPING

SCREWS (4)

SCREWS (2)

AUDIO

SUBHARNESS

CABLE

CONNECTOR

180 mm

WIRE TIE

(supplied with audio attachment kit)

AUDIO

SUBHARNESS

CABLE

AUDIO

SUBHARNESS

CABLE

Routing the XM Radio Harness

20. Remove the beverage holder (pull up to release the six retaining clips).

CONNECTOR

(if equipped)

HARNESS CLIP

(if equipped)

2206090K

RETAINING

CLIPS (4)

RETAINING

CLIPS (2)

BEVERAGE

HOLDER

2206050K

AII 27573 (0410)

9 of 22

22. Remove the driver’s dashboard lower cover:

• Remove the self-tapping screw.

• Release the four clips on the left side first by pulling out on the driver's dashboard lower cover.

• After releasing the four clips, insert a flat-tip screwdriver behind the clip at the dashboard frame. Gently twist the screwdriver to release the clip.

• Release the two clips on the right side. Unplug the vehicle connector, then remove the lower cover.

CONNECTOR DASHBOARD

LOWER COVER

24. Remove the self-tapping screw and the clip that secure the left front console cover. Take care not to damage the clip, and remove the console cover.

SELF-TAPPING

SCREW

CLIP

LEFT FRONT

CONSOLE COVER

PUSH REMOVE

2206131K

SELF-

TAPPING

SCREW

RETAINING

CLIPS (7)

2206120K

23. If equipped, remove the driver’s dashboard under cover (release the three retaining clips, one pin, and one holder).

HOLDER

10 of 22

RETAINING

CLIPS (3)

DRIVER’S DASHBOARD

UNDER COVER

PIN

2205020T

25. On the driver's side of the vehicle, locate the 6-pin connector on the fuse box. Plug the XM radio harness 6-pin connector into the fuse box 6-pin connector.

NOTE: If the 6-pin connector is already being used by another accessory, locate the 6-pin connector taped to the XM radio harness. Remove the dummy connector from the harness, and plug the other accessory's harness 6-pin connector into the

XM radio harness.

27. Install the XM radio harness fuse cases and the

6-pin dummy connector to the fuse box case.

Fuse case position

FUSE

CASES

VEHICLE

HARNESS

(Do not secure to the yellow

SRS harness.)

WIRE TIE

XM RADIO

HARNESS

OTHER

ACCESSORY

6-PIN

HARNESS

XM RADIO HARNESS

6-PIN CONNECTOR

DUMMY

CONNECTOR

(Discard.)

2524060M

6-PIN

CONNECTOR

FUSE BOX

6-PIN

CONNECTOR

FUSE

CASES

2N28020M

XM RADIO HARNESS

6-PIN CONNECTOR

WITH DUMMY

CONNECTOR

28. Secure the XM radio harness to the vehicle harness with one wire tie. Do not secure it to the yellow SRS harness.

29. Route the XM radio harness under the steering shaft and toward the center console.

VEHICLE HARNESS

FUSE

LABEL

XM RADIO

HARNESS

CLIP

2524051M

FUSE LABEL

WIRE TIES (3)

CENTER

CONSOLE

XM RADIO

HARNESS

3121030M

Use these labels.

26. Attach the fuse labels to the fuse cases on the

XM radio harness.

2N28030M

29. Loosely attach the XM radio harness to the vehicle harness with three wire ties.

AII 27573 (0410)

11 of 22

30. Inside the center console, locate the welded nut on the vehicle stay. Attach the XM radio harness ground terminal to the welded nut with the ground bolt supplied.

GROUND

BOLT

WIRE TIE

VEHICLE

HARNESS

33. Attach the modulator bracket to the player basebracket with two 5 x 10 mm washers and two

5 mm flange nuts.

CUSHION TAPE

MODULATOR

BRACKET

HALF

CUSHION

TAPE

Clean with isopropyl alcohol.

Cut

5 mm

FLANGE

NUT

PLAYER

BASE-

BRACKET

GROUND

TERMINAL

3-PIN

CONNECTOR

XM RADIO

HARNESS

3606010M

31. Secure the XM radio harness to the vehicle harness with one wire tie. Route the 3-pin connector, and the remaining end of the XM radio harness toward the rear of the vehicle; they will be routed later.

FM Modulator Unit Installation

32. To protect the center panel, attach masking tape to the center panel in the area shown.

CENTER

PANEL

MASKING

TAPE

HALF

CUSHION TAPE

5 x 10 mm

WASHER-

SCREW

3605060M

34. Using scissors, cut one cushion tape in half.

Using isopropyl alcohol, clean the bonding surfaces of the brackets, and attach the half cushion tapes to the brackets in the area shown.

35. Install the FM modulator unit to the modulator bracket with two 4 x 8 mm washer-screws. Attach the connector clip from the FM modular unit harness into the hole in the player base-bracket.

4 x 8 mm

WASHER-

SCREW

FM MODULATOR

BRACKET

MODULATOR

BRACKET

4 x 8 mm

WASHER-

SCREW

PLAYER BASE

BRACKET

HOLE OF THE

MODULATOR

BRACKET

2506010T

12 of 22

AII 27573 (0410)

3605071M

CONNECTOR CLIP

36. Insert the studs from the player base-bracket into the holes in the vehicle frame from the back, then install the two 6 mm flange nuts while holding the bracket firmly against the vehicle frame.

PLAYER

BASE-BRACKET

39. Unplug the vehicle antenna cable, and plug it into the FM modulator unit antenna cable. Plug the other end of the FM module antenna jack into the vehicle antenna cable.

WIRE TIE

VEHICLE

HARNESS

WIRE TIE

VEHICLE

HARNESS

WIRE

TIE

EXCESS

ANTENNA

CABLE

EPT

SEALER

6 mm FLANGE

NUTS (2)

VEHICLE

FRAME

3605081M

37. Connect the XM radio harness 3-pin connector to the FM modulator unit harness 3-pin connector.

38. Get a DIN cable from the XM radio attachment.

Plug the 90° end of the DIN cable connector into the FM modulator unit, then route the DIN cable rearward along the XM radio harness .

XM RADIO

HARNESS

3-PIN

CONNECTOR

DIN

CABLE

FM MODULATOR

UNIT

3606042M

FM MODULATOR

ANTENNA CABLE

VEHICLE

ANTENNA

CABLE

40. Wrap one EPT sealer around the antenna jack, and secure the antenna cable to the vehicle antenna cable with the one wire tie. Secure both antenna cables to the vehicle harness with one wire tie.

41. Loop the excess antenna cable from the

FM modulator, and secure the excess cable to the vehicle harness with two wire ties.

XM RADIO

HARNESS

FM MODULATOR

UNIT HARNESS

CONNECTOR

3609041M

AII 27573 (0410)

13 of 22

42. Plug the display module cable into the FM modulator unit. Pull the excess length of the cable out from under the display module unit.

45. Loop the excess display module cable along the

DIN cable and the vehicle harness, then secure the display module cable, and the DIN cable with one wire tie with clip. Insert the clip from the wire tie into the modulator bracket hole.

DISPLAY

MODULE UNIT

WIRE TIE

WITH CLIP

MODULATOR

BRACKET HOLE

DISPLAY MODULE

CABLE

XM RADIO

HARNESS

DISPLAY

MODULE

CABLE

(Pull out.)

REAR

3606052M

43. If equipped with a player, plug the BUS cable connector into the vehicle connector.

PLAYER BUS

CABLE

CONNECTOR

(If equipped.)

WIRE TIE

3606061M

DIN CABLE

46. Near the subbracket, secure the XM radio harness to the vehicle harness with one wire tie.

47. Secure the excess length of DIN cable and

XM radio harness to the vehicle harness with two wire ties.

48. If the vehicle is not equipped with a player, attach the two grommet screws to the player panel in the square holes as shown.

PLAYER

PANEL

6 mm FLANGE

NUTS (4)

3618021M

44. Install the display module assembly onto the studs from the left and right player subbrackets, and install the 6 mm flange nuts. Tighten the flange nuts securely.

14 of 22

AII 27573 (0410)

GROMMET SCREW

2306131T

49. Get one EPT sealer. Measure the EPT sealer as shown, and cut it into three pieces.

EPT SEALER

(Cut off the marked area.)

PLAYER

PANEL

52. Inside the passengers' compartment, remove the rear seat cushion by removing the bolt and releasing the two locks (pull the lock out toward you).

BOLT

8 mm

EPT SEALER

2612010T

50. Using isopropyl alcohol on a shop towel, clean the player panel in the area shown. Attach the two cut pieces of the EPT sealer to the player panel, and cut off the excess.

51. Attach the player panel by inserting the clips into the latches, and install two self-tapping screws from the kit, or reinstall the two self-tapping screws you removed in step 13. Remove the masking tape.

REAR SEAT

CUSHION

HOOKS (2)

(Pull down.)

2527020T

LOCKS (2)

LEVERS (2)

(Pull out.)

53. Inside the trunk, fold the right and left seatbacks down by pulling the strap and pushing forward on the seat.

STRAP

LEFT REAR

SEAT CUSHION

CLIP

LATCH

PLAYER

PANEL

SELF-

TAPPING

SCREW

(Reuse.)

2306141T

AII 27573 (0410)

RIGHT REAR

SEAT BACK

2527030T

15 of 22

54. Remove the spare tire cover (one clip).

CLIP

SPARE TIRE

COVER

56. Remove the jack cover and the jack.

JACK

2527051T

55. Remove the trunk weatherstrip in the area shown, then remove the rear trim panel (four clips).

CLIPS (4)

REAR

TRIM

PANEL

JACK COVER

3730010M

57. Remove the hook from the right side trunk liner

(one bolt , hook and washer).

CLIP

HOOK

WASHER

RIGHT SIDE

TRUNK LINER

BOLT

THREADED

HOOK

16 of 22

TRUNK

WEATHERSTRIP

(Remove.)

2527061T

SELF-TAPPING

HOOKS (3)

2527073T

58. Remove the right side trunk liner (three selftapping hooks, one threaded hook and one clip).

58. Inside the trunk area, unplug the high mount brake light harness connector. Inside the cabin, remove the high mount brake light from the rear shelf by releasing the four hooks, and pulling out the brake light assembly. Take care not to damage the clips.

60. Raise the rear seat back. Pull the XM radio harness and DIN cable out from under the floor carpet and toward the passengers' side of the vehicle. Secure the XM radio harness and the DIN cable to the vehicle harness with two wire ties.

DIN CABLE

HIGH-MOUNT

BRAKELIGHT

HOOKS (4)

REAR

SHELF

VEHICLE

CLIP

RADIO

HARNESS

BULB

(If necessary.)

CONNECTOR

3619060M

59. Route the XM radio harness and the DIN cable along the vehicle harness toward the parking brake lever, and under the floor carpet. Secure the

XM radio harness and the DIN cable to the vehicle harness with two wire ties in the areas shown.

WIRE TIE

3620010M

WIRE TIE

XM RADIO HARNESS

AND DIN CABLE

3609010M

AII 27573 (0410)

17 of 22

61. Continue routing the XM radio harness and DIN cable along the vehicle harness toward the trunk.

Using isopropyl alcohol, clean the areas where the cushion tapes will attach, then secure the

XM radio harness and DIN cable to the vehicle panel with five cushion tapes.

63. Inside the trunk, install the two wire ties with clip to the DIN cable, and XM radio harness, and push the clips into the holes in the bulkhead.

WIRE TIE WITH

CLIPS (2)

CUSHION TAPE

BULKHEAD

CUSHION

TAPE

BULKHEAD

HOLES (2)

CABLE

CUSHION

TAPES (5)

3620021M

62. Using isopropyl alcohol, clean the bulkhead area where the cushion tape will attach. To prevent damage to the XM radio harness and DIN cable, attach the cushion tape to the bulkhead edge in the area shown.

BULKHEAD

XM RADIO

HARNESS

3620031M

64. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Attach the

DIN cable and XM radio harness to the vehicle frame with one cushion tape.

Installing the Antenna

65. Get the antenna kit. Route the antenna cable into the trunk area through the high-mount brakelight opening. Clean the edge of the rear shelf, and attach one cushion tape to the edge of the rear shelf.

REAR SHELF

CUSHION

TAPE

ANTENNA

CABLE

18 of 22

AII 27573 (0410)

HIGH-MOUNT

BRAKELIGHT

OPENING

3619111M

66. Temporarily fit the high-mount brake light onto the rear shelf.

HIGH-MOUNT

BRAKE LIGHT

CASE

69. Route the antenna cable through the groove in the high mount brake light case, and reinstall the high mount brake light case.

HIGH-MOUNT

BRAKE LIGHT

CASE GROOVE

REAR TRAY

OPENING

BRAKE LIGHT

CASE

ANTENNA

Clean with isopropyl

3620043M

FRONT

Align FASTENER

67. Using isopropyl alcohol on a shop towel, clean the bottom of the antenna. Remove the adhesive backing from the fastener, then attach the fastener to the bottom of the antenna. Attach the antenna onto the rear rear shelf.

68. Measure and mark the high-mount brake light case. Using a utility knife, cut a groove in the brake light case. Remove any burrs from the edges of the groove.

ANTENNA

CABLE

3627010M

70. Route the antenna cable along the vehicle harness, and secure it to the vehicle harness with seven wire ties in the areas shown.

VEHICLE

HARNESS

WIRE TIES (7)

(Attach near the vehicle harness clips.)

BRAKELIGHT

CASE

Cut.

5 mm

ANTENNA CABLE

3620050M

10 m m

90 m m

3619071M

VEHICLE

HARNESS CLIP

AII 27573 (0410)

19 of 22

71. Attach one wire tie with clip to the antenna cable, the XM radio harness and the DIN cable in the area shown. Push the clip from the wire tie with clip into the body hole.

WIRE TIE

WITH CLIP

BODY

HOLE

ANTENNA

CABLE

DIN CABLE

AND XM

RADIO

HARNESS

72. Route the antenna cable, the XM radio harness, and the DIN cable along the trunk side panel.

Loosely attach the three off-set wire ties with clip around the antenna cable, the XM radio harness, and the DIN cable, then push the clip from each wire tie into the three holes in the trunk side panel.

TRUNK SIDE

PANEL HOLE

OFF-SET WIRE

TIE WITH CLIP

(Note the installation direction.)

PANEL EDGE

EPT SEALER

(Clean this surface with isopropyl alcohol.)

DIN CABLE

XM RADIO

HARNESS

ANTENNA

CABLE

3620060M

TRUNK

SIDE

PANEL

ANTENNA

CABLE

XM RADIO

HARNESS

DIN CABLE

OFF-SET

WIRE TIE WITH

CLIP (2)

(Note the installation direction.)

TRUNK SIDE

PANEL HOLE

3620071M

73. Using isopropyl alcohol on a shop towel, clean the bonding surface on the panel edge, attach one

EPT sealer to the panel edge in the area shown.

20 of 22

74. Install the upper and lower unit brackets to the receiver unit using two 4 x 8 mm washer-screws, and two 4 mm flange nuts for each bracket.

4 mm

FLANGE NUT

4 mm

FLANGE NUT

SCREW

POSITION

SCREW

POSITION

76. Secure the antenna cable, the XM radio harness, and the DIN cable with two wire ties with clip at the measurement shown. Press the clips of the wire ties into the trunk side panel hole and upper unit bracket hole.

TRUNK SIDE

PANEL HOLE

WIRE TIE

WITH CLIPS (2)

ANTENNA

CABLE

240 mm

UPPER

UNIT

BRACKET

LOWER

UNIT

BRACKET

RECEIVER

UNIT

4 x 8 mm

WASHER-

SCREW

4 x 8 mm

WASHER-

SCREW

3623031M

75. Position the receiver unit between the right trunk side panel and the rear fender panel, and plug in the antenna cable connectors, the DIN cable connector, and the XM radio harness connector using the panel hole to access the receiver unit.

BLACK

CONNECTOR

DIN CABLE

XM RADIO

HARNESS

ANTENNA

CABLE

WIRE

TIE

WITH

CLIP

UPPER

UNIT

BRACKET

HOLE

LOWER UNIT

BRACKET HOLE

DIN CABLE

– = 240 mm

3730020M

77. Fold the excess DIN cable, and secure it to the lower unit bracket with one wire tie with clip.

78 Attach the receiver unit/brackets using two

6 x 12 mm washer-bolts through the trunk side panel holes. Tighten the bolts securely.

TRUNK SIDE

PANEL HOLE

ANTENNA

CABLE

DIN

CABLE

XM RADIO

HARNESS RECEIVER

UNIT

3619080M

AII 27573 (0410)

6 x 12 mm

WASHER-

BOLT

6 x 12 mm

WASHER-

BOLTS (2)

3619092M

21 of 22

79. Fold any excess antenna cable, and wrap the excess cable with two EPT sealers. Secure the antenna cable to the XM radio harness with two wire ties in the areas shown. Tighten the off set wire ties you loosely installed in step72.

81. Attach the 5A fuse label over the No. 33 position on the fuse box cover.

FUSE LABEL (5A)

FUSE BOX COVER

No.33

OFF SET WIRE

TIE WITH CLIP

XM RADIO

HARNESS

EPT

SEALERS

(2)

ANTENNA

CORD WIRE TIE

3623012M

80. Install the 5A fuse provided into the No. 33 slot of the fuse box.

FUSE BOX

FUSE (5A)

2219090T

82. Check that all wire harnesses and cables are routed properly and all connectors are plugged in.

83. Reinstall all removed parts. Check that all clips and fasteners are installed securely.

84. Reconnect the negative cable to the battery.

85. Enter the radio anti-theft code, and reset the customer's radio station presets.

86. Set the clock.

87. Set one of the radio station presets to FM 88.7, and check the operation of the XM radio. If necessary, use the XM radio Owner’s Manual supplied.

NOTE: Whenever the battery is disconnected, the driver’s window AUTO up function is disabled.

88. Do the driver's window AUTO up procedure:

• Start the engine. Push down on the driver’s window switch until the window is fully open.

• Pull up on the driver’s window switch to close the window completely, and hold the switch for

2 seconds or more.

• Test the window AUTO up function.

2219080T

22 of 22

Hello! I am an AI chatbot specifically trained to assist you with the Honda 08B15-SDN-100 Installation Instructions Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated