NewAge Products 85827 142.25-in W x 84-in H x 25.5-in D Gray Painted Door and Drawer Wall Fully Assembled Stock Prefabricated Cabinet Installation Manual

Document

Home Cabinets

INSTALLATION GUIDE

Warning: Excessive weight hazard!

Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.

STOP

ATTENTION

Is your Home Cabinet damaged?

Need help or spare parts? For fastest service, contact NewAge Products at 1-877-306-8930; or [email protected].

Do not return to the retailer.

IM-HKC.01A-01

Index

Unpacking

Product Inspection

Home Cabinets and Accessories

Tools Needed

Optional Tools

Hardware

Cabinets purchased with Doors and Drawer front panels

Cabinet frames

Kitchen Island

Accessories

Room Preparation

Before you begin

Measuring and Marking your Space

Preparing your Room

Installation Layout Options

Corner Layout

U - Shaped Layout

Linear Layout

Island Layout

Installation Overview

Removal and Installation of Doors

Installing the Door Hinges

Blind Corner Cabinet

Index

Base and Wall Cabinets

Pantry cabinet

Adjusting the Door Hinges

Removal and Installation of Drawers

Installation of Drawer Front Panels

Top Drawer

Middle and Bottom Drawers

Installation of Drawer Front Panels

Adjusting the Drawer front panel

Adjusting the Wood Shelves

Installation of Glass Shelves on Wall Cabinets with Glass Doors

Installation of Feet for Base Cabinets

Corner Layout Installation

Blind Corner Cabinet - Filler Panel Installation

Installation of Blind Corner Cabinet

Installation of Base Cabinets

Wall Rail Installation for Wall Cabinets

Wall Cabinets Installation

Installing the Above Fridge Cabinet

Installing the Wall Cabinet Side Panels

Installing the Crown Moldings

Installing the Wall cabinet Skirting

Installing the Base Cabinet Side Panels

Index

Installing the Toe kicks

Installing the Filler piece

Installing the Linear layout

Installing the Island layout

Creating a 26” Deep Island

Creating a 40” Deep Island

Installing the U shaped layout

Additional Accessories offered by NewAge

SPARE PARTS - BASE CABINET with DOORS

SPARE PARTS - BLIND CORNER

SPARE PARTS - 3 DRAWER

SPARE PARTS - SPLIT DRAWER and DOORS

SPARE PARTS - PANTRY

SPARE PARTS - SINK CABINET

SPARE PARTS - STANDARD WALL CABINETS

SPARE PARTS - CORNER WALL CABINET

SPARE PARTS - GLASS DOOR WALL CABINETS

DOOR AND DRAWER REFERENCE TABLE

Manufacturer One Year Limited Warranty

ATTENTION :

Installing a kitchen is considered a major project, and many different skills are needed to be able complete the project correctly. There are many tools needed to make the process smoother, and NewAge recommends using a professional kitchen installer for the best overall installation experience.

It is recommended to book your installer to begin work one week after receiving the products to avoid any delay in installation, due to missing/damage products during the transit.

101

103

105

106

Unpacking

• Begin by placing the package on a covered flat surface.

• Remove all cardboard, foam packaging material and clear plastic bags.

• Dispose / recycle all packaging materials.

• Verify all the contents in the box and gather the required tools. See “Tools Needed” in the page 7 .

Product Inspection

• Check to see all parts are received as per the order placed.

• Contact NewAge Products at 1-877-306-8930; for any missing parts.

• Inspect the products for any damages before starting the installation.

• Go through the installation instructions carefully before starting the installation.

Home Cabinets and Accessories

Base Cabinets Wall Cabinets Side Panels Crown Molding

Toe Kick Skirting Led Lights Shelves

Doors

Handles Sink Granite Countertop

Tools Needed

Hammer Pry Bar Straight Edge Phillips Bit Level

Tape Measure Pencil Miter Box Drill 5/32” Drill Bit

Saw C - Clamps Wood Shims Stud Finder Safety Glasses

Hacksaw

Optional Tools

Tin Snips Extended Philips Driver #2

Compound Mitre Saw Circular Saw Vacuum Cleaner

Hardware

Hardware required for each cabinet comes in a separate hardware box attached inside the respective cabinets.

If you purchase your cabinets without doors or drawers, additional hardware required for installing the doors/drawers are also included in the hardware box.

Adjustable leg

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm

Chip board screw for

Cabinets

Ø4mm X 30mm

Lag Screw

Ø6mm X 70mm

Molly Bolts

HM 6x37 S

Door Hinge 155° Door Hinge 110° Door Hinge 95°

Drawer support bars

(only for middle and bottom drawers)

Support bar locks

Drawer Stabilizer

(Only for 36”

Cabinet drawers)

Drawer Front

Connector

Glass Shelf Clips Toe kick clips

Hardware for:

Cabinets purchased with Doors and Drawer front panels

Base Cabinet with Doors / Drawers

Hardware

Adjustable legs

Flat head chipboard screws

Lag screws

Toekick Clips

Chipboard screws for

Toekick clips

Specifications Quantity

Ø4mm X 30mm

Ø6mm X 70mm

Ø3.5mm X

16mm

Wall Cabinet with Wooden Doors

Hardware

Mounting Bracket and Covers

Flat head chipboard screws

Molly Bolts

Lag screws

Specifications Quantity

Ø4mm X 30mm

HM 6x37 S

Ø6mm X 70mm

Wall Cabinet with Glass Doors

Hardware

Mounting Bracket and Covers

Flat head chipboard screws

Molly Bolts

Lag screws

Shelf Pin

Glass Shelf Clip

Specifications Quantity

Ø4mm X 30mm

HM 6x37 S

Ø6mm X 70mm

Corner Wall Cabinet

Hardware

Mounting Bracket and Covers

Flat head chipboard screws

Molly Bolts for dry wall

Lag screws

Cover for Mini Fix

Specifications Quantity

Ø4mm X 30mm

HM 6x37 S

Ø6mm X 70mm

Above Fridge Cabinet

Hardware

Flat head chipboard screws

Molly Bolts for dry wall

Lag screws

Specifications Quantity

Ø4mm X 30mm 8

HM 6x37 S

Ø6mm X 70mm

Hardware for:

Cabinet frames

Base Cabinet for Doors

Hardware Specifications Quantity

Purchased with Doors

Adjustable legs 4

Ø4mm X 30mm

Flat head chipboard screws

Lag screws

Toekick Clips

Chipboard screws for

Toekick clips

Ø6mm X 70mm

Ø3.5mm X

16mm

Door Hinges 2 (Single door) or

4 (Double door)

Base Cabinet for Drawers

Hardware Specifications Quantity

Purchased with Drawer Fronts

Adjustable legs 4

Flat head chipboard screws

Lag screws

Toekick Clips

Chipboard screws for

Toekick clips

Ø4mm X 30mm

Ø6mm X 70mm

Ø3.5mm X

16mm

Drawer Front

Connectors

Drawer Stabilizer

(only for 36” Cabinet)

Drawer support bars

Drawer support bars locks

Chipboard screws for

Drawer Stabilizer

Ø4X15.5L

Blind Corner Cabinet

Hardware Specifications Quantity

Purchased with Doors

Adjustable legs 4

Flat head chipboard screws

Lag screws

Toekick Clips

Chipboard screws for

Toekick clips

Ø4mm X 30mm

Ø6mm X 70mm

Ø3.5mm X

16mm

Door Hinges 2

Wall Cabinet

Hardware Specifications Quantity

Purchased with Doors

Mounting Bracket and Covers

Ø4mm X 30mm

8 Flat head chipboard screws

Molly Bolts for dry wall

Lag screws

Door Hinges

Shelf Pin (only for glass door cabinet)

HM 6x37 S

Ø6mm X 70mm

2 (Single door) or

4 (Double door)

8 Glass Shelf Clip

(only for glass door cabinet)

Base Cabinet for Drawers and Doors

Hardware Specifications Quantity

Purchased with doors

Adjustable legs 4

Flat head chipboard screws

Ø4mm X 30mm

Lag screws

Toekick Clips

Chipboard screws for

Toekick clips

Ø6mm X 70mm

Ø3.5mm X

16mm

Door Hinges 2 (Single door) or

4 (Double door)

Drawer Front

Connectors

Drawer Stabilizer

(only for 36” Cabinet)

Chipboard screws for

Drawer Stabilizer

Ø4X15.5L

Corner Wall Cabinet

Hardware Specifications Quantity

Purchased with doors

Mounting Bracket and Covers

Ø4mm X 30mm

8 Flat head chipboard screws

Molly Bolts for dry wall

Lag screws

Door Hinges

HM 6x37 S

Ø6mm X 70mm

Hardware for:

Cabinets Frames

Above Fridge Cabinet

Hardware Specifications Quantity

Purchased with Doors

Ø4mm X 30mm 8 Flat head chipboard screws

Molly Bolts for dry wall

Lag screws

Door Hinges

HM 6x37 S

Ø6mm X 70mm

Pantry Cabinet

Hardware Specifications Quantity

Purchased with Doors

Adjustable legs 4

Flat head chipboard screws

Lag screws

Toekick Clips

Chipboard screws for

Toekick clips

Ø4mm X 30mm

Ø6mm X 70mm

Ø3.5mm X

16mm

Door Hinges 2

Kitchen Island

Hardware

Adjustable leg base

Adjustable leg

Chipboard screws

Specifications Quantity

Φ3.5Χ 16 16

Hardware

Accessories

Crown Molding

Hardware

Chipboard screws

Specs

Ø3.5mm X

35mm

Quantity

Skirts

Hardware

Chipboard screws

Specs

Ø3.5mm X

35mm

Quantity

Room Preparation

ATTENTION

NewAge recommends using a professional kitchen installer to prepare and install kitchen cabinets.

NOTE

If you are unfamiliar or unsure of how to handle utility connections, have a qualified professional perform these duties.

Before you begin

• Shut off all existing water, power and utility lines.

• Remove existing appliances (stove, oven, refrigeration, sink, and dishwasher). It is best to move these out of the room for easier access to the work area while the remodeling is being done.

• Remove old cabinets and countertops.

• Remove any moldings from the walls where cabinets are to be installed.

Measuring and Marking your Space

It is very important to measure and understand your room space for planning your installation.

Use a tape measure and a pencil to measure and identify the following:

A. Height of the room from the floor to the ceiling.

B. Width of the room wall to wall / wall to door.

C. Height from the floor / Ceiling to any windows to ensure the cabinets fit.

D. Location of any service points for plumbing,electrical and any other use.

E. Any other permanent fixtures like pillars.

Room Preparation

Preparing your Room

• Locate the uneven areas to adjust the cabinets in order to make the installation plumb, true and square.

Plumb Line

Corner is out of plumb

2 3/8”

30” or 36”

Mark top line for wall cabinets

Refernce line for wall rails

Mark bottom line for wall cabinets

54”

1.25” for Granitetop

Base level line

Mark first line at

34.75 inches for cabinets.

36”

1.25”

Plumb Line

High points on floor.

• Using a carpenter’s level, find the high point of the floor.

• Check all around the room within 24” of the wall where base cabinets will be attached.

• From the high point, mark a level horizontal line using a straight edge, on the walls where the cabinets will be attached. This will be called the base level line.

• From the base level line, measure up 34 3/4” and mark another level horizontal line for the base cabinets.

• Add 1-1/4” for a standard NewAge countertops (if you are using a custom countertop, measure the thickness accordingly) and 18 inches for a standard backsplash. Mark the bottom line for wall cabinets at this 54-inches from the base line which will serve as a guide for hanging the cabinets.

• Mark the top line for wall cabinets at 30” or 36” (according to the height of wall cabinets selected) from the bottom line for wall cabinets.

• Mark a reference line 2 3/8” below the measured top line of the wall cabinet. This Line acts as a reference to install suspension rails on the wall.

Room Preparation

• Use a stud finder to locate the wall studs. The wall studs are crucial to properly support the weight of the cabinets.

Locate Wall Studs

• Using a carpenter’s level, check the walls for uneven spots. Wall unevenness can cause cabinets to be misaligned resulting in racking or misalignment of the doors and drawer fronts. At the point where these uneven spots interfere, high spots should be removed by scraping and sanding off excess plaster or sheet rock. Low spots should be shimmed with pieces of wood shims.

• Mark the outlines of all the cabinets on the wall to check actual cabinet dimensions against your layout to confirm that the room design used will work.

• Mark down all plumbing and other utilities. Check that everything fits with the measurements from your plan and your electricity, water, gas and ventilation connections are where you want them to be.

36” Wall Cabinet

24”

Glass Door

Wall Cabinet

Corner

Wall

Cabinet

Above

Microwave

Cabinet

24”

Wall Cabinet

Above

Fridge Cabinet

36” Sink Cabinet

24” Cabinet

18”

Base

Cabinet

Blind

Corner

Cabinet

Stove

24”

3- Drawer

Cabinet

Fridge

Pantry Cabinet

Example of cabinets outlined on wall

Installation Layout Options

Corner Layout Linear Layout

U - Shaped Layout

Island Layout

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

Installation Overview

The section gives you an overview of cabinets installation process. Refer to the corresponding sections in this install guide for step by step process.

Remove doors and drawers of all the cabinets and store in a safe area where they cannot get damaged during installation

Install leveling legs to all the base cabinets. Make sure to install on the correct side for single door cabinets.

Note

It is recommended to install all base cabinets first. If you are installating a corner layout start with the Blind Corner Cabinet.

Install the blindcorner cabinet, 9” offset from the wall.

Install base cabinets according to the planned layout.

Install all wall cabinets according to the planned layout.

60mm (2.36”)

Installation Overview

Install Side panels.

Install Skirting and Crown moldings.

Install Toekicks to all base cabinets.

Install doors and drawers of all the cabinets.

Install Handles for all the cabinets.

Install all other accessories purchased with the cabinets.

Removal and Installation of Doors

Installing the Door Hinges

If you’ve purchased custom color or Espresso doors your cabinet will arrive without the doors attached. You will be required to first, pre-install the hinges onto the doors, then attach the doors after installing all cabinets according to the planned layout.

Remove the protective film on the doors and drawer fronts before the installation.

1 Locate the pre-drilled holes on the back edge of the doors.

Fix the Hinges in position aligning with the holes. Tighten the pre-installed screws on the hinges.

Removal and Installation of Doors

Blind Corner Cabinet

If you purchase your cabinets with doors, remove doors of all the cabinets before installation. Install doors after installing all cabinets according to the planned layout.

1 Open the cabinet door and identify the door hinges.

Press the release clip on the front and pull the hinge clips outwards to release the door from cabinet.

Remove the door.

4 Install the door and press the hinge onto the hinge plate.

Removal and Installation of Doors

Base and Wall Cabinets

If you purchase your cabinets with doors, remove doors of all the cabinets before installation. Install doors after installing all cabinets according to planned layout.

1 Open the cabinet doors and identify the door hinges for each door.

Press the release clip on the front and pull the hinge clips outwards to release the door from cabinet.

Remove the door.

4 Install the door and press the hinge onto the hinge plate.

Removal and Installation of Doors

Pantry cabinet

If you purchase your cabinets with doors, remove doors of all the cabinets before installation. Install doors after installing all cabinets according to planned layout.

1 Open the cabinet doors and identify the door hinges for each door.

Press the release clip on the front and pull the hinge clips outwards to release the door from cabinet.

Remove the door.

4 Install the door and press the hinge onto the hinge plate.

Removal and Installation of Doors

Adjusting the Door Hinges

Note:

After the cabinets & doors have been installed it is up to the customers to make the adjustments to the hinges to ensure that the doors and drawers are all leveled.

Rotate the screws on the hinges using a screwdriver to adjust the position of the doors after installation.

Wall and Base cabinets

Blind corner cabinet

Pantry cabinet

Soft Close

Spring Tension

Removal and Installation of Drawers

It is recommended to remove all cabinet drawers before installation.

Slide out the drawer.

2 Remove cover on the both side of the drawer.

3 Pull the clips up from both sides of the drawer and slide the drawer off the slides.

4 Place the drawer in position over the rails and push it in to install.

Removal and Installation of Drawers

Place the drawer in position over the rails and push it in to install. Re-install cover plate on both sides of drawer.

Installation of Drawer Front Panels

Top Drawer

If you’ve purchased cabinets with doors/drawer front separately, you will be required to install the drawer front connector onto the drawers.

Take the Top drawer front panel and fix the drawer stabilizer(36” Drawer only) into two holes at the centre on back of the panel.Tighten the screws using a philips screwdriver.

Fix the dawer front connectors into the holes at both ends of the panel. Tighten the screws using a philips screwdriver.

Only for 36” Drawer

Push the top drawer front panel into the top drawer and make sure the drawer front connectors are locked into the drawer properly.

Open the drawer and drill in two Ø4mm

X15mm screws through the holes on the drawer stabilizer from the bottom.

Installation of Drawer Front Panels

Middle and Bottom Drawers

Take the Middle drawer front panel and fix the drawer stabilizer(36in Drawer only) into the two holes at the centre on back of the panel.Tighten the screws using a philips screwdriver.

Fix the dawer front connectors into the bottom two holes at both ends of the panel. Tighten the screws using a philips screwdriver.

Fix four support bar locks into the top four holes at both corners of the panel. Tighten the screws on the locks using a philips screwdriver.

Push the middle drawer front panel into the middle drawer and make sure the drawer front connectors are locked into the drawer properly.

Installation of Drawer Front Panels

Middle and Bottom Drawers

Open the drawer and drill in two Ø4mm

X15.5L screws through the holes on the drawer stabilizer from the bottom.

Take a drawer support bar and slide the cover inwards.

Fix the support bar to the drawer by pusing it into the slots on the back of the drawer and sliding the support pin on the front into the support bar locks.

Installation of Drawer Front Panels

Middle and Bottom Drawers

Slide the cover on the support bar outwards.

Install all four darwer support bars similarly.

Similarly install all support bars for the bottom drawer. Follow steps 1 to 9.

Installation of Drawer Front Panels

Adjusting the Drawer front panel

Note: Adjust the drawers prior to using the kitchen.

Adjust the drawer front panel downwards by rotating the screw (A) counter clockwise on both sides of the drawer.

A

Adjust the drawer front panel upwards by rotating the screw (A) clockwise on both sides of the drawer.

A

Adjust the drawer front panel to the right by rotating the screw (B) counter clockwise.

B

Adjust the drawer front panel to the left by rotating the screw (B) clockwise.

B

Remove the drawer front panel by rotating the screw(C) counter clockwise.

C

Adjusting the Wood Shelves

All Wooden shelves are delivered pre-installed with the cabinets. You can adjust the shelves at different heights.

Each shelf is supported by four support dowel pins which goes under the support housing. Support housing can be locked to fix the position of shelves.

Slide the shelf lock outwards at all corners on the bottom of the shelf.

Cabinet wall

Shelf

Cabinet wall

Shelf

Lift the shelf upwards from the support dowel pins and remove the shelf out from the cabinet.

Support dowel pins can be removed and installed at different holes on the carcass to install shelves at different heights.

5 Install shelf by placing the shelf resting on the support dowel pins.

6 Slide the shelf lock inwards at all corners on the bottom to lock the shelf.

Installation of Glass Shelves on Wall Cabinets with Glass Doors

All Glass shelves for the Glass door cabinets are delivered uninstalled with the cabinets. Install

Glass shelves after installation of the cabinets.

Four shelf support brackets for each shelf is needed for the support. Pull the lock downwards and move the top portion of the support bracket.

2 Install support brackets into the holes on the cabinet carcass.

Locked Unlocked

3 Slide in the glass shelf through the support brackets.

Press the top portion the support bracket downwards and push the lock upwards for locking the shelf in position.

Push to lock

5 Follow steps 1 to 4 for installing the other glass shelf.

Installation of Feet for Base Cabinets

ATTENTION: Once feet are intalled removing them will cause damage to the cabinets.

Install adjustable feet for all base cabinets before beginning the installation process. The adjustable legs are packaged in a hardware box inside the cabinet

1 Remove the doors of all cabinets. Refer to page 19 - 21 for removal of doors.

Flip the cabinets upside down on a protective soft surface and locate the holes at each corner of the cabinet.

Ensure to fix legs on the correct side based on door opening.

Two or more people are required to lift/move cabinets into place.

Four adjustable legs for each cabinets are provided in the hardware box. Remove leveling leg base from the legs before installation. The leveling legs have a 3/4” height adjustability.

Leg base

Leg post

Installation of Feet for Base Cabinets

Push and fit the leveling leg base into one of the holes and making sure that the tab is overlapping the side panel of frame.

Insert the leg post into the leg base and psuh it in to lock the entire leg assembly into place. Removing leg post after locking will damage cabinet.

6 Repeat the step 2 to 4 to install all the leveling legs. Ensure all legs are in the lowest position.

Carefully lift up and flip the cabinet.

Installation of Feet for Base Cabinets

7 Adjust the legs to level the cabinet.

Max. 3/4” adjustable

Corner Layout Installation

Blind Corner Cabinet - Filler Panel Installation

Note: When installing a corner layout, it is recommended to start the cabinets installation with blind corner cabinet. Install the L - filler panel provided inside the blind corner cabinet before installing it to the wall.

Parts required

Take the L-shaped filler piece which comes with the blind corner cabinet and identify two pilot holes provided on the cabinet.

Ø4 mm X 30 mm

Chipboard Screws

L-Shaped

Filler Piece Drill

C-clamp the L - filler piece into position ensuring the top and bottom are flush with the cabinet.

Take two Ø4mm X30mm chip board screws from the hardware box and screw the L-fillet piece to the cabinet from the inside using the pilot holes. Ensure not to over screw.

Do not screw-in L-Panel from the outside.

Corner Layout Installation

Installation of Blind Corner Cabinet

Note: It is recommended to start installing the corner base cabinet first and install other wall cabinets on the both sides.

Install the blindcorner cabinet, 9” offset from the wall.

Placing a level on the cabinet front to back, level the cabinet by rotating the feet. Repeat this step with the level left to right. The cabinet should be level along all edges.

9”

Align the adjacent cabinet (with doors/ drawers installed) next to blind corner cabinet.

Align the cabinets, such that the filler piece on the blind corner cabinet is flush with the doors of the adjacent cabinet.

Corner Layout Installation

Installation of Base Cabinets

Once the adjacent cabinet has been aligned with the corner cabinet, level this cabinet front to back and left to right by adjusting the leveling legs.

Mark a position for pilot hole at the vertical center of back panel, aligned with the wall studs.

Referencing the pre marked location, drill pilot hole using a 5/32” in drill bit. Screw in the Corner and Adjacent Cabinets into the wall studs using the Ø6mm x70mm Lag screws provided.

Corner Layout Installation

Installation of Base Cabinets

8 Referencing your design layout, align the next cabinet to be installed accordingly.

Placing a level on the cabinet front to back, level the cabinet by rotating the feet. Repeat this step with the level left to right. The cabinet should be level along all edges and aligned with the adjacent cabinet.

2”

Fix both cabinets together to prevent movement using a c-clamp. Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach cabinets together.

2”

Mark a position for pilot hole at the vertical center of the back panel, aligned with the wall stud.

Referencing the pre marked locations, drill pilot holes into each wall stud using a

5/32” drill bit. Screw in the cabinet to the wall stud using the Ø6x70mm Lag screws provided.

2”

Corner Layout Installation

Installation of Base Cabinets

Similarly install other cabinets according to the layout, secure cabinets each other and secure them to the wall.

2”

Two or more people are required to lift/move cabinets into place.

3/4” 3/4”

Wall Rail Installation for Wall Cabinets

All wall cabinets except the above fridge cabinet needs wall hanger rails as a support to hang on the wall. Install wall hanger rails according to the layout marked on the wall.

Use lag screws to secure rails to the wall. It is recommended to install a Molly bolt if any end of the the rail is between the wall studs.

When installing wall hangers rails on the wall, it is important to understand the profile of the rail. Always make sure the tapered profile of the wall rail is pointed downwards.

Tapered profile

Mark the required length of wall hanging rails as per your planned layout.

Cut the rails to 3/4” lesser than the marked length using a hacksaw. (Rail can also be bent/ broke by hand at marked lines along rail.)

Wall Rail Installation for Wall Cabinets

Mark a horizontal reference line 2 3/8 “ (60mm)below the measured top line of the wall cabient. Align the center of the hanging rail on this line and mark the holes of wall rail on the wall studs.

Wall Studs

2 3/8”

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

Reference line for

Wall hanger rails

4 Pre drill the markings on wall studs using a

3/32” drill bit.

5 Fix the rails to the wall using 6x70mm lag

Wall Studs

Reference line for

Wall hanger rails

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

60mm (2.36”)

Wall Rail Installation for Wall Cabinets

Use a level to check that each rail is level.

7 Use shims if necessary at the uneven surfaces of the wall.

Level

Wall Studs

Top Line for Wall

Cabinets

Top Line for Wall

Cabinets

Wall Studs

Note

It is recommended to install a Molly bolt if any end of the the rail is between the wall studs.

Mark the hole at the end of the rail to the wall.

2 3/8”

Reference line for

Wall hanger rails

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

Wall Studs

Wall Rail Installation for Wall Cabinets

Wall Studs

Pre drill the marking on wall using a 8mm drill bit.

Install the mollybolt into the hole using a hammer / rubber mallet.

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

Wall Studs

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

Reference line for

Wall hanger rails

11 Remove the screw from the Molly bolt. 12

Install the screw after securing rail to the wall.

Reference line for

Wall hanger rails

60mm (2.36”)

Reference line for

Wall hanger rails

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

Top Line for Wall Cabinets

(84” or 90” from the base level line measured and marked on page 9.)

Wall Cabinets Installation

Note: It is recommended to start installing the corner wall cabinet first and install other wall cabinets on the both sides.

Remove doors of all cabinets before installation. Refer to page 19-21 for removal of doors.

Locate the three wall hanging brackets on the corner wall cabinet. These will be used for hooking onto the hanging rail.

Fully extend all the wall hanging brackets by rotating the screw “A“ counter clockwise. Use the extended philips bit for best results.

Carefully lift and hang the corner cabinet at the corner of the wall on the cabinet hanger rails. Make sure the wall hanging brackets sits on the rail properly.

Two or more people are required to lift/move cabinets into place.

Wall Cabinets Installation

Add shims to the bottom of the cabinet.

Using a level make sure the cabinet is plumb vertically and horizontally from the front to the back and left to right.

Use an exacto knife to cut the shims after installing all the wall cabinets.

Wall cabinets can be adjusted vertically by adjusting the screw noted B in the image below. To fully seat the wall cabinet, ensure screw A is tightened and the cabinet is flush with the wall hanging bracket.

Referencing your design layout, locate the two wall hanging brackets on the next cabinet and ensure they are fully extended.

Fully extend all the wall hanging brackets by rotating the screw “A“ counter clockwise. Use the extended philips bit for best results.

Wall Cabinets Installation

Using two people, carefully lift and hang the cabinet ensuring the wall hanging brackets are securely mounted onto the wall hanging rail. Adjust the cabinet until it is adjacent to the corner cabinet.

Two or more people are required to lift/move cabinets into place.

Place the cabinet horizontally close to the corner cabinet. Add shims to the bottom of the cabinet and place a level on the top to make sure the cabinets are level.

Use an exacto knife to cut the shims after installing all the wall cabinets.

Wall Cabinets Installation

12 Fix both cabinets together to prevent movement using a c-clamp. Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach cabinets together.

2”

13 Cover all the wall hanging brackets with covers provided in the hardware box.

Wall hanging bracket cover

Wall Cabinets Installation

Similarly install other wall cabinets according to the layout and secure cabinets with eachother.

2”

Note: Cabinets must be attached together and attached to the wall. It is recommended to install side panels after attaching all cabinets together. Attach cabinets to the wall after installation of wall side panels.

Wall Cabinets Installation

Install wall side panels near the open end of the cabinets.

Align the side panel to the top. Leave a space of length L on front as shown below to align the side panel with front face of the door.

17 Doors may needed to be installed on the cabinet for the correct measurement “ L ”.

Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach side panels.

2”

Wall Cabinets Installation

Pre-drill a pilot hole (5/32” drill bit) on the back panel of the cabinets at 3/4” from the bottom, aligned with the wall studs. Attach all cabinets to the wall with 6x70mm Lag screw using a power tool.

Pre-drill

3/4”

Lag screws

3/4”

Installing the Above Fridge Cabinet

Parts required

1 Place the fridge cabinet between the two extended side panels.

C - Clamps

Ø4mm X 30mm

Chipboard Screws

Side Panels Drill

Align the side panel to the top and leave a space of length “ L ” on front as shown below to make sure the side panel flushes with the door front face. Doors may needed to be installed on the cabinet for the correct measurement “ L ”.

3 Secure side panels in place using

C-clamps.

4 Make sure the side panels are flush with the top of the cabinet.

Cabinet - Top view

Installing the Above Fridge Cabinet

Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach side panels.

Carefully lift the cabinet and move it next to the wall cabinets according to the layout.

2”

7 Adjust all 4 feet by rotating them to make sure the cabinet is level.

Two or more people are required to lift/move cabinets into place.

Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach cabinets together.

2” 2”

Max. 3/4” adjustable

Pre -drill two pilot holes at 3/4” from bottom and top aligned with the wall studs using a 3/32” drill bit. Screw in the cabinet to the wall stud using the

Ø6x70mm Lag screws provided.

2”

2” 2”

2”

Installing the Wall Cabinet Side Panels

(Installed for the cabinets without under cabinet skirting)

Parts required

1 Use a standard height side panel when under cabinet skirt is not being installed.

C - Clamps

Ø4mm X 30mm

Chipboard Screws

Side Panels Drill

2 Drill in four Ø4mm x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach side panel.

Remove the C-Clamp and follow steps

1 and 2 to install side panels wherever needed.

Installing the Wall Cabinet Side Panels

(Installed for the cabinets with under cabinet skirting)

Parts required

Use side panel for skirting when under cabinet skirt is being installed below the wall cabinets.

C - Clamps

Ø4mm X 30mm

Chipboard Screws

Side Panels Drill

2 Drill in four Ø4mm x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach side panel.

Remove the C-Clamp and follow steps

1 and 2 to install side panels wherever needed.

Installing the Crown Moldings

Parts required

Miter Box Saw

Crown Moldings Drill

Ø3.5mm X 35mm

Chipboard Screws

Cut the crown moldings to required length with an angular cut of 45 degrees at the edges.

Measure the length of cabinets on top to cut a required length of Crown Moldings.

Install Crown Moldings on top of the cabinets.

Drill two pilot holes at each corner and drill in the Ø3.5mm X35mm chipboard screws into the pilot holes.

Installing the Wall cabinet Skirting

Parts required

1 Measure the length of cabinet skirting required under the wall cabinets.

Miter Box Saw

Undermount Skirt Drill

Ø3.5mm X 35mm

Chipboard Screws

2 Cut the cabinet skirting to a required length using a hand saw and a miter box.

4 Place the cabinet skirting under the cabinet between the sidepanels.

5 Drill pilot holes at the corners and drill in the Ø3.5mm X35mm chipboard screws.

Installing the Base Cabinet Side Panels

Parts required

Install side panel near the open end of the cabinets..

C - Clamps

Ø4mm X 30mm

Chipboard Screws

Side Panels Drill

Installing the Base Cabinet Side Panels

Adjust the position of side panel by rotating the feet and make sure the top surface of the panel is flush with the cabinet.

Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach side panel.

2” 2”

2”

Installing the Toe kicks

Parts required

Measure the length of toekicks needed for each set of cabinets and cut the toekick using a hand saw.

Miter Box Saw

Toekick Drill

Ø3.5X16 wood screws

2 Cut the Toekicks to required length using a hand saw and a miter box..

Place toekick closer to the legs and mark the position of legs on to the toekick for installation of feet clamps.

Install feet clamps on the toekicks as per the markings.

A B

Installing the Toe kicks

Push and fit the toekicks to the feet.

6 Make sure the feet clamps are fit properly with the feet.

Installing the Filler piece

Parts required

Ø4mm X 30mm

Chipboard Screws

1 Identify the leftover space between the cabinets and the wall.

Side Panel Drill Saw

2 Measure the space between the wall and the cabinets.

Cut the side panel into three pieces. One with the measured width to cover the space and two with a width of 2”.

W 2” 2”

Wall

Take one of the 2” strips and attach it to the side panel of the cabinet using a

Ø4mmX 30mm chip board screws.

Take the other 2” strip and attach it to the wall aligned with the height of the cabinet using a Ø4mm X 30mm chip board screws.

Installing the Filler piece

5 Apply silicone to the front faces of the panel strips.

5 Attach the filler piece aligned with the cabinet.

Corner Layout Installation

Install doors, drawers and handles of the cabinets after installing all the accessories. Adjust the position of doors and drawer fronts.

Installing the Linear layout

Note: When installing a linear layout, it is recommended to begin the installation with the tallest cabinets, either a pantry or above fridge cabinet. For a linear layout without pantry or above fridge cabinet, begin with a wall cabinet at end.

1 Install leveling legs of the pantry cabinet.

Refer to the page 32 for installation of legs.

Remove the doors of pantry cabinet.

Refer to page 21 for the door removal procedure.

Install Pantry cabinet at the end as per the planned linear layout. Take into consideration the fact that there is a handle and should adjust opening accoringly.

Installing the Linear layout

4 Install the above fridge wall cabinet next to the pantry cabinet. Refer to page 51 for installation of above fridge cabinet along with the side panels.

5 Install cabinet hanger rails on the wall as per the layout. Refer to page 40 for installing the Wall cabinet hanger rails.

Installing the Linear layout

6 Install all wall cabinets, and attach the cabinets to each other. Refer the page 44 to install, attach and level the wall cabinets on the wall.

Remove the doors of all the base cabinets.

Refer to page 19 - 21 for the door removal procedure.

Install leveling legs for all the base cabinets. Refer to the page 32 for installation of legs.

Installing the Linear layout

Install all the base cabinets according to the layout and attach all the adjacent cabinets to each other. Secure all base cabinets to the wall. Refer the pages 37-39 for installing the base cabinets.

Install standard height wall cabinet side panels wherever needed. Refer to the page 53 .

Install extended height wall cabinet side panels wherever needed. Refer to the page 54 .

Installing the Linear layout

Install crown moldings for all the wall cabinets. Refer to the page 55 .

Install cabinet skirtings for all the wall cabinets. Refer to the page 56 .

Install side panels wherever needed for the base cabinets. Refer to the page 57 .

Install toekicks for all the base cabinets.

Refer to the page 59 .

Installing the Island layout

The Island layout can be created by combining base cabinets together (Island) to existing corner or linear layouts. For the installation of linear layout refer the pages 64 - 68 .

For the installation of corner layout refer the pages 35 to 63 .

Linear

Island

Creating a 26” Deep Island

The 26” wide island is constructed by attaching the base cabinets next to eachother.

Parts and Tools required

Chip board screw for

Cabinets

Ø4mm X 30mm

Drill Phillips Bit C - Clamps Toekick Island Side Panels Island Back Panels

Installing the Island layout

Install three base cabinets next to each other and join them using c-clamps.

2”

Fix the cabinets together to prevent movement using a c-clamp. Drill in four Ø4mm x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach cabinets together.

2”

Installing the Island layout

Attach back panels to the rear side of all cabinets and adjust the levelling legs to flush the panels with the top of the cabinet. Make sure to align panels with the sides of the cabinet.

Drill in four Ø4mm x30mm chip board screws at all corners from inside to fix the back panels.

Max. 3/4” adjustable

5 Attach Island side panels and drill in four chipboard screws from inside at all four corners.

Refer to the page 57 for detailed instuctions on installing the side panels.

Installing the Island layout

6 Install toekicks for all the base cabinets. Refer to the page 59 for detailed instuctions on installing the toekicks.

7 Install Custom countertop to finish the Island. NewAge does not offer Countertops for Islands.

Measure the length and with of the cabinet to order custom countertop.

Installing the Island layout

Creating a 40” Deep Island

The 40” wide island is constructed using base cabinets and wall cabinets that are lined up back to back.

Parts and Tools required

1 A set of wall cabinets and base cabinets are needed to create a 40” deep island.

Base Cabinets

Adjustable leg for Wall Cabinets

Chip board screw for

Cabinets

Ø4mm X 30mm

Drill

Wall Cabinets

C - Clamps Toekick Phillips Bit

Extended

Island Side Panels

Island Back Panels

1 Install three base cabinets next to each other and join them using c-clamps.

Drill in four Ø4mmx30mm chip board screws at all corners by leaving a gap of

2inches from the edges to attach cabinets together.

Installing the Island layout

Flip the wall cabinet, pre drill four pilot holes at all four corners of the cabinet base. Fix all four legs to the cabinet using the screws provided.

Install wall cabinets back to the Base cabinets and fix the cabinets together by drilling in four Ø4x30mm chip board screws at all corners by leaving a gap of

2inches from the edges to attach cabinets together.

Attach Extended Island side panels and adjust the levelling legs to flush the panels with the top of the cabinet. Drill in four chipboard screws from inside at all four corners.

Install toekicks for all the base cabinets.

Refer to the page 59 for detailed instuctions on installing the toekicks.

Max. 3/4” adjustable

Installing the Island layout

7 Install custom countertop to finish the Island. NewAge does not offer Countertops for the cabinet Islands. Measure the length and width of the cabinet to order custom countertop.

Installing the U shaped layout

1 Remove doors for all the wall cabinets.

Refer to page 20 .

2 Install rails on the wall and install the corner wall cabinet. Refer to page 40 .

3 Install all the adjacent wall cabinets, make sure the cabinets are level, attach the cabinets together and secure cabinets to the wall. Refer to pages 44 - 48 .

Installing the U shaped layout

Remove the doors of all the base cabinets.

Refer to page 19 - 21 for the door removal procedure.

Install leveling legs for all the base cabinets. Refer to the page 32 for installation of legs.

Install corner base cabinets as shown in the layout with a spacing of 9inches from the wall.

9”

Installing the U shaped layout

7 Install all base cabinets, make sure the cabinets are level, attach cabinets together and secure cabinets to the wall. Refer the pages 35-39 for installing the base cabinets.

8 Install Above fridge cabinet. Refer to page

51 .

Install standard height wall cabinet side panels wherever needed. Refer to the page 53.

Installing the U shaped layout

Install extended height wall cabinet side panels wherever needed. Refer to the page 54 .

Install crown moldings for all the wall cabinets. Refer to the page 55 .

Install cabinet skirtings for all the wall cabinets. Refer to the page 56 .

Install side panels wherever needed for the base cabinets. Refer to the page 57 .

Installing the U shaped layout

Install toekicks for all the base cabinets.

Refer to the page 59 .

Additional Accessories offered by NewAge

LED’s

To Install LED’s refer to the LED Install

Instructions.

Shelves

To Install Shelves refer to the Shelf

Installation guide.

Additional Accessories offered by NewAge

Handles

To Install Door Handles refer to the

Handles Install guide.

Sink

To Install Sink refer to the Home kitchen

Sink Install Instructions.

Granite Countertops

To Install Countertops refer to the Granite

Countertops Install guide.

Spare Parts

SPARE PARTS - BASE CABINET with DOORS

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Toe kick clips x4

Adjustable leg x4

Spare Part

Kit 1

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Hinge 110º x 2

Screws x 4

Spare Part Kit 10

Cabinet Shelf 12”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 22

Cabinet Shelf 18”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 23

Cabinet Shelf 24”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 24

Cabinet Shelf 36”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 25

SPARE PARTS -

BASE CABINET with DOORS

Part #

HKC-169A-01

HKC-170A-01

HKC-174A-01

HKC-178A-01

HKC-194A-01

HKC-195A-01

HKC-196A-01

HKC-197A-01

Description

Levelling Legs

Spare Part Kit 1

Toe Clips

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L - LIH

LIN

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part Kit-10

Hinge 110° With Plate & Two Screws

Spare Part Kit-22

Shelf - 12inch

Shelf Support Bracket

Spare Part Kit-23

Shelf - 18 inch

Shelf Support Bracket

Shelf - 24 inch

Spare Part Kit-24

Shelf Support Bracket

Spare Part Kit-25

Shelf - 24 inch

Shelf Support Bracket

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets

12” & 24” Base

36” Base

Description Item #

12” Door

18” Door

SPARE PARTS - BLIND CORNER

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Toe kick clips x4

Adjustable leg x4

Spare Part

Kit 1

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Hinge 95º x 2

Screws x 4

Spare Part

Kit 14

Blind Corner Shelf

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 9

Part #

HKC-169A-01

HKC-170A-01

HKC-174A-01

HKC-177A-01

HKC-182A-01

SPARE PARTS -

BLIND CORNER

Description

Levelling Legs

Spare Part Kit 1

Toe Clips

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part Kit-9

Shelf - Blind Corner

Shelf Support Bracket

Spare Part Kit-14

Hinge 95° Blind Corner With Two Screws

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

For Door and Blind Corner Filler Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets Description Item #

Blind Corner Filler Filler 27

Blind Corner Door 18” Door 3

SPARE PARTS - 3 DRAWER

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Toe kick clips x4

Adjustable leg x4

Spare Part

Kit 1

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Drawer Stabilizer x 1

Spare Part

Kit 11

Chipboard

Screw x 1

4 x 15.5L

Drawer Front

Connector x 4

Support bar locks x8

Spare Part

Kit 12

Drawer Deep Spacer 550L x 4

Drawer Deep Spacer 550R x 4

Spare Part

Kit 13

Drawer

Shallow

Spare Part

Kit 3

Drawer Deep

Spare Part

Kit 4

SPARE PARTS -

3 DRAWER

Part #

HKC-169A-01

HKC-170A-01

HKC-171A-01

HKC-172A-01

HKC-174A-01

HKC-179A-01

HKC-180A-01

HKC-181A-01

Description

Levelling Legs

Spare Part Kit 1

Toe Clips

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L - LIH

LIN

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-3

Drawer Shallow M550LSet

Spare Part Kit-4

Drawer Deep D550LSet

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part Kit-11

Drawer Stabilizer(Only for 36” Drawers)

Chipboard Screw-PZ2-Thread Dia 4X15.5L

Spare Part Kit-12

Drawer Deep Spacer Support Lock

Drawer Front Connector

Spare Part Kit-13

Drawer Deep Spacer 550L

Drawer Deep Spacer 550R

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

SPARE PARTS -

3 DRAWER

Cabinets

18” 3 Drawer

24” 3 Drawer

36” 3 Drawer

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Description

18in Top Drawer (Panel)

18in Mid/Bottom Drawer (Panel)

24in Top Drawer (Panel)

24in Mid/Bottom Drawer (Panel)

36in Top Drawer (Panel)

36in Mid/Bottom Drawer (Panel)

Item #

SPARE PARTS - SPLIT DRAWER and DOORS

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Toe kick clips x4

Adjustable leg x4

Spare Part

Kit 1

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Hinge 110º x 2

Screws x 4

Spare Part Kit 10

Drawer Stabilizer x 1

Spare Part

Kit 11

Chipboard

Screw x 1

4 x 15.5L

Drawer Front

Connector x 4

Support bar locks x8

Spare Part

Kit 12

Cabinet Shelf 24”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 24

Cabinet Shelf 36”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 25

Drawer

Shallow

Spare Part

Kit 3

Cabinet Shelf 18”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 23

SPARE PARTS - SPLIT

DRAWER and DOORS

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

Part #

HKC-169A-01

HKC-170A-01

HKC-171A-01

HKC-174A-01

HKC-178A-01

HKC-180A-01

HKC-149A-01

HKC-195A-01

Description

Levelling Legs

Spare Part Kit 1

Toe Clips

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L - LIH

LIN

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-3

Drawer Shallow M550LSet

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part Kit-10

Hinge 110° With Plate & Two Screws

Hardware Kit-12

Drawer Stabilizer(Only for 36” Drawers)

Chipboard Screw-PZ2-Thread Dia 4X15.5L

Spare Part Kit-13

Drawer Deep Spacer Support Lock

Drawer Front Connector

Spare Part Kit-23

Shelf - 18 inch

Shelf Support Bracket

XXXXX

SPARE PARTS - SPLIT

DRAWER and DOORS

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

Part #

HKC-196A-01

HKC-197A-01

Description

Shelf - 24 inch

Spare Part Kit-24

Shelf Support Bracket

Spare Part Kit-25

Shelf - 36 inch

Shelf Support Bracket

XXXXX XXXXX XXXXX

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets

12in Split Base (Door)

18in Split Base (Door)

18in Top Drawer (Panel)

24in Top Drawer (Panel)

36in Top Drawer (Panel)

Description

Door

Top Drawer

Item #

SPARE PARTS - PANTRY

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Toe kick clips x4

Adjustable leg x4

Spare Part

Kit 1

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Screws x 4

Hinge 155° x 2

Spare Part

Kit 16

Cabinet Shelf 18”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 23

Cabinet Shelf 24”

X 1

Shelf Support Bracket

X 4

Spare Part

Kit 24

Pantry Fixed Shelf

18” X 1

Tab Shelf

Boss Insert

X 4

Pantry Fixed Shelf

24” X 1

Tab Shelf

Boss Insert

X 4

Tab Shelf

Support

X 4

Spare Part

Kit 26

Euro Screw

6x13.5L

X 4

Tab Shelf

Support

X 4

Spare Part

Kit 27

Euro Screw

6x13.5L

X 4

SPARE PARTS - PANTRY

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

Part #

HKC-169A-01

HKC-170A-01

HKC-174A-01

HKC-184A-01

HKC-196A-01

HKC-198A-01

Description

Levelling Legs

Spare Part Kit 1

Toe Clips

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L - LIH

LIN

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part Kit-16

Hinge 155° With Plate & Two Screws

Shelf - 18 inch

Spare Part Kit-23

Shelf Support Bracket

Spare Part Kit-24

Shelf - 24 inch

Shelf Support Bracket

Spare Part Kit-26

Pantry Fixed Shelf - 18 inch

Tab Shelf Boss Insert

Tab Shelf Support Element

Euro Screw-PZ2 Thread Dia 6X13.5L

XXXXX

36 Inch

SKU

XXXXX

Part #

HKC-199A-01

SPARE PARTS - PANTRY

Description

Spare Part Kit-27

Pantry Fixed Shelf - 24inch

Tab Shelf Boss Insert

Tab Shelf Support Element

Euro Screw-PZ2 Thread Dia 6X13.5L

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets

18in Pantry (Door)

18in Pantry Extended (Door)

24in Pantry (Door)

24in Pantry Extended (Door)

Description

Standard Door

Extended Door

Standard Door

Extended Door

Item #

SPARE PARTS - SINK CABINET

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Toe kick clips x4

Adjustable leg x4

Spare Part

Kit 1

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Hinge 110º x 2

Screws x 4

Spare Part Kit 10

Frame

Component

X 1

Panel

Component

X 1

Euro Screw

X 4

6 x13.5L

Spare Part

Kit 15

SPARE PARTS -

SINK CABINET

Part #

HKC-169A-01

HKC-170A-01

HKC-174A-01

HKC-178A-01

HKC-183A-01

Description

Levelling Legs

Spare Part Kit 1

Toe Clips

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part-10

Hinge 110° With Plate & Two Screws

Spare Part Kit-15

Panel Component Keku

Euro Screw-PZ2 Thread Dia 6X13.5L

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets

12in Split Base (Door)

18in Split Base (Door)

24in Sink False Drawer (Panel)

36in Sink False Drawer (Panel)

Description

Door

Top Drawer

Item #

SPARE PARTS - STANDARD WALL CABINETS

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Spare Part

Kit 5

Wall Cabinet Shelf 12”

X 1

Shelf Support Bracket

X 4

Spare Part Kit 18

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Hinge 110º x 2

Screws x 4

Spare Part Kit 10

Wall Cabinet Shelf 18”

X 1

Shelf Support Bracket

X 4

Spare Part Kit 19

Wall Cabinet Shelf 24”

X 1

Shelf Support Bracket

X 4

Spare Part Kit 20

Wall Cabinet Shelf 36”

X 1

Shelf Support Bracket

X 4

Spare Part Kit 21

SPARE PARTS - STANDARD

WALL CABINETS

Part #

HKC-170A-01

HKC-173A-01

HKC-174A-01

HKC-178A-01

HKC-186A-01

HKC-187A-01

HKC-188A-01

HKC-193A-01

Description

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-5

Wall mounting bracket cover

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part-10

Hinge 110° With Plate & Two Screws

Spare Part Kit-18

12” Wall Cabinet Shelf

Spare Part Kit-19

18” Wall Cabinet Shelf

Spare Part Kit-20

24” Wall Cabinet Shelf

Spare Part Kit-21

36” Wall Cabinet Shelf

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

SPARE PARTS - STANDARD

WALL CABINETS

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets

12” & 24” Wall

36” Wall

Above Fridge Cabinet (Door)

Above Fridge Cabinet Extended (Door)

Above Stove Cabinet (Door)

Above Stove Cabinet Extended (Door)

Description

12” Door

18” Door

Standard Door

Extended Door

Standard Door

Extended Door

Item #

100

SPARE PARTS - CORNER WALL CABINET

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Spare Part

Kit 5

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Hinge 110º x 2

Screws x 4

Spare Part Kit 10

Corner Wall

Cabinet Shelf

X 1

Shelf Support

Bracket

X 5

Spare Part

Kit 30

101

102

SPARE PARTS - CORNER WALL CABINET

Part #

HKC-170A-01

HKC-173A-01

HKC-174A-01

HKC-178A-01

HKC-202A-01

Description

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L - LIH

LIN

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-5

Wall Mounting Bracket Cover RH

Wall Mounting Bracket Cover LH

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part Kit-10

Hinge 110° With Plate & Two Screws

Spare Part Kit-30

Corner Cabinet Shelf

Shelf Support Bracket

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets

Corner Wall Cabinet - A with handle (Door)

Corner Wall Cabinet - B without handle (Door)

Corner Wall Extended Cabinet - A with handle (Door)

Corner Wall Extended Cabinet - B without handle (Door)

Description Item #

Door

SPARE PARTS - GLASS DOOR WALL CABINETS

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Chip board screw for Toe kick Clips

Ø4mm X 40mm x4

Chip board screw for Toe kick Clips

Ø3.5mm X 35mm x4

Molly Bolt x 2

Cover Cap x 4

Chip board screw for

Cabinets

Ø4mm X 30mm x8

Lag Screw

Ø6mm X 70mm x3

Spare Part

Kit 2

Lag Screw

Cover Cap and

Washer x4

Side Panel

Adjustable Leg x2

103

Chip board screw for Toe kick Clips

Ø3.5mm X 16mm x4

Spare Part

Kit 5

Glass Cabinet Shelf 36”

X 1

Shelf Support Bracket

X 5

Spare Part

Kit 28

Door Bumper x2

Tab Shelf

Support

X 4

Euro Screw-

Dia 6X13.5L

Tab Shelf

Boss Insert

X 4

Shelf Support

Bracket x 4

Glass Shelf

Support Bracket

X 4

Spare Part

Kit 6

Shelf Support

Pin X 4

Hinge 110º x 2

Screws x 4

Spare Part Kit 10

Glass Cabinet Shelf 36”

X 1

Shelf Support Bracket

X 5

Spare Part

Kit 29

SPARE PARTS - GLASS DOOR WALL CABINETS

Part #

HKC-170A-01

HKC-173A-01

HKC-174A-01

HKC-178A-01

HKC-200A-01

HKC-201A-01

Description

Spare Part Kit 2

Chipboard Screw-PZ2 Thread Dia 4X30L

Lag Screw-Thread Dia 6X70L

Chipboard Screw-PZ2-Thread Dia 3.5X16L

Chipboard Screw-PZ2-Thread Dia 4X40L - LIH

LIN

Cover Cap - Dia 17 PZ2 Cross Slot

Molly Bolt- HM 6x37 S

Adj Leg- M6x25L With Insert

Cover Cap for Mounting Screw

Chipboard Screw-PZ2-Thread Dia 3.5X35L

Spare Part Kit-5

Wall Mounting Bracket Cover RH

Wall Mounting Bracket Cover LH

Spare Part Kit-6

Shelf Support Pin Dia 4.9x16L

Glass Shelf Support Clip

Euro Screw

Door Bumper

Shelf Support Bracket

Tab Shelf Boss Insert

Tab Shelf Support Element

Spare Part Kit-10

Hinge 110° With Plate & Two Screw

Spare Part Kit-28

Glass Shelf - 24 inch

Glass Shelf Support Clip

Spare Part Kit-29

Glass Shelf - 36 inch

Glass Shelf Support Clip

18 Inch

SKU

XXXXX

24 Inch

SKU

XXXXX

36 Inch

SKU

XXXXX

For Door Replacement

Refer to Door and Drawer Reference Table for SKUs

Cabinets

24” Standard Glass Door Cabinet

36” Standard Glass Door Cabinet

24” Extended Glass Door Cabinet

36” Extended Glass Door Cabinet

Description

12in Glass Door

18in Glass Door

12in Glass Door Extended 30

18in Glass Door Extended 31

Item #

104

DOOR AND DRAWER REFERENCE TABLE

Item

Description

1 12in Base/Wall (Door)

2 12in Split Base (Door)

3 18in Base/Wall (Door)

4 18in Split Base (Door)

5 18in Top Drawer (Panel)

6 24in Top Drawer (Panel)

7 36in Top Drawer (Panel)

White

84200 84400 2000AAA 2000AAB 2000AAC 2000AAD

84202 84402 2002AAA 2002AAB 2002AAC 2002AAD

84204 84404 2004AAA 2004AAB 2004AAC 2004AAD

84206

84208

84209

84210

Gray

84406

84408

84409

84410

Polo Cream

2006AAA 2006AAB

2008AAA 2008AAB

2009AAA 2009AAB

2010AAA 2010AAB

Antique

Blue

2006AAC

2008AAC

2009AAC

2010AAC

Black

2006AAD

2008AAD

2009AAD

2010AAD

8 18in Mid/Bottom Drawer (Panel) 84211 84411 2011AAA 2011AAB 2011AAC 2011AAD

9 24in Mid/Bottom Drawer (Panel) 84212 84412 2012AAA 2012AAB 2012AAC 2012AAD

10 36in Mid/Bottom Drawer (Panel) 84213 84413 2013AAA 2013AAB 2013AAC 2013AAD

11 24in Sink False Drawer (Panel) 84214 84414 2014AAA 2014AAB 2014AAC 2014AAD

12 36in Sink False Drawer (Panel)

13 18in Pantry (Door)

84215

84216

84415

84416

2015AAA 2015AAB

2016AAA 2016AAB

2015AAC

2016AAC

2015AAD

2016AAD

14 18in Pantry Extended (Door)

15 24in Pantry (Door)

84217 84417 2017AAA 2017AAB 2017AAC 2017AAD

84218 84418 2018AAA 2018AAB 2018AAC 2018AAD

84219 84419 2019AAA 2019AAB 2019AAC 2019AAD

84220 84420 2020AAA 2020AAB 2020AAC 2020AAD

84222 84422 2022AAA 2022AAB 2022AAC 2022AAD

16 24in Pantry Extended (Door)

17 Above Fridge Cabinet (Door)

18 Above Fridge Cabinet Extended

(Door)

19 Above Stove Cabinet (Door)

20 Above Stove Cabinet Extended

(Door)

21 12in Wall Cabinet Extended

(Door)

22 18in Wall Cabinet Extended

(Door)

23 Corner Wall Cabinet - A with handle (Door)

24 Corner Wall Cabinet - B without handle (Door)

25 Corner Wall Extended Cabinet - A with handle (Door)

26 Corner Wall Extended Cabinet - B without handle (Door)

27 Blind Corner Filler Panel

28 12in Glass Door

29 18in Glass Door

30 12in Glass Door Extended

31 18in Glass Door Extended

84224

84226

84228

84230

84232

84233

84234

84235

84236

84237

84238

84239

84424

84426

84428

84430

84432

84433

84434

84435

84436

84437

84438

84439

84240 84440

2024AAA 2024AAB

2026AAA 2026AAB

2028AAA 2028AAB

2030AAA 2030AAB

2032AAA 2032AAB

2033AAA 2033AAB

2034AAA 2034AAB

2035AAA 2035AAB

2036AAA 2036AAB

2024AAC

2026AAC

2028AAC

2030AAC

2032AAC

2033AAC

2034AAC

2035AAC

2024AAD

2026AAD

2028AAD

2030AAD

2032AAD

2033AAD

2034AAD

2035AAD

2036AAC 2036AAD

Manufacturer One Year Limited Warranty

When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for a period of One Year from the purchase date of the product.

NEWAGE PRODUCTS INC. WILL NOT PAY FOR:

• Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.

• Damage resulting from products caused by accident, misuse, abuse, fire, flood, improper installation, acts of God, neglect, modification or mishandling.

• Repairs or replacement when your product is used in other than normal, residential use, such as a commercial environment, or handled in anyway inconsistent with the installation instructions included with the product.

• Surfaces damaged due to improper use of chemicals, and detergents.

• Replacement parts for NewAge products outside Canada and the United States.

• Loss due to theft, fire, flood, accident or acts of God.

• Shipping or freight fees to deliver replacement products or to return defective products.

• Any labor costs during the one year limited warranty period.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES

THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW.

Thank you for purchasing a NewAge Product!

Please give us a call or visit online if you have any questions.

Call 1.877.306.8930; e-mail at [email protected]

106

Hello! I am an AI chatbot specifically trained to assist you with the NewAge Products 85827 142.25-in W x 84-in H x 25.5-in D Gray Painted Door and Drawer Wall Fully Assembled Stock Prefabricated Cabinet Installation Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated