DIGITAL CALIPER INSTRUCTIONS
IP67 Digital Caliper with Absolute Encoding System
110-DCP Series
Fig 1
Features
• Absolute Measuring System
• Waterproof, oilproof, anti-electromagnetic interference, protection rating IP67 (IEC 60529)
• LCD Display
• Low-voltage alarm and calculation error alarm
• Infinite setting speed, no speed error
• Sleep mode after 5 minutes of no use
• Functions: mm/inch | Absolute/Incremental measurement
Technical Specification
• Measuring range: 0 -150mm | 0 - 200mm | 0 - 300mm
• Resolution: 0.01mm/0.0005in
• Repeatability: 0.01mm/0.0005in
• Operating temperature: 0°C - 40°C
• Storage temperature: -10°C - 60°C
• Relative humidity: 100%
• Protective level: IP67 (IEC 60529)
• Battery type: 3V lithium battery (CR2032)
Operation
• ABS/INC Conversion: In the "ABS" mode, when the lower jaws is closed, “0.00” is displayed, the absolute origin
position of the digital caliper, and "ABS" is displayed on LCD screen. For relative measurements at any
position, press the button “0/ON” and "INC" is displayed on the LCD screen and “0.00” is displayed at current
position (relative measurement mode). To convert to "ABS" mode, press the button“0/ON” until "ABS" is
displayed on the LCD screen and then release the button. The absolute position value is displayed.
• mm/in conversion: Press the button “mm/in” to switch to mm or inch mode.
• Manual switch off: Press the button “0/ON”until OFF is displayed and then release the button.
(Note: Keep pressing the button, sequence of “0/ON”, “INC” “ABS” “OFF” “INC” will be displayed,
when the needed function appears, release the button)
For more information visit www.moore-and-wright.com Partners in Precision
I
P67 DIGITAL CALIPER WITH ABSOLUTE ENCODING SYSTEM 110-DCP SERIES
• To calibrate the absolute origin position: When the external measuring faces are closed and “0.00” is not
displayed due to worn measuring faces, etc, this shows the absolute origin position has changed. Now it’s
necessary to calibrate the absolute origin. 1 Switch on the power and make the external measuring faces
touch. 2 Press button “mm/in” until “0.00” is displayed then release the button. 3 Move the slider back
and forth several times. Make the external measuring faces touch every time and check if “0.00” is displayed.
If “0.00” is not displayed, repeat the operation until “0.00”is displayed.
• Workpiece measurement methods: This digital caliper measures internal dimensions (such as slots, holes, etc.), external dimensions (such as cylindrical, linear outer dimensions, etc.) depth dimensions (such as groove depth, step height, etc.), etc. Its measurement methods and value reading are the same as ordinary digital calipers. (See Fig 3 )
Internal Measurement Depth Measurement
Fig 2 Fig 3
Step Measurement External Measurement Fig 3
Note: Version with thumb roll on request
Notes
• Do not charge or burn the battery. If the battery is swallowed, see a doctor immediately.
• The jaws of this caliper have a sharp edge. Handle it with great care to avoid injury.
• Avoid colliding and dropping which may cause deformation and reading errors.
• Keep all the measuring faces and guiding faces clean.
• If it’s not used for a long time, remove the battery and store it in the packing box.
• The electronic components must not be exposed to chemical solvents.
• When replacing the battery, refit the sealing O-ring in case it’s deformed or damaged.
• The digital caliper adopts absolute encoding measuring system, the clearance and position between the reading head and the steel scale are strict and precise. Do not dismantle any part of it in order to avoid the reading head’s failure of reading the scale.
TROUBLESHOOTING
Serial No.
Malfunction
1
Cause
Water enters the electronic
1.Battery cover hasn’t been tightened
2.The sealing O-ring is deformed components due to
3.The sealing O-ring is damaged poor gas tightness
4.Other causes
2
3
Incomplete or missing LCD display
No LCD display
1.Water enters the electronic components
2. Other causes
1.Flat battery
2.Poor contact
Solution
Tighten the screws in the battery cover
Adjust the O-ring’s shape
Replace the sealing O-ring
Send back for repair
Dry it.. Avoid water entering (see no.1)
Send back for repair
Replace the battery
Improve the battery seat
4 LCD displays
2.Other causes
1.Low power
Send back for repair
Replace the battery
1.The temperature is lower than 0ºC or higher than 40ºC Adjust the ambient temperature between 0°C~40°C
2. Electronic components are damaged Send back for repair 5 LCD displays “Err-3”
3.Low power / poor contact Replace battery / improve the battery seat
Because of the products’ continuous upgrading, the instructions may be slightly different from the actual product, the actual product shall prevail.
For more information visit www.moore-and-wright.com Partners in Precision
