Litheli U1PS21000 Operator's Manual

Add to my manuals
18 Pages

advertisement

Litheli U1PS21000 Operator's Manual | Manualzz

Operator's Manual

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

40V BATTERY POWERED

POLE SAW

U1PS21000

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Visit our website at: http://www.litheli.com

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please contact us: WWW.LITHELI.COM

No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of LITHELI.

Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Table of Contents

Safety .............................................................. 2

Specifications ................................................ 5

Assembly ........................................................ 10

Operation ....................................................... 12

Maintenance .................................................. 14

Parts List and Diagram .............................. 16

Warranty ........................................................ 18

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INSTRUCTIONS

When using electric gardening appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:

READ ALL INSTRUCTIONS

Gardening Appliance Safety

1.

Avoid Dangerous Environment -

Do not use appliances in damp or wet locations.

8.

Don’t grasp the exposed cutting blades or cutting edges when picking up or holding the appliance.

2.

Do Not Use In Rain.

3.

Keep Children Away - All visitors should be kept at a distance from work area.

4.

9.

Do Not Force Appliance - It will do the job better and with less likelihood of injury at the rate for which it was designed.

jewelry. They can be caught in moving parts.

Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.

10.

Do not Overreach -

Keep proper footing and balance at all times.

11.

common sense. Do not operate appliance when you are tired.

5.

6.

7.

Wear ANSI-approved safety goggles, hard hat and heavy-duty rubber work gloves. Use face or dust mask if operation is dusty.

Use Right Appliance - Do not use appliance for any job except that for which it is intended.

Avoid Unintentional Starting -

Do not carry appliance with finger on switch.

12.

When not in use, appliances should be stored indoors in dry, and high or locked-up place - out of reach of children.

13.

Maintain Appliance With Care Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Keep handles dry, clean, and free from oil and grease.

Page 2 WWW.LITHELI.COM

Item U1PS21000

14. Check Damaged Parts - Before further use of the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation.

A guard or other part that is damaged should be properly repaired or replacedby a qualified technician unless indicated elsewhere in this manual.

15. Wear full eye protection and protective clothing.

16. If electrolyte contacts the skin, wash it off immediately with water.

17. If electrolyte contacts the eyes, flush thoroughly and immediately with water. Seek medical attention.

18.

Stop working when you feel tired or exhausted.

Make regular breaks to rest.

19.

DANGER! People with pacemakers should not use pole saws. Pole saws produce strong electromagnetic fields that can cause pacemaker interference or pacemaker failure. People with pacemakers should consult their physician(s) for advice.

20.

When servicing use only identical replacement parts.

21.

Disconnect Appliance - Remove Battery Pack when not in use, before servicing, when changing accessories such as blades, and the like.

22.

Carefully follow cutting procedures explained in this manual. They are specifically planned to reduce risk to the operator.

23.

Lock pole in place securely before using Pole

Saw.

Lithium Battery Safety Warnings

LITHIUM BATTERIES STORE

A LARGE AMOUNT OF ENERGY AND

WILL VENT FIRE OR EXPLODE IF MISTREATED:

1. Keep

Battery Pack dry.

d. Puncture, e. Incinerate, f. Expose to temperatures greater than 104°F.

2. DO NOT DO ANY OF THE FOLLOWING

TO THE BATTERY PACK: a. Open, b. Drop, c. Short-circuit,

Battery Charger Safety

3. Charge Battery Pack only according to its Charger’s instructions.

4. Inspect Battery Pack before every use; do not use or charge if damaged.

1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instruction for battery charger Mode U1PS21000.

6. Remove or disconnect battery after use, before servicing, cleaning or removing material from the gardening appliance.

2. Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product using battery.

7. Do not dispose of battery in a fire. The cell may explode. Check with local codes for possible disposal instructions.

3. CAUTION - To reduce risk of injury, charge only li-ion type rechargeable batteries. Other types of batteries may burst causing personal injury and damage.

8. Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

4. Do not charge or use appliance in rain, or in wet locations.

9. Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

5. Do not use battery-operated appliance in rain.

Item U1PS21000 WWW.LITHELI.COM

Page 3

Vibration Hazard

This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:

1.

Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or

Raynaud’s Disease should not use this appliance. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.

3. Wear suitable gloves to reduce the vibration effects on the user.

4. Use appliances with the lowest vibration when there is a choice between different processes.

5. Include vibration-free periods each day of work.

6. Grip appliance as lightly as possible

(while still keeping safe control of it).

Let the appliance do the work.

7. To reduce vibration, maintain the appliance as explained in this manual. If any abnormal vibration occurs, stop use immediately.

Pole Saw Safety

1.

Keep all parts of the body away from saw chain. Do not remove cut material or hold material to be cut when saw chain is moving.

Make sure the switch is off when clearing jammed material. Saw chain continues to move after the switch is turned off. A moment of inattention while operating the pole saw may result in serious personal injury.

2.

Carry the pole saw by the handle with the saw the pole saw, always fit the saw chain device cover. Proper handling of the pole saw will reduce possible personal injury from the saw chain.

6.

Always use two hands when operating the pole saw. Hold the pole saw with both hands to avoid loss of control.

7.

Always use head protection when operating the pole saw overhead. Falling debris can result in serious personal injury.

8.

Keep handles dry, clean, and free from oil and grease.

9.

Do not touch guide bar tip to any object.

Tip contact may cause guide bar to move suddenly upward and backwards.

10.

Do not operate Pole Saw from within a tree.

Operation of tool while up in a tree may result in personal injury.

3.

Hold Pole Saw by insulated gripping surfaces only, because the saw chain may contact hidden wiring. Saw chains contacting a “live” wire may make exposed metal parts of the pole sw “live” and could give the operator an electric shock.

11.

Keep proper footing and operate the garden power tool only when standing on fixed,

4.

5.

Do not use the pole saw in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.

To reduce the risk of electrocution, never with or use near power lines may cause serious injury or electric shock resulting in death.

surfaces such as ladders may cause a loss of balance or control of the garden power tool.

12.

When cutting a limb that is under tension, be alert for spring back. wood fibers is released, the limb may strike the operator and/or throw the tool out of control.

13.

Do not use for bore cutting, felling or bucking.

14.

Keep bystanders and other workers at least

50 feet from the work area.

15.

Do not operate within 50 feet of electrical lines.

Page 4 WWW.LITHELI.COM

Item U1PS21000

16.

Use extreme caution when cutting brush the saw chain and be whipped around.

17.

Follow instructions for lubricating, chain tensioning and changing accessories.

Improperly tensioned or lubricated chain may either break or increase the chance for kickback.

18.

Kickback is the result of tool misuse and/or incorrect operating procedures or conditions.

Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut.

Kickback can be avoided by taking proper precautions as given below: a.

Maintain a firm grip, with thumbs and fingers encircling the Pole Saw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken.

Do not let go of the garden power tool.

b.

Do not overreach. This helps prevent unintended tip contact and enables better control of the garden power tool in unexpected situations. c. Only use replacement bars and chains specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or kickback.

d. Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback.

19. Use for cutting wood only. Do not use for cutting plastic, masonry or non-wood building materials.

20. The battery Charger gets hot during

use. The Charger’s heat can build up

to unsafe levels and create a fire

hazard if it does not receive adequate ventilation,due to an electrical fault, or if it is used in ahot environment.

Do not place the Charger on a flammable surface. Do not obstruct any vents on the

Charger.

Especially avoid placing the Charger on carpets and rugs; they are not only flammable, but they also obstruct vents under the Charger.

Place the Charger on a stable, solid, nonflammable surface (such as a stable metal workbench or concrete floor) at least 1 foot away from all flammable objects, such as drapes or walls. Keep a fire extinguisher and a smoke detector in the area. Frequently monitor the

Charger and Battery Pack while charging.

21.

Maintain labels and nameplates on the appliance.

These carry important safety information.

If unreadable or missing, contact Litheli for a replacement.

22.

The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.

It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Specifications

Charger Input Rating 120VAC / 60Hz

Charger Output Rating 36VDC / 3.3A

Battery Rating

Battery Type

40VDC / 2.5Ah / 90Wh

40V Litheli Li-Ion

Chain Speed

Saw Chain

4.5m/s 10%

Oregon 10 in

Item U1PS21000

WWW.LITHELI.COM

Page 5

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING:

Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the charger. Do not use the charger if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

Extension Cords

Note: Extension cords must not be used with this item’s Charger.

Symbology

Double Insulated

V

Volts

~

Alternating Current

A

Amperes

n0 xxxx/min.

No Load Revolutions per Minute (RPM)

WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields.

Read the manual before set-up and/or use.

WARNING marking concerning Risk of Fire.

Do not cover Charger ventilation ducts.

Charge on fireproof surface only.

WARNING marking concerning

Risk of Electric Shock.

Properly connect Charger’s power cord to appropriate outlet.

WARNING marking concerning

Risk of Explosion.

Do not puncture, short, or open battery packs and do not charge damaged battery packs.

Charge level indication.

Do not throw the batteries in the household waste, fire or water.

Indication of the noise level LWA in dB.

Do not expose the battery to sunlight for a long time and do not place it on radiators (max. 45 ° C).

Dispose of the batteries at a collection point for old batteries, from where they are taken to environmentally friendly recycling.

Charge level indication.

Page 6 WWW.LITHELI.COM

Item U1PS21000

Setup -Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages, refer to Parts

List and Diagram on page 14.

Functions

Saw

Chain

Lock knob

Guide

Bar

Oil Filler

Cap

Chain Cover

Button Drive

Cover

Extension

Lock

-

-

22.5°

22.5°

45°

Trigger

Safety

Lock

Item U1PS21000

Trigger

WWW.LITHELI.COM

Page 7

Charging the Battery Pack

NOTE : The Battery Pack comes partly charged.

Charge the Battery Pack prior to first use, ideally at least 60 minutes.

Always pull out the Power Plug of the Charger from the mains before removing or connecting the Battery Pack to the charger.

Never charge the Battery Pack when the ambient temperature is below 10 °C or above 40 °C.

Rest the Charger for at least 15 minutes between successive charging sessions.

If no Battery Pack is inserted into the Charger and the charger is connected to mains, the Charging Status LED flashes green.

1 . Align the Battery Pack to the rails of the

Charger and slide it in. Ensure it clicks noticeably in place.

2. Connect the Power Plug of the Charger with the mains. The Charging Status LED lights up red. The continuously lit green

Charging Status LED indicates that the charging process is complete.

3. Disconnect the Power Plug of the

Charger from the mains and remove the

Battery Pack from the charger.

4. Attach the Battery Pack back to the product (see “Installing and Removing

Battery Pack”).

Power Cord with Plug

Rapid Battery Charger

Battery

Pack

Connector

Charging

Status

LED – Green

Charging

Status

LED – Red

Charging status LEDs

Green LED flashes without battery pack

Green LED lights up with battery pack

Charger ready

Battery pack fully charged

Red LED lights up with battery pack

Battery pack charging

Red and green LEDs flashing

Red and green LEDs continuously lit

Battery pack defect

Battery pack too cold or warm

Page 8 WWW.LITHELI.COM

Item U1PS21000

Checking the Battery Charging Level

NOTE : Press the Battery Level Button to check the charging level of the Battery Pack. The charging level will be shown on the Battery Level Indication Lights.

Battery Pack

Charge the Battery Pack before operation when it is at 25% or low battery charging level.

Release

Button

Battery Level

Indication Lights

Battery

Level Button

LED status Charging level

Charging level too low

Between 5% and 50%.

Between 50% and 80%.

More than 80%.

Item U1PS21000 WWW.LITHELI.COM

Page 9

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Release the Trigger and remove Battery Pack before assembling or making any adjustments.

Install Guide Bar and Saw Chain

CAUTION!

Wear heavy-duty work gloves when handling Saw Chain.

1.

BEFORE FIRST USE: and chain oil(purchased by yourself) overnight.

2.

Rotate the Lock Knob and then remove the

Drive Cover.

4.

Place Saw Chain around Drive Sprocket, place

Guide Bar’s lower oil hole over Tension Pin.

Drive

Sprocket

Tightening

Knob

Lock Knob

Drive

Cover

3.

Slide Saw Chain’s drive links into Guide Bar’s groove, making sure chain is installed in correct rotation direction.

Guide

Bar

Drive

Link

Groove

Rotation

Direction

Symbol

Tension

Pin

5.

Tighten the chain by tightening the knob to reach the usable state.

6.

Replace Drive Cover, then tighten Drive Cover

Lock Knob.

7.

Tension Saw Chain according to Tension Saw

Chain on page 10.

Page 10 WWW.LITHELI.COM

Item U1PS21000

Tension Saw Chain

CAUTION! Wear heavy-duty work gloves when handling Saw Chain.

NOTICE: To prevent damage to Saw Chain, do not tension hot chain. Let chain cool before tensioning.

Check tension: a. Before every use.

b. Often during first half hour of use. c. Periodically during use.

1. Snap Test: Pull Saw Chain away from bottom of Guide Bar, then let go. Saw Chain should snap back to its original position, solidly contacting bottom of Guide Bar.

2. Pull Saw Chain by hand around Guide Bar several times, it should feel snug and move freely around Guide Bar.

3. Adjust tension as necessary by tightening or loosening Tensioning Screw, then repeating steps 1. and 2., until proper tension is achieved.

Fill Automatic Oiler Reservoir

NOTICE: full. Do not operate Pole Saw without oil. Do not put used oil in Reservoir.

4.

Replace Oil Fill Cap and tighten.

the Saw Chain during operation.

Fill Oiler Reservoir:

Oil Fill

Cap a. Before every use.

b. When oil level reaches MIN mark on Oil

Level Gauge.

1. Remove Oil Fill Cap.

MAX

MIN

2. Using funnel, fill tank with bar and chain oil

(purchased by yourself).

3. Use clean cloth to remove excess oil.

Oil Level

Gauge

Attach Shoulder Strap

1. If desired, change location of Shoulder Strap

Connector by loosening Hex Bolt, moving

Connector, then tightening Hex Bolt securely.

2. Clip Shoulder Strap into hole on Connector.

Shoulder Strap

Connector

Hex Bolt

Adjust Pole Saw Length

1. With Pole Saw parallel to ground, move

Extension Lock to unlocked position.

2. Pull on motor housing to expose extension pole. Pull out to desired length, then move

Extension Lock to locked position until it clicks into place.

Unlocked

Locked

Motor

Housing

Extension

Lock

WARNING! To prevent serious injury, check

Extension Lock for tightness periodically during use.

Item U1PS21000

WWW.LITHELI.COM

Page 11

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

• Before operating the gardening appliance, put on ANSI-approved safety goggles, hard hat and other safety gear. Safety goggles and other safety gear need to be purchased by yourself.

Charging Battery Pack

1.

Place Battery Charger on a dry, flat, fireproof surface indoors.

Note: Allow battery to cool completely before charging.

2.

Examine Battery Pack. Do not charge a cracked, open, or leaking Battery Pack, or charge a non-recommended type of Battery

Pack.

3.

Battery Pack is designed to fit this Charger specifically. If Battery Pack does not fit

Charger properly, do not try to insert it.

Do not force Battery Pack into the Charger.

4.

Plug Charger into a grounded, 120VAC, 60Hz receptacle. Green LED will blink, showing that power is supplied to the charger.

5.

Slide Battery Pack onto Charger. Red LED will light continuously while charging.

Note: A fully discharged Battery Pack will take about 1 hour to fully charge.

Note: While charging, Battery Pack and Charger may become warm to the touch and the Charger ′ s fan may come on. This is normal.

6.

Green LED will light continuously when Battery

Pack is charged. Unplug Charger and remove

Battery Pack when finished.

7.

Allow Battery Pack to cool completely before use.

Installing and and Removing Battery Pack

1.

To install: Slide Battery Pack into slot on handle until it clicks into place.

2.

To remove: Press both Battery Pack Release

Buttons and pull Battery Pack out of slot.

Workpiece and Work Area Set Up

Battery

Pack

Battery Pack

Release

Button

1.

Designate a work area that is clean and well lit.

The work area must not allow access by children or pets to prevent distraction and injury.

2.

There must not be objects, such as utility lines, nearby that will present a hazard while working.

Page 12 WWW.LITHELI.COM

Item U1PS21000

Operation

TO PREVENT SERIOUS INJURY AND DEATH:

• Wear ANSI-approved safety goggles, hard hat and steel-toed boots during use.

• Avoid kick back. Do not touch Guide Bar tip to any object. Tip contact may cause guide bar to move suddenly upward and backwards.

• Do not operate Saw with one hand.

Only hold Pole Saw with both hands. Do not stand directly under branch being cut.

• Only stand on fixed, secure and level surface.

• Do not operate within 50 feet of electrical lines.

BEFORE EVERY USE: a.

Check oil level, add oil as necessary (see Fill

Automatic Oiler Reservoir on page 10).

b.

Run Pole Saw at half throttle for several minutes (see step 3. below).

c.

Stop motor and remove Battery Pack .

Let chain cool, then check tension and adjust as necessary (see Tension

Saw Chain on page 10). d.

Make sure Saw Chain is sharp. e.

Make sure Automatic Oiler is distributing oil.

DURING EVERY USE: a.

Check tension often during the first half hour of use and periodically during

4. Maintain a firm grip, with thumbs and fingers encircling the Pole Saw’s handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces.

Auxiliary

Handle

Main

Handle

Tension Saw Chain on page 10).

b.

Check oil level every 10 minutes of use. Fill oil reservoir when oil level reaches MIN mark

5. Hold the Pole Saw to the side of your body at maximum 60° from horizontal. Do not overreach.

Oiler Reservoir on page 10).

1.

Loosen Shoulder Strap, then place over shoulder. Tighten Shoulder Strap, making sure shoulder pad is on top of shoulder.

2.

Adjust Pole Saw length as desired.

3.

To start, push and hold Trigger Safety

Lock, then squeeze and hold Trigger.

Release Trigger Safety Lock.

To stop, release Trigger.

Trigger

Safety Lock

Trigger

6. Make sure Saw is running at full speed before starting a cut.

7. Cut lower branches first.

8. Do not force Pole Saw, let Pole Saw do the work.

9. Remove the Pole Saw from a cut while it is running.

Item U1PS21000 WWW.LITHELI.COM

Page 13

the saw and get away from where the saw and branch are likely to fall immediately.

Cutting Long Branches: a.

Make first cut 4" to 6" from end of branch. b.

Make next cuts 4" to 6" from the previous cuts, working toward the trunk.

5

4

3

2

1

Cutting Thick Branches: c.

Make first cut 6" away from trunk, on underside, 1/3 way into branch.

d.

Make second cut 2" away. Sever branch from the top. e.

Make third cut close to the trunk, on underside, 1/3 way into branch. f.

Make fourth cut from top, severing branch.

10. When finished: a. Release Trigger and remove Battery Pack. extension pole to return to normal position on its own. Extension pole is is spring loaded.

b. With Pole Saw parallel to ground, move Extension Lock to unlocked position. Pull extension pole back in, then move Extension Lock to locked position until it clicks into place. c.

Clean, then store according to Cleaning,

Maintenance and Lubrication on page 14.

User-Maintenance and Storage

Procedures not specifically explained in this manual must be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK:

Release the Trigger and remove the Battery Pack before performing any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment.

If abnormal noise or vibration occurs, have the problem corrected before further use.

Page 14 WWW.LITHELI.COM

Item U1PS21000

Cleaning, Maintenance and Lubrication

1.

2.

BEFORE EACH USE, condition of the tool. Check for:

• leaking, swollen, or cracked battery pack,

• loose hardware

inspect the general

• misalignment or binding of moving parts

• cracked or broken parts

• dull or damaged Saw Chain

• any other condition that may affect its safe operation.

BEFORE EACH USE, tension Saw Chain and add bar and chain oil to oil reservoir.

3.

PERIODICALLY OR WHEN REPLACING SAW

CHAIN, turn the GuideBar over to distribute the wear on it.

Replace theGuide Bar when bent, cracked, or when the Saw Chain moves excessively from side to side on the Guide Bar due to wear (see

Determining Guide Bar Wear on page 13).

4.

AFTER USE: a. Remove Drive Cover, Saw Chain and Guide Bar. b. Scrape debris loose from inside Drive Cover and around Drive Sprocket, then wipe with clean cloth and mild soap and water. Do not use solvents. Do not immerse tool in liquid .

c. Remove sawdust and sap from the

Guide Bar’s Groove using a bar groove cleaning tool (purchased by yourself). d. Wipe Guide Bar with clean cloth, including oil passages, then lubricate with bar and chain oil. e. Wipe debris from Saw Chain, then lubricate with bar and chain oil. f. Replace Guide Bar, Saw Chain and Drive

Cover, leave Saw Chain loose during storage. g. Clean outside surfaces with a clean, dry cloth. If necessary use mild soap and water. h. Place Chain Cover over Saw Chain, then Store Pole Saw in a dry, secure location away from children.

5.

Li-Ion BATTERY MUST BE RECYCLED OR

DISPOSED OF PROPERLY. Do not short, incinerate or open battery.

Sharpening/Replacing Saw Chain

1. Have the cutters sharpened by a qualified technician when: a. The sawdust becomes powder-like.

b. You can’t make the cut without extra force.

c. The Pole Saw does not cut straight.

d. Vibration increases.

Replacing Drive Sprocket

2. A Saw Chain that is damaged or too worn to be restored by sharpening will need to be replaced.

Have the Drive Sprocket replaced by a qualified technician when the Saw Chain is replaced.

Determining Guide Bar Wear

The rails of the Guide Bar groove should always be parallel to each other. Place a ruler along the side of the Guide Bar and Saw Chain. If there is a gap, the bar is normal.

Ruler

Saw

Chain

Rail

Gap

Straight

Guide Bar

If the ruler is flush with the Guide Bar and

Saw Chain, or the Chain tilts to one side, then the

Guide Bar is worn and needs to be replaced.

Tilting Saw

Chain

Ruler

Worn

Guide Bar

Item U1PS21000

WWW.LITHELI.COM

Page 15

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES

ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO

MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF

THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL

REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED

TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT

OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING

OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Part Description

1 Inner plum pan head tapping screw

2 Inner plum pan head tapping screw

3 Left handle

4 40V discharge plate assembly

5 Insert holder

6 Trigger

7 Internal conductor

8 Cable platen

9 Trigger safety lock

10 Switch self-lock spring

11 Self-lock push button spring

12 Inching switch

13 Right handle

14 Bracelet

15 Glass fiber tube

16 Hook sleeve

17 Locating sleeve

18 Hex lock nut

19 Socket roundhead dental screw

20 Sponge casing

21 Socket roundhead dental screw

22 Extension lock

23 Pipe pin

24 Lock sleeve

25 Hexagonal aluminium tube

26 Spring wire

27 Lock sleeve cover

28

Cross recessed countersunk head tapping screw

29 Limit block

30 Lock sleeve

31 Inner plum pan head tapping screw

32 Rod plug Right

33 Rod plug Left

34 Power socket

35 Button

36 Button spring

37 Rotating arm Right

38 Socket

39 Rotary arm Left

40 Anti-jamming PCB assembly

41 Absorbing pad

42 887 Motor

Record Product’s Serial Number Here:

1

1

1

2

1

1

4

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Qty

1

26

2

4

2

4

4

2

2

1

2

2

2

1

1

2

1

2

Part Description

43 Central support

Qty

1

44 Cross recessed small panhead triple screw 2

45 Arc bevel pinion (7 teeth) 1

46 Lock knob

47 Chain cover

48 Adjusting platen

49 Saw chain

50 Tension pin 1

1

1

1

1

51 Adjusting screw

52 Guide plate seal ring

53 Guide bar

54 Axial snap ring

55 Sealing gasket

1

1

1

1

2

56 Axial snap ring

57 Sprocket platen

58 Adjusting bevel gear

59 Drive sprocket

60 Right Casing

61 Tightening knob

62 Adjusting link rod

63 Adjusting shaft platen

64 Umbrella-tooth platen

65 Inner plum pan head tapping screw

78

79

80

81

82

66 Seal ring

67 Oil tubing joint

68 Kettle rope

69 Spare kettle seal gasket

70

71

72

Oil filler cap

Oil kettle

Ventilation valve

73

74

75

76

77

Oil inlet pipe

Deep groove ball bearing

Output shaft

Semicircular key

Arc gearwheel (59 teeth)

Oil pump turbine

Deep groove ball bearing

DY155 oil pump

Oil outlet pipe

83

84

Left Casing

Battery pack

Charger

85 Chain cover

1

1

1

1

1

1

2

1

1

1

1

1

1

1

4

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

NOTE : Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

Page 16 WWW.LITHELI.COM

Item U1PS21000

Assembly Diagram

Item U1PS21000

WWW.LITHELI.COM

Page 17

Warranty

90-Day Money Back

You May Return Your Product for A Full Refund Within The First 90 Days of Your Purchase.

3-Year Battery and Charger Warranty

Against Defects in Workmanship and Materials.

Battery and Charger Must Be Used and Maintained in Accordance with The Manual of The

Operator's Instructions and Regulations.

5-Year Tool Warranty

Against Defects in Materials, Parts or Workmanship.

Litheli at Its Own Discretion Will Repair or Replace Any and All Parts Found To Be Defective.

All Units Must Be Used and Maintained in Accordance with The Directions and Regulations in The

Operator's Manual.

Returning The Product

Contact Us at www.litheli.com for The Return Address, We Will Issue Replace/Refund Upon Receiving

Your Return.

Need An Extra Copy of The Operator's Manual? Visit www.litheli.com to Download it.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement