Sharp MX-B381, MX-B401 Installation Manual

PDF

Document

TopPage

INSTALLATION MANUAL

CODE: 00ZMXB401/I2E

DIGITAL MULTIFUNCTIONAL

SYSTEM

MODEL

MX-B381

MX-B401

CONFIGURATION

[1] MX-B381/B401 (MAIN UNIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[2] MX-CSX1/CSX2 (500-SHEET PAPER FEED UNIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

[3] MX-FN12 (FINISHER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

[4] MX-FXX3 (FACSIMILE EXPANSION KIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

[5] AR-PF1 (BARCODE FONT KIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

[6] MX-FR16U (DATA SECURITY KIT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

[7] MX-FWX1 (INTERNET FAX EXPANSION KIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[8] MX-PUX1 (XPS EXPANSION KIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

[9] MX-AMX1 (APPLICATION INTEGRATION MODULE) . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

[10] MX-AMX2 (APPLICATION COMMUNICATION MODULE) . . . . . . . . . . . . . . . . . . . . . 10-1

[11] MX-AMX3 (EXTERNAL ACCOUNT MODULE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

[12] MX-SMX3 (EXPANSION MEMORY BOARD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

[13] DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MAIN UNIT . . . . . . . . . 13-1

[14] DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MX-CSX1/CSX2 . . . . . 14-1

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used for after sales service only.

The contents are subject to change without notice.

CONFIGURATION

System configuration . . . . . . . . . . . . . . . . . . . . . .i

Machine configuration . . . . . . . . . . . . . . . . . . . . ii

Option list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

[1] MX-B381/B401 (MAIN UNIT)

Installing (use) conditions . . . . . . . . . . . . . . . 1-1

Transit and delivery . . . . . . . . . . . . . . . . . . . . 1-2

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

[2] MX-CSX1/CSX2 (500-SHEET PAPER FEED UNIT)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

[3] MX-FN12 (FINISHER)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

[4] MX-FXX3 (FACSIMILE EXPANSION KIT)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

[5] AR-PF1 (BARCODE FONT KIT)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

[6] MX-FR16U (DATA SECURITY KIT)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

[7] MX-FWX1 (INTERNET FAX EXPANSION KIT)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[8] MX-PUX1 (XPS EXPANSION KIT)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

[9] MX-AMX1 (APPLICATION INTEGRATION MODULE)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

[10] MX-AMX2 (APPLICATION COMMUNICATION

MODULE)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

[11] MX-AMX3 (EXTERNAL ACCOUNT MODULE)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1

[12] MX-SMX3 (EXPANSION MEMORY BOARD)

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

[13] DEHUMIDIFIER HEATER KIT (SERVICE PARTS)

FOR THE MAIN UNIT

Heater kit contents list . . . . . . . . . . . . . . . . . 13-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

Check after installation. . . . . . . . . . . . . . . . . 13-4

[14] DEHUMIDIFIER HEATER KIT (SERVICE PARTS)

FOR THE MX-CSX1/CSX2

Heater kit contents list . . . . . . . . . . . . . . . . . 14-1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

Check after installation. . . . . . . . . . . . . . . . . 14-5

1. System configuration

Service Manual

MX-BTX1

Business card feeder

MX-B381/B401

Digital multifunctional system

MX-FN12

Finisher

MX-SCX1

Staple cartridge

MX-CSX1

500-sheet paper feed unit

MX-CSX1

500-sheet paper feed unit

MX-CSX2

500-sheet paper feed unit

MX-FXX3

Facsimile expansion kit

MX-SMX3

Expansion memory board

MX-FWX1

Internet fax expansion kit

AR-PF1

Bar code font kit

MX-CSX1

500-sheet paper feed unit

MX-CSX2

500-sheet paper feed unit

MX-CSX2

500-sheet paper feed unit

MX-FR16U

Data security kit

(Commercial version)

MX-AMX1

Application integration module

MX-AMX2

Application communication module

MX-AMX3

External account module

MX-USX1

Sharpdesk 1 license kit

MX-USX5

Sharpdesk 5 license kit

MX-US10

Sharpdesk 10 license kit

MX-US50

Sharpdesk 50 license kit

MX-USA0

Sharpdesk 100 license kit

MX-PUX1

XPS expansion kit

MX-B381/B401 CONFIGURATION - i

2. Machine configuration

Main body LCD

RSPF

Automatic duplex

HDD

System memory (For Program, Printer)

Local memory (Copier)

Copier

GDI printer

SPDL/PCL printer

PS printer

EFI printer

FAX

Internet Fax

Network scanner

Filing

Security

MX-B381/B401

CL 8.5

STD

512MB

STD

–

STD

–

OPT

OPT *1

STD

OPT *1

STD: Standard provision, OPT: Option, –: No setting

*1: Product key target

3. Option list

Paper feed system

Model

Paper exit system

Electrical system (ROM)

Electrical system (Software)

Memory

Name

500-sheet paper feed unit

Business card feeder

Finisher

Bar code font kit

Data security kit

Internet fax expansion kit

XPS expansion kit

Sharpdesk 1 license kit

Sharpdesk 5 license kit

Sharpdesk 10 license kit

Sharpdesk 50 license kit

Sharpdesk 100 license kit

Application integration module

Application communication module

External account module

Facsimile expansion kit

Expansion memory board

STD: Standard provision, OPT: Option, –: No setting

*1: To install the MX-PUX1, the MX-SMX3 is required.

Model name

MX-CSX1

MX-CSX2

MX-BTX1

MX-FN12

AR-PF1

MX-FR16U

MX-FWX1

MX-PUX1

MX-USX1

MX-USX5

MX-US10

MX-US50

MX-USA0

MX-AMX1

MX-AMX2

MX-AMX3

MX-FXX3

MX-SMX3

MX-B381/B401

OPT

OPT *1

OPT

Product key target

–

Yes

–

Yes

–

Yes

–

MX-B381/B401 CONFIGURATION - ii

Service Manual

1. Installing (use) conditions

Before installing the machine, check that the following installing

(use) conditions are satisfied.

If the installing (use) conditions are not satisfied, the machine may not display full performances, resulting in troubles. It may also cause safety problems. Therefore, be sure to arrange the installing

(use) conditions before setting up the machine.

No.

Content

Bringing space

Installing space

Power source (Capacity, fluctuation, safety)

Floor strength

Direct rays of the sun, dust, temperature, humidity, gases, chemicals

A. Bringing space

For installation of a large size machine, be sure to check that the door size is wide enough before bringing in.

B. Installing space

The following space must be provided around the machine in order to assure machine performances and proper operations.

If any option is installed, provide the additional space for installing it.

Especially the space at the rear of the machine must be provided sufficiently. If not, the machine cannot exhibit functions against heat and dust, causing some troubles.

(4) Safety

Be sure to properly ground the machine.

Grounding (earth connection) must be performed before inserting the power plug into the power outlet.

When disconnecting the earth connection, be sure to disconnect the power plug from the power outlet in advance.

(5) Power plug

Check the form of the power plug. If the shape does not match, do not use it.

D. Floor strength and level

This machine is considerably heavy and becomes heavier with an option installed.

The floor must be strong enough for assuring safety.

If the unit is not horizontally installed, the toner density control is not performed normally, degrading the copy quality.

If not, color shift or image distortion may occur.

11-13/16”

(30cm)

11-13/16”

(30cm)

17-23/23”

(45cm)

C. Power source (Capacity, voltage, frequency, safety, plug)

If the power specifications are not satisfied, the machine cannot exhibit full performances and may cause safety trouble.

Strictly observe the following specifications.

(1) Power capacity

Check that the following power capacity is satisfied. If not, additionally provide a power source.

Current capacity

Japan: 20A or more

100V: 15A or more

200V: 10A or more

(2) Power voltage

Measure the voltage during copying to check that the voltage is in the range of the specified voltage  10%.

If the voltage is outside the specified range, use thicker lead wires to reduce impedance.

(An electrical work is required.)

Use of a step-up transformer is also available. In this case, the capacity must be great enough for the max. power consumption of the machine.

(3) Power frequency, waveform

The frequency must be within the range of the specified frequency

 2%. If power waveform is deformed, a trouble may occur.

E. Direct rays of the sun, dust, temperature, humidity, gasses, chemicals, vibration

(1) Temperature and humidity

This machine is designed to perform properly under the specified temperature and humidity. If the temperature and humidity exceeds the specified range, the machine may not operate properly and or cause equipment failure.

Especially when the humidity is too high, paper absorbs humidity to cause a paper jam or dirty copy.

Do not install the machine near a heater, a cooler, or a humidifier.

Dew may be formed inside the machine to cause a trouble. Use enough care for ventilation.

H umidity 㧔 RH 㧕

8 5 %

6 0 %

2 0 %

• Working environment

Temperature: 10 to 35  C

Humidity: 20 to 85% RH

Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 1

(2) Dust

If dust enters the machine, it may cause dirty copy and a paper jam, resulting in a shortened lifetime.

(3) Direct rays of the sun

If the machine is installed under the rays of the sun, the exterior of the machine may be discolored and abnormal copies may be produced.

2. Transit and delivery

No.

Content

Implements, facility, and man power

Delivery

Method

Use a forklift. (If no forklift is available, manpower of two persons is required.)

Transit must be made in packed condition.

A. Implements, facility, and manpower

It is recommendable to use a forklift for bringing in the machine for safety.

If no forklift is available, man-power of two persons is required. The machine is considerably heavy, and requires safety precautions for delivery and installation.

Transit of the machine must be made in packed condition to the installing place.

Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit.

B. Delivery

Remove the packing materials prior to installation in the office environment.

3. Unpacking

A. Unpacking procedure

1) Remove the PP band.

2) Remove the top case.

3) Remove the parts included in the package.

(4) Gases and chemicals

Do not install the machine at a place where there are gases and chemicals. Especially be careful to avoid installation near a diazotype copier, which produces ammonium gas.

Copy quality may be adversely affected and a trouble may be caused.

(5) Vibration

Avoid installation near a machine which produces vibrations.

If vibrations are applied to the copier machine, copy images may be deflected and a trouble may be caused.

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 2

4) Remove the carton.

5) Remove the parts included in the package.

6) Remove the main unit from the bottom padding, and remove the polyethylene bag.

C. Check the packed items

1) Check that all the parts are in the package.

1 2 3

4 5 6

No.

Packed part names

Developer cartridge

Waste toner box

AC cord

Operation Manual

Operation Manual pocket

Toner cartridge

Quantity

200V series only: 1 piece

1 set

Yes

Europe only: 1 piece

4. Installation

A. Installation of the developer cartridges

1) Open the front cover.

B. Removal of the fixing tape and protection material

2) Turn the lock lever until it stops to release the lock, and remove the waste toner box.

NOT E :

For N orth America , the po w er cable is attached vertically to the machine .

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 3

3) Turn the lock lever to the horizontal position to release the lock, and open the drum positioning plate unit.

5) While pressing the developer cartridge, pull out the heat seal straight.

NOTE: If the heat seal is pulled out with a strong force or diagonally, it may be broken off. Be sure to pull it slowly and straight.

After puling out the heat seal completely, check to confirm that there is a red mark at the edge of the heat seal.

If there is no red mark, it means that the heat seal has been broken. In such a case, the developer cartridge must be replaced with a new one.

4) Shake the developer cartridge 5 - 6 times horizontally, and remove the protection material from the developer cartridge.

Insert the developer cartridge straight and horizontally until it locks.

NOTE: When handling the developer cartridge, do not touch the magnet roller section and the shutter section.

6) Close the lock cover of the developer cartridge.

7) Close the drum positioning plate unit, and put the lock lever upright to lock.

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 4

B. Cleaning of LSU's dust-proof glass

* Dust from the transfer belt or shutter or some other adjacent part may fall onto the LSU during transport or installation. Be sure to clean the dust-proof glass before checking the image quality.

1) Remove the LSU cleaning rod from the front cover.

5) Install the waste toner box, and turn the lock lever to the left until it stops to lock the waste toner box.

2) Face the cleaner downward, and slowly insert the LSU cleaning rod into the LSU cleaning hole.

* The LSU cleaning hole is indicated with a label.

6) Close the front cover.

Cleaning side

3) After inserting the LSU cleaning rod to the bottom, pull it out until the lead edge of the cleaning unit is separated from the

LSU clearing surface. Repeat 2 - 3 times for cleaning.

4) Return the LSU cleaning rod to the front cover.

C. Installation of the operation manual pocket

1) Install the Operation Manual pocket (included in package) cover to the left side of the machine.

a) First, insert the pawl on the lower side of the Operation

Manual pocket.

b) Then, lift the pawl on the upper side and insert it, and slide down to install.

D. Tray size setup

1) Gently pull out the tray until it stops. If paper remains in the tray, remove it.

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 5

2) Adjust the guide plates A and B to the vertical size and the horizontal size of paper.

The guide plates A and B are movable. Hold the fixing knob to slide the guide plates A and B to match the paper size.

2) Remove the heat seal.

3) Insert the toner cartridge horizontally and straight until it locks.

3) Insert the tray slowly.

The machine automatically detects the set paper size.

4) Close the cabinet and turn on the power.

The toner concentration adjustment operation is automatically started, and "Please wait. Do not turn the power off." is displayed.

When the toner concentration adjustment operation is completed, the message of "Install the toner cartridge." is displayed. Do not make any operations until the message is displayed.

E. Installation of toner cartridges

* The life of each toner cartridge is as follows:

Equivalent to approximately 2.5K (A4/LT 5%)

1) Shake the toner cartridge (included in package) horizontally several times.

NOTE: Do not forcibly insert the toner cartridge. Keep holding the cartridge and completely insert it.

NOTE: When the machine is transported with the developing unit removed, be sure to remove the toner cartridge. (if not toner may become clogged.)

NOTE: Do not remove or insert the toner cartridge with the developer cartridge removed.

F. Specifications setting

Use SIM26 to set to the specifications according to the customer's request.

SIM No

26 6 Destination setting

Content

To customize one of the following items after destination setting, change the set value of the item.

SIM No Content

26 3 Auditor specifications, mode setting

18 Toner save mode enable/disable setting (Japan and UK versions only)

* For the other destinations, this setting is made by the user program.

52 Count-up enable/disable setting of non-print paper passing for each counter

53 User auto calibration enable/disable setting

65 Staple limit quantity setting

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 6

G. Image off-center adjustment

Make a copy in the document table mode and in the RSPF mode, and check to confirm that the void area is within the specified range shown below.

NOTE: When an option cassette is installed, execute this adjustment.

(1) Image off-center automatic adjustment

(Document table mode)

1) Enter the SIM50-28 mode.

&/26(

$872,0$*(326,7,21$'-8670(176(59,&(

2&$'-

63)$'-

5(68/7

%.0$*$'-

66(78335,17$'-

'$7$

5) Press [EXECUTE] key.

The adjustment pattern is printed out. (Paper is fed from the selected paper feed tray, and the adjustment pattern of each paper feed tray is printed out.)

6) Set the adjustment pattern to the center reference position on the document table.

NOTE: Fit the adjustment pattern correctly with the document guide.

2) Select [SETUP/PRINT ADJ].

3) Select [OFFSET].

$872,0$*(326,7,21$'-8670(176(59,&(

/($'

$//

2))6(7

&/26(

7) Press [EXECUTE] key.

$872,0$*(326,7,21$'-8670(176(59,&(

3/($6(:$,7

12:(;8&87,1*

&/26(

(Note)

When [ALL] is selected, the adjustments of the following two items are performed at a same time.

* [LEAD]: Print image lead edge image position adjustment

* [OFFSET]: Print image off-center adjustment

4) Select a paper feed tray to be adjusted.

Set A4 (11" x 8.5") paper in each paper feed tray in advance.

&/26(

$872,0$*(326,7,21$'-8670(176(59,&(

0)7 &6

&6 &6

&6 $'8

5(35,17 (;(&87(

The following item is automatically adjustment.

* Print image lead edge image position adjustment

* Print image off-center adjustment

Perform the procedures of 6) - 7) for the printed adjustment pattern of each paper feed tray.

8) Press [OK] key.

The adjustment result becomes valid.

&/26(

$872,0$*(326,7,21$'-8670(176(59,&(

35,17/($'0)7&$6$'8

&$6'6.

35,172))6(70)7&$6&$6$'8

&$6&$6

(;(&87(

5(35,17 5(6&$1 5(75< '$7$ 2.

NOTE: When an error occurs in the automatic adjustment of

SIM50-28, place white paper on the adjustment pattern and perform the adjustment.

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 7

H. Remote operation panel function Enable setting

(1) General

To use the remote operation panel function, the password for the remote operation panel function must be entered on the password input menu displayed on the VNC boot screen. Note that, therefore, the password must be set in advance to use the remote operation panel function.

Let the user make the password, and use SIM26-78 to set it.

(2) Remote operation panel function password setting procedures

1) Enter the SIM26-78 mode.

&/26(

523(3$66:25'6(77,1*

35(6(17˖

ǂǂ1(:˖

6(7

J. USB PORT selection

There are two USB ports, one on the rear frame side and the other on the front frame side. Only either of them can be used.

When shipping, the port on the front frame side is valid and the port on the rear frame side is invalid.

The valid port can be switched by changing the setting of the MFP

PWB DIP SW.

Select the valid USB port according to the user's request.

MFP PWB DIP SW

SW 1 SW 2

OFF

USB I/F

Port on the front frame side

Port on the rear frame side

Valid

Invalid

Valid

OFF

SW1

SW2

2) Enter the password with 10 key. (Within 5 - 8 digits)

The entered password is displayed on the column of "NEW."

To modify the entered password, use clear key to delete the password digit by digit.

3) Press [SET] key, and the password is set.

I. Functional operation check

Check to confirm that the following operations are normal.

Check item

Key input operation (Operation panel)

Display (Operation panel)

Paper feed operation

Manual paper feed

Main unit paper feed tray

Equipment

Option paper feed unit With the option paper feed unit installed

Manual paper feed tray Paper size detection operation

RSPF operation /

Duplex copy operation

S-S mode

D-S mode

S-D mode

D-D mode

Stapling operation

Offset operation

With the finisher installed

K. Storing setting and adjustment data

Use SIM22-6 to print and store the settings and adjustments data

(list).

• When a memory trouble occurs, if the above information is not available, all the adjustments must be performed from the beginning.

• If the above information is available, the setting and adjustment values can be directly entered, shortening the servicing time.

L. Procedures required for transit of the machine

1) If the following option is installed, remove it from the machine.

• Finisher

2) Remove the following consumable parts from the machine.

• Paper

• Toner cartridge

• Developer cartridge

NOTE: When moving take extreme care to prevent shock or vibration to the machine as there is a hard drive built into this product.

MX-B381/B401 MX-B381/B401 (MAIN UNIT) 1 – 8

1. Unpacking

A. Removal of the 500 sheet paper feed unit

(1) MX-CSX1/CSX2

2. Installation

<Precautions for installation>

Before execution of installation, check to confirm that the communication lamp on the operation panel and the data lamp under it are not lighted or blinking.

A. Turn off the power of the main unit

1) Turn OFF the power switch on the operation panel.

B. Removal of the fixing tape and protection material

(1) MX-CSX1/CSX2

1) Remove the 500 sheet paper feed unit from the polyethylene bag, and remove the fixing tape and the protection material.

2) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch.

3) Disconnect the power plug from the power outlet.

B. Install the MX-CSX1 or the MX-CSX2 to the MX-

CSX2.

* In the example below, installation of the MX-CSX1 to the MX-

CSX2 is described. Installation of the MX-CSX2 to another MX-

CSX2 is performed similarly.

1) Put the MC-CSX1 on the MX-CSX2 so that they fit together.

NOTE: When holding the main unit with the MX-CSX2 and the

MX-CSX1 installed, use two persons.

MX-B381/B401 MX-CSX1/CSX2 (500-SHEET PAPER FEED UNIT) 2 – 1

4) Hang the fixing clasp on the main unit, and tighten the hand screws.

5) Push in and close the trays.

* When the MX-CSX1 is put on the MX-CSX2, it is automatically locked at the left and the right of the rear side.

C. Install the main unit to the MX-CSX1.

NOTE: If the main unit is combined with the MX-CSX1 only, it must be used as a desktop machine and must not be used on the floor in order to prevent against falling.

1) Put the main unit on the MX-CSX1 so that they fit together.

NOTE: When holding the main unit, use two persons.

2) Pull out the trays of the MX-CSX1 and the MX-CSX2.

3) Loosen the hand screws on the left and the right sides.

MX-B381/B401 MX-CSX1/CSX2 (500-SHEET PAPER FEED UNIT) 2 – 2

* When the main unit is put on the MX-CSX1, it is automatically locked at the left and the right of the rear side.

5) Push in and close the trays.

2) Pull out the tray of the main unit and that of the MX-CSX1.

D. Turn on the power of the main unit

1) Power to the main unit.

3) Loosen the hand screws on the left and the right sides.

2) Turn ON the power switch.

4) Hang the fixing clasp on the main unit, and tighten the hand screws.

3) Turn ON the power switch on the operation panel.

MX-B381/B401 MX-CSX1/CSX2 (500-SHEET PAPER FEED UNIT) 2 – 3

3. Adjustments

A. Image off-center automatic adjustment

(Document table mode)

1) Enter the SIM50-28 mode.

5) Press [EXECUTE] key.

The adjustment pattern is printed out. (Paper is fed from the selected paper feed tray, and the adjustment pattern of each paper feed tray is printed out.)

6) Set the adjustment pattern in the center reference on the document table.

NOTE: Fit the adjustment pattern correctly with the document guide.

2) Select [SETUP/PRINT ADJ].

3) Select [ALL].

7) Press [EXECUTE] key.

NOTE: When [ALL] is selected, the adjustments of the following two items are performed at a same time.

* [LEAD]: Print image lead edge image position adjustment

* [OFFSET]: Print image off-center adjustment

4) Select the paper feed trays to be adjusted. (Select all the trays.)

Set A4 (11" x 8.5") paper in each paper feed tray in advance.

The following item is automatically adjustment.

* Print image lead edge image position adjustment

* Print image off-center adjustment

Perform the procedures of 6) - 7) for the printed adjustment pattern of each paper feed tray.

8) Press [OK] key. (For the 4.3 Inch LCD model, press the OSA shortcut key.)

The adjustment result becomes valid.

NOTE: When an error occurs in the automatic adjustment of

SIM50-28, place white paper on the adjustment pattern and perform the adjustment.

MX-B381/B401 MX-CSX1/CSX2 (500-SHEET PAPER FEED UNIT) 2 – 4

1. Unpacking

A. Removal of the finisher

<Precautions for installation>

Before execution of installation, check to confirm that the communication lamp on the operation panel and the data lamp under it are not lighted or blinking.

A. Turn off the power of the main unit

1) Turn OFF the power switch on the operation panel.

B. Removal of the fixing tape and protection material

1) Remove the finisher from the polyethylene bag, and remove the fixing tape and the protection materials.

2) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch.

3) Disconnect the power plug from the power outlet.

C. Check the packed items

1 2

No.

Packed part names

Machine connection unit

Paper exit tray

Staple position label (For RSPF)

Staple position label (For OC)

Quantity

MX-B381/B401 MX-FN12 (FINISHER) 3 – 1

B. Installation of the machine connection unit

1) Remove the full detection actuator and the paper exit auxiliary plate at the paper exit port of the main unit.

5) Install the machine connection unit (included in the package) to the machine.

2) Disengage the pawls, and remove the paper exit cover.

6) Slide the lock lever to " (Lock)" position and fix it.

3) Open the front cover.

C. Installation of the finisher

1) Install the finisher to the machine connection unit.

NOTE: When holding the finisher, hold the front frame side and the rear frame side together.

4) Remove the coin screw, and remove the paper exit tray.

2) Close the front cover of the finisher.

MX-B381/B401 MX-FN12 (FINISHER) 3 – 2

3) Close the front cover of the main unit.

2) Attach the staple position label (include in the package) for the

OC to the scanner unit.

D. Installation of the paper exit tray

1) Install the paper exit tray (included in the package) to the finisher.

F. I/F cable connection

1) Remove the cap of the connector for connecting the finisher to the rear side of the machine.

Connect the I/F cable of the finisher, and loosen the manual screw of the connector and fix it.

Non LPS

Do not connect to devices other than specified peripheral devices of our company.

E. Staple position label attachment

1) Attach the staple position label (included in the package) for the RSPF to the RSPF unit.

G. Turn on the power of the main unit

1) Insert the power plug into the power outlet.

MX-B381/B401 MX-FN12 (FINISHER) 3 – 3

2) Turn ON the power switch.

3) Turn ON the power switch on the operation panel.

3) Enter the set value with 10-key. (Press [C] key to clear the entered values.)

Initial value: 50

When the adjustment value is increased by 1, the alignment plate F/R width is narrowed by 0.419mm in alignment operation.

When the adjustment value is decreased by 1, the alignment plate F/R width is widened by 0.419mm in alignment operation.

The alignment plate F and the alignment plate R cannot be adjusted separately. The shift amount on the F side and that on the R side are alternatively corrected every-time the adjustment value is increased by 1. (Correction with 51 for the F side, and 52 for the R side. ... 59 for the F aide, and 60 for the

R side. Similar when the set value is decreased.)

4) Press [OK] key to save the set value. (For the 4.3 Inch LCD model, press the OSA shortcut key.)

5) After completion of the adjustment, make staple copies.

Alignment specification: Within 2.5mm

B. Paper delivery roller descending position adjustment

This adjustment is executed when a paper exit jam occurs or when roller marks of the paper delivery roller are attached to paper.

1) Execute Sim3-10.

2) Select "B: FDRLM ADJUST".

3. Adjustments

The adjustments of this machine are executed only when a trouble occurs.

If the adjustment value is changed when there is no trouble in the machine, a trouble may be generated such as improper alignment of paper, paper exit jam, attachment of roller marks on paper, etc.

A. Paper alignment width adjustment

This adjustment is executed when a trouble occurs in paper alignment.

1) Execute Sim3-10.

2) Select "A: FPAM ADJUST".

3) Enter the set value with 10 key. (Press [C] key to clear the entered values.)

Initial value: 50

When the adjustment value is increased by 1, the shift amount of the paper delivery roller is changed by 0.11mm toward the pressure increasing side (*1).

When the adjustment value is decreased by 1, the shift amount of the paper delivery roller is changed by 0.11mm

toward the pressure decreasing side (*1).

*1: The pressure increasing side means the direction to increase the paper delivery roller pressure onto paper, and the pressure decrease side means the direction to decrease the paper delivery roller pressure onto paper.

4) Press [OK] key to save the set value.

MX-B381/B401 MX-FN12 (FINISHER) 3 – 4

1. Unpacking

A. Check the packed items

4 5 6

Australia

2) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch.

3) Disconnect the power plug from the power outlet.

No.

Packed part names

FAX memory

Ferrite core

Line cable

Screw (M3)

Step screw

Clamp

Instructions for installation

Quantity

2. Installation

<Precautions for installation>

Before execution of installation, check to confirm that the communication lamp on the operation panel and the data lamp under it are not lighted or blinking.

A. Turn off the power of the main unit

1) Turn OFF the power switch on the operation panel.

B. FAX unit installation

1) Remove the two screws on the rear cabinet of the main unit.

Attach the step screw (included in the package) to one of the removed screw positions.

MX-B381/B401 MX-FXX3 (FACSIMILE EXPANSION KIT) 4 – 1

2) Hang the FAX unit on the step screw. Fix the FAX unit with the screws which were removed in the step 1).

3) Remove the screw, and remove the controller cover.

C. FAX memory installation

1) Open the front cover and the tray 1.

4) Install the FAX memory (included in the package) to the slot E for an option of the MFPC PWB.

2) Remove the stopper, and slide the left cabinet to the front side to remove.

D. I/F cable connection

1) Connect the I/F cable to the FAX unit of the MFPC PWB.

Attach the clamp (included in the package) and pass the I/F cable through the clamp.

NOTE: Check to confirm that the connector is not inserted obliquely.

MX-B381/B401 MX-FXX3 (FACSIMILE EXPANSION KIT) 4 – 2

2) Cut off the notch section of the rear cabinet. Attach the I/F cable to the rear cabinet and the frame, and fix the banding band with the screw (M3) (included in the package).

E. Turn on the power of the main unit

1) Insert the power plug into the power outlet.

2) Turn ON the power switch.

3) Attach the controller cover, and fix it with the screw.

3) Turn ON the power switch on the operation panel.

4) Attach the left cabinet by using care for the hook, and fix the stopper.

5) Close the front cover and the tray 1.

F. Set the destination and the logo type.

1) Switch the operation panel to the copy mode and use the key operation [P], [  ], [C], and [  ] to enter the simulation mode.

2) Use the numeric keys to enter [26] in the main code entry screen shown below and press the [START] key.

T ES T

SIMULATION

INPUT A MAIN NUM BY 10-KEY, AND PRESS START

01: SCANNER CHECK

02: SPF CHECK

03: AFTER PROCESS CHECK

04: DESK/LCC CHECK

05: PANEL/LAMP CHECK

06: MFP CHECK

07: AGING

1/9

MX-B381/B401 MX-FXX3 (FACSIMILE EXPANSION KIT) 4 – 3

3) Use the numeric keys to enter [06] in the sub-code entry screen shown below and press the [START] key.

T ES T

SIMULATION NO .

INPUT A SUB NUM BY 10-KEY, AND PRESS START

01: RIGHT TRAY SETUP

02: SI Z E SETUP

03: AUDITOR SETUP

06: DESTINATION SETUP

10: NET W ORK SCANNER TRIAL MODE SETUP

1 8 : TONER SA V E MODE SETUP

30: CE MARK CONTROL SETTING

0 6

1/3

4) Press the desired destination on the touch panel and press

[EXECUTE] to highlight it.

T ES T

SIMULATION NO .

26-06

DESTINATION SETUP

01: U .

S .

A .

02: CANADA 03:

05:

09:

AB _ B

AB _ A

06:

10:

EUROPE

CHINA

07:

INCH

U .

K .

04:

0 8 :

J APAN

AUS .

E X ECUTE

1/1

5) Press the [CA] key or the [SYSTEM SETTINGS] key to exit from the simulation mode. The message [PLEASE TURN

MAIN POWER OFF THEN ON] is displayed.

Restart the machine to change the destination.

• List of destinations

Display

01: U.S.A

U.S.A.

02: CANADA Canada

03: INCH

04: JAPAN

Description

Inch system, other destinations

Japan

05: AB_B AB system (B5 size detectable), other destinations

06: EUROPE Europe

07: U.K.

08: AUS.

U.K.

Australia

09: AB_A

10: CHINA

AB system (A5 size detectable), other destinations

China

G. Clear the FAX related software switches.

1) Switch the operation panel to the copy mode and use the key operation [P], [  ], [C], and [  ] to enter the simulation mode.

2) Use the numeric keys to enter [66] in the main code entry screen shown below and press the [START] key.

T ES T

SIMULATION

INPUT A MAIN NUM BY 10-KEY, AND PRESS START

01: SCANNER CHECK

02: SPF CHECK

03: AFTER PROCESS CHECK

04: DESK/LCC CHECK

05: PANEL/LAMP CHECK

06: MFP CHECK

07: AGING

1/9

3) Use the numeric keys to enter [02] in the sub-code entry screen shown below and press the [START] key.

T ES T

SIMULATION NO .

INPUT A SUB NUM BY 10-KEY, AND PRESS START

01: FA X SOFT S W .

SETTING .

02: FA X SOFT S W .

CLEAR .

03: FA X P W B MEMORY CHECK .

04: SIGNAL OUTPUT CHECK .

( LE V EL MA X)

05: SIGNAL OUTPUT CHECK . ( SOFT S W.)

06: PASS CODE PRINT OUT .

07: IMAGE MEMORY PRINT OUT .

0 2

1/5

4) Use numeric keys [0] and [1] to enter the desired 8-digit country code.

After entry, press [SET], [EXECUTE], and [YES] in this order.

T ES T

SIMULATION NO .

66-02

FA X SOFT S W.

CLEAR - U .

S .

A .

PRESENT:

NE W :

10110101

SET

DEST CODE SURE ?

YES NO E X ECUTE

JAPAN

U.S.A.

AUSTRALIA

U.K.

FRANCE

GERMANY

SWEDEN

NEWZEALAND

CHINA

SINGAPORE

MIDDLEAND

NEAREAST

SLOVAKIA

OTHER3

FINLAND

NORWAY

DENMARK

NETHERLANDS

ITALY

• Country code list screen

* Press the [DEST CODE] button on the initial screen to move to the country code list screen.

To return to the input screen, press the [BACK] button.

T ES T

SIMULATION NO .

66-02 CLOSE

FA X SOFT S W.

CLEAR - U .

S .

A .

J APAN :00000000

AUSTRALIA :00001001

FRANCE :00111101

S W EDEN :10100101

U .

S .

A .

U .

K .

:10110101

:10110100

GERMANY :00000100

NE W Z EALAND :01111110

BACK

1/5

Country code list

: 00000000 SWITZERLAND : 10100110

: 10110101

: 00001001

: 10110100

: 00111101

AUSTRIA

INDONESIA

THAILAND

MALAYSIA

: 00001010

: 01010100

: 10101001

: 01101100

: 00000100

: 10100101

: 01111110

: 00100110

: 10011100

: 11111110

: 11111101

INDIA

PHILIPPINES

HONGKONG

RUSSIA

: 01010011

: 10001001

: 01010000

: 10111000

SOUTHAFRICA : 10011111

SPAIN

PORTUGUESE

: 10100000

: 10001011

: 11111100

: 11111011

: 00111100

: 10000010

: 00110001

: 01111011

: 01011001

LUXEMBURG

BELGIUM

CZECH

HUNGARY

: 01101001

: 00001111

: 00101110

: 01010001

GREECE

POLAND

: 01000110

: 10001010

BRAZIL : 00010110

MX-B381/B401 MX-FXX3 (FACSIMILE EXPANSION KIT) 4 – 4

H. Clear the image memory.

1) Switch the operation panel to the copy mode and use the key operation [P], [  ], [C], and [  ] to enter the simulation mode.

2) Use the numeric keys to enter [66] in the main code entry screen shown below and press the [START] key.

T ES T

SIMULATION

INPUT A MAIN NUM BY 10-KEY, AND PRESS START

01: SCANNER CHECK

02: SPF CHECK

03: AFTER PROCESS CHECK

04: DESK/LCC CHECK

05: PANEL/LAMP CHECK

06: MFP CHECK

07: AGING

1/9

3) Use the numeric keys to enter [10] in the sub-code entry screen shown below and press the [START] key.

T ES T

SIMULATION NO .

INPUT A SUB NUM BY 10-KEY, AND PRESS START

01: FA X SOFT S W.

SETTING .

02: FA X SOFT S W.

CLEAR .

03: FA X P W B MEMORY CHECK .

04: SIGNAL OUTPUT CHECK .

( LE V EL MA X )

05: SIGNAL OUTPUT CHECK .

( SOFT S W.

)

06: PASS CODE PRINT OUT .

07: IMAGE MEMORY PRINT OUT .

1/5

4) In the sub menu screen shown below, press [EXECUTE] on the touch panel.

After [YES] on the panel lights up, press it.

T ES T

SIMULATION NO

IMAGE MEMORY CLEAR .

66-10

SURE ?

YES NO E X ECUTE

5) The screen shown below is displayed and memory clear operation is executed.

T ES T

SIMULATION NO .

66-10

IMAGE MEMORY CLEAR .

I. Line cable connection

1) Connect the line cable on the line to the modular jack indicated as "LINE."

* When an external telephone is used, wind the line cable around the ferrite core (included in the package) two turns, and connect it to the modular jack indicated as "TEL."

App roximately

10 cm

* After connection, perform the setting of "External telephone connection" of the system setting (administrator).

J. Installation completion check

1) Execute SIM 22-10 to check to confirm that the FAX box and the FAX memory are properly installed.

When the FAX1 is properly connected, "MX-FXX3" is displayed.

When the FAX memory is properly connected, "AR-MM9" is displayed.

T ES T

SIMULATION NO

MACHINE SYSTEM

MACHINE : M X -B401

SPF

DESK

: STANDARD

: M X -CS X 1

FINISHER : M X -FN12

FA X 1 : M X -F XX 3

22-10

FA X MEMORY

X PS

SECURITY

AIMY

: AR-MM9

: M X -PK X 5

: M X -PU X 1

: M X -FR16U

: M X -AM X 1

1/2

SURE ?

YES NO E X ECUTE

6) After several minutes, memory clear operation is completed and the [YES] button goes out. Press the [CA] key to exit from the simulation mode.

Then the main unit is automatically rebooted.

MX-B381/B401 MX-FXX3 (FACSIMILE EXPANSION KIT) 4 – 5

1. Unpacking

A. Check the packed items

A R -PF1 barcode font R O M P W B

1 2

No.

Packed part names

CD-ROM

Operation Manual

Bar code Font ROM

2. Installation

A. Turn off the power of the main unit

1) Turn OFF the power switch on the operation panel.

Quantity

B. MFP PWB cover removal

1) Open the front cover and the paper feed tray 1.

2) Remove the stopper, slide the left cabinet to the front side and remove.

2) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch.

3) Remove the screw, and remove the MFP PWB cover.

MX-B381/B401 AR-PF1 (BARCODE FONT KIT) 5 – 1

C. Bar code Font ROM installation

1) Install the Bar code Font ROM.

3) Close the front cover and the tray 1.

D. MFP PWB cover installation

1) Install the MFP PWB cover.

E. Turn on the power of the main unit

1) Insert the power plug into the power outlet.

2) Turn ON the power switch.

2) Install the left cabinet.

3) Turn ON the power switch on the operation panel.

MX-B381/B401 AR-PF1 (BARCODE FONT KIT) 5 – 2

F. PCL expansion font list check

1) PCL expansion font list check

Select the PCL expansion font list by the procedures described in the printer test page in the system setup guide.

Check to confirm that the bar code font list is printed.

Font No.

Font name

Code128TT-Regular

Code128-NarrowTT-Regular

Code128-WideTT-Regular

Code39HalfInch-Regular

Code39OneInch-Regular

Code39QuarterInch-Regular

Code39SmallHigh-Regular

Code39Slim-Regular

Code39SmallLow-Regular

Code39SmallMedium-Regular

Code39Wide-Regular

Codabar-Regular

Interleaved2of5-Regular

Interleaved2of5-Thin-Regular

OCR-A

OCR-B

OCR-B-C39-Regular

UPC-Half

UPC-Half-Bars

UPC-HalfMusic

UPC-HalfNarrow

UPC-HalfThin

UPC-Tall-Regular

UPC-TallBarsThin-regular

UPC-TallMusicThin-Regular

UPC-TallNarrow-Regular

UPC-TallThin-regular

ZipCodeBarcode-Regular

MX-B381/B401 AR-PF1 (BARCODE FONT KIT) 5 – 3

1. Unpacking

A. Check the packed items

1) Check to confirm that all the parts are included in the package.

Service Manual

2) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch.

No.

3 4

Packed part names

PROGRAM ROM 1

PROGRAM ROM 2

Operation manual

USB memory (with the program data in it)

Quantity

2. Installation

<Note before installation>

• To enable the data security function, the product key must be acquired. (For the acquisition procedures of the product key, inquire the distributor.)

• Before installing the data security kit, be sure to back up the data stored in the memory (including the HDD) of the machine.

When the data security kit is installed, all the job data stored in the memory (including the HDD) of the machine are deleted.

• When the printer lamp and the image send communication lamp and the data lamp on the operation panel are lighted or blinking, unprocessed data remain in the memory (including the HDD) of the machine. In this case, perform all the output/send operations so that no data remain in the machine, then perform installation.

(Check to confirm that the communication lamp on the operation panel and the data lamp under it are not lighted and not blinking.)

A. Turn off the power of the main unit

1) Turn OFF the power switch on the operation panel.

3) Disconnect the power plug from the power outlet.

B. MFP PWB cover removal

1) Open the front cover and the paper feed tray 1.

2) Remove the stopper, and shift the left cabinet to the front side to remove.

MX-B381/B401 MX-FR16U (DATA SECURITY KIT) 6 – 1

3) Remove the screw, and remove the MFP PWB cover.

2) Install the left cabinet.

C. ROM replacement

1) Replace the ROM. (Install the accessory DSK ROM.)

3) Close the front cover and the tray 1.

D. MFP PWB cover installation

1) Install the MFP PWB cover.

E. DSK firmware installation

1) Insert the accessory USB memory into the USB slot of the machine. (Use the USB I/F of the operation panel.)

2) When the power is turned ON, the main program error is displayed.

M ain Program Error !!

3) The above error message is displayed for 10 sec. Then the following message is displayed.

Emergency Prog Init

Please w ait

4) The machine enters the boot mode which indicates that there is an error in the main program.

V ersion Check

Ic M:UNU S U A L

MX-B381/B401 MX-FR16U (DATA SECURITY KIT) 6 – 2

(1) Operations in the boot mode

When the machine is booted in the boot mode, the firmware version check, the firmware install, and the version-up operation can be performed.

When a HDD is installed to the machine and the above operation is performed, the firmware must be installed.

* In the boot mode, the following keys are used for operation. Note that the functions of the keys in the boot mode differ from those in the normal mode.

a. Key functions and operations in the boot mode

UP key DOWN key BACK key

JOB STATUS

SYSTEM

SETTINGS

PRINT

IMAGE SEND

READY

DATA

LINE

DATA

HOME

LOGOUT

Key name in the normal mode

Start key

Home key

Clear key

Job status key

System setting key

Key name in the boot mode

[OK] key

[MENU] key

[BACK] key

[UP] key

[DOWN] key

MENU key OK key

Function

Performs the selected item or function.

Selects a menu.

Selects a menu. (Serves as a cancel key in the execution check screen.)

Selects an item.

(2) Functions in the boot mode

The following two functions are available in the boot mode.

Function

Firmware version check function

Firmware install (update) function

Content

Displays the firmware version of the ICU PWB, the SCU PWB, the PCU PWB, and the FAC PWB.

Installs (revises) the firmware by transmitting data from the PC which is connected to the ICU PWB, the SCU PWB, the

PCU PWB, the FAX PWB, and other options with the USB memory or the USB cable.

a. Selection of functions in the boot mode

There are two functions available in the boot mode. These modes can be selected by pressing MENU key and BACK key.

2) Insert the USB memory which includes the update firmware file

(SFU file) into the USB port of the machine, and press [OK] key.

M E NU key

V ersion Check

Ic M:UNU S U A L

Firm U pdate

From U SB M emory

Firm U pdate

From U SB M emory

BAC K key

BAC K key b. Firmware install and version-up procedures in the boot mode

1) Boot the machine in the boot mode. When the Version Check display is indicated, press [MENU] key, and the machine enters the Firm Update mode.

Firm U pdate

> 0100P 2 00 .

sfu

SFU file display

3) Select the firmware file (SFU file) of the target.

Use [UP] key and [DOWN] key to select the target file.

When [OK] key is pressed with the directory name displayed, the control can enter the lower level directory. (However, onestep lower level)

When [BACK] key is pressed in the lower level directory, the control can return to the upper level directory.

4) Press [OK] key.

The selected firmware file (SFU) is read. (It takes about 1 minute.)

Firm U pdate

R eading Data

Display of reading file data

MX-B381/B401 MX-FR16U (DATA SECURITY KIT) 6 – 3

5) After completion of reading, the firmware is installed (updated).

(It takes about 5 - 6 minutes.)

Firm

Icu M

U pdate

Display of firmware install (Update) process

* The abbreviated name of the firmware which is currently installed (updated) is displayed sequentially.

* The screen may flash instantaneously during the install

(update) process. This is a normal operation.

6) Check the result of install (update) of the firmware.

Use [UP] key and [DOWN] key to check the results of install

(update) of all the firmware programs.

Firm

Icu M

U pdat Firm

Icu M

U pdat Firm

Icu M

U pdat

Display of firmware update results

OK: Update success

NG: Update failed

Not Update: The update process is not executed.

Cause of Update process not executed:

The option unit for the target firmware is not connected.

7) Turn OFF the power to terminate the boot mode.

8) Use SIM22-05 to check to confirm that the DSK firmware has been installed.

F. Preparation for validating the DSK

1) To validate the DSK, enter the product key by the key operation on the machine.

a) Press the [SYSTEM SETTINGS] key on the operation panel.

b) Enter page 2/2 of the system setting, and touch [Product key input] key.

c) Touch [Data security kit] key.

d) Enter the product key with numeric key (10-key), and touch [Registration] key.

2) When inputting the product key is completed, check to confirm that "Turn on the power again" is displayed, and turn OFF the power switch and the main power switch, and then turn ON them again.

MX-B381/B401 MX-FR16U (DATA SECURITY KIT) 6 – 4

1. Unpacking

A. Check the packed items

No.

1 2

Packed part names

CD-ROM

Product key sheet

Quantity

2. Installation

<Note before installation>

• In order to enable the Internet Fax send function, the product key must be acquired.

• In order to specify the address of the Internet Fax with the PC-

FAX driver, the PC-FAX driver must be updated by the Internet

Fax expansion kit.

A. Preparation for enabling the Internet Fax send function

1) In order to enable the Internet Fax send function, enter the product key by the key operation on the operation panel.

a) Press the system setting key on the operation panel.

b) Select page 2/2 of the system setting, and touch [Product key input] key.

c) Touch [Internet Fax expansion kit] key.

d) Enter the product key with numeric key (10-key), and touch [Registration] key.

2) After completion of entry of the product key, turn OFF the power switch on the operation panel. Turn OFF the main power switch, then turn ON the power switch and the main power switch again.

* After completion of 1) and 2), the Internet Fax send function from the main unit becomes enable. To enable the Internet

Fax send with the PC-FAX driver, the following steps 3) and

4) are required.

3) Use the CD-ROM packed together with the machine to install the PC-FAX driver.

For installing procedures, refer to the software setup guide.

4) Update the PC-FAX driver with the CD-ROM packed together with the machine.

* Install and setting of the driver to the PC server must be performed by the user or by the request from the user.

B. Operation check of the Internet Fax send function

1) After completion of entry of the product key, check to confirm that the Internet Fax send is performed normally from the machine.

2) After completion of update of the PC-FAX driver, press the print button on the test page of the PC-FAX driver to check to confirm that the Internet Fax send is performed normally.

MX-B381/B401 MX-FWX1 (INTERNET FAX EXPANSION KIT) 7 – 1

1. Unpacking

A. Check the packed items

1 2

No.

Packed part names

CD-ROM

Operation manual

Quantity

2. Installation

<Note before installation>

To enable XPS, an expansion memory (MX-SMX3) must be installed.

To install an expansion memory, refer to the descriptions of "[12]

MX-SMX3" on this manual.

A. Preparation for enabling XPS

1) To enable XPS, enter the product key by the key operation of the copier machine.

a) Press the system setting key on the operation panel.

b) Select page 2/2 of the system setting, and touch [Product key input] key.

c) Touch [XPS expansion kit] key.

d) Enter the product key with numeric key (10-key), and touch [Registration] key.

2) After completion of entry of the product key, turn OFF the power switch on the operation panel. Turn OFF the main power switch, then turn ON the power switch and the main power switch again.

3) Use the CD-ROM packed together with the machine to install the XPS driver.

For installing procedures, refer to the software setup guide.

Installation of the driver must be performed by the user or the serviceman with assistance or the user.

Please keep below important information.

This information will use for other products.

Service Manual

APPLICATION

NUMBER

MACHINE

SERIAL

NUMBER

PRODUCT

KEY

MX-B381/B401 MX-PUX1 (XPS EXPANSION KIT) 8 – 1

INTEGRATION MODULE)

1. Unpacking

A. Check the packed items

1 2 3

No.

Packed part names

CD-ROM

MX-AMX1 GETTING STARTED GUIDE

Sharpdesk license kit Operation Manual

Quantity

2. Installation

<Note before installation>

To enable the Application Integration Module function, the product key must be acquired.

A. Make preparations to enable the Application

Integration Module function.

1) To enable the Application Integration Module function, enter the product key by the key operation of the operation panel.

a) Press the system setting key on the operation panel.

b) Select page 2/2 of the system setting, and touch [Product key input] key.

c) Touch [Application expansion kit] key.

d) Enter the product key with numeric key (10-key), and touch [Registration] key.

2) After entering the product key information, turn OFF the power switch and the main power switch of the machine, and turn them ON again. (For the models with the main power switch only, turn OFF/ON the main power switch only.)

B. Check the operation of the Application

Integration Module function.

1) Send image data and meta data by referring to MX-AMX1

GETTING STARTED GUIDE (included in package). Check to confirm that image data and meta data are properly received.

Service Manual

MX-B381/B401 MX-AMX1 (APPLICATION INTEGRATION MODULE) 9 – 1

COMMUNICATION MODULE)

1. Unpacking

A. Check the packed items

Service Manual played.

1 2

No.

Packed part names

CD-ROM

Operation manual

Quantity

2. Installation

<Note before installation>

* To enable the external account kit, the product key must be acquired.

A. Make preparations for enabling the Application

Communication Module

To enable the Application Communication Module, enter the product key by key operations on the operation panel.

1) Press the [SYSTEM SETTINGS] key.

2) Touch the [Admin Password] key.

3) Touch the [Password] key and enter the administrator password.

4) Touch the [OK] key.

5) Touch the [Product Key] key.

You may have to scroll down the screen to show this key.

6) Touch the [Application Communication Module] key.

7) Enter the product key with the 10-key, and touch [OK] key.

• The product key can be entered from the Web page.

For details, refer to [HELP] on the right upper side of the Web page.

B. OSA Settings

1) By performing procedure A, "OSA setting" key is added to the menu screen of the system setting or the key operator program.

3) When the [Default Display Setting] key is touched, the screen for setting the default display that appears when the [DOCU-

MENT FILING] key is pressed will appear.

• To set the base screen of document filing as the default display, touch the [Document Filing] key.

• To set the external application selection screen as the default display, touch the [OSA] key.

4) After selecting the setting, touch the [OK] key.

• "Default Display Setting" also appears in "Document Filing

Settings" in the system settings (administrator).

• If the [CA] key is pressed in document filing mode or OSA mode, the base screen of that mode will appear regardless of the default display setting.

C. External application setup

1) Click the [Login] button that appears in the upper right-hand corner of the Web page.

2) Select [Administrator] in [Login Name] and then enter your password.

3) Click [External Applications Setup] in the menu frame.

4) Configure the standard application settings.

• Up to 8 standard applications can be stored.

• For each setting item, refer to [Help].

MX-B381/B401 MX-AMX2 (APPLICATION COMMUNICATION MODULE) 10 – 1

Service Manual displayed.

ACCOUNT MODULE)

1. Unpacking

A. Check the packed items

1 2

No.

Packed part names

CD-ROM

Operation manual

Quantity

2. Installation

<Note before installation>

* To enable the external account kit, the product key must be acquired.

A. Make preparations for enabling the external account kit.

1) To enable the external account kit, enter the product key by key operations on the operation panel.

a) Press [SYSTEM SETTINGS] key.

b) Touch [Administrator Password] key.

c) Touch [Password] key and enter the administrator password.

d) Touch [OK] key.

e) Scroll the screen, and touch [Product Key] key.

f) Touch [External Account Module] key.

g) Enter the product key with 10-key, and touch [OK] key.

• The product key can be entered from the Web page. For details, refer to [HELP] on the right upper side of the Web page.

2) Make the OSA setting.

a) By the procedure of 1), "OSA setting" key is added to the menu screen of the system setting or the key operator program.

c) When [External Account Setting] key is touched, the screen for setting the calculation by the external application and for enabling user authentication is displayed.

(The two settings are linked together.)

• When the check box of [External Account Management is Enabled] is checked:

The result of the job completion is notified to the external application set on the Web page. (The default is

"Disabled.")

• If the check box is OFF, check cannot be made.

• When the check box of [Authentication by the External

Account Application is Enabled] is checked:

When the machine is booted, the login screen can be acquired from the application set on the Web page.

(The default is "Disabled.") d) After setting, when [OK] key on the force account setting screen is touched, the message to urge rebooting of the machine is displayed. To enable the setting, touch [OK] key and reboot the machine.

B. Set the external application.

1) Click [Login] button on the right upper side of the Web page.

2) Select [Administrator] from [Login Name] and enter the password.

3) Click [External Application Setting] on the menu frame.

4) Click [External Account].

5) Set the external account application.

• For each setting item, refer to [HELP]. To enable the setting on the Web page, reboot the machine.

MX-B381/B401 MX-AMX3 (EXTERNAL ACCOUNT MODULE) 11 – 1

1. Unpacking

A. Check the packed items

No.

Packed part name

Expansion memory board

2. Installation

A. Turn off the power of the main unit

1) Turn OFF the power switch on the operation panel.

Quantity

B. Controller cover and left cabinet removal

1) Open the front cover and the tray 1.

2) Remove the stopper, and slide the left cabinet to the front side to remove.

2) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch.

3) Remove the screw, and remove the controller cover.

3) Disconnect the power plug from the power outlet.

MX-B381/B401 MX-SMX3 (EXPANSION MEMORY BOARD) 12 – 1

C. Installation of an expansion memory board

1) Install an expansion memory board to the DIMM2 slot of the

MFPC PWB.

NOTE: Do not push one end of the expansion memory board by one hand.

b) Hold the both ends of the expansion memory board with both hands, and put down the expansion memory so that it is vertical to the PWB.

At that time, check to confirm that the hooks on the left and the right sides of the slot are securely locked.

* Note for installation a) Insert the expansion memory board into the slot diagonally from below.

NOTE: When handling an expansion memory board, be careful not to touch the terminals.

D. Installation of the controller cover and the left cabinet

1) Attach the controller cover, and fix it with the screw.

NOTE: Avoid diagonal insertion of the expansion memory board for the slot.

MX-B381/B401 MX-SMX3 (EXPANSION MEMORY BOARD) 12 – 2

2) Attach the left cabinet by using care for the hook, and fix the stopper.

3) Turn ON the power switch on the operation panel.

3) Close the front cover and the tray 1.

E. Turn on the power of the main unit

1) Insert the power plug into the power outlet.

2) Turn ON the power switch.

MX-B381/B401 MX-SMX3 (EXPANSION MEMORY BOARD) 12 – 3

1. Heater kit contents list

No.

Part Name

Dehumidifier heater unit

Heater switch label EX Pa

"Caution: HOT" label

WH harness

Saddle

Dehumidifier heater switch

WH PWB

PWB Mylar sheet

M3 x 6 screw

WH earth harness 200

M3 x 8 screw

2. Installation

<Note before installation>

Start installation after checking that the LINE indicator and the

DATA indicator below it on the operation panel are neither lit nor blinking.

A. Turn off the power of the main unit

1) Turn OFF the power switch on the operation panel.

DKIT-0416FCZZ

120V series

Part code Qty.

CPLTM7785FC51

TLABZ5256FCZZ

TLABZ5459FCZZ

DHAI-4367FCPZ

LHLDW1970FCPZ

QSW-C9294QCZZ

CPWBF1858FC31

PSHEP0620FCPZ

LSUPP0117FCZZ 3

XHBS730P06000 1

DKIT-0417FCZZ

230V series

Part code Qty.

CPLTM7785FC52

TLABZ5256FCZZ

TLABZ5459FCZZ

DHAI-4367FCPZ

LHLDW1970FCPZ

QSW-C9294QCZZ

CPWBF1858FC32

PSHEP0620FCPZ

LSUPP0117FCZZ 3

LBNDJ0037FCZ1 2

DHAI-4390FCPZ

XBPS730P08KS0

3) Disconnect the power plug from the power outlet.

2) Check to confirm that the operation panel is turned OFF, and then turn OFF the power switch.

B. Remove the rear cabinet of the machine.

1) Remove five screws from the rear cabinet.

2) Release the locks at the bottom.

3) Remove the rear cabinet from the machine.

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MAIN UNIT 13 – 1

C. Install the WH PWB unit.

1) Insert three PWB supporters (No.9) into the paper feed drive unit.

* Insert the lead edge with flange into the metal plate.

2) Insert the PWB Mylar sheet (No.8) into the PWB supporter.

3) Insert the WH PWB (No.7) into the PWB supporter.

Check to confirm that the PWB supporter hook is securely engaged with the WH PWB.

4) Insert the saddle (No.5) into the WH PWB.

F. Install the WH earth harness 200. (200V series only)

1) Remove the protection Mylar from the dehumidifier heater unit.

D. Attach the WH harness (No.4).

1) Attach the WH harness to the wire saddle. (4 positions)

2) Connect the connector. (4 positions).

3) Pass the WH harness under the metal plate and extend it out from the square hole in the metal plate.

2) Install the WH earth harness 200 to the plate of the dehumidifier heater unit with the M3 x 6 screw (No. 10).

In this case, use care so that the terminals of the WH earth harness 200 do not extend from the edges of the plate.

E. Attach the dehumidifier heater switch (No.6).

1) Attach the dehumidifier heater switch to the connector.

* Since there is no designation for polarity, insert into any terminal.

* Insert fully to the bottom until it clicks.

2) Insert the dehumidifier heater switch into the square hole in the metal plate.

* Insert so that the connector connected to the dehumidifier heater switch is on the right side when viewed from the rear.

3) Install the protection Mylar which was removed in the procedure 1).

In this case, pass the harness of the dehumidifier heater unit and the WH earth harness 200 through the square hole of the protection Mylar.

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MAIN UNIT 13 – 2

G. Installation of the dehumidifier heater unit to the main unit.

1) Pull out the paper tray, and pass the harness of the dehumidifier heater through the hole in the upper section of the lift-up unit.

For the 200V series, pass the WH earth harness 200 through the hole in the upper section of the lift-up unit.

2) Engage the pawls of the dehumidifier heater unit with the square holes (4 positions) in the metal plate of the main unit.

3) Fix the dehumidifier heater installation plate FT with the M3 x 6 screw (No.10).

* At that time, arrange so that the rear section of the dehumidifier heater installation plate FT is on the lift-up unit.

2 00 V O nly

6) Pass the WH earth harness 200 through three clamps of the machine. (200V series only)

7) Fix the terminal of the WH earth harness 200 to the machine frame with the M3 x 8 screw (No. 12).

L ift up unit

4) Pass the harness of the dehumidifier heater through the wire saddle.

5) Connect the connector of the dehumidifier heater harness to

CN3 of the WH PWB.

When installing the dehumidifier heater kit to the MX-CSX1/

CSX2, hereinafter perform the operations described on the chapter of "[15] DEHUMIDIFIER HEATER KIT (SERVICE

PARTS) OF THE MX-CSX1/CSX2."

When the MX-CSX1/CSX2 is not installed, or when the MX-

CSX1/CSX2 is installed but the dehumidifier heater kit is not installed to the MX-CSX1/CSX2, perform the procedures from item H below.

H. Dehumidifier heater resistance check

1) Insert a tester between pin 1 and pin 3 of CN3 of the WH PWB, and check to confirm that the resistance is as shown below.

120V series: 2.304K

 - 3.456K



230V series: 4.232K

 - 6.348K



MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MAIN UNIT 13 – 3

I. Addition of the holes for the dehumidifier heater switch

1) Cut off the notch of the square hole for the dehumidifier heater switch on the rear cabinet.

2) Attach the heater switch label EX Pa (No.2) to the concaved section of the rear cabinet.

* Be careful of the attachment direction of the heater switch label EX Pa.

K. Attach the rear cabinet.

3) Cut the inside section of the rear cabinet where the harness passes through.

3. Check after installation

1) Turn ON the dehumidifier heater switch. (Press the upper section of the switch.)

J. High temperature caution label attachment

1) Where the "Caution: HOT" label will be placed. (see illustration). Clean with alcohol.

2) Attach the "Caution: HOT" label to the paper tray.

0 - 0.5mm

2) Measure the resistance between the earth terminal and the AC terminal at the lead edge of the AC cord with a tester, and check to confirm that the resistance is infinite.

* Check the resistance between the non-grounding side (Live) and the grounding side and between the non-grounding side

(Neutral) and the grounding side.

* If there is conduction between the grounding terminal and the AC terminal, the harness on the primary side may be in contact with the grounding wire (the wire may be pinched or in some trouble). In this case, disassemble it again and check to confirm that there is no pinching or wiring mistake.

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MAIN UNIT 13 – 4

CSX2

1. Heater kit contents list

No.

Part Name

Desk dehumidifier heater unit

PWB supporter (KGLS-3S)

Mini clamp (UAMS-07-0)

Heater interface PWB

M4 x 10P tight screw

WH desk I/F harness

WH Frontier I/F harness

Snap band

DKIT-0418FCZZ

120V series

Part code

CHLDZ2043FC51

LBSHZ2029SCZZ

LHLDW0734FCZZ

CPWBF1862FC31

XEBS740P10000

DHAI-4383FCPZ

DHAI-4382FCPZ

LBNDJ0043FCZ1

2. Installation

<Note before installation>

• Confirm that the line and data indicator (below) on the operation panel are not lite or blinking. Then turn off machine.

• The dehumidifier heater kit for the MX-CSX1/CSX2 cannot be installed without the main unit dehumidifier kit.

Be sure to install the dehumidifier heater kit for the main unit first, and then install the dehumidifier heater kit for the MX-CSX1/

CSX2.

• After completion of the procedure in item G of the installation procedures of the dehumidifier heater kit for the main unit, perform the following procedures.

A. Desk cabinet removal

* The descriptions are made on the MX-CSX1. If the MX-CSX2 is also installed, perform the same procedures for the MX-CSX2.

1) Pull out the paper tray, and loosen the hand screw which is on the left side when viewed from the front.

Qty.

DKIT-0419FCZZ

127V series

Part code

CHLDZ2043FC52

LBSHZ2029SCZZ

LHLDW0734FCZZ

CPWBF1862FC31

XEBS740P10000

DHAI-4383FCPZ

DHAI-4382FCPZ

LBNDJ0043FCZ1

Qty.

DKIT-0420FCZZ

230V series

Part code

CHLDZ2043FC53

LBSHZ2029SCZZ

LHLDW0734FCZZ

CPWBF1862FC31

XEBS740P10000

DHAI-4383FCPZ

DHAI-4382FCPZ

LBNDJ0043FCZ1

Qty.

2) Slide the desk left cabinet to the front side.

3) Remove a screw.

4) Open the desk right side cabinet.

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MX-CSX1/CSX2 14 – 1

5) Press the right side (left side when viewed from the rear) of the desk rear cabinet and pull the rear cabinet to the rear.

3) Attach the mini clamp (No.3) to the MX-CSX1.

4) Insert the snap band attached to the WH Frontier I/F harness into the MX-CSX1.

5) Hang the WH Frontier I/F harness on the notch section of the cabinet of the MX-CSX1.

B. Heater interface PWB installation

* The descriptions are made on the MX-CSX1. If the MX-CSX2 is also installed, perform the same procedures for the MX-CSX2.

1) Insert the PWB supporter (No.2) into the left side of the desk.

(4 positions)

* Insert the edge with flange into the desk.

2) Insert the heater Interface PWB (No.4) into the PWB supporter.

6) Pass the WH Frontier I/F harness to the saddle.

7) Connect the WH Frontier I/F harness connector to CN4 of the

WH PWB of the main unit.

C. Connect the main unit and the MX-CSX1.

* This procedure is required only for the MX-CSX1, and is not required for the MX-CSX2.

* When only the MX-CSX1 is installed, the WH desk I/F harness

(No.6) is not used.

1) Pass the red connector side of the WH Frontier I/F harness

(No.7) through the clearance shown in the figure below to the heater interface PWB on the left side.

2) Connect the WH Frontier I/F harness (No.7) to CN-A of the heater interface PWB (No.4).

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MX-CSX1/CSX2 14 – 2

D. Install the desk dehumidifier heater unit to the

MX-CSX1.

* The descriptions are made on the MX-CSX1. If the MX-CSX2 is also installed, perform the same procedures for the MX-CSX2.

1) Pass the desk dehumidifier heater harness through the MX-

CSX1 to the rear side.

2) Attach the desk dehumidifier heater to the upper side of the

MX-CSX1, and fix it with the M4 x 10P tight screw (No.5).

E. Connection with the MX-CSX1 and the MX-

CSX2 (Connection of the first stage and the second stage, and connection of the second stage and the third stage)

* The WH Frontier I/F harness is not used.

* When the MX-CSX2 is not installed, this procedure is not required.

The connection procedures are described on connection between the MX-CSX1 and the MX-CSX2. When two units of the MX-CSX2 are installed, first connect the MX-CSX1 and the MX-CSX2, then connect the MX-CSX2 (upper stage) and the MX-CSX2 (lower stage).

1) Pass the white connector of the WH desk I/F harness (No.6) through the square hole in the MX-CSX1 to the heater interface PWB side.

2) Pass the red connector of the WH desk I/F harness through the square hole in the MX-CSX2 to the heater interface PWB side.

3) Hang the harness on the notch of the cabinet of the MX-CSX1.

3 )

3) Pass the desk dehumidifier heater harness through the mini clamp. (2 positions)

4) Pass the desk dehumidifier heater harness through the 500 hole of the desk dehumidifier heater similarly with C-1).

2 )

4) Insert the white connector of the WH desk I/F harness into CN-

C of the heater interface PWB of the MX-CSX1.

5) Insert the red connector of the WH desk I/F harness into CN-A of the heater interface PWB of the MX-CSX2.

4 )

5) Insert the connector of the desk dehumidifier heater harness into CN-B of the heater interface PWB.

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MX-CSX1/CSX2 14 – 3

6) Bind the desk dehumidifier heater harness and the WH desk I/

F harness with the snap band, and insert them into the round hole in the 500-sheet paper feed unit.

Cut the lead edge of the snap band with about 5mm edge left.

H. Desk fixing

1) Return the lock plate which is on the left side when viewed from the machine front to the original position, and tighten the hand screw.

F. Dehumidifier heater resistance check

1) Insert a tester between pin 1 and pin 3 of CN3 of the WH PWB of the main unit, and check to confirm that the resistance is as shown below.

When one MX-CSX1 is installed:

When one MX-CSX1 and one MX-CSX2 are installed:

When one MX-CSX1 and two MX-CSX2 are installed:

120V series 127V series 230V series

1047 -

1571 

1112 -

1668 

678 - 1016  733 - 1100 

501 - 751 

2013 -

3020 

1321 -

1981 

547 - 820  983 - 1474 

Though the MX-CSX2 is installed, if the dehumidifier heater kit is installed only to the MX-CSX1, the measurement value is that "When one MX-CSX1 is installed."

2) Fix the lock plate with the M4 x 10 P tight screws. (3 positions)

* This screw is installed so that the end user cannot remove the MX-CSX1/CSX2 easily. Be careful not to forget installation of this screw.

G. Install the desk cabinet in the reversed sequence of item A.

1) Install the desk cabinet and tighten the screw.

* Use enough care not to pinch the harness.

When the dehumidifier heater kit for the 500 paper feed unit is installed to the machine with the dehumidifier heater kit installed in advance, the procedure of I and J are not required.

I. Addition of the holes for the dehumidifier heater switch

1) Cut off the notch of the square hole for the dehumidifier heater switch on the rear cabinet.

2) Attach the heater switch label (No.2) (which is packed together with the dehumidifier heater kit for the machine) to the concaved section of the rear cabinet.

* Be careful of the attachment direction of the heater switch label.

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MX-CSX1/CSX2 14 – 4

K. Attach the rear cabinet.

3) Cut the inside section of the rear cabinet where the harness passes through.

3. Check after installation

1) Turn ON the dehumidifier heater switch. (Press the upper section of the switch.)

J. High temperature caution label attachment

1) Pull out the paper tray 1, and clean the caution label attachment section with alcohol.

2) Attach the caution label (which is packed together with the dehumidifier heater kit for the main unit) to the paper tray.

0 - 0.5mm

2) Measure the resistance between the earth terminal and the AC terminal at the lead edge of the AC cord with a tester, and check to confirm that the resistance is infinite.

* Check the resistance between the non-grounding side (Live) and the grounding side and between the non-grounding side

(Neutral) and the grounding side.

MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MX-CSX1/CSX2 14 – 5

LEAD-FREE SOLDER

T he P W B ’ s of this model employs lead-free solder . T he “L F ” marks indicated on the P W B ’ s and the Service M anual mean “L ead-Free ” solder .

T he alphabet follo w ing the L F mark sho w s the kind of lead-free solder .

Example:

5mm

L ead-Free

Solder composition code ( R efer to the table at the right .

) a

<Solder composition code of lead-free solder>

Solder composition

Sn-Ag-Cu

Sn-Ag-Bi

Sn-Ag-Bi-Cu

SnZ n-Bi

Sn-In-Ag-Bi

Sn-CuN i

Sn-Ag-Sb

Bi-Sn-Ag-P

Bi-Sn-Ag

Solder composition code a i b z n s p

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

W hen repairing a lead-free solder P W B , use lead-free solder thread .

N ever use conventional lead solder thread , w hich may cause a breakdo w n or an accident .

Since the melting-point of lead-free solder thread is about 4 0 ° C higher than that of conventional lead solder thread , the use of the exclusive-use soldering iron is recommended .

(2) NOTE FOR SOLDERING WORK

COPYRIGHT

0 °

©

XXXX BYSHARP CORPORATION

, and its soldering capacity is inferior to conventional one , it is apt to keep the soldering iron in contact w ith the P W B for longer time . T his may cause land

W B w hen completion of soldering is confirmed .

Since lead-free solder includes a greater q uantity of tin , the iron tip may corrode easily . T urn ON/O FF the soldering iron po w er fre q uently .

If different-kind solder remains on the soldering iron tip , it is melted together w ith lead-free solder . T o avoid this , clean the soldering iron tip after completion of soldering w ork .

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in

If the soldering iron tip is discolored black during soldering w ork , clean and file the tip w ith steel w ool or a fine filer .

any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

C AUTION FOR B ATTER Y RE P LA C E M ENT

(Danish) AD V A R SE L !

L ithiumbatteri – Eksplosionsfare ved fe j lagtig h å ndtering .

U dskiftning m å kun ske med batteri af samme fabrikat og type .

L ev é r det brugte batteri tilbage til leverandoren .

(English) Caution !

Danger of explosion if battery is incorrectly replaced .

R eplace only w ith the same or e q uivalent type recommended by the manufacturer .

Dispose of used batteries according to manufacturer ’ s instructions .

(Finnish) V A RO I TU S

Paristo voi r äjä ht ää, j os se on virheellisesti asennettu .

V aihda paristo ainoastaan laitevalmista j an suosittelemaan tyyppiin . Hä vit ä k ä ytetty paristo valmista j an oh j eiden mukaisesti .

(French) A TT E NT I ON

Il y a danger d ’ explosion s ’ il y a remplacement incorrect de la batterie . R emplacer uni q uement avec une batterie du m ê me type ou d ’ un type éq uivalent recommand é par le constructeur .

M ettre au rebut les batteries usag é es conform é ment aux instructions du fabricant .

(S w edish) V A RN I NG

Explosionsfara vid felaktigt batteribyte .

Anv ä nd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren .

K assera anv ä nt batteri enligt fabrikantens instruktion .

( G erman) Achtung

Explosionsgefahr bei V er w endung inkorrekter Batterien .

Als Ersat z batterien d ü rfen nur Batterien vom gleichen T yp oder vom H ersteller empfohlene Batterien ver w endet w erden .

Entsorgung der gebrauchten Batterien nur nach den vom

H ersteller angegebenen An w eisungen .

C AUTION FOR B ATTER Y DIS P OSAL

(For U SA , CA N ADA)

“ BA TT E RY DISP O SA L”

TH IS P RO D U C T C ONT AI N S A L I TH I UM P R I M A RY

( M A NG A N ESS DI O XIDE) M E MORY BAC K U P BA TT E RY

TH A T MU S T BE DISP O SED O F P RO PE RLY. R E MOV E TH E

BA TT E RY F ROM TH E P RO D U C T A N D C ONT AC T YOUR

LO CA L E NV I RONM E NT A L A G E N CIES F OR I N F ORM A T I ON

ON R EC Y C L I NG A N D DISP O SA L O P T I ON S .

“TR AI T E M E NT DES PI L ES U SA GÉ ES ”

CE P RO D U I T C ONT IE NT UN E PI L E DE SA UV E G A R DE DE

MÉMO I R E L I TH I UM P R I M AI R E (DI O X Y DE DE M A NG A NÈ SE)

QU I D O I T ÊTR E TR AI TÉ E C ORR EC T E M E NT.

E NL E V E Z L A

PI L E D U P RO D U I T E T P R E N E Z C ONT AC T A V EC VOTR E

A G E N CE E NV I RONN E M E NT A L E LO CA L E P OUR DES

I N F ORM A T I ON S S UR L ES MÉTHO DES DE R EC Y C L A G E E T

DE TR AI T E M E NT.

Produced in Japan for electronic Distribution

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher.

Trademark acknowledgements

• Microsoft ® , Windows ® , Windows ® 98, Windows ® Me, Windows NT ® 4.0,

Windows ® 2000, Windows ® XP, Windows ® Vista, Windows ® Server 2003 and

Internet Explorer ® are registered trademarks or trademarks of

Microsoft Corporation in the U.S.A. and other countries.

• PostScript is a registered trademark of Adobe Systems Incorporated.

• Macintosh, Mac OS, AppleTalk, EtherTalk, Laser Writer, and Safari are registered trademarks or trademarks of Apple Computer, Inc.

• IBM, PC/AT, and Power PC are trademarks of International Business Machines

Corporation.

Adobe Systems Incorporated.

• PCL is a registered trademark of the Hewlett-Packard Company.

• Sharpdesk is a trademark of Sharp Corporation.

• All other trademarks and copyrights are the property of their respective owners.

SHARP CORPORATION

Business Solutions Group

CS Promotion Center

Yamatokoriyama, Nara 639-1186, Japan

2009 August Produced in Japan for electronic Distribution

Hello! I am an AI chatbot specifically trained to assist you with the Sharp MX-B401 Installation manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

INSTALLATION MANUAL

DIGITAL MULTIFUNCTIONAL

SYSTEM

MODEL

MX-B381

MX-B401

CONTENTS

SHARP CORPORATION

CONTENTS

1. System configuration

2. Machine configuration

3. Option list

A. Bringing space

B. Installing space

D. Floor strength and level

C. Power source (Capacity, voltage, frequency, safety, plug)

E. Direct rays of the sun, dust, temperature, humidity, gasses, chemicals, vibration

A. Implements, facility, and manpower

B. Delivery

A. Unpacking procedure

C. Check the packed items

A. Installation of the developer cartridges

B. Removal of the fixing tape and protection material

B. Cleaning of LSU's dust-proof glass

C. Installation of the operation manual pocket

D. Tray size setup

E. Installation of toner cartridges

F. Specifications setting

G. Image off-center adjustment

H. Remote operation panel function Enable setting

J. USB PORT selection

I. Functional operation check

K. Storing setting and adjustment data

L. Procedures required for transit of the machine

A. Removal of the 500 sheet paper feed unit

A. Turn off the power of the main unit

B. Removal of the fixing tape and protection material

B. Install the MX-CSX1 or the MX-CSX2 to the MX-

CSX2.

C. Install the main unit to the MX-CSX1.

D. Turn on the power of the main unit

A. Image off-center automatic adjustment

(Document table mode)

A. Removal of the finisher

A. Turn off the power of the main unit

B. Removal of the fixing tape and protection material

C. Check the packed items

B. Installation of the machine connection unit

C. Installation of the finisher

D. Installation of the paper exit tray

F. I/F cable connection

E. Staple position label attachment

G. Turn on the power of the main unit

B. Paper delivery roller descending position adjustment

A. Paper alignment width adjustment

A. Check the packed items

A. Turn off the power of the main unit

B. FAX unit installation

C. FAX memory installation

D. I/F cable connection

E. Turn on the power of the main unit

F. Set the destination and the logo type.

G. Clear the FAX related software switches.

H. Clear the image memory.

I. Line cable connection

J. Installation completion check

A. Check the packed items

1 2

A. Turn off the power of the main unit

B. MFP PWB cover removal

C. Bar code Font ROM installation

D. MFP PWB cover installation

E. Turn on the power of the main unit

F. PCL expansion font list check

A. Check the packed items

A. Turn off the power of the main unit

B. MFP PWB cover removal

C. ROM replacement

D. MFP PWB cover installation

E. DSK firmware installation