START HERE
1 of 4
QUICK START GUIDE
1 Carefully unpack box.
2 Unlock and open front panel of unit for access to internal components.
r
IMPORTANT!
We recommend mounting Ascent X1 on a standard gooseneck pedestal.
If using alternate mounting, the optional
Ascent 10' Cable Extension ( p/n 16-X-EXT ) must be purchased. Follow the instructions included with the extension before moving on.
Failure to do so may result in no signal!
Continued on next page...
What’s what?
All the important components labeled for you.
Copyright © Security Brands, Inc.
Terminal block
For wiring to gate operator or door operner
Camera kit mounting location
Camera kit sold separately.
Unit shown with front panel fully open.
Internal wiring not shown for clarity.
Antenna cable
Reset button and terminals for performing hard reset
Speaker connector
Speaker can be disconnected temporarily if unit is intermittently beeping. This is usually due to a SIM card that is not yet activated.
SIM card
If you have your own SIM card, see page 4 and follow the instructions entitled
Installing Custom SIM Card .
r
IMPORTANT!
Ascent X1 WILL NOT WORK until the activation process has been completed!
Follow the Activation Guide or call
Summit Control at (844) 259-8265 to activate your unit.
WARNING!
AUTOMATIC GATES CAN CAUSE
SERIOUS INJURY OR DEATH!
ALWAYS CHECK that the GATE PATH IS
CLEAR BEFORE OPERATING !
Reversing or other safety devices should
ALWAYS BE USED !
QSG-16X1-EN Rev. D (12/2015)
3
Connect wires
Feed wires through back of unit and connect as shown.
QUICK START GUIDE
Supplied 12-VAC
Transformer
OR
Third-Party 12–24-V AC/DC
Power Source
+ –
Gate Operator / Door Opener
POWER
12–24 VAC/VDC
2 of 4
STOP!
Before proceeding, double check that wiring is correct and unit has power!
For additional wiring options, see page 3 .
Copyright © Security Brands, Inc.
Relay B can be wired to asecond device in the same manner.
STATUS POWER
12–24 VAC/VDC
RELAY A RELAY B EVENT
Ascent X1 Terminal Block
4 Close and lock front panel.
5 Make sure gate path is clear, then key in temporary code
2012
on keypad and con fi rm gate opens.
CAUTION!
If you will not be using the supplied 12-VAC transformer, please go to page 4 and follow the procedure, Using a Third-Party Power Source .
Do not exceed 24 VAC/VDC! Failure to choose a compatible power source can damage unit!
N
INSTALLATION COMPLETE!
Now follow the Activation Guide to create an account and begin using Ascent.
QSG-16X1-EN Rev. D (12/2015)
QUICK START GUIDE
A
Status Check
Wiring to enable device status check
Gate Operator
(If equipped with limit switches)
B
Open/Close Mode
Wiring when not using gate operator’s “timer-to-close” function.
Gate Operator / Door Opener
POWER
12–24 V AC/DC
N/C
N/O
COM
Close Limit Switch
3 of 4
Optional wire splices
N/C
N/O
COM
Open Limit Switch
Connected as shown in Step 3
Connected as shown in Step 3
Copyright © Security Brands, Inc.
STATUS POWER
12–24 V AC/DC
RELAY A RELAY B EVENT
Ascent X1 Terminal Block
STATUS POWER
12–24 V AC/DC
RELAY A RELAY B EVENT
Ascent X1 Terminal Block r
IMPORTANT!
Open/Close Mode will only work if the device is set to that mode from the Device Settings page in the Admin Area !
You CANNOT log in until account activation has been completed!
QSG-16X1-EN Rev. D (12/2015)
Using a
Third-Party
Power Source
(Optional)
QUICK START GUIDE r
IMPORTANT!
If you would like to use a third-party power source, such as solar, verify that it conforms to the following specs:
Input
Current Draw
12–24 VAC / VDC must be within ±10% less than 100 mA @ 12 VDC less than 75 mA @ 24 VDC
4 of 4
3a Connect wires to unit as shown in
Step 3.
3b Connect wires to your power source, making sure you connect positive to positive and negative to negative.
CAUTION!
Double check that you’ve wired from positive on Ascent X1 to positive on your power source and negative on Ascent X1 to negative on your power source.
Reverse polarity can damage Ascent!
1 Slide SIM card holder in OPEN direction and lift to swing open.
2 Remove existing SIM card and install new SIM card.
3 Swing cover back down completely and slide in CLOSE direction to lock.
Installing
Custom
SIM Card
(Optional)
?
NEED HELP?
Contact us at (844) 259-8265 or visit summitcontrol.com/contact
Copyright © Security Brands, Inc.
QSG-16X1-EN Rev. D (12/2015)
