Advertisement
Advertisement
Operating instructions vertical blinds & awnings markilux Vertical Blinds & Awnings
Overview
markilux 710 / 810 markilux 720 / 820
710 810
1
2
3
7
8
10
720 820
1
2
5
7
8 markilux 750 / 850
750 850
7
8
9
1
2
6
1 Cover cassette
2 Hand crank (for manual operation)
3 Tension rope
4 Guide track
5 Angled guide rail markilux 893
893
7
8
9
1
4
6 stainless steel guide rods
7 Cover
8 front profile
9 the fixture brackets
10 Fastening for tension ropes
GB
markilux
16.01.2019
7060346 TK + QS
markilux 730 / 830
730 830
1
2
5
6
7
8
9 markilux 740 / 840
740 840 1
2
4
5
7
8
9
1 Cover cassette
2 Hand crank (for manual operation)
3 Guide track
4 Angled guide rail
5 Cover
6 the fixture brackets
7 gas piston
8 Drop arm bracket
9 front profile
Attention: When retracting drop-arm awnings, there is danger of crushing between the drop arms and the guide rails.
It has to be ensured that there are no body parts in this range. It is important to observe in particular point 8 in the "Safety instructions" and point 12 of the chapter "Important notes".
Table of contents
markilux important notes markilux operating instructions
1. Reading the instructions
2. Awning with manual operation
2.1 Standard manual operation - outside operation
2.2 Awnings with interior operation (markilux 710 / 810, 720 / 820, 730 / 830, 740 / 840, 750 / 850)
2.3 Direction of rotation during retraction
3. Awning with motorised operation
4. Modification or retrofitting
5. Safety note
6. Awning with extendable standpipe (markilux 730 / 830)
8
8
7
8
Page
7
7
9
9
9 markilux.com
markilux important notes
Important information for the users of markilux awnings
1. Manufacturing number
Every markilux awning was produced individually according to your guidelines and has a fabrication number on it, through which this product becomes a unique product identifiable at any time.
2. Marking of important safety instructions
With this triangular warning, notes responding to dangers are marked which can result in bad injuries or even death.
Furthermore it marks important information on the function of the awning!
With this triangular warning, notes are marked which respond to dangers by electric shock resulting in bad injuries or even death.
3. Reading of "Important Instructions" and the "Operating Instructions"
The instructions handed by the authorized markilux specialist must be read before the first awning use. It is important to read all instructions for the safety of persons. All instructions are to be stored by the customer and have to be handed over to the new owner in case of an eventual transfer of the awning to Third Parties.
4. Proper use of an awning
0-14°
The awning is a sun protection construction.
Improper use may lead to significant hazards.
If the awning inclination is less than 25% =
14° measured at the horizontal or the awning is not extended entirely, then it must not be burdened by rainwater. There is a risk of the formation of water pockets in the awning cover and the awning may be damaged or fall.
Alterations like rebuilding or enlargements which are not intended by the manufacturer may only be carried out with the markilux manufacturers written approval. Additional awning burdens by means of object attachments or or rope wearing can result in damage or dropping of the awning and are therefore not allowed.
5. Wind resistance class
Wind resistance class
Wind speed V (km/h) maximum values
Wind speed V (m/s) maximum values
0
< 28
< 7.8
Wind resistance class 2 markilux folding-arm awnings, markilux 710/810, 720/820, 730/830, 740/840, 750/850, 893, 776/776 tracfix (depends on size), 876/876 tracfix (depends on size), 779/779 tracfix (depends on size), 879/879 tracfix (depends on size), 625 tracfix (depends on size), 8850
1
28
7.8
2
38
10.6
3
49
13.6
Wind resistance class 3 markilux 620 tracfix, 625 tracfix (depends on size),
776/776 tracfix (depends on size), 876/876 tracfix (depends on size),
779/779 tracfix (depends on size), 879/879 tracfix (depends on size),
770 tracfix, 870 tracfix, 8800/8800 tracfix, pergola, pergola compact, markant
The awning complies with the wind resistance category requirements named in the CE conformity mark (explanation see "handover declaration"). The CE conformity mark states an agreement to be proved according to the valid European guidelines requirements, the corresponding declarations can be requested via the authorized markilux service centre.
markilux markilux GmbH & Co. KG
Hansestrasse 53
D-48282 Emsdetten
DIN EN 13561
Awnings for exterior applications made in germany
markilux
6. Use in case of snow, ice, thunderstorm, storm and absence, also with automatic control
The awning must not be extended at snowfall or risk of frost. There is risk of the awning to be damaged or crash down. At approaching storm or bad weather fronts, severe gusts can occur suddenly to which even a control can not react immediately. An automatic control enhances the awning comfort, but does not excuse from the duty of care! During absence for longer periods, e.g. holidays or during the night, an automatic control system does not guarantee an enduringly faultless operation of your awning.
1.
2.
7. Leaves, snow and foreign bodies
Attention!
It is recommended to retract the awning before freezing wetness starts, at approaching storm respectively bad weather fronts or at absences. A possibly existing automatic function is to switch off!
Foliage and other foreign objects located on the awning cover, inside the awning box and in the guidance bars are to remove immediately. There is risk of the awning to be damaged or crash down. A build up of snow behind the awning can be avoided by installation of snow stoppers (snow collecting grid or the like) or regular removal of the accumulated snow.
8. Obstacles min. 50 cm
In the awning extension area, no obstacles may be located. There is danger for persons to be squashed in there. In order to avoid this, a safety distance of at least 50 cm has to be observed.
9. Motor in case of power cut
A motor-driven awning cannot be retracted without electricity. In very windy areas with frequent power cuts the use of an emergency power supply should be considered. Otherwise always retract the awning if the power is scheduled to be cut!
10. Uncontrolled operation during cleaning and maintenance jobs
Attention!
When working in operation radius (e.g. cleaning or service works), make sure the awning to be currentless (e.g. power switch off, remove plug coupling at drive cable, ...) There is risk of squeezing and falling down.
There is a risk of crushing body parts and falling. For works on manually operated units the crank should be removed and stored safely. If awnings are operated by various persons, a locking device switching of prime importance (controlled circuit breakers from outside) must be actuated, so that every awning retraction and extension is made impossible. Persons not familiar with proper awning use must not operate them.
markilux.com
11. Repair and spare parts
The awning is to check regularly for signs of wear or damage at covering, frame and its fixtures (with electric connection: also the power supply lines). The durability of the fixtures should be checked on an annual basis by means of a visual inspection or by an annual servicing of the marklilux specialist dealer. If damages occur, an authorized markilux specialist is to be entrusted with the adjustment.
Only spare parts released by the manufacturer may be used.
Attention! Risk of injury!
Please never try to repair disorders on your own! Awnings which need to be fixed must not be used.
Talk to your authorized markilux specialist about a preventive maintenance agreement!
12. Crushing and shearing zones
Attention! Depending on the type of awning there are crush and shear zones, e.g. between front profile and cassette and between moving parts. Items of clothing or limbs can be grabbed by the unit and pulled in. If the awning is installed at a height less than 2.5 metres above accessible traffic ways, then the awning may only be operated by a pushbutton switch which enables the moving parts to be viewed. Electric controls, radio-controlled motors with click in-switches are not permitted for such installations.
13. Metallic and pearl glimmer coatings of the awning frame
The look of plastic coatings of metal and plastic parts in metallic and/or pearl glimmer colour vary. These visual differences concern in particular the intensity and characteristic of the metallic effect, which may also lead to a change in the perception of the basic shade.
14. Disassembly and disposal
Attention: Risk of injury! When disassembling and disposing of the shading system, the parts under tension (e.g. folding-arms, counter tension systems or servo gear unit) have to be relaxed completely or secured beforehand. A markilux specialist should be commissioned for this!
15. Maintenance and care, characteristics cover and awning frame
Whether a cleansing is necessary or not depends strongly on environmental influences (traffic, air pollution, industrial gases etc.).
Depending on the degree of pollution, a regular cleansing is recommended.
Attention!
Always use an appropriate ascending aid and never rest again or attach to the awning!
15.1 Awning cover in wet condition
If possible, retract the awning when it is dry only! If the awning must be retracted wet, it has to be extended as soon as possible in order to dry. By the cover permanent weight, a deflection is possible which increases in wet condition. This occurrence does not influence the awning function and running qualities.
markilux.com
15.2 Cleaning the awning cover
The awning cover is equipped with special impregnation which reduces at every cleansing. For post-impregnation, commercial tent impregnation can be used. By re-impregnation, no new condition of the cover can be achieved yet.
Remove dust periodically with a soft brush in dry condition. Remove leaves, twigs and similar debris immediately. Remove small stains on the awning cover with commercial, preferably liquid mild detergent added to water (water temperature approx. 30°C, soap solution 5 %). Rinse thoroughly with water until all traces of the detergent have been removed.
15.3 Cleaning the awning frame
For cleansing of the awning frame, use commercial detergent for sensitive surfaces (pH-value between 5 and 8). Aggressive acids and scraping materials (like grinding fleece, emery, sand, pumice, etc.) are not allowed because they could alter the surface totally.
15.4 Characteristics resulting from the production and manufacture of awning fabrics
Awning covers are industrially manufactured textile products which serve both a functional and a decorative role. Although only first-class, quality controlled fabric is used in production, there are limits to the degree of perfection that can be achieved. Awning owners occasionally complain about certain imperfections in the fabric due to lack of knowledge. Defects actually to complain are only those which influence the cover life span. The following specified imperfections influence the awning cover durability and usage practicality in no way.
• Dogleg and wrinkle creases
At processing, like e.g. trimming, sewing and winding up of the cover onto the awning frame, dogleg traces can result which can not be avoided. Viewed against the light, the user of the awning has the impression that he sees dark stripes.
• Chalk and write effect
As with the previously mentioned processes, the cover may show a light change in colour
(pigment shifting) at folded spots caused by kinking the fibre.
• Winding folds / waviness
Winding folds/rippling: This occurs due to the permanent coiling and uncoiling of the cover on the roller. This effect can be explained by the fact, that the material is thicker close to the seams, coils more loosely between the seams of the cover. This effect can occur both directly next to the seam as well as also in the middle of web.
• Other irregularities
Irregularities caused by the production process which cannot be avoided, such as
• Knots, thread thickening and thinning, which can be seen in the cloth as points of light or as nubs
• Colour deviations in cloths produced in webs (e.g. in triangular shades)
• Individual thread breakages and expansions at the seams with resulting sagging
• Sagging of the cloth due to its own weight or after the formation of a "water sack".
can occur, and are unavoidable in production.
15.5 Flexing of the awning frame
The profile of the wider systems' awning frame can flex as well because of own weight. This occurrence does not influence the awning function and running qualities.
16. Tested awning cover
The certificate "STANDARD 100 by OEKO-TEX®" guarantees that no harmful dyes or chemicals were used in the making of markilux sunsilk snc and sunvas snc awning covers.
UPF = Ultraviolet Protection Factor
Fabrics made of sunsilk snc and sunvas snc achieve the highest possible solar protection factor for textiles (UPF 50+).
An awning fabrics with an ultraviolet protection factor of 50+ enables you to sit out safely in the sun fifty times longer than you would otherwise be able to do without suffering sunburn, if you were to rely solely on the protection provided by your skin. Max. duration of sunbathing under your awning = own protection time x 50
Test mark "Selfcleaning inspired by nature"
Awning fabrics made from sunvas snc and sunsilk snc offer a self-cleaning effect in rain (a minimum of 14° awning pitch is required to ensure water run-off).
17. Legal disclaimer
The graphics and text sections in these instructions have been created with care. No liability can be borne for any errors and their effects. We reserve the right to undertake technical modifications to the product and to these instructions! The instructions contain copyright-protected information. All rights reserved! The listed product or trade names are copyright trademarks.
markilux.com
Operation manual markilux Vertical Blinds & Awnings
1. Reading the instructions
Attention!
Read the operating instructions and all the documentation pertaining to the product (handover protocol), important guidelines, etc.) carefully and completely before using the product.
2. Awning with hand crank operation
2.1 Standard manual operation - outside operation
1. Engage the hook of the crank rod in the transmission eyelet.
Turn the crank rod until the driving pin engages in the bayonet closure.
2. Hold the crank rod with one hand on the upper and one hand on the lower turning handle. During the operating procedure, pull the crank slightly towards the operator.
3. If the transmission eyelet is on the right side (as illustrated):
• Extension of the awning cover: Counterclockwise rotating of the crank.
• Retracting the awning cover: turn the crank clockwise.
• If the transmission eyelet is at the left side, the directions of rotation are precisely the opposite.
4. After retraction and extension respectively, remove the hand crank from the gear by slightly pushing it upwards and turning it and keep in a safe place.
5. If the crank rod is to be left in the transmission eyelet, it must be secured against uncontrolled movements (e.g. during wind)!
Tip: If the extended fabric is not under tension, because the fabric had been unwound too far, push the awning inwards until the fabric tension is reached again.
markilux.com
7
2.2 Awnings with interior operation
(markilux 710 / 810, 720 / 820, 730 / 830, 740 / 840, 750 / 850)
90°
90°
1
2
3
1. Remove the crank rod from its magnetic holder (1) and turn the lower crank sections (3) at the joints in such a way that they form a 90° angle to each other.
2. Operation is carried out in accordance with points 2.-3. of chapter 2.1 "Standard manual operation - outside operation".
3. After retraction and extension respectively, straighten the joints of the crank rod in such a way that the rotary handles are arranged concentrically to each other. Afterwards always secure the crank rod against uncontrolled movements in the magnetic holder.
1 Magnetic holder
2 Crank rod
3 Turning handle
2.3 Direction of rotation during retraction
Attention: Awnings with winding handle have a transmission end stop to limit the extension travel. It prevents incorrect coiling of the cover onto the roller. The transmission end stop must never be approached with force. Shortly before reaching the end position in the extending direction, the crank operation should be slowed in a controlled manner in order to avoid a forced overtravel of the transmission brake.
If the transmission end stop is defective, a coiling of the cover from below onto the roller during retracting can lead to damage to the awning cover and the awning frame.
3. Awning with motor drive
With markilux hand-held remote control (optional):
DOWN button
STOP button
Down button
Channel selection button markilux
PROG button
(on the reverse of the handset)
Extend the awning by pressing the push-button switch for extension/retraction. With radio-controlled operation, your markilux specialist must exactly explain the functions on the radio remote control to you, since, depending on the equipment, he can set these for you individually.
Here observe the separate operating instructions of the motor and, if available, the controller manufacturer.
The final stop for awning extension/retraction is limited. The end stop for the extension direction will be set by your specialist dealer.
Tipp: If the awning does not extend in a uniform manner, retract it and extend it again. If this problem arises again, fully retract the awning and inform your markilux specialist dealer.
8 markilux.com
Protection against overheating:
Multiple extension and retraction of the awning in rapid succession results in an automatic motor switch-off to preserve it from overheating. After cooling down the motor switches itself on again in operating readiness.
STOP
4. Conversion or retrofitting
The following modifications can be carried out retrospectively on your awning by your markilux specialist.
• Replacement of the awning fabric
• Installation of a motor
• Retrofitting an automatic control system. In principle a motor drive must be available. Ask your specialist retailer about sun and wind sensors, remote control etc.
5. Safety note
Attention - risk of injury!
The folding arms of the markilux 730 / 830, 740 / 840 and 745 /845 generate very high compressive stress on the front profile and the fabric of the awning. This compressive stress is generated by tension springs, which are located within the folding arms.
Because of the accident prevention regulations, these gas pistons must not be dismantled, opened (e.g. by drilling), forcibly damaged or heated over 80°C. The gas pistons contain oil and must be disposed of only through the raw materials trading sector or a hazardous waste collection site.
In case installation works to your awning are necessary, these have to be carried out only by a markilux expert!
6. Awning with extendable standpipes (markilux 730 / 830)
3
4
5
1
2
6
Attention: From time to time kindly check the stability of your 730 / 830, if it is mounted at extendable standpipes. If required, the thread has to be adjusted with the
SW threaded screw at the foot plate.
1 Vertical column
2 arm fixture
3 star knob
4 Stopper
5 Hexagonal screw SW 19
6 base plate markilux.com
9
Advertisement
