Biamp AUTOONE Operation Manual
Biamp AUTOONE is a versatile automatic mixer with 8 mic/line inputs, each with trim, pad, level, and active/peak indicator. It features NOM attenuation, adaptive threshold sensing, speech-frequency filtering, manual priority override, selectable channel-off attenuation, and selectable last mic hold. Ideal for conferencing, sound reinforcement, and broadcast applications.
Advertisement
Advertisement
autoONE
Automatic Mixer
Operation Manual
Biamp Systems, 10074 S.W. Arctic Drive, Beaverton, Oregon 97005 U.S.A. (503) 641-7287 www.biamp.com
blank
16Feb07
TABLE OF CONTENTS
Front Panel
Rear Panel
Logic Outputs
Specifications
Block Diagram
Warranty
autoONE
pg. 2
INTRODUCTION
The autoONE Automatic Mixer is affordable, extremely versatile, and easy to use. Features include NOM attenuation, adaptive threshold sensing, speechpg. 3 pgs. 4 & 5 frequency filtering, manual priority override, selectable channel-off attenuation, and selectable last mic hold. The autoONE is covered by a five-year warranty.
autoONE features include: pg. 6
♦
eight balanced mic/line inputs on plug-in barrier connectors pg. 7
♦
trim, pad, level, & combined active/peak indicator per channel
♦
channel 1 manual ‘override’ via external contact-closure
♦
channel 8 ‘mix-minus’ assign & ‘ducking’ via channels 1~7
♦
balanced main & aux outputs on plug-in barrier connectors
♦
selectable last mic on, hpf, automix, & 24V phantom power
♦
selectable automix channel-off attenuation (-12dB or -40dB)
♦
pre/post automix assignment to main, aux, & patch outputs
♦
options selectable via external switches (no internal jumpers)
♦
logic outputs from channels for switching of external circuits
♦
Adaptive Threshold Sensing minimizes false gate triggering
♦
Speech-Frequency Filter minimizes false gating due to noise
♦
6dB of hysteresis reduces gate ‘flutter’ when near threshold
♦
‘stacking’ of two units to expand system input capability
♦
incorporates AES recommended grounding practices
♦
marked and UL / C-UL listed power source
♦
covered by Biamp Systems' five-year warranty
1
FRONT PANEL
trim trim trim trim trim trim trim trim autoONE threshold release master
active active active active active active
1 2 3 4 5 6
Active Indicator (Channels 1~8) : These dual-color LEDs provide indication of two channel functions: channel active & peak level.
When a channel is assigned for automixing (gated) operation, the
Active indicator will light green whenever the channel is active
(on). NOTE: The Active indicator does not light green on a channel assigned for manual (ungated) operation. See Channel
DIP Switches on next page.
The Active indicator will also light red whenever channel signal levels reach +10dB (8dB below clipping).
Use this feature to aid in adjusting the Trim controls (see below).
Trim (Channels 1~8) : These controls adjust the channel gain
(0~60dB) to compensate for different input signal levels. For best performance, adjust these controls so the channel Active indictors flash red (+10dB) on occasional peaks. NOTE: Accurate Trim control settings are essential prior to Threshold adjustment (see
Threshold below). Once Threshold has been set, individual channel sensitivities may be fine-tuned using the Trim controls.
If input signals exceed normal operating range of the Trim controls, assign the Pad switch (see DIP switches on next page).
Level (Channels 1~8) : These controls adjust the amount of signal sent from the individual input channels to the mixer output section.
Optimum Level setting is near the 12 o'clock position (unity gain).
Threshold: This control adjusts the minimum signal level
(threshold) at which channels will become active (gate on). The
Threshold circuit also has 6dB of hysteresis, which allows a channel to stay open until the signal level drops below the threshold by 6dB. This hysteresis reduces the tendency for a channel to ‘flutter’ on & off when it detects a signal that is right at the threshold level. Because of the hysteresis, different threshold settings will be arrived at depending on how you adjust this control.
If Threshold is set fully clockwise, then turned counter-clockwise until all channels are easily activated by normal signal levels, the threshold will be as high above ambient noise as possible. If
Threshold is set counter-clockwise, then turned clockwise until no channels are activated by ambient noise, the threshold will allow for greatest channel sensitivity. The threshold is further controlled by Adaptive Threshold Sensing (ATS). ATS monitors signal from active channels and automatically adjusts the threshold to prevent false activation of other channels. NOTE: Accurate Trim control settings are essential prior to Threshold adjustment. Once
Threshold has been set, individual channel sensitivities may be fine-tuned using the Trim controls.
active
7
active
8 aux
-20 on
Release: This control adjusts the length of time that any channel remains active (on) after signal level has dropped below threshold.
Release Time is adjustable from 150 milliseconds to 4 seconds.
Since channels activate very quickly (4 milliseconds Attack Time), precise adjustment of Release Time may not be critical. However, when using Logic Outputs to control external switching circuits
(such as cameras), moderate Release Time settings may provide more appropriate timing (see Logic Outputs on next page).
Master: This control adjusts the level of overall signal sent to the
Main Output. The Main Output level is also affected by automatic
NOM attenuation, which reduces the output level by 3dB for each doubling of active (gated) channels. Optimum Master settings are near the 12 o’clock position (unity gain) or below.
Aux: This control adjusts the level of overall signal sent to the Aux
Output. The Aux Output may be assigned either ungated (pre) or gated (post) signals from the channels (see Master DIP Switches on next page). NOTE: Unlike the Main Output, The Aux Output does not provide automatic NOM attenuation.
-20 Indicator: This dual-color LED provides indication of both signal present & peak level at the Main Output. This indicator will light green when (internal) signal levels reach -20dB (signal present). This same indicator will light red when (internal) signal levels reach +10dB (8dB below clipping). Use this feature to aid in adjusting the Master control. For best performance, adjust the
Master control so the -20 indictor flashes red (+10dB) only on occasional peaks in signal level.
On Indicator: When the Power Cord is plugged in, and power is applied to the autoONE, the red On indicator remains lit.
2
REAR PANEL
27V
~
50/60 Hz
BIAMP SYSTEMS
Portland, Oregon an affiliate of
Rauland-Borg Corp.
main aux stack in main patch patch input patch input patch input patch input patch input patch input patch input patch input
ON ON ON ON ON ON ON ON ON
15 watts class 2 wiring logic outputs expansion outputs
8
AC Power Cord: The power transformer provides 27 Volts AC to the mixer, and is detachable via a 5-pin DIN connector. The mixer has two internal ‘self-resetting’ fuses (there are no user serviceable parts inside the unit). If the internal fuses blow, they will attempt to re-set after a short period. However, this may be an indication that the mixer requires service.
Logic Outputs: This 9-pin Sub-D (male) connector provides logic outputs from the eight channels, plus a common ground. When a channel becomes active, the associated logic output turns on.
Logic Outputs are used to control external circuits for switching speakers, cameras, or indicators (see Logic Outputs on pg. 4).
Expansion: This 6-pin Modular jack is for connection of a second autoONE mixer to add system inputs. When using two autoONE mixers in a system, it is necessary for the mixers to share information regarding active channels. This information allows the mixers to properly perform NOM Attenuation & Adaptive Threshold
Sensing. This connection requires a single Modular cable
(provided). The information shared is processed primarily by the
‘master’ autoONE. To prevent system errors, the second autoONE mixer should be assigned as ‘slave’ (see Master DIP
Switches below). Channel 1 override can be achieved by shorting pins 3 & 6 (see Logic Outputs on pg. 4).
Main Output: These plug-in barrier strip terminals provide the balanced line-level Main Output from the mixer. For balanced connection, wire high (+), low (-), and ground ( d ). For unbalanced connection, wire high (+) and ground ( d ), leaving (-) unconnected.
Signal level will be reduced by 6dB when output is unbalanced.
Main Output level is affected by the front panel Master control, as well as by automatic NOM Attenuation, which reduces the output level by 3dB for each doubling of active (gated) channels.
Aux Output: These plug-in barrier strip terminals provide the balanced line-level Aux Output from the mixer. For balanced connection, wire high (+), low (-), and ground ( d ). For unbalanced connection, wire high (+) and ground ( d ), leaving (-) unconnected.
Signal level will be reduced by 6dB when output is unbalanced.
Aux Output level is affected by the front panel Aux control, but not by automatic NOM Attenuation.
Stack In: These plug-in barrier strip terminals provide a balanced line-level Stack In to the mixer. Signal entering here is combined with signals from the input channels, and is then sent to the Main
Output section. When using multiple autoONE mixers within a system, connect Main Output of one mixer to Stack In of the next mixer, and so forth. All mixers except the final autoONE should be assigned as ‘slaves’ (see Master DIP Switches below). For balanced connection, wire high (+), low (-), and ground ( d ). For unbalanced connection, wire high (+) and ground to both ( d ) & (-).
7 6 5 4 3 2 1
Main Patch: This 3-conductor TRS ¼” phone insert jack is for connection of certain BIAMP products or other external devices at the Main Output section. The Main Patch jack is pre-Master Level, and is wired Tip (send), Ring (return), and Sleeve (ground).
Certain BIAMP products require a single TRS ¼” phone cable for connection. Other devices may require a special ‘Y’ cable. If a pre-Master Level output is desired, connect to Main Patch with Tip
& Ring (send) and Sleeve (ground).
Patch (Channels 1~8) : These 3-conductor TRS ¼” phone insert jacks are for connection of certain BIAMP products or other external devices to the individual input channels. Patch jacks are pre-Channel Level, and are wired Tip (send), Ring (return), and
Sleeve (ground). Certain BIAMP products require TRS ¼” phone cables for connection. Other devices may require special ‘Y’ cables. If a pre-Channel Level direct output is desired, connect to
Patch with Tip & Ring (send) and Sleeve (ground). Patch jacks may be individually assigned pre-gate or post-gate signal (see DIP
Switches below).
Input (Channels 1~8) : These plug-in barrier strip terminals provide the balanced mic/line Inputs to the mixer. For balanced connection, wire high (+), low (-), and ground ( d ). For unbalanced connection, wire high (+) and ground to both ( d ) & (-). Phantom power (+24VDC) is available (see DIP Switches below).
Master DIP Switches: These switches assign functions to the mixer as a whole (when pushed up). Slave assigns the mixer as an expander to a ‘master’ mixer. -12dB selects -12dB channel-off attenuation (instead of -40dB). HP Filter assigns a high-pass filter of 6dB/octave @ 170Hz. Last Mic causes the most recently active channel to remain on. Aux Post assigns post-gate/level channel signals to the Aux Output (instead of pre-gate/level signals).
DIP Switches (Channels 1~8) : These switches assign functions to the individual channels (when pushed up). Pad attenuates input signal -18dB (line input). Ungated turns channel on (defeats gate).
Phantom turns on +24V phantom power (for condenser mics).
Duck Ch 8 (Channels 1~7 only) assigns channel signal to activate
-12dB attenuation on Channel 8 (ducking). Aux Off (Channel 8 only) removes Channel 8 signal from Aux Output (mix-minus).
Patch Pre assigns pre-gate channel signal to channel Patch jack
(instead of post-gate channel signal).
3
LOGIC OUTPUTS
The autoONE provides eight logic outputs on a rear panel 9-pin Subminiature D (male) connector. Logic Outputs can be used to control external switching circuits for speakers, cameras, indicators, etc. The autoONE Logic Outputs are most often used, in conjunction with external relays, to turn off specific speakers when nearby microphones are active (reducing feedback problems). For example, if a speaker is located directly above microphone #1, the Logic Output for Channel 1 of the autoONE can be used to turn off that speaker relay when microphone #1 is active (see diagram on next page). The Logic Outputs can also be combined (wired in parallel) to control a single circuit.
For example, a speaker relay could be turned off when either microphone #1 or microphone #2 is active. In addition to speaker relays, the autoONE Logic Outputs may be used to control external indicator lights (see diagram on next page). Another common application for
Logic Outputs is to control video cameras. Different cameras could be activated depending upon which microphone (or group of microphones) is currently active. Cameras can be selected using a video switcher and/or ‘pan/tilt/zoom’ camera presets. The Logic
Outputs may also be used in conjunction with the Expansion jack (pin 6 & pin 3) to perform ‘automatic priority’, which allows all other channels to be muted whenever the Channel 1 microphone is active (see diagram on next page). The Logic Output (pin 1) & ground (pin
9) terminals for the Channel 1 ‘priority’ microphone are wired to pin 6 & pin 3 respectively of the Expansion jack. A switch or contactclosure may instead be used, for manual priority override.
The autoONE Logic Outputs are ‘open collector’ outputs. Each Logic Output is an NPN transistor with the collector being the output and the emitter being ground (see diagram on next page). When a Logic Output is turned on, the transistor provides a path for DC current to flow. The Logic Outputs do not provide any voltage or current. They act only as switches (with a common ground return). To activate external relays, an external power supply must be used (see diagram on next page). The Logic Output transistors are rated up to a maximum of 24 VDC and 50 mA per output (24 volt relay coils maximum). However, +12 Volts DC is sufficient power for most applications. When using the Logic Outputs to control relays, protection diodes must be used to suppress high voltage transients that are generated when the relays turn off (see diagram on next page). Any of the 1N4004 family of diodes (1N4001, 1N4002, 1N4003, 1N4004,
1N4005, 1N4006, 1N4007, or equivalent) will provide proper protection. When a Logic Output goes on, the associated relay may be wired to perform on, off, or ’A/B’ switching functions. To use logic ‘on’ to turn on (or activate) a device, wire across the ‘normally open’ relay contacts, in series with the device (or control voltage source). To use logic ‘on’ to select between ‘A’ or ‘B’ signals (inputs or outputs), wire one signal to the ‘normally closed’ relay terminal and the other signal to the ‘normally open’ relay terminal, with the common relay terminal providing the feed (input or output).
The 9-pin Sub-D connector used for the autoONE Logic Outputs is the same type of connector used for RS-232 communications ports on
IBM compatible computers. A cable may be created by simply wiring to the proper pins of a female 9-pin Sub-D cable-end connector. logic out pin number channel 1 pin #1
1 2 3 4 5
6 7 8 9
logic outputs
channel 2 channel 3 channel 4 channel 5 channel 6 channel 7 channel 8 ground pin #2 pin #3 pin #4 pin #5 pin #6 pin #7 pin #8 pin #9
5
4
9 8
3
2
7 6
1
9-pin cable-end
4
LOGIC OUTPUTS
autoONE
Logic/Relay circuit
+12 Volts DC
Power Supply
− +
12V Relay
Pin #1
Contacts normally closed common normally open
Logic Output #1
1N4004
Diode
Coil
Pin #9
autoONE
Pin #1
Logic Outputs controlling indicators
+12 Volts DC
Power Supply
− +
Indicator Panel
Logic Output #1
1.2k ohms
LED
Pin #9
Channel 1 ‘automatic’ (logic output) or ‘manual’ (external switch) override of Channels 2~8
6 3 external switch
1
9
logic outputs
ground
expansion
5
SPECIFICATIONS
Frequency Response (20Hz~20kHz @ +4dBu) : +0/-0.5dB
THD + Noise (20Hz~20kHz @ +4dBu) :
Output Noise (20Hz~20kHz, main & 1 channel @ nominal) :
< 0.03%
< -75dBu
main & aux outputs
channel & main patch
Maximum Gain:
mic/line input to main/aux outputs
channel patch to main/aux outputs
main patch to main output
main stack to main output
Crosstalk (channel-to-channel @ 1kHz)
Output Impedance:
main & aux outputs (balanced)
channel & main patch (unbalanced)
Input Impedance:
mic/line input (balanced)
channel patch (unbalanced)
main patch (unbalanced)
main stack (balanced)
:
Maximum Input:
86dB mic/line input, channel & main patch
26dB
16dB
main stack
High-Pass Filter:
+24dBu
+18dBu
+18dBu
+24dBu
6dB/octave @ 170Hz
10dB Automixing:
< -65dB gate attack time 4mSec
150mSec to 4Sec release time (adjustable)
200 ohms threshold (adjustable) -32dBu to -8dBu
-12dB or -40dB 100 ohms channel-off attenuation (selectable)
NOM attenuation (doubling of active inputs) -3dB
9dB 4.7k ohms Feedback/Noise Improvement (8 channels)
5.3k ohms Power Consumption (115/230VAC 50/60Hz) : < 15 watts
6.7k ohms Dimensions (HxWxD) : 1.75”x19”x11”
28k ohms Weight: < 10 lbs. (4.55kg)
6
BLOCK DIAGRAM
+24V
Input Channels input
3
2
1 phantom power trim discrete transistor preamp
18dB pad gate open peak detect
+10dB autoONE Block Diagram
attenuator
(gate)
attenuator
(gate) channel patch aux pre bus aux disable
(Ch.8 only) aux post bus level
ATS ungated patch pre-gate channels 1-7 only signal detect mute bus channel 8 only
12dB mute mute logic
-12/-40dB threshold release priority slave bus
(Ch.1 only) last mic hold gate control logic count bus priority bus open collector output driver logic output
(gate open)
-12dB bus mix bus
Master Section main stack
3
2
1 mix bus
Σ
Expansion priority bus
ATS main patch threshold release time master level external control voltage
-20
VCA
HP filter aux pre bus aux post bus slave aux level peak aux pre/post count bus
Adaptive
Threshold
Sensing threshold release priority
NOM logic last mic hold
VCA control output channel gate logic main output
3
2
1 aux output
3
2
1
7
WARRANTY
BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE
ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL
1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below.
2. If you notify BIAMP during the warranty period that a BIAMP
Systems product fails to comply with the warranty, BIAMP
Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer.
Transportation and insurance charges to and from the BIAMP
Systems factory for warranty service shall be your responsibility.
3. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP
Systems' recommendations.
4. Electro-mechanical fans, electrolytic capacitors, and normal wear and tear of items such as paint, knobs, handles, and covers are not covered under this warranty.
Biamp Systems
10074 S.W. Arctic Drive
Beaverton, Oregon 97005
(503) 641-7287
5. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. BIAMP SYSTEMS
DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
6. The remedies set forth herein shall be the purchaser's sole and exclusive remedies with respect to any defective product.
7. No agent, employee, distributor or dealer of Biamp Systems is authorized to modify this warranty or to make additional warranties on behalf of Biamp Systems. statements, representations or warranties made by any dealer do not constitute warranties by Biamp Systems. Biamp Systems shall not be responsible or liable for any statement, representation or warranty made by any dealer or other person.
8. No action for breach of this warranty may be commenced more than one year after the expiration of this warranty.
9. BIAMP SYSTEMS SHALL NOT BE LIABLE FOR SPECIAL,
INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
INCLUDING LOST PROFITS OR LOSS OF USE ARISING
OUT OF THE PURCHASE, SALE, OR USE OF THE
PRODUCTS, EVEN IF BIAMP SYSTEMS WAS ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
585.0145.90A

Public link updated
The public link to your chat has been updated.
Advertisement