GE Appliances Profile 29 Owner's Manual & Installation Manual


Add to my manuals
48 Pages

advertisement

GE Appliances Profile 29 Owner's Manual & Installation Manual | Manualzz

2

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances product, and we think you will too. Among other things, registration of your appliance ensures that we can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner s Manual. You may also mail in the pre-printed registration card included in the packing material.

49-60647-5

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

cleaning.

NOTE

To reduce the risk of fire, explosion, electric shock, or injury when using your refrigerator, follow these basic safety precautions:

Power to the refrigerator cannot be disconnected by any setting on the control panel.

NOTE Repairs must be performed by a qualified

Service Professional.

stand on, or play in or with the appliance.

or mental capabilities or lack of experience and knowledge can use this appliance only if they are supervised or have been given instructions on safe vapors and liquids in the vicinity of this or any other appliance.

cans with a flammable propellant in this appliance.

and similar applications such as: staff kitchen areas catering and similar non-retail applications.

supply is required for automatic icemaker operation.

The water pressure must be between 40 and 120 psi

(275-827 kilopascals).

doors from any refrigerator before disposing of it or discontinuing its use.

To reduce the risk of injury when using your refrigerator, follow these basic safety precautions.

water when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping or dropping.

Tempered glass is designed to shatter into many small pieces if it breaks.

clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

compartment when hands are damp or wet, skin may stick to these extremely cold surfaces.

completely.

contact with the moving parts of the ejector mechanism, or with the heating element that on the automatic ice making mechanism while the refrigerator is plugged in.

Use a sturdy glass when dispensing ice (on models with ice dispenser

STATE OF CALIFORNIA PROPOSITION 65 WARNINGS

This product contains one or more chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

INSTALLATION

EXPLOSION HAZARD

explosion, or death.

READ AND SAVE THESE INSTRUCTIONS

49-60647-5

3

4

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

CONNECTING ELECTRICITY

ELECTRICAL SHOCK HAZARD

Plug into a grounded 3-prong outlet

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard electrical supply is required. This provides the best performance and also prevents overloading house

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

replaced by a qualified service professional with an

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

SUFFOCATION AND ENTRAPMENT HAZARD

IMPORTANT Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous even if they will sit refrigerator, please follow the instructions below to help prevent accidents.

Refrigerant and Foam Disposal

Before You Throw Away Your Old Appliance

Leave the shelves in place so that children may not easily climb inside.

requires special disposal of your appliance. Contact your local authorities for the environmentally safe disposal of your appliance.

49-60647-5

Controls

Not all features are on all models. Your controls may be similar to the following:

The temperature controls are preset in the factory at

37 F (2.8 C) for the refrigerator compartment and 0 F

(-17.8 C) settings.

Touch-LED Dispenser Control

NOTE The refrigerator is shipped with protective film covering the temperature during installation, remove it now.

Tactile LED Dispenser Control

Once the desired temperature has been set, the temperature display will return to the actual refrigerator and may be required. Each time you adjust the controls, allow

24 hours for the refrigerator to reach the temperature you have set.

To change the Refrigerator temperature

Tactile-LED Dispenser Control

The temperature controls can display both the SET temperature as well as the actual temperature in the vary slightly from the SET temperature based on usage and operating environment.

Turning the cooling system off Tactile-LED Dispenser

Control setting until the display flashes (off) will stop cooling setting until the display flashes (off) will stop the

NOTE Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator.

NOTE The refrigerator is shipped with protective film removed during installation, remove it now.

Touch-LED Dispenser Control

To change the temperature, press and release the

REEZER TEMP/FRIDGE TEMP pad. The SET light will come on and the display will show the set temperature. To change the temperature, tap either the or pad until the desired temperature is displayed.

Performance Air Flow System

Touch-LED Dispenser Control

Press and release the FREEZER TEMP/FRIDGE TEMP pad. Press 5 . The display will show OFF . To turn the unit back on, press the FREEZER TEMP/FRIDGE TEMP pad. Press

(3 C) for the refrigerator.

When the unit is turned back on, it will take up to 24 consists of the Air Tower along the back wall of the refrigerator and the Air Tunnel on the bottom portion of

Placing food in front of the louvers on these components will not affect performance. Although the Air Tower and the Air Tunnel can be removed, doing so will affect on-line, 24 hours a day, contact us at contact us at geappliances.ca or call 1.800.561.3344.)

49-60647-5

5

6

Set Features

How it Works

This pad is used to select the following features:

TurboCool , Quick Ice , Door Alarm and Water Filter .

Pressing SET FEATURES repeatedly will cycle through all of the available features and then exit the mode. displaying features currently set.

TurboCool™

(on some models.)

How it Works

TurboCool™ rapidly cools the refrigerator compartment in order to more quickly cool foods. Use

TurboCool™ when adding a large amount of food to the refrigerator compartment, putting away foods after they have been sitting out at room temperature or when putting away

OR if the refrigerator has been without power for an extended period.

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours. The compressor will continue to run until

(1 C), then it will cycle on and off to maintain this setting.

After 8 hours, or if TurboCool™ is pressed again, the refrigerator compartment will return to the original setting.

How to Use

Tactile LED Dispenser Control

Press TurboCool™.

The TurboCool™ temperature display will show Tc

After TurboCool™ is complete, the TurboCool™ indicator light will go out.

Touch-LED Dispenser Controls

Press SET FEATURES . The refrigerator temperature display will show TurboCool ™ and/or Tc . Press ON/OFF .

After TurboCool ™ is complete, the refrigerator compartment will return to the original setting.

NOTES

The refrigerator temperature cannot be changed during

TurboCool ™ .

TurboCool ™ .

When opening the refrigerator door during TurboCool ™ fans will continue to run if they have cycled on.

, the

ClimateKeeper2™

(on some models.)

How it Works

The ClimateKeeper2™ is the industry s most advanced refrigeration system, delivering optimum temperature and humidity performance to keep food garden fresh longer

The ClimateKeeper2™ system features two evaporators on occasion experience fog or small amounts of moisture in the refrigerator compartment. This is normal and may come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired.

This provides two separate cooling systems, and separates the airflow between between the two compartments, which reduces fresh food odor transfer to improve the taste of ice.

The ClimateKeeper2™ system also reduces the number compartments during normal cooling operations.*

This ensures that the humidity levels in the fresh food compartment are significantly higher than in a conventional system,** allowing fresh produce and other unsealed foods to retain their moisture content and freshness longer. Moisture sensitive foods such as fresh fruit, salads, rice, etc., can now be stored on open shelves without excessive moisture loss.

CustomCool™ feature.

ClimateKeeper2™ refrigerators versus conventional units.

49-60647-5

ExpressChill™

(on some models.)

How it Works

The ExpressChill™ feature is a system of dampers, a fan and a temperature thermistor.

The pan is tightly sealed to prevent the pan s temperature from causing temperature fluctuations in the rest of the refrigerator.

The controls for this pan are located in the top of the refrigerator or on the dispenser with the temperature controls.

How to Use

1. Empty the pan. Place the Chill Tray in the pan. Place the items on the tray and close the pan completely.

2. Select the ExpressChill™ pad. On some models, you can then select the chill time (use chart to determine best setting). Other models will only have one option

(45 minutes). On models with multiple settings, tap the pad until the light appears next to the desired setting. it is finished, tap that feature s pad until no options are selected and the display is off.

the display on the controls will count down the time in the cycle.

How to Remove and Replace the Drawer

To remove

1. Pull the drawer out to the stop position.

2. Rotate all four swing locks to the unlock position.

3. Lift the front of the drawer up and out.

To replace

1. Make sure all four swing locks are in the unlock position.

2. Place the sides of the drawer into the drawer supports, making sure the swing locks fit on the drawer slots.

3. L ock all four swing locks by rotating them to the lock position.

ExpressChill™ Chart (on some models)

NOTE Results may vary depending on packaging, starting temperature and other food traits.

15 Minutes

2 Small Juice Boxes

30 Minutes

2 to 6 Beverage Cans of Beverage

4 to 6 Small Juice Boxes

45 Minutes

2 Liters of Beverage

1/2 Gallon of Juice

Gelatin 1 package

ExpressChill™

Wine (750 ml bottle)

49-60647-5

7

8

CustomCool™

(on some models.)

How it Works

The CustomCool™ feature is used to quickly chill items, thaw items or hold the pan at a specific temperature. This feature is a system of dampers, a fan, a temperature thermistor and a heater.

The pan is tightly sealed to prevent temperature fluctuations in the rest of the refrigerator. The controls for this pan are located on the dispenser with the temperature controls.

How to Use

1. Empty the pan. Place the Chill/Thaw tray in the pan. Place the items on the tray and close the pan completely.

2. Touch LED Dispenser Control

Select the ExpressThaw™ , ExpressChill™ or

SelectTemp™ pad. The display and SET light will come on. Tap the pad until the light appears next to the desired setting.

Use the following chart to determine the best setting to use.

ExpressChill can be set to 15, 30 or 45 minutes. The default is 15 minutes.

To stop a feature before it is finished: tap that feature s pad until no options are selected and the display is off.

ExpressThaw and

ExpressChill , the display on the controls will count down the time in the cycle

(on some models).

After the ExpressThaw cycle is complete, the pan will reset to the MEAT

ExpressThaw ™ preserve thawed items until they are used.

The displayed actual temperature of the

CustomCool pan may vary slightly from the

SET temperature based on usage and operating environment.

ExpressChill ™

NOTE reasons, it is recommended that foods be wrapped in plastic wrap when using ExpressThaw . This will help contain meat juices and improve thawing performance.

49-60647-5

CustomCool™

(on some models.)

CustomCool™ Chart

NOTE Results may vary depending on packaging, starting temperature and other food traits.

ExpressThaw

0.5 Lb. (4 hours)

Hamburger Patties (0.5 lb)

1.0 Lb. (6 hours)

Chicken Breasts (1.0 lb)

Ground Beef (1.0 lb)

Steak (1.0 lb)

2.0 Lbs. (10 hours)

Chicken Breasts (2.0 lbs)

Ground Beef (2.0 lbs)

Steak (2.0 lbs)

3.0 Lbs. (12 hours)

Chicken Breasts (3.0 lbs)

Ground Beef (3.0 lbs)

Steak (3.0 lbs)

ExpressChill

15 Minutes

2 Small Juice Boxes

30 Minutes

2 to 6 Beverage Cans of Beverage

4 to 6 Small Juice Boxes

Wine (750 ml bottle)

45 Minutes

2 Liters of Beverage

1/2 Gallon of Juice

Gelatin 1 package

SelectTemp

Citrus Setting (43 F 6 C )

Oranges, Lemons, Limes, Pineapple,

Cantaloupe

Beans, Cucumbers, Tomatoes,

Peppers, Eggplant, Squash

Produce Setting (35 F 2 C )

Pears, Cherries, Blackberries,

Grapes, Plums, Nectarines, Apples

Asparagus, Broccoli, Corn,

Mushrooms, Spinach, Cauliflower,

Meat Setting (32 F 0 C )

49-60647-5

9

10

Water Filter Cartridge - MWF

(On some models)

Water filter cartridge

The water filter cartridge is located in the back upper right corner of the refrigerator compartment.

When to replace the filter on models with a replacement indicator light

There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn orange to tell you that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases.

When to replace the filter on models without a replacement indicator light

The filter cartridge should be replaced every six months or earlier if the flow of water to the dispenser or icemaker decreases.

Removing the filter cartridge

5. Slowly turn it to the right until the filter cartridge stops.

DO NOT OVERTIGHTEN . As you turn the cartridge, it will automatically raise itself into position. The cartridge will move about 1/2 turn.

6. Run water from the dispenser 1-1/2 gallons (about three minutes) to clear the system and prevent sputtering.

7. Press and hold the WATER FILTER pad (on some models) on the dispenser for 3 seconds.

NOTE A newly-installed water filter cartridge may cause water to spurt from the dispenser upon first use.

Filter bypass plug

You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug.

by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

Installing the filter cartridge

Bypass

Plug adapter, it must be removed before installing the cartridge. To remove the adapter, turn it to the left about 1/4 turn.

Bypass

Plug

SmartWater Water by Culligan leave the adapter in place. This adapter will stay in the refrigerator when you replace future cartridges.

To use the filter bypass plug on Water by Culligan™ models, you must first remove the filter adapter from the cartridge holder by turning it to the left.

With adapter Without adapter

(appearance may vary)

Some models use this type of water filter.

2. On models ithout a replacement indicator light, apply the month and year sticker to the new cartridge to remind you to replace the filter in six months.

to allow for better flow from the dispenser immediately after installation.

4.

Line up the arrow on the cartridge and the cartridge holder. Place the top of the new

GE Appliances recommends the use of GE Appliances branded SmartWater™ filters only. Using GE Appliances branded filters in GE Appliances and Hotpoint refrigerators provides optimal performance and reliability.

GE Appliances branded SmartWater™ filters are always the right choice because they are patented and designed specifically for GE Appliances products. SmartWater™ and quality that are important for products that are filtering your water. GE Appliances has not qualified non-GE Appliances branded filters for use in GE

Appliances and Hotpoint refrigerators and there is no assurance that non-GE Appliances branded filters meet

GE Appliances standards for quality, performance and reliability.

com, or call 1.800.GE.CARES (1.800.432.2737).

Replacement filters

it up into the holder.

Cartridge

Holder cartridges, visit our website at www.gewaterfilters.com or call GE Appliances Parts and Accessories,

49-60647-5

Water Filter Cartridge - XWF

(On some models.)

Water Filter Cartridge

The water filter cartridge holder is located in the back upper-right corner of the fresh food refrigerator compartment.

When to Replace the Filter

Filter Bypass Plug

To reduce the risk of property damage due to water leakage, you MUST use the filter bypass plug when a replacement filter cartridge is not available. Some models do not come equipped with the filter bypass plug. To cartridge on the dispenser, the red filter light will start blinking to tell you that you need to replace the filter soon. while you are dispensing until the filter is replaced.

the door is open until the filter is replaced.

cartridge should be replaced every six months, or earlier if the flow of water to the dispenser or icemaker decreases.

Removing the Filter

Canada, call 800.561.3344. The dispenser and icemaker will not operate without either the filter or bypass plug installed. The bypass plug is installed in the same way as a filter cartridge.

Installing the Filter Cartridge in a Side by

Side Refrigerator

1. Line up the arrow on the filter with the arrow on the filter cartridge holder.

Gently push the top of the new filter up inside the holder.

2. Slowly turn the filter to the right until it one: front tabs and gently pulling down.

2. Rotate the filter down.

3. Gently grasp the filter and slowly turn it counterclockwise about a turn. The filter should automatically release itself when you have rotated it far enough to the left. A small amount of water may drip down. the filter cartridge may be ejected as it is removed. Use caution when removing.

you turn the filter, it will automatically raise itself into position. The filter will move about a turn or 90 degrees.

3. Run water from the dispenser for 2 gallons (7.6 liters) or approximately 5 minutes to clear the system. Water may spurt out and air bubbles may be visible during this process.

select models) on the dispenser for three seconds.

Application Guidelines/Water Supply

Water Supply

Water Pressure

Water Temperature

Capacity

0.5 gpm (1.89 lpm)

Potable Water

25-120 psi (172-827 kPa)

170 gallons (643.5 liters)

Sign-up for TEXT REMINDERS by texting

REPLACE to 70543.

To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts during the installation of this product. The disposable filter cartridge should be replaced every 6 months at the rated capacity, or sooner if a noticeable reduction in flow rate occurs.

filters only. Using GE Appliances-branded filters in GE Appliances and Hotpoint refrigerators provides optimal performance and reliability. GE Appliances filters meet rigorous industry standards for safety and quality that are important for products that are filtering your water. GE Appliances has not qualified non-GE Appliances-branded filters for use in GE Appliances and Hotpoint refrigerators and there is no assurance that non-GE Appliancesbranded filters meet GE Appliances standards for quality, performance and reliability.

If you have questions, or to order additional filter cartridges, visit our website at gewaterfilters.com or call GE

Appliances Parts and Accessories, 877.959.8688. (Canada 1.800.661.1616 or GEAppliances.ca/en/products/ parts-filters-accessories)

49-60647-5

11

Shelves and Bins

Not all features are on all models.

Refrigerator Door Bins and Free er Door Tilt-Out Bins

Bins

Snugger bins are adjustable.

To remove Lift the front of the bin straight up, then lift up and out.

To replace or relocate Engage the back side of the bin in the molded supports of the door. Then push down on the front of the bin. Bin will lock in place.

The snugger helps prevent tipping, spilling or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back and forth to fit your needs.

NOTE Be careful when placing items in the top bin.

Make sure that items do not block or fall into the ice chute.

NOTE Part must be in place as shown for proper ice

Refrigerator bin

Top free er bins

12

(on some models)

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves.

To remove Slide the shelf out until it reaches the stop, then press down on the tab and slide the shelf straight out.

To replace or relocate Line the shelf up with the supports and slide it into place. The shelf can be repositioned when the door is at 90 or more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired position, line up with the supports and slide into place.

Make sure you push the shelves all the way back in before you close the door.

Press tab and pull shelf forward to remove

QuickSpace™ Shelf (on some models)

This shelf splits in half and slides under itself for storage of tall items on the shelf below.

This shelf can be removed and replaced or relocated just like Slide-Out Spillproof Shelves.

On some models, this shelf can not be used in the lowest position.

49-60647-5

Shelves and Bins

Not all features are on all models.

Free er Baskets (on some models)

To remove, slide out to the stop position, lift the front past the stop position, and slide out.

Make sure you push the baskets all the way back in before you close the door.

Slide-Out Free er Shelves

To remove, slide out to the stop position, lift the front past the stop position, and slide out from rib.

Make sure you push the shelves all the way back in before you close the door.

Fixed Free er Shelves

NOTE FOR DISPENSER MODELS store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

There are two types of fixed free er shelves.

To remove this type of shelf To remove this type of shelf

1

2

1

2

1. Lift the shelf up at the left side.

2. Bring the shelf out.

1. Lift up the left side of the shelf and slide it left into the center of the shelf supports.

2. Rotate the right side of the shelf up and out of the shelf supports.

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans or one bottle of wine.

The rack hangs from the sides of the dairy bin.

To replace

1. Reattach the rack to the sides of the bin.

2. Engage the back side of the bin in the molded supports on the door. Then push down on the front of the bin.

The bin will lock into place.

To remove

1. Empty the wine/beverage rack.

2. Holding the bottom of the dairy bin, lift the front straight up, then lift up and out.

3. To detach the rack from the dairy bin, pull the rack s side wires out of the holes on each side of the dairy bin.

49-60647-5

13

14

Refrigerator Doors

Refrigerator Doors (on some models)

The refrigerator doors may feel different than the ones you are used to. The special door opening/closing feature makes sure the doors close all the way and are securely sealed.

When opening and closing the door you will notice a stop door will remain open to allow you to load and unload food more easily. When the door is only partially open, it will automatically close.

The resistance you feel at the stop position will be reduced as the door is loaded with food.

Door Alignment

lower it. (A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.)

2. After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

When the door is only partially open, it will automatically close.

Beyond this stop the door will stay open.

Raise

49-60647-5

Crispers and Pans

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the bottom of the drawers should be wiped dry.

On some models, the bottom drawer has full extension slides that allow full access to the drawer.

Adjustable Humidity Crispers

Slide the control all the way to the HI setting to provide high humidity recommended for most vegetables.

Slide the control all the way to the LO setting to provide lower humidity levels recommended for most fruits.

Crisper Removal

Crispers can easily be removed by pulling the drawer straight out and lifting the drawer up and over the stop location.

clearance, the refrigerator will need to be rolled forward until cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out.

Convertible Deli Pan (on some models)

The convertible deli pan has its own cold air duct to or refrigerator compartment to flow to the pan.

The variable temperature control regulates the air flow

Set the control to the coldest setting to store fresh meats.

Set the control to cold to convert the panto normal refrigerator temperature and provide extra vegetable storage space. The cold air duct is turned off. Variable settings between these extremes can be selected.

49-60647-5

15

16

Automatic Icemaker

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemaker

The icemaker will produce seven cubes per cycle approximately 100–130 cubes in a 24-hour period, temperature, number of door openings and other use conditions.

is made to the icemaker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply, set the power switch to the ON position.

Green

Power Light

(on some models)

Special note about dispenser models

(–10 C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the cubes to be joined together.

cloudy, taste stale and shrink.

Avoid contact with the moving parts of the ejector mechanism, or with the heating element

(located on the bottom of the ice maker) that releases tilted out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

To restore your ice level from an empty bucket stage, the following steps are recommended

1. 12 hours after the first batch of ice has fallen into the bin, dispense 3 to 4 cubes.

2. After an additional 6 hours, dispense 3 to 4 cubes again.

These steps will restore your ice level in the shortest amount of time.

NOTE may hear the icemaker cycle multiple times when making one batch of ice.

automatic ice making mechanism while the refrigerator is plugged in.

49-60647-5

Automatic Icemaker

Accessing Ice and Reaching the Power Switch on Dispenser Models

There are two types of ice storage bins on dispenser models.

One has a shelf above the bin, the other does not.

Models with a shelf above the ice bin

To access ice, pull the bin forward.

Special note for models with tilt-out ice bin

Shelf tilted out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

NOTE bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Models with tilt out ice bin

To access ice and reach the icemaker power switch:

1. Lift the bin, then pull it forward until the bin stops.

To reach the power switch, pull the shelf straight out.

Always be sure to replace the shelf.

Shelf

2. Lower the bin to access ice or reach the power switch.

On some models, to access ice or reach the power switch

1. Pull the bin forward until the bin stops.

2. Lower the bin to access ice or reach the power switch.

Removing Ice Bin

(dispenser models)

The ice bin is heavy when full.

Set the power switch to the OFF position before removing the bin.

When replacing the bin, be sure to press it firmly into rotate the drive mechanism 1/4 turn. Then push the bin back again.

49-60647-5

Rotate

Mechanism

17

18

Ice and Water Dispenser

(on some models.)

Using the Dispenser

Select CUBED ice,

CRUSHED ice or WATER .

Press the glass gently against the top of the dispenser cradle.

The spill shelf is not selfdraining. To reduce water spotting, the shelf and its grille should be cleaned regularly.

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a live wire filament. (A burned-out light bulb may break when being replaced.) power to the light circuit.

Dispenser Light

This pad turns the light in the dispenser on and off. The light also comes on when the dispenser cradle is pressed. when the refrigerator is first installed, there may be air in

Spill Shelf the water line system. Press the dispenser arm for at least two minutes to remove trapped air from the water line and to fill the water system. To flush out impurities in the water line, throw away the first six glassfuls of water.

Laceration Ha ard

out, it should be replaced with a 6 watt

Service.

Door Alarm

Use Door Alarm to sound if either door is open for more than 3 minutes. The alarm will stop once the door is closed. the ice crushing blades and lead to serious injury or amputation.

glass may break and result in personal injury.

Locking the Dispenser

Press the LOCK or LOCK CONTROLS pad for 3 seconds to lock the dispenser and control panel. To unlock, press and hold the pad again for 3 seconds.

screen.

Touch LED Dispenser Control

Press the SET FEATURES pad once and DOOR ALARM will blink. Press ON/OFF and the door alarm will be set and the icon will turn solid. Press ON/OFF again to turn the alarm off.

Door Alarm

To set the alarm, press this pad until the indicator light comes on. This alarm will sound if either door is open for more than 3 minutes. The light goes out and the beeping stops when you close the door.

Quick Ice

When you need to speed up ice production, use the Quick Ice feature.

While this feature is turned on, the this period, ice production will increase up to 40 .

Models with the integrated ice feature system require dispensed every 6 to 12 hours. This will help the ice maker fill the bucket properly so that dispensing is better.

How to Use

Touch LED Dispenser Control

Press the SET FEATURES pad twice and QUICK ICE will blink. Press ON/OFF to turn the feature on, then again to turn it off.

Quick Ice

When you need ice in a hurry, press this pad to speed up ice production. This will increase ice production for the following 48 hours or until you press the pad again.

49-60647-5

Ice and Water Dispenser

(on some models)

Precise Fill (on some models)

This water dispenser is equipped with a feature called

3. Press the cup against the cradle and water will begin amount of water (cups or ounces) that you would like set has been dispensed. The display will show the amount of water dispensed, beep, then reset after 5 seconds.

models.

Touch LED Dispenser Control

1. Press the PRECISE FILL CUPS/OZ pad. The

WATER pad will light and the CRUSHED and

CUBED ice pads will turn off. The last unit used will be displayed.

2. Press the PRECISE FILL pad again to toggle between cups and ounces.

If you selected OUNCES, press the or pad to select the number of ounces you would like to have dispensed between 2–99 ounces. The default is 8 ounces.

If you selected CUPS, press the or pad to select the amount you would like to have dispensed.

They are displayed as 1/4, 1/3, 1/2, 2/3 and 3/4, with the highest amount being 16 3/4 cups. The default is

1 cup.

specified amount has been dispensed, just remove the cup from the cradle. The display will show the amount switch is pressed again within that time, the dispenser will return to the set amount.

Important Facts About Your Dispenser

Avoid overfilling glass with ice and use of narrow glasses. Backed-up ice can jam the chute or cause the chute, poke it through with a wooden spoon.

Beverages and foods should not be quick-chilled in the ice storage drawer. Cans, bottles or food packages in the storage drawer may cause the icemaker or auger to jam.

To keep dispensed ice from missing the glass, put the glass close to, but not touching, the dispenser opening.

Some crushed ice may be dispensed even though you selected CUBED ice. This happens occasionally when a few cubes accidentally get directed to the crusher.

After crushed ice is dispensed, some water may drip from the chute.

Sometimes a small mound of snow will form on the door in the ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly. The snow will eventually evaporate.

49-60647-5

19

20

Care and Cleaning

Cleaning the Outside

The dispenser drip area, beneath the grille, should be wiped dry. Water left in this area may leave deposits.

Remove the deposits by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose enough to rinse away.

The dispenser cradle.

Before cleaning, lock the dispenser by pressing and holding the LOCK CONTROLS or LOCK pad for 3 seconds. Clean with warm water and baking soda solution about a tablespoon (15 ml) of baking soda to a quart (1 l) of water. Rinse thoroughly and wipe dry.

The door handles and trim.

Clean with a cloth

The stainless steel doors and door handles (on some models) can be cleaned with a commercially available stainless steel cleaner. Cleaners with oxalic acid such tarnish and small blemishes. Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge. steel.

Keep the outside clean.

Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish wet towel. These may leave a residue that can erode bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of baking

Unplug the refrigerator before cleaning. practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.

Use warm water and baking soda solution about a tablespoon (15 ml) of baking soda to a quart (1 liter) of wipe dry.

Use of any cleaning solution other than that which is recommended, especially those that contain petroleum distillates, can crack or damage the interior of the refrigerator.

with warm water when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact such as bumping or dropping.

Tempered glass is designed to shatter into many small pieces if it breaks.

dishwasher.

The chill/thaw tray is dishwasher safe.

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.

Pull the refrigerator straight out and return it to position by pushing it straight in. Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator.

When pushing the refrigerator back, make sure you don t roll over the power cord or icemaker supply line (on some models).

49-60647-5

Care and Cleaning

Preparing for Vacation

unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the O and shut off the water supply to the refrigerator.

qualified servicer drain the water supply system (on some models) to prevent serious property damage due to flooding.

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage.

When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during moving.

Replacing the Light Bulbs (on some models)

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a live wire filament. (A burned-out light bulb may break when being replaced.)

Refrigerator Compartment—Upper Light

1. Unplug the refrigerator.

2. The bulbs are located at the top of the compartment, inside the light shield. On some models, a screw at the front of the light shield will have to be removed.

On other models, the screw is located in the pocket located at the back of the shield.

3. To remove the light shield, on some models, press in on the tabs on the sides of the shield and slide forward and out. On other models, just slide the shield forward and out.

4. After replacing the bulb with an appliance bulb of the same or lower wattage, replace the light shield and screw. When replacing the light shield, make sure that the tabs at the back of the shield fit into the slots at the back of the light shield housing.

5. Plug the refrigerator back in.

Your light shield will look like one of the following:

OR

Tabs

Pocket

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

1. Unplug the refrigerator.

2. Remove the convertible meat drawer control knob

(on some models) by pulling straight out.

3. Lift the light shield up and pull it out.

4. After replacing the bulb with an appliance bulb of the same or lower wattage, replace the shield.

5. Plug the refrigerator back in.

49-60647-5

21

22

Care and Cleaning

Replacing the Light Bulbs (on some models)

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a live wire filament. (A burned-out light bulb may break when being replaced.)

Refrigerator Compartment—On models with LED lighting

the fresh food compartment and in the rear and side of

Appliances Service at 1.800.432.2737 in the United

States or 1.800.561.3344 in Canada.

Lighting

Free er Compartment

1. Unplug the refrigerator.

2. Remove the shelf just above the light shield. (The shelf will be easier to remove if it is emptied first.) On some models, a screw at the top of the light shield will need to be removed.

3. To remove the light shield, press in on the sides, and lift up and out.

4. Replace the bulb with an appliance bulb of the same or lower wattage, and reinstall the light shield. When reinstalling the light shield, make sure the top tabs snap securely into place. Replace the screw (on some models).

5. Reinstall the shelf and plug the refrigerator back in.

Dispenser (on some models)

1. Unplug the refrigerator.

2. The bulb is located on the dispenser under the control panel. Remove the light bulb by turning it counterclockwise.

wattage.

4. Plug the refrigerator back in.

Lighting

49-60647-5

Installation Instructions

Installation Instructions

Refrigerator Models 22, 23,

25, 26, 27 & 29

Questions Call 800.GE.CARES (800.432.2737) or visit our Website at GEAppliances.com

In Canada, call 1.800.561.3344 or visit our Website at www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT

Save these instructions for local inspector s use

IMPORTANT

Observe all governing codes and ordinances.

Note to Installer – Be sure to leave these instructions with the Consumer.

Note to Consumer – future reference.

Skill level – basic mechanical skills.

Completion time –

30 minutes

30 minutes

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

PREPARATION

WATER SUPPLY TO THE ICEMAKER

(on some models)

be connected to a cold water line. A GE Appliances water supply kit is available at extra cost from your dealer, by visiting our Website at GEAppliances.

com (in Canada, at geappliances.ca

), or from

Parts and Accessories, 877.959.8688. (in Canada

1.800.661.1616).

TOOLS YOU WILL NEED

the base grille (see Step 2 in Moving the Refrigerator),

Phillips Head Screwdriver

49-60647-5

23

24

Installation Instructions

MOVING THE REFRIGERATOR

Lifting Ha ard

Single person lift can cause injury. Use assistance when handling, moving or lifting the refrigerator doors.

NOTE When moving door, to prevent damage to door and electronics carefully place the door in a proper location.

To eliminate the risk of electric shock or injury during installation, you must first follow these instructions can result in electrical shock.

2

REMOVE THE BASE GRILLE

Remove the grille by removing the two

Phillips head screws.

1

LOADING THE REFRIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until the refrigerator is in its final location.

To move the refrigerator, use a padded hand truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

doors must be removed. Proceed to Step 3.

DO NOT remove the handles.

.

49-60647-5

Installation Instructions

MOVING THE REFRIGERATOR (Cont.)

3

DISCONNECT THE WATER

COUPLING (on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into the disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White collar

5

DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors (harnesses) from the cabinet into the bottom hinge on the refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

Bottom hinge

4

DISCONNECT THE POWER

COUPLING (on some models)

If the refrigerator has a water dispenser , there is a power line (harness) from the cabinet must be disconnected.

To disconnect, pull apart at the coupling.

Bottom refrigerator hinge

6

CLOSE THE FREEZER AND

REFRIGERATOR DOORS

Bottom hinge

49-60647-5

25

Installation Instructions

MOVING THE REFRIGERATOR (Cont.)

7

REMOVE THE FREEZER DOOR

instructions, leaving off parts, or overtightening screws, can lead to the door falling off and result in injury and property damage.

A up or by prying it off with a plastic putty knife.

8

REMOVE THE REFRIGERATOR

DOOR

A instructions, leaving off parts, or overtightening screws, can lead to the door falling off and result in injury and property damage.

Remove the refrigerator door top hinge cover (if up or by prying it off with a plastic putty knife.

then lift the hinge straight up to free the hinge pin.

B then lift the hinge straight up to free the hinge pin.

C

C Open the refrigerator door to 90 .

90 and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

90

26

E

90

Set the door on a non-scratching surface with the inside up.

49-60647-5

Installation Instructions

MOVING THE REFRIGERATOR (Cont.)

8

REMOVE THE REFRIGERATOR

DOOR (Cont.)

Lift the refrigerator door up and off the bottom hinge.

person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

9

REPLACING THE DOORS

instructions, leaving off parts, or overtightening screws, can lead to the door falling off and result in injury and property damage.

To replace the doors, simply reverse steps 3 through 8.

However, please note the following

When lowering the doors onto the bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

When connecting the water line, make sure you insert the tubing all the way to the mark.

90

Refreshment Center Models only

E Set the door on a non-scratching surface with the inside up.

Mark placing the doors on the bottom hinges.

When connecting the power line and the electrical lines (refreshment center models only), be sure that the connectors are seated together fully.

49-60647-5

27

28

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

it will not run often enough to maintain proper temperatures.

it will not perform properly.

to water (rain, etc.) or direct sunlight.

loaded.

DIMENSIONS AND SPECIFICATIONS

(for 23' CustomStyle

models)

(91.4 cm)

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:

Sides

Top

Back

23 /25

CustomStyle ™

23 (33 wide),

25 , 26 , 27 , 29

DIMENSIONS AND SPECIFICATIONS

(for 25' CustomStyle

models)

DIMENSIONS AND

SPECIFICATIONS

Water Electrical

Cabinet

Airspace

Plates)

Countertop

72 1 4

(91.4 cm)

* 72 refrigerator have doors that are flush to the top of the opening for the refrigerator, then an additional cabinet doors to open freely.

49-60647-5

Installation Instructions

INSTALLING THE REFRIGERATOR (Cont.)

1

CONNECTING THE

REFRIGERATOR TO THE HOUSE

WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic not a cold water supply, you will need to provide

C hold it in position. You may need to pry open the clamp.

Tubing Clamp

Compression Nut

(sleeve)

NOTES

Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator s water valve.

™ Refrigerator

Refrigerator

Connection

SmartConnect ™ Tubing

Option 2

A

B plastic tube to install filter.

If you are using copper tubing, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the SmartConnect ™ tubing, the nuts are already assembled to the tubing.

If you are using copper tubing, insert the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible.

While holding the tubing, tighten the fitting.

If you are using SmartConnect ™ tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

Connect to potable water supply only.

A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

ELECTRIC SHOCK

HAZARD

NOT drill into the refrigerator.

SmartConnect™

Tubing

Refrigerator

Connection

Option 3

TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

3

PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure the icemaker power switch is set to the position.

See the grounding information attached to the power cord.

49-60647-5

29

30

Installation Instructions

INSTALLING THE REFRIGERATOR (Cont.)

4

PUT THE REFRIGERATOR IN

PLACE

Move the refrigerator to its final location.

5

LEVEL THE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.

5

LEVEL THE REFRIGERATOR

(cont.)

To adjust the rollers on 23 /25

CustomStyle

models

Turn the front roller adjusting screws clockwise to raise the refrigerator, counterclockwise to lower or an adjustable wrench.

Roller adjusting screws

These models also have rear adjustable rollers so you can align the refrigerator with with extension to turn the screws for the rear rollers clockwise to raise the refrigerator, counterclockwise to lower it.

Rollers Raise

Rollers have three purposes

Rollers adjust so the door closes easily when opened about halfway. (Raise the front about

Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble.

Rollers allow you to move the refrigerator away from the wall for cleaning.

To adjust the rollers on 23 (33 wide),

25 , 26 , 27 and 29 models

Turn the roller adjusting screws clockwise to raise the refrigerator, counterclockwise to lower an adjustable wrench.

6

A

LEVEL THE DOORS

Adjust the refrigerator door to make the doors even at the top.

B To align screw to the right to raise the door, to the left to lower it.

NOTE

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Raise

Roller adjusting screw

49-60647-5

Installation Instructions

INSTALLING THE REFRIGERATOR (Cont.)

7

REPLACE THE BASE GRILLE

Replace the grille by installing the two Phillips head screws.

9

START THE ICEMAKER

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate bin.

Power switch

8

SET THE CONTROLS

Set the controls to the recommended setting.

Power switch

NOTE valve may turn on up to 3 times to deliver enough water to the icemaker.

49-60647-5

31

32

Installation Instructions

INSTALLING THE WATER LINE (Icemaker & dispenser models)

BEFORE YOU BEGIN WHAT YOU WILL NEED

tubing you need. Approved plastic water supply lines are SmartConnect™ Refrigerator Tubing

When connecting your refrigerator to a Reverse

Osmosis Water System, the only approved other reverse osmosis water systems, follow the manufacturer s recommendations.

Copper or SmartConnect™ Refrigerator Tubing kit, ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

available in the following lengths: the refrigerator s filter bypass plug. Using the refrigerator s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes and slower water flow from the water dispenser.

This water line installation is not warranted by expensive water damage.

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line.

water line, make sure the icemaker power switch is in the o

Connect to potable water supply only.

A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).

When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the

All installations must be in accordance with local plumbing code requirements.

49-60647-5

Installation Instructions

INSTALLING THE WATER LINE (Cont.)

WHAT YOU WILL NEED (Cont.)

NOTE The only GE Appliances approved plastic tubing is that supplied in SmartConnect™ water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.

A GE Appliances water supply kit (containing tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or from

Parts and Accessories, 877.959.8688 (in Canada

1.800.661.1616).

A cold water supply. The water pressure must be between 20 and 120 p.s.i. (1.4–8.1 bar).

Power drill.

drinking water line.

1

SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

2

CHOOSE THE VALVE

LOCATION

Choose a location for the valve that is easily a vertical water pipe. When it is necessary to connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

1/2 or adjustable wrench.

Straight and Phillips blade screwdriver.

Two 1/4 outer diameter compression nuts and two ferrules (sleeves) to connect the copper tubing to the shutoff valve and the refrigerator water valve.

OR

If you are using a SmartConnect™ Refrigerator

Tubing kit, the necessary fittings are preassembled to the tubing.

3

DRILL THE HOLE FOR THE

VALVE

a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression

Refrigerator tubing.

Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet point of connection to the COLD WATER LINE .

Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

ice production or smaller cubes.

49-60647-5

33

34

Installation Instructions

INSTALLING THE WATER LINE (Cont.)

4

FASTEN THE SHUTOFF VALVE

with the pipe clamp.

Pipe Clamp

Saddle-Type

Shutoff Valve

Vertical Cold Water Pipe

NOTE Commonwealth of Massachusetts

Plumbing Codes 248CMR shall be adhered to.

Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

7

CONNECT THE TUBING TO THE

VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench.

Overtightening may cause leaks.

Saddle-Type

Shutoff Valve Compression Nut

SmartConnect ™ Tubing

5

TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell.

NOTE tubing.

Washer

Pipe Clamp

Clamp

Screw

Packing Nut

Outlet Valve

NOTE Commonwealth of Massachusetts

Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

8

FLUSH OUT THE TUBING

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water off at the water valve after about one quart (1 liter) of water has been flushed through the tubing.

6

ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

NOTE Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

To complete the installation of the refrigerator, go

49-60647-5

Trim kits and decorator panels

models

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels. You can order pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories, 800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4 (6 mm) thick

3/4 (19 mm) or Raised Panel

clearance.

Weight limitations for custom panels:

Clearance

Handle Side

Appearance

Panel

Thick Backing

(19 mm)

Refrigerator

49-60647-5

35

Trim kits and decorator panels

23 Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

Free er Panel

Without Dispenser

Free er Panel

With Dispenser

Cutout Cutout

(8 mm) (8 mm)

17 7 8

(45.4 cm)

36

67 9 32

(170.9 cm)

FRONT

14 15 32

(36.8 cm)

FRONT

14 15 32

(36.8 cm)

33 5 8

(85.4 cm)

25 CustomStyle

Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

Free er Panel

Without Dispenser

Free er Panel

With Dispenser

Cutout Cutout

(8 mm) (8 mm)

(43.2 cm)

(175.3 cm)

FRONT

14 15 32

(36.8 cm)

FRONT

14 15 32

(36.8 cm)

36 1 4

(92.0 cm)

Fresh Food Panel

Cutout

(8 mm)

67 9 32

(170.9 cm)

FRONT

19 15 32

(49.5 cm)

Fresh Food Panel

Cutout

(8 mm)

(175.3 cm)

FRONT

19 15 32

(49.5 cm)

49-60647-5

Inserting the door panels

Read these instructions completely and carefully.

1. Insert the Free er Panel and Fresh Food Panel.

behind the door handle. Push the filler panel (required with some door panels) in behind the decorator panel. Repeat for fresh food panel.

2. Insert the Bottom Free er Panel (on dispenser models).

Carefully push the panel in until it slides into the slot behind the door handle. Push the filler panel (required with some door panels) in behind the decorator panel.

3. Attach the Top Trim on the Free er and Fresh Food Doors.

The Top Trim can be found inside the refrigerator compartment.

Hand tighten only. Make sure that the top of each panel fits snugly behind the lip of the Top Trim.

With a T-20 Torxdriver, attach the Top Trim, using two screws on each Top Trim piece, to the top of each door.

Top Trim Screws

Cut-Out

Cut-Out

Top

Panel

Panel

Bottom

Panel

Side Trim

Side Trim

49-60647-5

37

38

Inserting the door panels

4. Install the Side Trim.

These pieces are tucked inside the refrigerator door handle.

Side Trim until the Side Trim is installed.

Hold the Side Trim against the front face of the decorator panels and fit the Side Trim under the Top Trim. Make sure the magnetically attached Side Trim is fitted correctly and that you are satisfied with the appearance of all the parts.

illustrated.

Top Trim

Side

Trim

Side

Trim

Bottom Trim

49-60647-5

Troubleshooting Tips...

Normal Operating Conditions

Newer refrigerators sound different from older refrigerators.

Modern refrigerators have more features and use newer technology.

Do you hear what I hear These conditions are normal.

HUMMM...

WHOOSH...

The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a high-pitched hum or pulsating sound while it is operating.

Sometimes the refrigerator runs for an extended period, especially when the doors are opened frequently. This means that the Frost Guard™

You may hear the fans spinning at high speeds.

This happens when the refrigerator is first plugged in, when the doors are opened frequently or when a large amount of food is added to the refrigerator maintain the correct temperatures.

improve food preservation.

refrigerator.

hear the fans come on in order to cool the light bulbs.

The fans change speeds in order to provide optimal cooling and energy savings.

You may hear the fans running after selecting

QuickFree e™ or one of the CustomCool™ settings.

CLICKS, POPS,

CRACKS and CHIRPS

You may hear cracking or popping sounds when the refrigerator is first plugged in. This happens as the refrigerator cools to the correct temperature.

Electronic dampers click open and closed to provide optimal cooling and energy savings.

The compressor may cause a clicking or chirping sound when attempting to restart (this could take up to 5 minutes).

The electronic control board may cause a clicking sound when relays activate to control refrigerator components.

Expansion and contraction of cooling coils during and after defrost can cause a cracking or popping sound.

On models with an icemaker, after an icemaking cycle, you may hear the ice cubes dropping into the ice bucket.

WATER SOUNDS

The flow of refrigerant through the cooling coils may make a gurgling noise like boiling water.

Water dropping on the defrost heater can cause defrost cycle.

A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan.

Closing the door may cause a gurgling sound due to and dispenser operating sounds, see the

About the automatic icemaker and About the ice and water dispenser sections.

49-60647-5

39

40

Troubleshooting Tips...

Before you call for service

Save time and money Review the charts on the following pages first and you may not need to call for service.

Problem

Refrigerator does not operate

Possible Causes

Refrigerator in defrost cycle.

Either or both controls set to OFF

Refrigerator is unplugged.

The fuse is blown/circuit breaker is tripped.

Refrigerator is in showroom mode.

Rollers need adjusting.

What To Do

Wait about 30 minutes for defrost cycle to end.

Set the controls to a temperature setting.

Push the plug completely into the outlet.

Replace fuse or reset the breaker.

Unplug the refrigerator and plug it back in.

Vibration or rattling (slight vibration is normal)

Motor operates for long periods or cycles on and off frequently. (Modern refrigerators with more storage space and a larger free er require more operating time. They start and stop often to maintain even temperatures.)

Refrigerator or free er compartment too warm

Frost or ice crystals on fro en food (frost within package is normal)

Divider between refrigerator and free er compartments feels warm

Automatic icemaker does not work

Ice cubes have odor/taste Ice storage bin needs cleaning.

Small or hollow cubes

Slow ice cube free ing

Food transmitting odor/taste to ice cubes.

Interior of refrigerator needs cleaning.

Water filter clogged.

Door left open.

Temperature control not set cold enough.

Frequent “bu ing sound Icemaker power switch is in the 1

(on) position, but the water supply to the refrigerator has not been connected.

Orange glow in free er Defrost heater is on.

See Rollers.

Normal when refrigerator is first plugged in.

Often occurs when large amounts of food are placed in refrigerator.

Door left open.

Hot weather or frequent door openings.

Temperature controls set at the coldest setting.

Temperature control not set cold enough.

Warm weather or frequent door openings.

Door left open.

Door left open.

Too frequent or too long door openings.

Automatic energy saver system circulates warm liquid around front edge of free er compartment.

Icemaker power switch is in the OFF position.

Water supply turned off or not connected.

Free er compartment too warm.

Piled up cubes in the storage bin cause icemaker to shut off.

Ice cubes stuck in icemaker.

Wait 24 hours for the refrigerator to completely cool down.

This is normal.

Check to see if package is holding door open.

This is normal.

See Controls.

See Controls.

Set the temperature control one step colder. See Controls.

Check to see if package is holding door open.

Check to see if package is holding door open.

This helps prevent condensation on the outside.

Slide the power switch to the ON position.

Wait 24 hours for the refrigerator to completely cool down.

Level cubes by hand.

Turn off the icemaker, remove cubes and turn the icemaker back on.

Wrap foods well.

See Care and cleaning.

Replace filter cartridge with new cartridge or with plug.

Check to see if package is holding door open.

See Controls.

(on) position will damage the water valve.

This is normal.

49-60647-5

Troubleshooting Tips...

Before you call for service

Problem

Cube dispenser does not work (on some models)

Possible Causes

Icemaker or water supply turned off.

Ice cubes are fro en to icemaker feeler arm.

An item is blocking or has fallen into the ice chute inside the top bin of the free er.

Irregular ice clumps in storage container.

What To Do

Turn on icemaker or water supply.

Remove cubes.

Remove any item that might be blocking, or has fallen into the chute.

Break up with fingertip pressure and discard remaining clumps.

Water has poor taste/odor (on some models)

Water in first glass is warm

(on some models)

Water dispenser does not work (on some models)

Water spurting from

Water is not dispensed (on some models) but icemaker is working

No water or ice cube production

CUBED ice was selected but

CRUSHED ice was dispensed

(on some models)

Refrigerator has odor

Dispenser is LOCKED.

a colder setting, one position at a time, until clumps do not form.

Press and hold the Lock or Lock Controls pad for 3 seconds.

Water dispenser has not been used for a long time.

Normal when refrigerator is first installed

Water dispenser has not been used for a long time.

Water system has been drained.

Wait 24 hours for the refrigerator to completely cool down.

Allow several hours for replenished supply to chill.

Water supply line turned off or not connected.

Water filter clogged.

Replace filter cartridge or remove filter and install plug.

Air may be trapped in the water system.

Press the dispenser arm for at least two minutes.

Dispenser is LOCKED.

Newly-installed filter cartridge.

Press and hold the Lock or Lock Controls pad for 3 seconds.

Run water from the dispenser for 3 minutes (about 1 1 gallons).

/

2

Water in reservoir is fro en.

Call for service.

Refrigerator control setting is too cold.

Set to a warmer setting.

Supply line or shutoff valve is clogged.

Water filter clogged.

Dispenser is LOCKED.

Last setting was CRUSHED ice.

Foods transmitting odor to refrigerator.

Call a plumber.

Replace filter cartridge or remove filter and install plug.

Press and hold the Lock pad for 3 seconds.

A few cubes were left in the crusher from the previous setting. This is normal.

replace every three months.

See Care and cleaning.

Wipe surface dry. Moisture forms on outside of refrigerator

Moisture collects inside (in humid weather, air carries moisture into refrigerator when doors are opened)

Interior light does not work

Interior needs cleaning.

Not unusual during periods of high humidity.

Too frequent or too long door openings.

Due to the higher himidity in the refrigerator, you may on occasion experience fog or small amounts of moisture in the refrigerator compartment

No power at outlet.

Light bulb burned out.

For LED lights

This is normal for the beverage center.

This is normal and may come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired.

Replace fuse or reset the breaker.

See Replacing the light bulbs.

Call Service.

49-60647-5

41

42

Troubleshooting Tips...

Before you call for service

Problem

Water on kitchen floor or on bottom of free er

Hot air from bottom of refrigerator

Refrigerator never shuts off but the temperatures are OK

Refrigerator is beeping

Door not closing properly

Actual temperature not equal to Set temperature

Food isn t thawing/chilling

Possible Causes

Cubes jammed in chute.

Normal air flow cooling motor. In the refrigeration process, it is normal that heat be expelled in the area under the refrigerator. Some floor coverings are sensitive and will discolor at these normal and safe temperatures.

Adaptive defrost keeps compressor running during door openings.

Door is open.

Door gasket on hinge side sticking or folding over.

A door bin is hitting a shelf inside the refrigerator.

Unit just plugged in.

Door open for too long

Warm food added to refrigerator

Defrost cycle is in process

Packaging.

Wrong weight selected.

Item with high fat content.

Not using Chill/Thaw tray.

SelectTemp or Beverage

Center feature is not working

Move the door bin up one position.

Select a larger weight.

Select a larger weight.

Place items on tray and allow space in between items for better airflow.

Refrigerator compartment temperature control is set at warmest setting.

Beverage Center feature turns off after six months of continuous operation.

the SelectTemp and Beverage Center features are disabled when the refrigerator temperature control is set at the warmest setting.

Press Beverage Center pad to restart.

This is normal.

While QuickFree e™ is enabled, the actual free er temperature may drop as low as –3 F (–19 C)

What To Do

Poke ice through with a wooden spoon.

This is normal. The refrigerator will cycle off after the door remains closed for 2 hours.

Close door.

Apply petroleum jelly on face of gasket

49-60647-5

Refrigerator Limited Warranty

GEAppliances.com

For US Customers, technician. To schedule service online, visit us at www.geappliances.com

, or call GE Appliances at 800.GE.CARES (800.432.2737). Please have your serial number and your model number available when calling for service. In Canada, call 800.561.3344.

Servicing your refrigerator may require the use of the onboard data port for diagnostics. This gives a GE Appliances

Factory Service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be sent to GE Appliances, please advise your technician NOT to submit the data to GE Appliances at the time of service.

For the Period of GE Appliances Will Replace

GE, GE PROFILE and C FE MODELS

One Year purchase

Any part of the refrigerator which fails due to a defect in materials or workmanship. limited one-year warranty, GE Appliances will also provide, free of charge, all labor and related service to replace the defective part.

Thirty Days

(Water filter, if included)

Any part of the water filter cartridge which fails due to a defect in materials or workmanship.

limited thirty-day warranty, GE Appliances will also provide, free of charge , a replacement water filter cartridge.

date of the refrigerator

GE PROFILE and C FE MODELS ONLY

Five Years Any part of the sealed refrigerating system (the compressor, condenser, evaporator an all connecting tubing) which fails due to a defect in materials or workmanship.

imited five-year sealed refrigerating system warranty, GE Appliances will also provide, free of charge, all labor and related service to replace the defective part in the sealed refrigerating system.

What GE Appliances Will Not Cover

Service trips to your home to teach you how to use the product.

filter. used for other than the intended purpose or used commercially.

breakers.

blemishes not reported within 48 hours of delivery.

to water pressure that is outside the specified operating range or due to excessive sediment in the water supply.

cartridge, if included, other than as noted above.

or acts of God.

defects with this appliance.

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

For US Customers This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state s Attorney General.

Warrantor GE Appliances, a Haier company

Louisville, KY 40225

For Customers in Canada This limited warranty is extended to the original purchaser and any succeeding owner for products

Warrantor Canada MC Commercial Inc., Burlington Ontario, L7R 5B6

49-60647-5

43

44

Water Filter Cartridge Limited Warranty

Contact us at geapplianceparts.com

, or call 800.GE.CARES.

For the period of GE Appliances will replace

Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or workmanship during this limited thirty-day warranty.

* of the original purchase

What GE Appliances will not cover

Service trips to your home to teach you how to use the product.

Replacement of house fuses or resetting of circuit breakers.

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is part exchange as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to six months or the shortest period allowed by law.

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state s Attorney General.

For Purchases Made In Iowa This form must be signed and dated by the buyer and seller prior to the consummation of this sale.

This form should be retained on file by the seller for a minimum of two years.

Buyer

Name

Address

City

Signature

State Zip

Seller

Name

Address

City

Signature

State Zip a new or, at our option, a rebuilt part without charge. Return the defective part to the parts supplier from whom it was purchased together with a liable for consequential damages.

Warrantor GE Appliances, a Haier

Louisville, KY 40225 company

49-60647-5

SmartWater ™

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

The following pharmaceutical reduction claims have not been certified by NSF International or the state of California.

Claims tested and verified by independent laboratory

Contaminant

Reduction

Atenolol

Progesterone

Trimethoprim

Average

Influent

978 ng/L

907 ng/l

885 ng/L

1097 ng/L

415 ng/L

NSF specified

Challenge

Concentration

N/A

N/A

N/A

N/A

N/A

Avg %

Reduction

99.5

99.4

94.1

99.5

99.5

Average

Product Water

Concentration

5.0 ng/L

5.4 ng/L

52.3 ng/L

5.0 ng/L

2.0 ng/L

Max Permissible

Product Water

Concentration

N/A

N/A

N/A

N/A

N/A

NSF Reduction

Requirements

N/A

N/A

N/A

N/A

N/A

NSF

Test Report

J-00121587

J-00121587

J-00121588

J-00121589

J-00121587

Application Guidelines/Water Supply Parameters

Water Supply

0.5 gpm (21.9 lpm)

Potable Water

Water Pressure

Water Temperature

40-120 psi (276-827 kPa)

NOTE While the testing was performed under standard laboratory conditions, actual performance may vary. Contaminant reduction testing is conducted every five years by certifying agency to maintain certification.

elements please call 1.877.959.8688 or visit our website at www.geapplianceparts.com.

To reduce the risk associated with ingestion of contaminants

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before and after the system.

Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

REPLACEMENT

ELEMENT claims specified on the performance data sheet.

49-60647-5

NOTICE

To reduce the risk associated with property damage due to water leakage

Read and follow use instructions before installation and use of this system.

MUST comply with all state and local plumbing codes.

Do not your water pressure exceeds 80 psi (552 kPa), you must install a pressure-limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.

Do not water hammer conditions exist you must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition.

Do not install on hot water supply lines. The maximum operating

Protect filter from free ing.

The disposable filter cartridge should be replaced every 6 months at the rated capacity, or sooner if a noticeable reduction in flow rate occurs.

45

Performance Data Sheet

Model GE Appliances XWF

sheet and at iapmort.org.

Substance Tested for Reduction concentration

(mg/L)

Chlorine Taste and Odor

Chloramine Taste and Odor

Cysts

Lead

Mercury

Asbestos

At least 10,000/mL

50,000/L

0.15

0.006

107 to 108 fibers/ L

Toxaphene

VOC (Chloroform surrogate chemical) 0.300

Alachlor 0.050

0.100

Carbofuran carbon tetrachloride chloropicrin

0.081

0.190

0.078

0.077

0.015

0.110

0.052

0.08

1,2-dichloroethane

1,1-dichloroethylene cis-1,2-dichloroethylene trans-1,2-dichloroethylene

1,2-dichloropropane cis-1,3-dichloropropylene dinoseb

Endrin bromochloroacetonitrile dibromoacetonitrile

0.040

0.088

0.083

0.170

0.086

0.080

0.079

0.170

0.053

0.088

0.044

0.022

0.024

dichloroacetonitrile trichloroacetonitrile

1,1-dichloro-2-propanone

1,1,1-trichloro-2-propanone heptachlor (H-34, Heptox) heptachlor epoxide hexachlorobutadiene hexachlorocyclopentadiene

Lindane methoxychlor pentachlorophenol

Styrene

1,1,2,2-tetrachloroethane

Tetrachloroethylene

Toluene

2,4,5-TP (silvex) tribromoacetic acid

1,1,1-trichloroethane

1,1,2-trichloroethane trichloroethylene bromoform bromodichloromethane chlorodibromomethane xylenes

Meprobamate

Atenolol

0.078

0.270

0.042

0.160

0.084

0.150

0.180

0.300

0.300

0.300

0.070

0.060

0.055

0.050

0.096

0.120

0.150

0.081

0.081

0.0096

0.015

0.0072

0.0082

0.025

0.0107

0.044

Metolachlor

Trimethoprim

Linuron

TCEP

TCPP

Phenytoin

Naproxen

Estrone

Bisphenol A

Nonyl phenol

46

Avg

Reduction

96.9

96.9

95

95

>99

95.5

95.9

98.6

98.6

98.7

96.1

96.6

> 99

99

> 98

> 99

95

> 99

> 99

95

98.1

98.1

96

95.9

96.5

97.1

99.1

97.3

> 99

> 99

> 99

> 99

> 97

> 99

> 99

> 99

98

98

99

96

>99

98

> 98

> 99

> 98

95

> 99

> 99

> 99

> 99

> 99

99

99

> 99

> 99

98

98

> 97

> 99

> 99

98

> 99

99

98

> 99

91.4

>99.99

98.85

96.3

>99

86.95

99.7

> 98

Maximum permissible product water concentration (mg/L)

N/A

0.5

0.015

0.015

0.001

60

30

200

200

200

20

20

0.001

0.0016

0.001

0.0005

0.0046

0.0005

0.0010

0.015

20

20

300

200

700

700

30

60

0.0002

0.0003

0.0001

0.0003

0.00001

0.0002

0.001

0.000002

0.00001

0.0001

0.001

0.004

0.0005

0.001

0.001

0.001

0.001

0.0048

0.001

0.0005

0.001

0.001

0.001

0.0002

0.00059

0.001

0.00002

0.0005

0.0006

0.003

0.001

0.001

0.0018

0.001

0.0002

0.0017

0.00002

N/A

N/A

0.01

0.002

N/A

0.003

0.015

0.001

Application Guidelines/Water Supply Parameters

Water Supply

Water Pressure

Water Temperature

Capacity

0.5 gpm (1.89 lpm)

Potable Water

25-120 psi (172-827 kPa)

170 gallons (643.5 liters) maintenance and filter replacement requirements be carried out for the information.

NOTE While the testing was performed under standard laboratory conditions, actual performance may vary. replacement elements please call 1.877.959.8688 or visit our website at gewaterfilters.com

.

To reduce the risk associated with ingestion of contaminants

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before and after the system.

Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

NOTICE

To reduce the risk of water leakage or flooding, and to ensure optimal filter performance

Read and follow use instructions before installation and use of this system.

MUST comply with all state and local plumbing codes.

Do not install if water pressure exceeds 120 psi (827 must install a pressure-limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.

Do not install where water hammer conditions may occur. must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition.

Do not install on hot water supply lines. The maximum

(38 C).

Protect filter from free ing.

Change the disposable filter cartridge every six months or sooner if you observe a noticeable reduction in water flow rate.

recommended intervals may lead to reduced filter performance and cracks in the filter housing, causing water leakage or flooding.

53 and 401 for the reduction of the substances listed below.

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the

XWF System is certified by IAPMO R&T against NSF/ANSI Standards 42,53, and 401 for the reduction of claims specified on the performance data sheet and at iapmort.org.

49-60647-5

Notes

49-60647-5

47

Consumer Support

GE Appliances Website

Have a question or need assistance with your appliance Try the GE Appliances Website 24 hours a day, any day of the year

You can also shop for more great GE Appliances products and take advantage of all our on-line support services designed for

GEAppliances.com GEAppliances.ca

Register Your Appliance

Register your new appliance on-line at your convenience Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty, should the need arise. You may also mail in the pre-printed registration card included in the packing material.

GEAppliances.com/register

Prodsupport.mabe.ca/crm/Products/ProductRegistration.aspx

Schedule Service

Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at your

GEAppliances.com/service or call 800.432.2737 during normal business hours.

GEAppliances.ca/en/support/service-request or call 800.561.3344

Extended Warranties

Purchase a GE Appliances extended warranty and learn about special discounts that are available while your warranty is still

GEAppliances.com/extended-warranty or call 800.626.2224 during normal business hours.

GEAppliances.ca/en/support/purchase-extended-warranty or call 866.277.9842

Parts and Accessories

GEApplianceparts.com

or by phone at 877.959.8688 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

website at GEAppliances.ca/en/products/parts-filters-accessories or call 800.661.1616.

Contact Us

your phone number, or write to:

GEAppliances.com/contact

GEAppliances.ca/en/contact-us

Printed in United States

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement