Acer Veriton 5200, Veriton 5200D Service Manual

Document

Veriton 5200/5200D

Service Guide

Service guide files and updates are available on the AIPG/CSD web; for more information, please refer to http://csd.acer.com.tw

PART NO.: 49.37P01.601 & 49.31Q01.401

PRINTED IN TAIWAN

Revision History

Please refer to the table below for the updates made on Veriton 5200/5200D service guide.

11/19/2001

Date

Chapter 1

Chapter Updates

Add Veriton 5200D information

Copyright

Copyright © 2001 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

Disclaimer

The information in this guide is subject to change without notice.

Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.

Other brand and product names are trademarks and/or registered trademarks of their respective holders.

III

Conventions

The following conventions are used in this manual:

Screen messages

NOTE

WARNING

CAUTION

IMPORTANT

Denotes actual messages that appear on screen.

Gives bits and pieces of additional information related to the current topic.

Alerts you to any damage that might result from doing or not doing specific actions.

Gives precautionary measures to avoid possible hardware or software problems.

Reminds you to do specific actions relevant to the accomplishment of procedures.

Preface

Before using this information and the product it supports, please read the following general information.

This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.

Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service

Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

Table of Contents

Chapter 1 System Specifications 1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Front Panel-Veriron 5200/5200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Rear Panel-Veriton 5200/5200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

System Block Diagram (Veriton 5200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

System Block Diagram (Veriton 5200D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Main Board Layout (Veriton 5200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Main Board Layout (Veriton 5200D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Power Management Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

hapter 2 System Utilities 26

Entering Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Standard CMOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

IDE Primary Master/Slave and IDE Secondary Master/Slave Setup . . . . .31

Advanced BIOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Advanced Chipset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Integrated Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Power Management Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

PnP/PCI Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Frequency Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

System Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Supervisor Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

User Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Bypassing the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Load Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Exiting Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Advanced Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Advanced BIOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Advanced Chipset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Integrated Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Power Management Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

PC Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Frequency Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Chapter 3 Machine Disassembly and Replacement 56

Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Disassembling Veriton 5200/5200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Removing the Housing Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Removing a Link Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Removing a DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Removing the Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Removing the Hard Disk Drive and 3.5-inch Diskette Drive . . . . . . . . . . . .61

Removing the CD-ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Removing the PCI and AGP Expansion Cards . . . . . . . . . . . . . . . . . . . . . .64

Removing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

VII

Table of Contents

Chapter 4 Troubleshooting 66

Power-On Self-Test (POST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

POST Error Messages List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Error Symptoms List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Chapter 5 Jumper and Connector Information 80

Jumpers and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Connector Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Chapter 6 FRU (Field Replaceable Unit) List 84

Veriton 5200/5200D Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Appendix A Model Definition and Configuration 91

Veriton 5200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Veriton 5200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

Appendix B Test Compatible Components 94

Microsoft Windows XP Personal/ Professional (Beta) Test . . . . . . . . . . . . . . . .95

Microsoft Windows ME (EN/TW) Environment Test . . . . . . . . . . . . . . . . . . . . . .96

Microsoft Windows 2000 Professional Environment Test . . . . . . . . . . . . . . . . . .97

Microsoft NT 4.0 Workstation Environment Test (Driver Verify) . . . . . . . . . . . . .98

Microsoft Windows 98SE Environment Test (Driver Verify) . . . . . . . . . . . . . . . .99

Novell Netware 4.12 & 5.1 Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . .100

Linux Red Hat Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

Appendix

Online Support Information 102

Index 104

VIII

Table of Contents

Chapter 1 System Specifications

Overview

The Veriton 5200/5200D supports Intel

Pentium IV (Willamette 478/Northwood) Flip Chip-Pin Grid Array 2 processor (FC-PGA2) based Micro ATX, IBM PC/AT compatible system with PCI/AGP bus.

Chapter 1 1

Features

Performance

Intel Pentium® IV processor with Intel NetBurst™ micro-architecture and integrated 256KB/

512KB on-die L2 cache memory in Flip Chip 2 (FC)-mPGA 478 socket form factor, with supporting

CPU clock up to 2.4GHz+.

System Front Side bus speed:400 MHz.

Maximum of 1GB DRAM within 3 DIMM sockets up to 3GB (Veriton 5200).

Maximum of 1GB DDR RAM within 2 DIMM sockets up to 2GB (Veriton 5200D).

Integrated LAN Controller (82801BA+PLC82562ET).

3.5-inch and 5.25-inch floppy disk drives.

CD-ROM, DVD-ROM or CD-RW drive

1x/2x/4x AGP slot (1.5V only)

High capacity, Enhanced-IDE hard disk

Power management features

CPU SMM (System Management Mode), STOP clock control

On-board PCI master enhanced local bus IDE (Embedded in 82801BA chipset).

PIO mode 4

Multiword DMA Mode 2

Ultra DMA/33, Ultra DMA/66 & Ultra DMA/100 modes

Plug-and-Play (PnP) feature

ACPI 1.0 b Compliant Power management and Configuration Support

Software shutdown for Windows 95/98/ME/2000/XP

Hardware monitor function

On-board DC-DC converter(VRM 9.2 spec)

Multimedia

128-bit graphics accelerator installed in the AGP Pro card slot

Cathode-ray tube(CRT) support

Liquid crystal display (LCD) support(optional)

An additional AGP card 1.5V slot, supports 1X, 2X and 4X

3-D quality audio system via onboard audio controller

Audio-in/Line-in, Audio-out/Line-out/Headphone-out, Mic-in, and Game/MIDI interface

NOTE: The system has dual RJ-11 phone jacks for line and phone on Modem card (option). One microphone jack and one speaker jack on FPIO board.

Connectivity

One AGP and three PCI slots

USB and PS/2 compatible mouse and keyboard interfaces

Two high-speed NS 16C550-compatible serial ports

One multi-mode parallel port

Four USB ports ( available on front and rear panels) with Plug and Play function

High-speed 56K V9.0 fax/data/voice PCI modem (optional)

One RJ45 connector supports IEEE 802./802.3u 10Base-T/100Base-TX-compatible network with

Chapter 1

remote wake-up function

Expansion

3 PCI slots + 3 DIMM slots (Veriton 5200) or 2 DIMM slots (Veriton 5200D) + 1 AGP slot

Upgradeable memory and hard disk

Human-centric design and ergonomics

Mini-tower form factor

Separate computer stand and rubber stands for quick and easy positioning

Space-saver solution

Accessible I/O ports

Smooth and stylish design

Low emission and low radiation

Chapter 1 3

Front Panel-Veriron 5200/5200D

The computer’s front panel consists of the following:

Label Icon Color Description

CD-ROM/DVD-ROM tray

Stop/Eject Button

Skip/Forward Button

Hard disk drive activity light-emitting diode (LED)

LAN activity LED

Power LED

Power switch

CD-ROM/DVD-ROM LED

Volume Control Tuner

CD-ROM/DVD-ROM Headphone/Earphone port

5.25-inch drive bays

3.5-inch floppy disk drive

Floppy drive LED

Floppy drive eject button

Chapter 1

Label Icon Color Description

Speaker-out/Line-out port

16 Pink Microphone-in port (front)

17 Black USB ports

Chapter 1 5

Rear Panel-Veriton 5200/5200D

Label Icon

White

Color Description

Power Switch

Voltage Selector Switch (some)

Power cord socket

Network port

Burgundy Parallel/printer port

Gold Game/MIDI port

Green

CRT/LCD monitor port*

Power supply

PS/2 mouse port

Purple

Black

PS/2 keyboard port

USB ports

Chapter 1

Label

Icon Color

Teal or Turquoise Serial port

Description

Lime Audio-out/Line-out jack

Light blue Audio-in/Line-in jack

Pink Microphone-in port (rear)

17 Blue

Expansion slots

CRT/LCD monitor port

NOTE: *The CRT monitor port is automatically disabled when an add-on VGA card is installed into the system.

Connect the monitor to the VGA port instead.

Chapter 1 7

System Block Diagram (Veriton 5200)

133 MB/S

PCI CNTRL

Floppy Parallel

8 Chapter 1

System Block Diagram (Veriton 5200D)

133 MB/S

PCI CNTRL

Chapter 1 9

Main Board Layout (Veriton 5200)

10 Chapter 1

Main Board Layout (Veriton 5200D)

FN1

DIMM 2

DIMM 1

U12

CN10

JP1

CNM1

CN6

CN19

CN17

CN16

CNSW1

U21

JP14

CN21

CN20

JP3

AGP

PCI 3

PCI 2

PCI 1

U29

CN2

CN4

CN5

CN9

Chapter 1 11

AGP

BT1

CN2

Label

CN3

CN4

CN5

CN6

CN7

CN8

CN9

CN10

CN14

CN15

CN16

CN17

CN19

CN20

CN21

CN23

AGP slot

Battery

Component

CD-in connector

FDD connector

Intrusion connector

HDD LED connector

Power button

Front USB connector

Power/Suspend LED connector

EXT PCI slot

CNM1

Label

CNSW1

DIMM1

PS/2 mouse (upper) and keyboard

(lower) ports

Power connector

Network (upper) and USB (lower) ports

Parallel port (upper) and serial ports

(lower )

Memory Stick Connector

DIMM2

DIMM3

FN1

IDE 2 connector

IDE 1 connector

Game/MIDI (upper), line-out (left), linein (middle) and mic-in (right) connectors

Power connector (+12V)

FN2

FN3

PCI1

PCI2

PCI3

U12

U16

U21

U29

JP1

JP3

JP14

CNX1

Audio FPIO connector

NOTE: Shared connection with serial port 2,

NOTE: ** Default Settings

Component

Smart card connector (com2)*

IDE cold swap pin

Memory slot 1

Memory slot 2

Memory slot 3 (not for Veriton 5200D)

3-pin fan SYS connector

3-pin fan CPU connector

3-pin fan SYS connector

PCI slot 1

PCI slot 2

PCI slot 3

CPU socket

Intel 845 socket

SMSC chipset

Intel ICH2 chipset

BIOS chipset

LAN active LED connector

Model Select

1-2 Clear CMOS

2-3 Normal **

Chapter 1

Keyboard

The keyboard has full-sized keys that include separate cursor keys, two Windows keys and twelve function keys.

Icon

Chapter 1

Component

Programmable keys

Internet/Suspend keys

Description

Help you directly access a URL (Web site) or launch any program, file, or application in your system. The fifth key is set to launch the media player.

To configure the settings of each key, right-click on the Magic Keyboard icon located on your Windows desktop.

Consist of three buttons:

• dled with your system.

• Web browser : launches the browser application that came bundled with your system.

Multimedia keys

• Suspend/Resume : puts the system to sleep when pressed. To wake up the system press it again.

Allows you to do the following:

•

Play/Pause button : press to start playing the audio track or video file. Press again to pause.

Stop Button video file.

: press to stop playing the audio track or

• Forward Button or file and start playing.

: press to skip forward to the next track

• Backward button ous track or file and start playing.

Icon

Component

Volume control/Mute knob

Description

Controls the speaker volume. Turn it clockwise or counterclockwise to adjust the volume. Press it to toggle between mute and sound.

Scroll Lock

Num Lock

Cursor keys

Application key

When activated, the screen moves one line up or down when you press the up arrow or down arrow respectively. Take note that Scroll Lock may not work with some applications.

When activated, the keypad is set to numeric mode, i.e., the keys function as a calculator (complete with arithmetic operators such as +, -, * and /).

Also called arrow keys, let you move the cursor around the screen. They serve the same function as the arrow keys on the numeric pad when the

Num Lock is toggled off.

Opens the applications context menu (same function as clicking the right button of the mouse).

Windows logo key

Caps lock

Function keys

Start button. Combinations with this key perform special functions, such as:

•

• Windows + Tab

Windows + E

: Activates the next Taskbar button

: Explore My Computer

•

• Windows + F:

Windows + M

Windows + R

Find Document

: Minimize All

Shift + Windows + M : Undo Minimize All

: Displays Run dialog box

When activated, all alphabetic characters typed appear in uppercase

(same function as pressing SHIFT + <letter>).

Access most of the computer's controls like screen brightness, volume output and the BIOS utility.

Chapter 1

Hardware Specifications and Configurations

Processor

Item

Type

Speed

Minimum operating speed

Voltage

Specification

Intel® Pentium IV processors with mPGA478 package

Internal : 1.4~2.4GHz+

External: 400MHZ Data Bus Frequency

0 MHz (If Stop CPU Clock in Sleep State the BIOS Setup is set to Enabled .)

Processor voltage can be detected by the system without setting any jumper.

BIOS

Item Specification

BIOS code programmer

BIOS version

BIOS ROM type

BIOS ROM size

Support protocol

Boot from CD-ROM feature

Support to LS-120 drive

Award

V6.0

Intel FWH (e.g., SST49LF002A)

2MB

PCI 2.1, APM1.2, DMI 2.00.1, E-IDE, ACPI 1.0, ESCD 1.03, ANSI ATA 3.0, PnP

1a, Bootable CD-ROM 1.0, ATAPI

Yes

Support to BIOS boot block feature Yes

NOTE: The BIOS can be overwritten/upgraded using the FLASH utility (AWDFLASH.EXE).

BIOS Hotkey List b a +

Hotkey a o

+ ^

Function

Enter BIOS Setup Utility

Description

Press while the system is booting to enter BIOS

Setup Utility.

Enable hidden page of BIOS Setup Utility Press in BIOS Setup Utility main menu screen, the Advanced Options menu then appears.

The items on the Advanced Options menu are:

Memory/Cache Options

PnP/PCI Options

Chips Options

Chapter 1 15

This section has two table lists, system memory specification and the possible combinations of memory module.

System Memory (Veriton 5200)

Item

Memory socket number

Support memory size per socket

Support maximum memory size

Support memory type

Support memory speed

Support memory voltage

Support memory module package

Support to parity check feature

Support to Error Correction Code (ECC) feature.

Memory module combinations

3 sockets (3 banks)

64/128/256/512MB

3GB

SDRAM

133MHz(PC133)

3.3V

168 -pin DIMM

Yes

Specification

You can install memory modules in any combination as long as they match the Memory Combination specifications.

System Memory (Veriton 5200D)

Item

Memory socket number

Support memory size per socket

Support maximum memory size

Support memory type

Support memory speed

Support memory voltage

Support memory module package

Support to parity check feature

Support to Error Correction Code (ECC) feature.

Memory module combinations

2 sockets (2 banks)

128/256/512MB

2GB

DDR RAM

266MHZ

2.5V

184 -pin DIMM

Yes

Specification

You can install memory modules in any combination as long as they match the Memory Combination specifications.

Memory Combinations (Veriton 5200)

DIMM 1

64M

128M

256M

64M

128M

256M

64M

128M

256M

NOTE: * X, Y, Z: 0~1GB

64M

128M

256M

64M

128M

256M

DIMM 2

64M

128M

256M

DIMM 3

3GB

64M

128M

256M

128M

256M

512M

192M

384M

768M

TOTAL

Chapter 1

Memory Combinations (Veriton 5200D)

DIMM 1

128M

256M

512M

1024M

128M

256M

512M

1024M

DIMM 2

128M

256M

512M

1024M (1G)

2048M (2G)

TOTAL

Cache Memory

Item

First-Level Cache Configurations

Specification

Cache function control Enable/Disable by BIOS Setup (Advanced options)

Second-Level Cache Configurations: Below information is only applicable to system with installed Pentium 4 processor.

L2 Cache RAM size Pentium IV processor: 256 KB

L2 Cache RAM speed

L2 Cache function control

The same with the processor core clock frequency

Enable/Disable by BIOS Setup

Chapter 1 17

Video Interface

Item

Video controller resident bus

Video interface support

Specification

AGP bus

1x / 2x / 4x AGP Signaling and 2x / 4x Fast Writes

The AGP buffers operate only 1.5V mode

Audio Interface

Item

Audio controller

Audio controller resident bus

Audio function control

Mono or stereo

Specification

Embedded in Intel 82801BA ICH II

AC’97 link

Enable/disable by BIOS Setup

Stereo

Music synthesizer

Sampling rate

MPU-401 UART support

Microphone jack

Headphone jack

Package

IDE Interface

Item

IDE controller

IDE controller resident bus

Number of IDE channel

Support IDE interface

Support bootable CD-ROM

Sound Blaster Pro compatible

Mixed digital and analog high performance chip

Enhanced stereo full duplex operation

High performance PCI audio accelerator

Full native DOS games compatibility

High-Quality ESFM music synthesizer

MPU-401(UART mode) interface for wavetable synthesizers and MIDI devices

Integrated dual game port

Meets PC97/PC98 and WHQL specifications

Yes

44.1 KHz

Yes

Supported On audio-I/O board (connects via CN6)

QFP64

Specification

Embedded in Intel 82801BA ICH II

PCI bus

2 on-board: 40-pin hard disk drive connector,

E-IDE (up to PIO mode 4 and Ultra DMA/33, Ultra DMA/66 and Ultra DMA/100 mode 2) ANSIS ATA rev.4.0 ATAPI

Yes

Floppy disk drive Interface

Item

Floppy disk drive controller

Specification

Embedded in SMSC LPC 47M192

Floppy disk drive controller resident bus LPC

Support FDD format 360KB, 720KB, 1.2MB, 1.44MB, 2.88MB; 3-mode

Chapter 1

Parallel Port

Item

Parallel port controller

Parallel port controller resident bus

Number of parallel ports

Support ECP/EPP

Connector type

Parallel port function control

Optional ECP DMA channel

(in BIOS Setup)

Optional parallel port I/O address

(via BIOS Setup)

Optional parallel port IRQ

(via BIOS Setup)

Serial Port

Item

Serial port controller

Serial port controller resident bus

Number of serial port

Serial ports location

16550 UART support

Connector type

Optional serial port I/O address

(via BIOS Setup)

Optional serial port IRQ

(via BIOS Setup)

Modem

Item

Fax modem data baud rate (bps)

Data modem data baud rate (bps)

Voice modem

Modem connector type

Full duplex

USB Port

Universal HCI

USB Class

Items

Specification

Embedded in SMSC LPC 47M192

LPC

SPP/ECP / EPP 1.7 & 1.9

25-pin D-type female connector

Enable/disable by BIOS Setup

DMA channel 1

DMA channel 3

378h

278h

IRQ5

IRQ7

Specification

Embedded in SMSC LPC 47M192

LPC

COM1, COM 2

Yes

10-pin connector

3F8h, 2F8h, 3E8h, 2E8h

4, 3

14.4K bps

56K bps

Yes

Not Applicable

Not applicable

Specification

Specifications

USB 1.1

Support legacy keyboard for legacy mode

Chapter 1 19

Memory Address Map

Address

000000 - 07FFFF

080000 - 09FFFF

0A0000 - 0BFFFF

0C0000 - 0C7FFF

0C8000 - 0DFFFF

0E0000 - 0EFFFF

0F0000 - 0FFFFF

100000 - UPPER LIMIT

UPPER LIMIT - 4GBytes

512KBytes

Size

128KBytes

32KBytes

96KBytes

64KBytes

Function

Host Memory

Host/PCI Memory

PCI/ISA Video Buffer Memory

Video BIOS Memory

ISA Card BIOS & Buffer Memory

BIOS Extension Memory

Setup and Post Memory

PCI Development BIOS

System BIOS Memory

Main Memory

PCI Memory

Note : UPPER LIMIT means the maximum size of installed memory.

The Main Memory Maximum size is 768M Bytes.

Onboard Device ID & IRQ Map

Intel 845 MCH

P2P

Device

(Func.0) ICH2 (LPC)

(Func.1) ICH2 (IDE)

(Func.2) ICH2 (USB)

(Func.3) ICH2 (SMBUS)

(Func.5) ICH2 (AC97 Audio)

PCI Slot 1

PCI Slot 2

PCI Slot 3

AD11

AD30

AD31

AD16

AD17

AD21

AD#

00h

13h

14h

05h

06h

07h

IDSEL Route Reg.

68h

61h

60h

61h

62h

FFh

Mask

PCI Slot IRQ Routing Map

PCI INTX#

PCI 1

PCI 2

PCI 3

Route 1

Route 2

Route 3

INTA

Route 2

INTB

Route 3

Route 4

INTC

Route 3

Route 4

Route 1

Route 4

INTD

Route 1

Route 2

Chapter 1

I/O Address Map

Hex Range

170-177

1F0-1F7

278-27F

2F8-2FF

378-37F

3F0-3F5

3F6-3F6

3F7-3F7

3F8-3FF

0CF8

0CFC

778-77A

000-00F

020-021

040-043

060-060

061-061

070-071

081-08F

0A0-0A1

0C0-0DF

0F0-0FF

IRQ Assignment Map

IRQ7

IRQ8

IRQ9

IRQ10

IRQ11

IRQ12

IRQ13

IRQ14

IRQx

IRQ0 Timer

IRQ1

IRQ2

Keyboard

System Devices

Cascade Interrupt Control

IRQ3

IRQ4

IRQ5

IRQ6

Serial Alternate

Serial Primary

Parallel Port (Alternate)

Floppy Diskette

Parallel Port

Real Time Clock

PS/2 Mouse

Math Co-processor Exception

Fix Diskette

IRQ15 Fix Diskette

NOTE: N - Not to be used.

Devices

DMA Controller-1

Interrupt Controller-1

System Timer

Keyboard Controller 8742

System Speaker

CMOS RAM Address and Real Time Clock

DMA Controller-2

Interrupt Controller-2

DMA Controller-2

Math Co-Processor

Secondary IDE

Primary IDE

Parallel Printer Port 2

Serial Asynchronous Port 2

Parallel Printer Port 1

Floppy Disk Controller

Secondary IDE

Primary IDE

Serial Asynchronous Port 1

Configuration Address Register

Configuration Data Register

Parallel Printer Port 1

Reserved

Add-On-Card Devices

Chapter 1 21

DRQ Assignment Map

DRQx

DRQ0

DRQ1

DRQ2

DRQ3

DRQ4

DRQ5

DRQ6

DRQ7

NOTE: N - Not to be used.

System Devices

N (Notes)

Floppy Diskette

Cascade

Main Board Major Chips

Item

North Bridge

South Bridge

Super I/O controller

Audio controller

LAN controller

HDD controller

Keyboard controller

RTC

Intel 82845GMCH

Intel 82801BA ICH II

SMSC LPC47M192

Built-in Intel 82801 ICH II

Intel 82562ET

Built-in Intel 82801BA ICH II

Reserved

Add-On-Card Devices

Controller

Environmental Requirements

Temperature

Operating

Non-operating

Humidity

Operating

Non-operating

Vibration

Operating:

Item

+10 to +45 ° C

-10 to +60 ° C

-20 to +60 ° C (Storage package)

Specifications

20% to 80% RH, non-condensing

20% to 80% RH, non-condensing (Unpacked)

20% to 80% RH, non-condensing (Storage package)

5~16.2 Hz 0.38mm (peak to peak)

16.2~250 Hz 0.2G

Sweep rate:

Direction:

Test cycles:

Non-operating:

(Packed)

Sweep rate:

Direction:

Test cycles:

1 octave/minute

X, Y, Z axis

2 cycles per axis

5~27.1 Hz 0.6G

27.1~50 Hz 0.4mm (peak to peak)

50~500 Hz 2.0G

0.5 cotave/minute

X, Y, Z axis

4 cycles per axis

Chapter 1

Mechanical Specifications

Item

Weight

One 3.5 FDD and one 3.5 HDD

(without packing)

Depends on local configuration

Specification

Switching Power Supply 200W (165W option)

A-1 Inpute frequency

Normal Frequency

50Hz

60Hz

47Hz to 53Hz

57Hz to 63Hz

Frequency Variation Range

A-2 Input voltage

Nominal Voltage

100 - 120 VRMS

200 - 240 VRMS

90-132 VRMS

180-264 VRMS

Variation Range

A-3 Input current

Input Current Measuring Range

90 -132 VRMS

180 - 264 VRMS

(This is 200W or 235W power supply)

This :4A: includes the oultet supply current: 2A

Measure at line input 90 VRMS and maximum load condition

+5V

+12V

-12V

+3.3V

-5V

+5Vaux

Output Requirements

+-5%

+-10%

+-5%

+-10%

+-5%

Regulation

NOTE: 1. +5V & +3.3V total power is 80W max .

0.3A

10A

0.2A

Current Rating(Max)

Chapter 1 23

Power Management Functions

Device Standby Mode

Independent power management timer for hard disk drive devices

(0-15 minutes, time step=1 minute).

Hard disk drive goes into Standby mode (for ATA standard interface).

Disable V-sync to control the VESA DPMS monitor.

Resume method: device activated (Keyboard for DOS, keyboard & mouse for Windows).

Resume recovery time: 3-5 sec.

Global Standby Mode

Global power management timer (2-120 minutes, time step=10 minute).

Hard disk drive goes into Standby mode (for ATA standard interface).

Disable H-sync and V-sync signals to control the VESA DPMS monitor.

Resume recovery time: 7-10 sec.

Suspend Mode

Independent power management timer (2-120 minutes, time step=10 minutes) or pushing external switch button

CPU goes into SMM.

CPU asserts STPCLK# and goes into the Stop Grant State.

LED on the panel turns amber color.

Hard disk drive goes into SLEEP mode (for ATA standard interface).

Disable H-sync and V-sync signals to control the VESA DPMS monitor.

Return to original state by pushing external switch button.

Suspend to RAM

The system context is maintained in system memory

Power is shut to non-critical circuits.

Memory is retained, and refreshes continually.

All clocks shut except RTC.

Return to original state by pushing external switch button & “PME” events at ACPI mode.

24 Chapter 1

Chapter 1 25

Chapter 2 System Utilities

Most systems are already configured by the manufacturer or the dealer. There is no need to run

Setup when starting the computer unless you get a Run Setup message.

The Setup program loads configuration values into the battery-backed nonvolatile memory called CMOS RAM.

This memory area is not part of the system RAM.

NOTE: If you repeatedly receive Run Setup messages, the battery may be bad. In this case, the system cannot retain configuration values in CMOS.

Before you run Setup, make sure that you have saved all open files. The system reboots immediately after you exit Setup.

Chapter 2 26

Entering Setup

To enter Setup, press the key combination b + a + | during the POST (Power-on self-test).

NOTE: You must press b + a + | simultaneously while the system is booting.

The Setup Utility main menu then appears:

The above screen is the BIOS Utility Basic Level screen. It allows you to view and change only the basic configuration of your system.

The command line at the bottom of the menu tells you how to move within a screen and from one screen to another.

To select an option, move the highlight bar by pressing w , y , z , or x keys then press e .

To change a parameter setting, press { or } until the desired setting is found, or press e to pop out the screen with available items for selection.

Press ^ to return to the main menu. If you are already in the main menu, press ^ again to exit Setup.

The parameters on the screens show default values. These values may not be the same as those in your system.

The grayed items on the screens have fixed settings and are not user-configurable.

27 Chapter 2

Product Information

The screen below appears if you select Product Information from the main menu:

The Product Information menu contains general data about the system, such as the product name, serial number, BIOS version, etc. These information is necessary for troubleshooting (maybe required when asking for technical support).

The following table describes the parameters found in this menu:

Parameter

Product Name

System S/N

Main Board ID

Main Board S/N

System BIOS Version

SMBIOS version

Description

Displays the model name of your system.

Displays your system’s serial number.

Displays the main board’s identification number.

Displays your main board’s serial number.

Specifies the main version of your BIOS utility.

The System Management Interface (SM) BIOS allows you to check your system hardware components without actually opening your system. Hardware checking is done via software during start up. This parameter specifies the version of the

SMBIOS utility installed in your system.

Chapter 2 28

Standard CMOS Features

Select “Standard CMOS Features” from the main menu to configure the drives installed in your system.

The following screen shows the Disk Drives menu:

The following table describes the parameters found in this menu.

Parameter

Date

Time

IDE Primary Master

IDE Primary Slave

IDE Secondary Master

IDE Secondary Slave

Drive A

Description

Lets you set the date following the weekday-month-dayyear format

Lets you set the time following the hour-minute-second format

Options

Weekday : Sun, Mon....Sat

Month : Jan, Feb...Dec

Day : 1 to 31

Year: 1980 to 2079

Hour: 0 to 23

Minute : 0 to 59

Second : 0 to 59

IDE Device Model Number

None

Lets you configure the hard disk drive connected to the master port of IDE channel 1.

To enter the IDE Primary Master setup, press Enter .

The IDE CD-ROM is always automatically detected.

Lets you configure the hard disk drive connected to the slave port of IDE channel 1.

To enter the IDE Primary Slave setup, press Enter .

The IDE CD-ROM is always automatically detected.

Lets you configure the hard disk drive connected to the master port of IDE channel 2.

To enter the IDE Secondary Master setup, press Enter .

The IDE CD-ROM is always automatically detected.

Lets you configure the hard disk drive connected to the slave port of IDE channel 2.

To enter the IDE Secondary Slave setup, press Enter .

The IDE CD-ROM is always automatically detected.

Allows you to configure your floppy drive A.

IDE Device Model Number

None

IDE Device Model Number

None

IDE Device Model Number

None

1.44 MB, 3.5-inch

None

360 KB, 5.25-inch

1.2 MB, 5.25-inch

720 KB, 3.5-inch

2.88 MB, 3.5-inch

Chapter 2

Drive B

Parameter

Video

Halt On

Base Memory

Extended Memory

Total Memory

Description

Allows you to configure your floppy drive B.

This item specifies the type of video card in use. The default setting is VGA/EGA. Since current PCs use

VGA only, this function is almost useless and may be disregarded in the future.

This parameter enables you to control the system stops in case of Power-on self-test (POST) errors.

Options

None

360 KB, 5.25-inch

1.2 MB, 5.25-inch

720 KB, 3.5-inch

1.44 MB, 3.5-inch

2.88 MB, 3.5-inch

EGA/VGA

CGA40

CGA80

Mono

All Errors

No Errors

All, But Keyboard

All, But Diskette

All, But Disk/Key

Refers to the portion of memory that is available to standard DOS programs. DOS systems have an address space of 1 MB, but the top 384 KB (called high memory) is reserved for system use. This leaves 640

KB of conventional memory. Everything above 1 MB is either extended or expanded memory.

Memory above and beyond the standard 1 MB

(megabyte) of base memory that DOS supports.

Extended memory is only available in PCs with an Intel

80286 or later microprocessor. Extended memory is not configured in any special manner and is therefore unavailable to most DOS programs. However, MS

Windows and OS/2 can use extended memory.

Total base, and extended memory, and I/O ROM 384KB available to the system.

Chapter 2 30

IDE Primary Master/Slave and IDE Secondary Master/Slave Setup

The following screen appears if you select any of the IDE drive parameters:

The following table describes the parameters found in this menu.

Parameter

IDE HDD Auto-

Detection

IDE Primary Master

Access Mode

Capacity

Cylinder

Head

Precomp

Landing Zone

Sector

Description

Auto-detects your hard disk drive.

Press Enter

Options

Displays the device type

Selects the HDD access mode

Shows the size of your hard disk in MB.

Shows your hard disk’s number of cylinders.

Shows your hard disk’s number of heads

Selects the Precomp number for old HDD parking

Selects the Landing Zone number for old HDD parking

Shows your hard disk’s number of sectors

Auto

None

Manual

Auto

Large

LBA

CHS xxxxx MB

0 to 65535

0 to 255

0 to 65535

0 to 255

31 Chapter 2

Advanced BIOS Features

The following screen shows the Advanced BIOS Features.

The following table describes each Advanced BIOS Features parameter. Settings in boldface are the default and suggested settings.

Parameter

Virus Warning

Quick Power On Self Test

Silent Boot

Configuration Table

Hard Disk Boot Priority

First Boot Device

Second Boot Device

Third Boot Device

Boot Other Device

Description

Allows you to choose the Virus warning feature for the IDE hard disk boot sector protection. If this function is enabled and someone attempts to write data into this area, BIOS will show a warning message on screen and alarm beep.

This parameter speeds up POST by skipping some items that are normally checked.

Disabled

Enabled

This item is used to decide if the system logo displays when the system boots up.

Displays preboot system configuration table when enabled.

Select Hard Disk Boot Device Priority

This parameter allows you to specify the system boot up search sequence.

Options

Enabled

Disabled

Enabled

Disabled

Disabled

Enabled

Press Enter

Show Hard Disk Model

CD-ROM, Floppy, LS120, Hard

Disk, ZIP100, LAN (on board

LAN-- Boot from LAN),

Disabled

Floppy , LS120, Hard Disk,

CD-ROM, ZIP100, LAN (on board LAN-- Boot from LAN),

Disabled

Hard Disk, Floppy, LS120,

CD-ROM, ZIP100, LAN (on board LAN-- Boot from LAN),

Disabled

Enabled

Disabled

Chapter 2 32

Parameter

Security Option

Description

The Setup option limits access only to BIOS setup.

To disable the security option, select Password

Setting from the main menu, don’t type anything and just press Enter .

The System option limits access to both the

System boot and BIOS setup. A prompt asking you to enter your password appears on the screen every time you boot the system.

Setup

System

Options

33 Chapter 2

Advanced Chipset Features

The following screen shows the Advanced Chipset Features.

The following table describes each Advanced Chipset Features parameter. Settings in boldface are the default and suggested settings..

Parameter

Memory Hole at 15M-16M

AGP Aperture Size (MB)

Description

This option lets you reserve system memory area for special ISA cards. The chipset accesses code/ data of these areas from the ISA bus directly.

Normally, these areas are reserved for memory mapped I/O cards.

This item lets you determine the effective size of the

AGP Graphic Aperture.

Disabled

Enabled

Options

64 , 4, 8, 16, 32, 128 and 256

Chapter 2 34

Integrated Peripherals

The following table describes each Integrated Peripherals parameter. Settings in boldface are the default and suggested settings.

Parameter

On-Chip Primary PCI IDE

On-Chip Secondary PCI IDE

IDE Primary Master PIO

IDE Primary Slave PIO

IDE Secondary Master PIO

IDE Secondary Slave PIO

IDE Primary Master UDMA

IDE Primary Slave UDMA

IDE Secondary Master UDMA

IDE Secondary Slave UDMA

USB controller

Description

These parameters let you enable or disable the IDE devices connected to the primary and secondary IDE connectors.

Setting these items to Auto activates the HDD speed auto-detect function. The PIO mode specifies the data transfer rate of the HDD. For example, mode 0 data transfer rate is 3.3 MB/s, mode 1 is 5.2 MB/s, mode 2 is

8.3 MB/s, mode 3 is 11.1 MB/s and mode 4 is 16.6 MB/s.

If your hard disk performance becomes unstable, you may manually try the slower mode.

Caution: It is recommended that you connect the first

IDE device of each channel to the endmost connector of the IDE cable.

These items allow you to set the Ultra DMA/33/66/100 mode supported by the hard disk drive connected to your primary and secondary IDE connectors.

Enabled

Disabled

Options

Auto

Mode 1

Mode 2

Mode 3

Mode 4

Auto

Disabled

This item is used to enable or disable the On-chip USB.

Enabled

Disabled

Chapter 2

Parameter

USB Keyboard Support

USB Mouse Support

Init Display First

AC97 Audio

IDE HDD Block Mode

Onboard FDC Controller

Onboard Serial Port 1

Onboard Serial Port 2

Onboard Parallel Port

Parallel Port Mode

ECP Mode Use DMA

Game Port Address

Description

This item lets you enable or disable the USB keyboard driver within the onboard BIOS. The keyboard driver simulates legacy keyboard command and lets you use a

USB keyboard during POST or after boot if you don’t have a USB driver in the operating system.

This item lets you enable or disable the USB mouse driver within the onboard BIOS. The mouse driver simulates legacy mouse command and lets you use a

USB mouse during POST or after boot if you don’t have a USB driver in the operating system.

If you installed a PCI VGA card and an AGP card at the same time, this item lets you decide which one is the initial display card.

Enabling the on-die AC97 Audio if no add-on PCI Audio device.

Enabled

Disabled

Options

Enabled

Disabled

AGP

PCI

Auto

Disabled

This feature enhances disk performance by allowing multisector data transfers and eliminates the interrupt handling time for each sector. Most IDE drives, except with old designs, can support this feature.

Setting this parameter to Enabled allows you to connect your floppy disk drives to the onboard floppy disk connector instead of a separate controller card. Change the setting to Disabled if you want to use a separate controller card.

This item allows you to assign an address and interrupt for the board serial port.

Enabled

Disabled

Enabled

Disabled

This item allows you to assign an address and interrupt for the board serial port.

This item controls the onboard parallel port address and interrupt.

NOTE: If you are using an I/O card with a parallel port, make sure that the addresses and IRQs do not conflict.

378/ IRQ7

3BC/ IRQ7

278/ IRQ7

Disabled

IBM PC/AT and PS/2 compatible bi-directional parallel port.

Enhanced Parallel Port (EPP)-compatible with EPP1.7 and EPP 1.9.

Extended Capabilities Port (ECP) Specification by

Microsoft and HP.

IEEE 1284 compliant

2F8/ IRQ3

Auto

3F8/ IRQ4

3E8/ IRQ4

2E8/ IRQ3

Disabled

Printer

Show

SPP

PP1.9+ECP

Printer

EPP1.7+SPP

EPP!.7+ECP

Selects the ECP Mode DMA Channel.

3F8/ IRQ4

Auto

2F8/ IRQ3

3E8/ IRQ4

2E8/ IRQ3

Disabled

Selects the Game Port Address.

201

209

Disabled

Chapter 2 36

Parameter

Midi Port Address

Midi Port IRQ

Description

Selects the Midi Port Address.

Selects the Midi Port IRQ.

330

300

Disabled

Options

37 Chapter 2

Power Management Setup

The Power Management menu lets you configure the system power-management feature. It works only in

APM mode.

IMPORTANT: If an ACPI-aware operating system such as Windows 98 or Windows 2000 is installed in ACPI mode, the operating system will use the ACPI interfaces. Then the settings in Power Management page is non-effective.

The following screen shows the Power Management parameters and their default settings:

Chapter 2 38

The following table describes the parameters found in this menu .

Parameter

Power Management

(Function Enabled in APM Mode)

Suspend Mode

(Function Enabled in APM Mode)

HDD Power Down

(Function Enabled in APM Mode)

Soft-Off by PWR-BTTN

(Function Enabled in ACPI and

APM Mode)

Description

This function allows you to set the default parameters for power-saving modes. Set it to

Disable to turn off the power management function. Set it to User Define to choose your own parameters. See the Power Management

Mode Table.

This item lets you set the period of time after which the system enters into Suspend mode.

The Suspend mode can be Power On

Suspend or Suspend to Hard Drive, and it is selected in the “Suspend Mode Option”.

This option lets you specify the IDE HDD idle time before the device enters the power down state. This item is independent from the power states previously described in this section

(Standby and Suspend).

This is a specification of ACPI and supported by hardware. When Delay 4 sec. is selected, the soft power switch on the front panel can be used to control power On, Suspend and Off. If the switch is pressed less than 4 sec. during power On, the system will go into Suspend mode. If the switch is pressed longer than 4 sec, the system will be turned Off. The other setting is Instant-Off, where the soft power switch is only used to control On and Off, there is no need to press 4 sec, and there is no

Suspend.

Use PCI PME# Wake-Up system . PCI must meet PCI 2.2 specification.

User Define

Max Saving

Min Saving

Disabled

Options

Disabled , 1 min., 2 min., 4 min.,

8 min., 12 min., 20 min., 30 min.,

40 min., and 1 Hour

Disabled

1 min

15 min

Delay 4 sec .

Instant-Off

Disabled

Enabled

Wake-Up by PCI Card

(Function Enabled in ACPI and

APM Mode)

Power-On by Ring

(Function Enabled in ACPI and

APM Mode)

USB KB Wake-up from S3

(Function Enabled in ACPI mode)

When Enabled, any fax/ modem activity wakes up the system from suspend mode.

Disabled

Enabled

PWRON After PWR-Fail

(Function Enabled in ACPI and

APM Mode)

Resume by Alarm

(Function Enabled in ACPI and

APM Mode)

When enabled, any USB keyboard activity wakes up the system from S3 (STR, Suspend to RAM) mode.

Enabled

Disabled

Use this option to determine the manner by which the system will power on after a power failure.

Former Sts (former status) - System would return to its former running state prior to the power failure.

On - System would be on full on state upon resuming from power failure.

Former-Sts

Off

Off - System would remain off.

Use this option to set the date and time for your computer to boot up.

Date (of month) Alarm * - Indicate month when system will boot up. Set it to 0 if you want to boot everyday.

Time (hh:mm:ss) Alarm * - Indicate the hour, minute and second when system will boot up.

Disabled

Enabled

* Set Resume by Alarm to

Enabled, then press e

to show the range of Date and Time

Alarm.

NOTE: In ACPI mode: Valid-S5 and S4. In APM mode: Valid- shutdown

Chapter 2

Power Management Mode Table

Mode

Max Saving

Min Saving

1 hour

1 min

Doze Standby

1 hour

1 min

1 hour

1 min

Suspend HDD Power Down

15 min

1 min

Chapter 2 40

PnP/PCI Configurations

The table below describes each PnP/PCI configuration parameter. Settings in boldface are the default and suggested settings.

Parameter

Reset Configuration Data

Resources Controlled By

IRQ Resources

IRQ 3 (COM2)

IRQ 4 (COM1)

IRQ 5 (Network/Sound or

Others)

IRQ 7 (Printer or Others)

IRQ 9 (Video or Others)

IRQ 10 (SCSI or Others)

IRQ 11 (SCSI or Others)

IRQ 12 (PS/2 Mouse)

IRQ 14 (IDE1)

IRQ15 (IDE2)

Description

Select Enabled to reset Extended System

Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system configuration has caused such a serious conflict that the OS cannot boot.

Setting this option to Manual allows you to individually assign the IRQs and DMAs to the

ISA and PCI devices. Set this to Auto to enable the auto-configuration function.

If your ISA card is not PnP compatible and requires a special IRQ to support its function, set the selected IRQ to Legacy ISA. This setting informs the PnP BIOS to reserve the selected

IRQ for the installed legacy ISA card. The default is PCI/ISA PnP. Take note that PCI cards are always PnP compatible (except old PCI IDE cards).

Disabled

Enabled

Options

Auto (ESCD)

Manual

PCI/ISA PnP

Legacy ISA

Chapter 2

Parameter

PCI/VGA Palette Snoop

Description

This parameter permits you to use the palette snooping feature if you installed more than one

VGA card in the system. The PVI/VGA palette snoop function allows the control palette register

(CPR) to manage and update the VGA RAMDAC

(Digital Analog Converter, a color data storage) of each VGA card installed in the system. The snooping process lets the CPR send a signal to all the VGA cards so that they can update their individual RAMDACs. The signal goes through the cards continuously until all RAMDAC data has been updated. This allows the display of multiple images on the screen.

NOTE: Some VGA cards have required settings for this feature. Check your VGA card manual before setting this parameter.

Disabled

Enabled

Options

Chapter 2 42

Frequency Control

The following table describes the parameters found in this menu.

Parameter

Processor

Processor Speed

Description

Indicates the type of processor installed in your computer.

Indicates the processor speed.

43 Chapter 2

System Security

The Setup program has a number of security features to prevent unauthorized access to the system and its data.

Supervisor Password

To set a password:

At the prompt, type your password. Your password can be up to 8 alphanumeric characters. When you type the characters, they appear as asterisks on the password screen box.

After typing the password, press e

.

At the next prompt, re-type your password and press e again to confirm the new password. After the password entry, the screen automatically reverts to the main screen.

To disable the password, press e when prompted to enter the password. The screen displays a message confirming that the password has been disabled.

Chapter 2 44

User Password

To set a password:

At the prompt, type your password. Your password can be up to 8 alphanumeric characters. When you type the characters, they appear as asterisks on the password screen box.

After typing the password, press e .

At the next prompt, re-type your password and press Enter again to confirm the new password. After the password entry, the screen automatically reverts to the main screen.

To disable the password, press e when prompted to enter the password. The screen displays a message confirming that the password has been disabled.

45 Chapter 2

Bypassing the Password

If you forgot your password, you can bypass the password security feature thru hardware configuration.

RTC Battery

Follow these steps to bypass the password:

Turn off and unplug the system.

Open the system housing. Take off battery and short it.

Place on RTC battery, reboot the system and enter setup menu, to load default setting.

Clear CMOS

Follow these steps to bypass the password:

Reset CMOS, by adjusting JP7 to 1-2

Reboot the system.

Adjust the JP7 back to 2-3

NOTE: Please refer to the following

JP3: Model Select

1-2

2-3

JP3

Veriton

Extensa

Model Select

JP7: Clear CMOS

1-2

2-2

JP7 CMOS Check

Clear CMOS

Normal

Chapter 2 46

Load Default Settings

You need to reload the BIOS default settings every time you make changes to your system hardware configuration (such as memory size, CPU type, hard disk type, etc.); otherwise, BIOS will keep the previous

CMOS settings. Selecting this option displays the following dialog box:

Choosing Yes enables BIOS to automatically detect the hardware changes that you have made in your system. This option also allows you to restore the default settings.

Choosing No returns you to the main menu without loading the default settings.

47 Chapter 2

Exiting Setup

To exit the BIOS utility, simply press ^ . The following dialog box appears:

Select Yes to exit Setup. Select No to return to the main menu.

If you have made changes in the parameter settings, you will be asked if you want to keep the changes made to the BIOS. Select Yes to save your changes before you exit Setup. Select No to discard all changes and exit Setup.

Chapter 2 48

Advanced Options

NOTE: The Advanced Options menu is available only when you press a

+ o in the main menu.

The “Advanced Options” menu allows you to configure the system memory and PCI device settings.

The following screen shows the Advanced Options parameter:

CAUTION: Do not change any settings in the Advanced Options menu if you are not a qualified technician to avoid damaging the system.

Product Information

Selecting “Product Information” from the Advanced Options menu displays the following secreen:

This menu lets you configure the system memory.

The following table describes the parameters found in this sub-menu

Parameter

System BIOS ID

BIOS release date

Description

R01-C0. BIOS real version

BIOS release date

Chapter 2

Advanced BIOS Features

Selecting “Advanced BIOS Features” from the Advanced Options menu displays the following screen:

The following table describes the parameters found in the sub- menu. Settings in boldface are the default and suggested settings .

Parameter

CPU L1 & L2 Cache

Swap Floppy Drive

Boot Up Flopppy Seek

Boot Up NumLock Status

Gate 20 Option

Description

CPU L1 & L2 cache enabled

If the system has two floopy drives, choose enabled to assign physical drive B to logical drive A and vice versa.

If the item is enabled, BIOS will test floppy drives to determine whether they have 40 or 80 tracks.

Selects power on state for NumLock.

Fast: Lets chipset control Gate A20

Normal: A pin in the keyboard controller, controls Gate 20.

Default is fast.

Options

Enabled / Disabled

Disabled/ Enabled

On / Off

Fast /Normal

Chapter 2 50

Parameter

Typematic Rate Setting

Description

Keystrokes repeat at a rate determined by the keyboard controller-- when enabled, the typematic rate and typematic delay can be selected.

* Typematic Rate (Chars/Sec) 6

* Typematic Delay (MSec) 250

APIC Mode Advanced Interrupt Controller. The I/O APIC handles interrupts very differently than the 8259. (Refer to ICH2

EDS Rev 1.0 P6-39, 6.8)

MPS Version Control For OS Multi CPU for NT. system

Options

Disabled/ Enabled

Enabled

Disabled

1.4

/ 1.1

Advanced Chipset Features

Selecting “Advanced BIOS Features” from the Advanced Options menu displays the following screen.

The following table describes the parameters found in the sub-menu. Settings in boldface are the default and suggested settings.

Parameter

DRAM Timing Selectable

CAS Latency Time

Active to Precharge Delay

DRAM RAS #to CAS# Delay

DRAM RAS# Precharge

DRAM Data Integrity Mode

System BIOS Cacheable

Video BIOS Cacheable

Video RAM Cacheable

Delayed Transaction

Delay Prior to Thermal

Description

SDRAM Timing

The default setting by your DRAM’s SPD.

E.F segment shadow RAM cacheable.

C segment shadow RAM cacheable.

A.B segment shadow RAM cacheable.

ICH2 enables delayed transactions for internal register, FWH, and LPC I/F accesses.

Enables Pentium 4 thermal function - 16 miuntes after POST.(only for ACPI OS)

Option

1.5

/2/2.5/3

7 /6/5

3 /2

Non-ECC /ECCl

Enabled /Disabled

16/ 4/8/32 minutes

Chapter 2

Integrated Peripherals

The following table describes the parameters found in the sub-menu. Settings in boldface are the default and suggested settings.

Parameter

AC97 Modem

UART Mode Select

UR2 Duplex Mode

TxD, RxD Polarity Active

Description

Enabling the on-die AC97 MODEM if no add-on PCI

MODEM device.

Selects the UART as Serial Port (Normal) or IRDA or

ASKIR.

Selects the speed of UR2 Duplex Mode.

Selects the speed of TxD, RxD Polarity Active.

Use IR Pins Use IR Pins as IR-Rx2Tx2 or RxD2, TxD2

Option

Auto

Disabled

Normal

IrDA

ASKIR

Half

Full

Lo, Hi

Lo, Lo

Hi, Lo

Hi, Hi

IR-Rx2Tx2

RxD2, TxD2

Chapter 2 52

Power Management Setup

Selecting “Power Management Setup” from the Advanced Options menu displays the following screen:

The following table describes the parameters found in the sub-menu. Settings in boldface are the default and suggested settings.

Parameter

ACPI Functiont

ACPI Suspend Type

Video Off Method

Video Off In Suspend

Suspend Type

MODEM Use IRQ

Primary IDE 0*

Primary IDE 1*

Secondary IDE 0*

Secondary IDE 1*

FDD, COM, LPT port*

PCI PIRQ [A-D]#*

Description

ACPI power management

Selects the ACPI Suspend Type as S3 (STR, Suspend to

RAM) or S1 (POS, Power On Suspend)

Turn off the video by DPMS or Blank Screen or V/H SYNC

+ Blank Screen

Turn off the video when entering the Suspend mode.

When entering the Suspend mode, Stop Grant won’t stop

CPU Clock, PwrOn (Power On) Suspend will.

This item lets you set an IRQ for the modem.

To enable or disable the detection of Primary IDE 0 (HDD) activities for power down state transition.

To enable or disable the detection of Primary IDE 1 (HDD) activities for power down state transition.

To enable or disable the detection of Secondary IDE 0

(HDD) activities for power down state transition.

To enable or disable the detection of Secondary IDE 1

(HDD) activities for power down state transition.

To enable or disable the detection of FDD, COM port, and

LPT port activities for power down state transition.

To enable or disable the detection of PCI PIRQ [A-D]# activities for power down state transition.

Option

Enabled

Disabled

S3 (STR)

S1 (POS)

SYNC+BLANK

Blank Screen

V/H

Yes

Stop Grant

PwrOn Suspend

3 , 4, 5, 7, 9, 10, 11, and N/A

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

NOTE: These are global timer events.

Chapter 2

PC Health Status

Selecting “ PC Health Status” from the Advanced Options menu displays the following screen:

The following table describes the parameters found in the sub-menu.

Parameter

Shutdown Temperature

Dexcription

CPU Temperature

Ambient Temperature

VCore (from VID)

(Physical) VCore

+3.3V

+5V

+12V

Standby 3.3V

+1.5V

+1.8V

Current CPU FAN1 Speed

Current CPU FAN2 Speed

Option

The option items vary depending on your BIOS.

Chapter 2 54

Frequency Control

Selecting “ Frequency Control” from the Advanced Options menu displays the following screen:

The following table describes the parameters found in the sub-menu.

Parameter

CPU Clock Ratio

Auto Detect PCI C1K

Spread Spectrum

CPU Host/PCI Clock

Description

Core Clock Frequency to System Bus Ratio (RO)

This parameter let you enable or disable the spread spectrum.

Front side bus frequency/PCI clock.

Option

The option items vary depending on your BIOS.

Enabled /Disabled

+/-0.25%

Disabled

-0.5%

+/-0.5%

+/-0.38

Default

100/33 Mhz

105/35 Mhz

108/36 Mhz

114/38Mhz

120/40Mhz

55 Chapter 2

Chapter 3 Machine Disassembly and Replacement

This chapter contains 2 separate step-by-step procedures on how to disassemble the Veriton 5200/5200D desktop computer for maintenance and troubleshooting.

To disassemble the computer, you need the following tools:

Wrist grounding strap and conductive mat for preventing electrostatic discharge

Flat-bladed screwdriver

Phillips screwdriver

Hexagonal screwdriver

Plastic stick

NOTE: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatches when putting back the components.

Chapter 3 56

Disassembly Procedure Flowchart

The flowchart on the succeeding page gives you a graphical representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing.

Housing Cover

Memory Link Bar

HDD

FDD

CPU

PCI and AGP

Expansion Cards

CD-ROM Power Supply

57 Chapter 3

Disassembling Veriton 5200/5200D

Removing the Housing Cover

CAUTION: Before you proceed, make sure that you have turned off the system and all peripherals connected to it.

Turn off the system power and unplug all cables.

Place the system unit on a flat, steady surface.

Turn the thumbscrews counterclockwise to remove the cover. Set the screws aside. You will need them when replacing the housing cover.

Hold the sides of the cover with both hands. Slide it back about an inch and then gently pull it outward to detach it.

Chapter 3 58

Removing a Link Bar

See “Removing the Housing Cover” on page 58

To remove a link bar, remove the screw that secures it to the housing.

Then gently lift the link bar and pull it out.

Removing a DIMM

See “Removing the Housing Cover” on page 58

Press the latches on both sides of the DIMM socket outward, to release the DIMM.

Then gently lift the DIMM out to remove it.

59 Chapter 3

Removing the Processor

Follow these steps to remove the processor:

See “Removing the Housing Cover” on page 58

Detach the fan/heatsink cable connector .

Remove the fan/heatsink from the processor.

Pull the socket lever up to release the processor pins from the socket holes.

Pull out the processor from the socket.

WARNING:The heatsink becomes very hot when the system is On. Never touch the heatsink with any metal or with your hands.

Chapter 3 60

Removing the Hard Disk Drive and 3.5-inch Diskette Drive

Follow these steps to remove the hard disk drive:

See “Removing the Housing Cover” on page 58

See “Removing a Link Bar” on page 59

Detach the power and disk drive cables from the hard disk and diskette drive.

Remove the screw that secures the link bar to the housing.

Lift up the link bar and pull it out.

61 Chapter 3

Remove the four screws that hold the hard disk drive to the disk frame and detach the hard disk drive. Set the screws aside.

Remove the four screws that hold the diskette drive to the disk frame and pull out the diskette drive.

Chapter 3 62

Removing the CD-ROM Drive

See “Removing the Housing Cover” on page 58.

See “Removing a Link Bar” on page 59

Remove the four screws that hold the CD-ROM drive to the bracket frame and pull out the CD-ROM drive.

63 Chapter 3

Removing the PCI and AGP Expansion Cards

See “Removing the Housing Cover” on page 58

Remove the screw on the bracket of an expansion card. Set the screw aside. You will need it when replacing the expansion card.

Gently pull out the expansion card to remove it from the expansion slot.

Chapter 3 64

NOTE: When you turn on the system, BIOS automatically detects and assigns resources to the PCI devices.

Removing the Power Supply

See “Removing the Housing Cover” on page 58

See “Removing a Link Bar” on page 59

Remove the four screws that hold the power supply to the housing and pull out the power supply.

65 Chapter 3

Troubleshooting

This chapter provides troubleshooting information for the Veriton 5200/5200D:

Power-On Self-Test (POST

Index of Error Message

Index of Error Symptoms

Undetermined Problems

Chapter 4

Chapter 4 66

Power-On Self-Test (POST)

Each time you turn on the system, the Power-on Self Test (POST) is initiated. Several items are tested during

POST, but is for the most part transparent to the user.

The Power-On Self Test (POST) is a BIOS procedure that boots the system, initializes and diagnoses the system components, and controls the operation of the power-on password option. If POST discovers errors in system operations at power-on, it displays error messages on screen, generates a check point code at port

80h or even halts the system if the error is fatal.

The main components on the main board that must be diagnosed and/or initialized by POST to ensure system functionality are as follows:

Microprocessor with built-in numeric co-processor and cache memory subsystem

Direct Memory Access (DMA) controller (8237 module)

Interrupt system (8259 module) or APIC (advance program interrupt controller)

Three programmable timers (system timer and 8254 module)

ROM subsystem

RAM subsystem

CMOS RAM subsystem and real time clock/calendar with battery backup

Onboard serial interface controller

Onboard parallel interface controller

Embedded hard disk interface and one diskette drive interface

Keyboard and auxiliary device controllers

I/O ports

Two RS232 serial ports

One parallel port

One PS/2-compatible mouse port

OnePS/2-compatible keyboard port

NOTE: When Post executes a task, it uses a series of preset numbers called check points to be latched at

port 80h, indicating the stages it is currently running. This latch can be read and shown on a debug board.

The following table describes the BIOS common tasks carried out by POST. Each task is denoted by an unique check point number. For other unique check point numbers that are not listed in the table, refer to the corresponding product service guide.

Post Checkpoints List: The list may vary accordingly depending on your BIOS

Checkpoint

CFh

C0h

C1h

C3h

C5h

0h1

02h

Description

Test CMOS R/W functionality

Early chipset initialization:

-Disable shadow RAM

-Disable L2 cache (socket 7 or below)

-Program basic chipset registers

Detect memory

-Auto-detection of DRAM size, type and ECC.

-Auto-detection of L2 cache (socket 7 or below)

Expand compressed BIOS code to DRAM

Call chipset hook to copy BIOS back to E000 & F000 shadow RAM.

Expand the Xgroup codes locating in physical address 1000:0

Reserved

67 Chapter 4

15h

16h

17h

18h

19h

1Ah

1Bh

1Ch

1Dh

1Eh

1Fh

20h

21h

22h

0Bh

0Ch

0Dh

0Eh

0Fh

10h

11h

12h

13h

14h

06h

07h

08h

09h

0Ah

03h

04h

05h

Checkpoint Description

Initial Superio_Early _Init switch

Reserved

1. Blank out screen

2. Clear CMOS error flag

Reserved

1. Clear 8042 interface

2. Initialize 8042 self-test

1. Test special keyboard controller for Winbond 977 series Super I/O chips.

2. Enable keyboard interface.

Reserved

1. Disable PS/2 mouse interface (optional)

2. Auto detect ports for keyboard & mouse followed by a port & interface swap (optional).

3. Reset keyboard for Winbond 977 series Super I/Q chips.

Reserved

Test F000h segment shadow to see whether it is R/W-able or not. If test fails, keep beeping the speaker.

Reserved

Auto detect flash type to load appropriate flash R/W codes into the run time area in F000 for ESCD & DMI support.

Reserved

Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real-time clock power status, and then check for override.

Reserved

Program chipset default values into chipset. Chipset default values are MODBINable by

OEM customers.

Reserved

Initial Early_Init_Onboard_Generator switch.

Reserved

Detect CPU information including brand, SMI type (Cyrix or Intel) and CPU level (586 or

686)

Reserved

Initial interrupts vector table. If no special specified, all H/W interrupts are directed to

SPURIOUS_INT_HDLR & S/W interrupts to SPURIOUS_soft_HDLR.

Reserved

Initial Early_PM_INIT switch.

Reserved

Load keyboard matrix (notebook platform)

Reserved

HPM initialization (notebook platform)

Reserved

Chapter 4 68

24h

25h

26h

27h

28h

29h

32h

33h

34h

35h

2Eh

2Fh

30h

31h

36h

37h

38h

39h

3Ah

3Fh

40h

41h

42h

3Bh

3Ch

3Dh

3Eh

2Ah

2Bh

2Ch

2Dh

23h

Checkpoint Description

1. Check validity of RTC value:

e.g. a value of 5Ah is an invalid value for RTC minute.

2. Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value

instead.

3. Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into

consideration of the ESCD’s legacy information.

4. Onboard clock generator initialization. Disable respective clock resource to empty PCI

& DIMM slots.

5. Early PCI initialization

-Enumerate PCI bus number

-Assign memory & I/O resource

-Search for a valid VGA device and VGA BIOS, and put it into C000:0

Reserved

Initialize INT 09 buffer

Reserved

1. Program CPU internal MTRR (P6 & PII) for 0-640K memory address.

2. Initialize the APIC for Pentium class CPU.

3. Program early chipset according to CMOS setup. Example: onboard IDE controller.

4. Measure CPU speed.

5. Invoke video BIOS.

Reserved

1. Initialize multi-language

2. Put information on screen display, including Award title, CPU type, CPU speed...

Reserved

Reset keyboard except Winbond 977 series Super I/O chips.

Reserved

Test 8254.

Reserved

Test 8259 interrupt mask bits for channel 1

Reserved

Test 8259 interrupt mask bits for channel 2.

Reserved

Chapter 4

53h

54h

55h

56h

57h

4Fh

50h

51h

52h

58h

59h

5Ah

5Bh

5Ch

5Dh

5Eh

5Fh

60h

61h

62h

63h

64h

65h

66h

4Ah

4Bh

4Ch

4Dh

4Eh

43h

44h

Checkpoint

45h

46h

47h

48h

49h

Description

Test 8259 functionality

Reserved

Initialize EISA slot

Reserved

1. Calculate total memory by testing the last double word of each 64K page.

2. Program writes allocation for AMD K5 CPU.

Reserved

1. Program MTRR of M1 CPU.

2. Initialize L2 cache for P6 class CPU & program CPU with proper cacheable range.

3. Initialize the APIC for P6 class CPU.

4. On MP platform, adjust the cacheable range to smaller one in case the cacheable

ranges between each CPU are not identical.

Reserved

Initialize USB

Reserved

Test all memory (clear all extended memory to 0)

Reserved

Display number of processors (multi-processor platform)

Reserved

1. Display PnP logo

2. Early ISA PnP initialization

-Assign CSN to every ISA PnP device.

Reserved

Initialize the combined Trend Anti-Virus code.

Reserved

(Optional Feature)

Show message for entering AWDFLASH.EXE from FDD (optional)

Reserved

1. Initialize Init_Onboard_Super_IO switch.

2. Initialize Init_Onboard_AUDIO switch.

Reserved

Okay to enter Setup utility; i.e. not until this POST stage can users enter the CMOS setup utility.

Reserved

Initialize PS/2 Mouse

Reserved

Chapter 4 70

78h

79h

7Ah

7Bh

74h

75h

76h

77h

7Ch

7Dh

7Eh

7Fh

6Eh

6Fh

70h

71h

72h

73h

67h

Checkpoint

68h

69h

6Ah

6Bh

6Ch

6Dh

80h

81h

82h

83h

84h

Description

Prepare memory size information for function call:

INT 15h ax=E820h

Reserved

Turn on L2 cache

Reserved

Program chipset registers according to items described in Setup& Auto-configuration table.

Reserved

1. Assign resources to all ISA PnP devices.

2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to

“AUTO”

Reserved

1. Initialize floppy controller

2. Set up floppy related fields in 40: hardware.

Reserved

(Optional Feature)

Enter AWDFLASH.EXE if:

-AWDFLASH is found in floppy drive

-ALT+F2 is pressed

Reserved

Detect & install all IDE devices: HDD, LS120, ZIP,CDROM.....

Reserved

Detect serial ports & parallel ports

Reserved

Detect & install co-processor

Reserved

1. Switch back to text mode if full screen logo is supported.

-If errors occur, report errors & wait for keys

-If no errors occur or F1 key is pressed to continue:

Clear EPA or customization logo.

Reserved

1. Call chipset power management hook.

2. Recover the text fond used by EPA logo (not for full screen logo)

3. If password is set, ask for password.

Save all data in stack back to CMOS.

Initialize ISA PnP boot devices.

Chapter 4

85h

Checkpoint

86h

87h

88h

89h

90h

91h

92h

93h

94h

95h

96h

FFh

1. USB final Initialization

2. NET PC: Build SYSID structure

3. Switch screen back to text mode.

4. Set up ACPI table at top of memory.

5. Invoke ISA adapter ROMs.

6. Assign IRQs to PCI devices

7. Initialize APM

8. Clear noise of IRQs/

Description

Reserved

Read HDD boot sector information for Trend Anti-Virus code

1. Enable L2 cache

2. Program boot up speed

3. Chipset final initialization

4. Power management final initialization

5. Clear screen & display summary table

6. Program K6 write allocation

7 Program P6 class write combining.

1. Program daylight saving

2. Update keyboard LED & typematic rate

1. Build MP table

2. Build & update ESCD

3. Set CMOS century to 20h or 19h

4. Load CMOS time into DOS timer tick

5. Build MSIRQ routing table

Boot attempt (INT 19h)

Chapter 4 72

POST Error Messages List

If you cannot run the diagnostics program tests but did receive a POST error message, use “POST Error

Messages List” to diagnose system problems. If you did not receive any error message, look for a description of your error symptoms in “Error Symptoms List” on page 75 .

NOTE: When you have deemed it necessary to replace an FRU, and have done so, you must run a total system check to ensure that no other activity has been affected by the change. This system check can be done through the diagnostics program.

NOTE: Check all power supply voltages, switch, and jumper settings before you replace the main board. Also check the power supply voltages if you have a “system no-power” condition.

If you are unable to correct the problem by using the “BIOS Messages List” table and “Error Symptoms List” table, go to “Undetermined Problems” on page 79.

To diagnose a problem, first find the BIOS error messages in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.

BIOS Messages

CMOS Battery Bad

CMOS Checksum Error

Disk Boot Failure

Diskette Drives or Types Mismatch Error

Display Switch Is Set Incorrectly

Display Type Has Changed Since Last Boot

Error Encountered Initializing Hard Drive

Error Encountered Initializing Hard Disk Controller

Floppy Disk CNTRLR Error or No CNTRLR Present

Keyboard Error or No Keyboard Present

Memory Address Error

Memory Parity Error

Action/FRU

Battery should be replaced

Check the battery and replace if necessary.

Insert system disk into Drive (A:) and press e .

NOTE: If you assumed the system would boot from the hard drive, make sure the controller is inserted correctly and all cables are properly attached. Also be sure the disk is formatted as a boot device. Then reboot the system.

Run Setup

Determine which setting is correct, and then either turn off the system and change the jumper, or enter Setup and change the VIDEO selection.

Configure the system for the new display type/

Be sure the adapter is installed correctly and all cables are correctly and firmly attached. Also be sure the correct hard drive type is selected in Setup .

Make sure the cord is correctly and firmly installed in the bus. Be sure the correct hard drive type is selected in

Setup. Also check if any jumper needs to be set correctly on the hard drive.

Make sure the controller is installed correctly and firmly. If there are no floppy drives installed, be sure the Diskette

Drive selection in Setup is set to None .

Make sure the keyboard is attached correctly and no keys are pressed during the boot.

NOTE: If you are purposely configuring the system without a keyboard, set the error halt condition in Setup to HALT ON ALL,

BUT KEYBOARD.This will cause BIOS to ignore the missing keyboard and continue the boot.

Use this location along with the memory map for your system to find and replace the bad memory chips.

Chapter 4

BIOS Messages

Memory Size Has Changed Since Last Boot

Memory Verify Error

Offending Address Not Found

Offending Segment

Press A Key To Reboot

Press F1 to Disable NMI, F2 to Reboot

RAM Parity Error

System Halted

Floppy Disk(s) Fail(80)

Floppy Disk(s) Fail (40)

Hard Disk(s) Fail (80)

Hard Disk(s) Fail (40)

Hard Disk(s) Fail (20)

Hard Disk(s) Fail (10)

Hard Disk(s) Fail (08)

Keyboard Is Locked Out

Keyboard Error Or No Keyboard Present

Manufacturing POST loop

BIOS ROM Checksum Error

Memory Test Fail

Action/FRU

In EISA mode, use Configuration Utility to reconfigure the memory configuration. In ISA mode, enter Setup and enter the new memory size in the memory fields.

Use this location along with your system’s memory map to locate the bad chip.

This message is used in conjunction with the I/O

CHANNEL CHECK and RAM PARITY ERROR messages when the segment that has caused problem cannot be isolated.

This message is used in conjunction with the I/O

CHANNEL CHECK and RAM PARITY ERROR messages when the segment that has caused problem cannot be isolated.

Press any key and the system will reboot.

When the BIOS detects a Non-maskable Interrupt condition during boot, this will allow you to disable the NMI and continue to boot, or you can reboot the system with the

NMI enabled.

Checking for segment

Press CTRL + ALT + DEL to reboot.

Or plug out AC and wait for 10 seconds, then plug in AC again. Press power button to boot the system again.

Unable to reset floppy subsystem

Floppy Type mismatch

HDD reset failed

HDD controller diagnostics failed

HDD initialization error

Unable to recalibrate fixed disk

Sector Verify failed

Unlock the key

Make sure the keyboard is attached correctly and no keys are pressed during the boot.

System will repeat POST procedure infinitely while the P15 of keyboard controller is pull low. This is also used for M/B burn in test.

BIOS will boot from the boot block and read BIOS binary file from FDD disk, then flash BIOS ROM (FWH - Firmware

Hub).

BIOS reports the memory test fail if the onboard memory is tested error

Chapter 4 74

Error Symptoms List

NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure,

replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/

FRU listed in right column is the most likely cause.

Error Symptom Action/FRU

Processor / Processor Fan

NOTE: Normally, the processor fan should be operative, and the processor clock setting should be exactly set to match its speed requirement before diagnosing any processor problems.

Processor fan does not run but power supply fan runs.

1. Ensure the system is not in power saving mode. See “Power

Management” in chapter 2.

2. With the system power on, measure the voltage of processor fan connector. Its reading should be +12Vdc. Its reading should be

+12Vdc. If the reading shows normal, but the fan still does not work, then replace a good fan.

3. Main board .

Processor test failed.

1. Processor.

2. Main board .

Main board and Memory

NOTE: Ensure the memory modules are installed properly and the contact leads are clean before diagnosing any system problems.

Memory test failed.

Incorrect memory size shown or repeated during POST.

System works but fails to enter power saving mode when the

Power Management Mode is set to

Enabled

Blinking cursor only; system does not work.

1. See “Memory”

2. Main board

1. Insert the memory modules in the DIMM sockets properly, then reboot the system.

2. Memory module.

3. Main board.

1. Enter BIOS Setup and load default settings.

In Windows Systems, check settings in Power Management

Property of Control Panel.

2. Reload software from Recovery CD.

1. Diskette/IDE drive connection/cables

2. Diskette/IDE disk drives

3. See “Undetermined Problems”.

4. Main board

Diskette Drive

NOTE: Ensure the diskette drive is auto-setting in BIOS Setup and its read/write head is clean before diagnosing any diskette drive problems.(If only one drive is installed, please make sure the drive is connected to master connector or the drive is set to master.)

Media and drive are mismatched.

Diskette drive does not work.

Diskette drive read/write error.

1. Ensure the diskette drive is configured correctly in the Disk

Drives of BIOS Setup.

2. Ensure the diskette drive is correctly formatted.

3. Diskette drive connection/cable

4. Diskette drive

5. Main board

1. Ensure the diskette drive is not set to

None

in the Disk Drives of

BIOS Setup.

2. Diskette drive power

3. Diskette drive connection/cable

4. Diskette drive

5. Main board

1. Diskette.

2. Ensure the diskette drive is not set to

Write protect in the

Security Options of BIOS Setup.

3. Diskette drive cable.

4. Diskette drive.

5. Main board.

Chapter 4

Error Symptom

Diskette drive LED comes on for more than 2 minutes when reading data.

Action/FRU

1. Diskette

2. Diskette drive connection/cable

3. Diskette drive

4. Main board

Diskette drive LED fails to light, and the drive is unable to access for more than 2 minutes.

Diskette drive test failed.

1. Diskette

2. Diskette drive power

3. Diskette drive connection/cable

4. Diskette drive

5. Main board

1. Diskette

2. Diskette drive

3. Diskette drive cable

4. Main board

Hard Disk Drive

NOTE: Ensure hard disk drive is configured correctly in BIOS Setup, cable/jumper are set correctly before diagnosing any hard disk drive problems. (If only one drive is installed, please make sure the drive is connected to master connector or the drive is set to master.)

Hard disk drive test failed.

1. Enter BIOS Setup and Load default settings.

2. Hard disk drive cable.

3. Hard disk drive.

4. Main board.

Hard disk drive cannot format completely.

Hard disk drive has write error.

Hard disk drive LED fails to light, but system operates normally.

Real-time clock is inaccurate.

1. Enter BIOS Setup and Load default settings.

2. Hard disk drive cable.

3. Hard disk drive.

4. Main board.

1. Enter BIOS Setup and Load default settings.

2. Hard disk drive.

1. With the system power on, measure the voltage of hard disk LED connector.

2. Hard drive LED cable.

CD/DVD-ROM drive LED doesn't come on but works normally.

CD/DVD-ROM Drive

NOTE: Ensure CD/DVD-ROM drive is configured correctly in BIOS Setup, cable/jumper are set correctly and its laser beam is clean before diagnosing any CD/DVD-ROM drive problems.

1. CD/DVD-ROM drive

CD/DVD-ROM drive LED flashes for more than 30 seconds before LED shutting off.

1. CD/DVD-ROM may have dirt or foreign material on it. Check with a known good disc.

2. CD/DVD-ROM is not inserted properly.

3. CD/DVD-ROM is damaged.

Software asks to reinstall disc.

Software displays a reading CD/DVD error.

CD/DVD-ROM drive cannot load or eject when the system is turned on and its eject button is pressed and held.

CD/DVD-ROM drive does not read and there are no messages are displayed.

CD/DVD-ROM drive can play audio CD but no sound output.

1. Disconnect all cables from CD/DVD-ROM drive except power cable, then press eject button to try to unload the disk.

2. CD/DVD-ROM drive power.

3. CD/DVD-ROM drive

1. CD may have dirt or foreign material on it. Check with a known good disc.

2. Ensure the CD/DVD-ROM driver is installed properly.

3. CD/DVD-ROM drive.

1. Ensure the headphone jack of the CD/DVD-ROM has an output.

2. Turn up the sound volume.

3. Speaker power/connection/cable.

4. CD/DVD-ROM drive.

Real-Time Clock

1. Ensure the information in the

Date and Time of BIOS Setup is set correctly.

2. RTC battery.

3. Main board

Chapter 4 76

Error Symptom

Video memory test failed.

Video adapter failed.

Display problem:

- Incorrect colors

No high intensity

Missing, broken, or incorrect characters

Blank monitor (dark)

Blank monitor (bright)

Distorted image

Unreadable monitor

Undetermined Problems

If an error message is present, go to “POST Error Messages List” on page 73. If you did not receive any messages, if the symptom is listed in “or “Error Symptoms List” on page 75 . If you still cannot solve the problem, continue with this check:

Check the power supply voltages. If the voltages are correct continue with the following steps:

Power off the system unit.

Perform the following checks, one by one, until you have isolated the problem FRU.

Load default settings in setup.

Check all main board jumper positions and switch settings.

Check all adapter card jumper positions.

Check all device jumper positions.

Check all cables and connectors for proper installation.

If the jumpers, switches and voltage settings are correct, remove or disconnect the following, one at a time:

10.

Non-Acer devices

External devices

Any adapter card (modem card, LAN card or video card, if installed)

CD/DVD-ROM drive

Diskette drive

Hard disk drive

DIMM

Processor

Main board

11.

Power on the system unit.

12.

Repeat steps 2 through 5 until you find the failing device or adapter.

79 Chapter 4

Jumper and Connector Information

Jumpers and Connectors

Refer to the following figure for the location of the jumpers and connectors on the main board:

Main board (Veriton 5200)

Chapter 5

Chapter 5 80

Main board (Veriton 5200D)

FN1

DIMM 2

DIMM 1

U12

CN10

JP1

CNM1

CN6

CN2

CN4

CN5

CN9

CN19

CN17

CN16

CNSW1

U21

JP14

CN21

CN20

JP3

AGP

PCI 3

PCI 2

PCI 1

U29

81 Chapter 5

Connector Description

Label

AGP

BT1

CN2

CN3

CN4

CN5

CN6

CN7

CN8

CN9

CN10

CN14

CN15

CN16

CN17

CN19

CN20

CN21

Component

AGP slot

Battery

PS/2 mouse (upper) and keyboard (lower) ports

Power connector

Network (upper) and USB (lower) ports

Parallel port (upper) and serial ports (lower )

Memory Stick Connector

CN23

CNX1

CNM1

CNSW1

DIMM1

DIMM2

DIMM3

Label

IDE 2 connector

IDE 1 connector

Game/MIDI (upper), line-out (left), line-in

(middle) and mic-in (right) connectors

Power connector (+12V)

CD-in connector

FDD connector

Intrusion connector

HDD LED connector

Power button

Front USB connector

Power/Suspend LED connector

NOTE: *Shared connection with serial por 2

Jumper Setting

FN1

FN2

FN3

PCI1

PCI2

PCI3

U12

U16

U21

U29

Component

EXT PCI slot

Audio FPIO connector

Smart card connector (com2)*

IDE cold swap pin

Memory slot 1

Memory slot 2

Memory slot 3 (not for Veriton

5200D)

3-pin fan SYS connector

3-pin fan CPU connector

3-pin fan SYS connector

PCI slot 1

PCI slot 2

PCI slot 3

CPU socket

Intel 845 socket

SMSC chipset

Intel ICH2 chipset

BIOS chipset

JP1

JP3

JP14

Jumper

LAN active LED connector

Function and settings

Model Select

1-2 Clear CMOS

2-3 Normal *

NOTE: *: Default Settings.

Chapter 5 82

83 Chapter 5

Chapter 6 FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Veriton 5200/

5200D. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise

Authorization).

IMPORTANT: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE

PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how best to dispose it, or follow the rules set by your regional Acer office on how to return it.

NOTE: The number indicates the location shown on exploded diagram or “NS” indicates “Not shown” on it.

Veriton 5200/5200D Exploded Diagram

85 Chapter 6

Picture

FDD/Floppy Disk Drive

No.

Partname

FDD,1.44MB PANASONIC/ JU-256A047P

V.H

Description

FDD 1.44 JU-256A047P ACER V.H

Cables

NS IDE CABLE,40PIN,3C 150+300MM C.A 40P 3C 150+300MM IDE H61

NS FDD CABLE,34PIN,2C 450MM C.A 34P 2C 450MM FDD H61

NS HDD CABLE 40PIN 3C 150+300MM ATA66 C.A. 40P 3C 150+300MM ATA66 H61

NS AUDIO BOARD CABLE,4PIN,2C 520MM W.A 4P 2C AUDIO 520MM H61

NS AUDIO BOARD CABLE,6/5 PIN 385MM

520MM

W.A 6/5P 385MM S58M AUDIO BD

Chapter 6 86

Picture No.

Partname

USB CABLE,10PIN 262MM

Description

C.A USB/10P 260MM H61

1-12 LED CABLE MODULE ASSY LED CABLE H40

1-8 POWER SWITCH CABLE 2PIN 300MM W.A 2P/PWR SW 300MM H61 W/HOLD

1-13 MICRO/SWITCH CABLE MODULE ASSY MICRO/SW CABLE H40 VT5100

Main Board

NS MAINBOARD/S81M S81M MB

Boards

NS AUDIO/USB BOARD S58M AUDIO/USB BOARD

87 Chapter 6

Picture

Power Supply

No.

Partname

POWER SUPPLY,200W,DELTA/DPS-

200BP-112B

Description

SPS 200W DELTA/DPS-200BP-112B

Case/Cover/Bracket assembly

1-11 FRONT PANEL ASSY F PNL VER H40 PRINT ACER

1-9 UPPER CASE ASSY UPPER CASE H40

1-10

1-3

1-4

LOWER CASE

EMPTY COVER 5.25”

KEY LOCK

LINK BAR

ASSY L CASE H40

5.25” EMPTY COVER H40 VERITON

KEY LOCK SUS430 IDK

BAR LINK SECC T-.8 H40

Chapter 6 88

Battery

Picture No.

NS FOOT STAND

Partname

NS RTC BATTERY LI 3V

Description

ASSY FOOT STAND H40/VERITON

BATTERY LI 3V CR2032 200MAH

Keyboard

NS KEYBOARD 104KEY US

Screws

Miscellaneous parts

4 &

1-14

4 &

1-14

4 &

1-14

SCREW PACK

SCREW

NS NAME PLATE

KB 104KEY DFE/6511-UV41 US

ASSEMBLY SCREW PACK

SCRW TAP HEX ZINC M3*.5*5

SCRW TAP HEX ZINC #6-32*4/16”

SCRW MACH FLAT M3*0.5P*8L NI

NAME PLATE 49.6*9.6MM S81M 520

NS NAME PLATE NAME PLT W/O COL 10.25*20.75 PC

89 Chapter 6

Chapter 6 90

Appendix A

Model Definition and Configuration

Veriton 5200

Brand No: S81M MB

Project Name/ Code: S81M /91.37P01.601

Description

S81M uses INTEL Pentium 4 processor in the 478 Pin package and the Northwood Processor with the

Brookdale chipset delivers a high performance and professional desktop platform solution.

With INTEL chipsets Brookdale MCH and ICH2, S81M provides the processor interface, DRAM interface, AGP interface, and HUB interface. The CPU interface supports the INTEL Pentium 4 processor subset of the

Extended Mode of Scalable Bus Protocol. INTEL Brookdale is optimized for the INTEL Pentium 4 processor and INTEL Northwood processor. It supports a single channel of PC133 SDRAM. The MCH contains advanced power management logic.

Veriton 5200D

Brand No: S82M MB

Project Name/ Code: S82M / 91.31Q01.401

Description

Veriton 5200D uses INTEL Pentium IV processor in the 478 Pin package and the Northwood Processor with the Brookdale chipset delivers a high performance and professional desktop platform solution.

With INTEL chipsets i845D and ICH2, S82M provides the processor interface, DDR RAM interface, AGP interface, and HUB interface. The CPU interface supports the INTEL Pentium 4 processor subset of the

Extended Mode of Scalable Bus Protocol. INTEL i845D is optimized for the INTEL Pentium 4 processor and

INTEL processor. The MCH contains advanced power management logic.

Appendix A 91

Main Features

Single Intel Pentium 4/ Northwood processor configurations at 400MT/ s

GTL+ host bus with integrated termination supporting 32 bit host addressing

Up to 3 GB (W/ 512Mb technology) of PC133 SDRAM

1.5v AGP interface with 4 x SBA/ Data Transfer and 2x / 4x Fast Write capability

8 bit, 66MHz 4x hub interface for highly concurrent operation

3 * 184 pin DIMM sockets (4M/ 8M/ 16M/ 32M/ 64M/ 128M/ 256M/ 512M DRAMs)

ACPI 1.0 Power management compliant

CPU clock throttling and clock stop control for complete ACPI S0 to S5 state support

ACPI compliance BIOS

ATA compliance hard disk power saving feature support Ultra DMA 100/ 66/ 33 on-board PCI master enhanced local bus IDE

PIO mode 4

Multiword DMA Mode 4

Ultra DMA/ 33/ 66/ 100 on-board serial ports - 2 high speed NS16C550 compatible UARTs with 16 byte FIFOs on-board parallel Port - SPP, EPP and ECP ( IEEE 1284 compliant ) on-board FDD interface - 1.2MB/ 1.44MB/ 2.88MB & 3 mode FDD

PS/2 keyboard

PS/2 mouse

Plug-and-Play (PnP) feature

Four USB connectors (Two USB on Port bracket, the other two on front panel)

On board AC 97 Codec. (Realtex 201)

On board RJ45 connector with Kinnereth PHY Chip for 10/100 Ethernet (Option)

1 AGP 4x Slot

3 + 2 PCI slots (with Golden finger for expanding)

Software shutdown foe Windows 98, 2000, ME

92 Appendix A

Appendix A 93

Appendix B

Test Compatible Components

This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Microsoft Windows XP Personal/Professional (Beta), Microsoft Windows ME (EN/

TW) Environment, Microsoft Windows 2000 Professional (EN/TW), Microsoft Windows 98SE Environment

(Driver Verify), Microsoft NT4.0 Workstation Environment (Driver Verify), Novell Netware 4.2 & 5.1

Environment and Linux Red Hat Environment.

Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.

Regarding configuration, combination and test procedures, please refer to the Veriton 5200/5200D

Compatibility Test Report released by the Acer Desktop System Testing Department.

Appendix B 94

Microsoft Windows XP Personal/ Professional (Beta) Test

Processor

Memory

FDD

HDD

CD-ROW

DVD-ROM

CD-RW

Mouse

Keyboard

VGA Adapter

Sound/MPEG Adapter

LAN Adapter

USB Devices

Item

Fax/Modem Adapter

Specifications

Pentium 4 1.5GHz

Pentium 4 1.7GHz

Pentium 4 1.8GHz

Pentium 4 1.9GHz

128MB

256MB

Panasonic JU256A046P

Seagate U6 20G 5400rpm

Seagate U6 40G 5400rpm

IBM Ericson 40G 7200rpm

AOpen 52X

Pioneer 16X

AOpen 12x/0X/32

Wheel Logitech /S48A S61

Logitec/930541-000 S59P

Logitec Wheel USB Mouse

Darfon USB Keyboard

Leadtek Winfast 3D M64 B6

Leadtek Winfast 2MX32LP

ATI Radeo VE 32M CRT+TV

Onboard AD 1885

Diamond Monster Sound M80 PCI Card

Creative Sound Blaster PCI 64

On-Die LAN

3COM 3C905C-TXM

Ambit 56K HCF

Askey V.90 56K D/F HCF

HP Desk Jet 895C USB Printer

Logitech Pagescan USB

AcerScan Prisa 310U

Charming USB Powered Speaker

Acer USB Video Capture Kit (DVC-V6) iomega ZIP 100 USB

95 Appendix B

Microsoft Windows ME (EN/TW) Environment Test

Processor

Memory

FDD

HDD

CD-ROW

DVD-ROM

CD-RW

Modem

Mouse

Keyboard

VGA Adapter

LAN Adapter

Fax/Modem Adapter

USB Joystick/Game Pad

USB Devices

Printer

Item

Sound/MPEG Adapter

Specifications

Pentium 4 1.5GHz

Pentium 4 1.7GHz

Pentium 4 1.8GHz

Pentium 4 1.9GHz

128 MB

256 MB

Panasonic JU256A046P

Seagate U6 20G 5400rpm

Seagate U6 40G 5400rpm

IBM Ericson 40G 7200rpm

AOpen 52X

Pioneer 16X

AOpen 12x/0X/32

Ambit 56K, HCF

Askey V.90, 56K,D/F, HCF

Wheel Logitech /S48A S61

Logitec/930541-000 S59P

Darfon US 104 Keys

Leadtek Winfast 3D M64 B6

Leadtek Winfast 2MX32LP

ATI Radeo VE 32M CRT+TV

Onboard AD 1885

Diamond Monster Sound M80 PCI Card

Creative Sound Blaster PCI 64

On-Die LAN

3Com 3C905CX-TXM

Ambit 56K HCF

Askey V.90 56K D/F HCF

Microsoft SideWinder Precision Pro USB

Primax RAPTOR 3D USB Gamestick

DEXXA USB Joystick J-ZB13

HP Desk Jet 895C USB Printer

Logitech Pagescan USB

AcerScan Prisa 310U

Charming USB Powered Speaker

Acer USB Video Capture Kit (DVC-V6) iomega ZIP 100 USB

HP Desk Jet 695C

Epson Stylus Color 440

Brother HL-660 6PPM Laser Printer

Appendix B 96

Microsoft Windows 2000 Professional Environment Test

Processor

Memory

FDD

HDD

CD-ROW

DVD-ROM

CD-RW

Mouse

Keyboard

VGA Adapter

Sound Adapter

LAN Adapter

USB Devices

Item

Fax/Modem Adapter

Specifications

Pentium 4 1.5GHz

Pentium 4 1.7GHz

Pentium 4 1.8GHz

Pentium 4 1.9GHz

128 MB

256 MB

Panasonic JU256A046P

Seagate U6 20G 5400rpm

Seagate U6 40G 5400rpm

IBM Ericson 40G 7200rpm

AOpen 52X

Pioneer 16X

AOpen 12x/0X/32

Wheel Logitech /S48A S61

Logitec/930541-000 S59P

Darfon US 104 Keys

Leadtek Winfast 3D M64 B6

Leadtek Winfast 2MX32LP

ATI Radeo VE 32M CRT+TV

Onboard AD 1885

Diamond Monster Sound M80 PCI Card

Creative Sound Blaster PCI 64

On-Die LAN

3Com 3C905CX-TXM

Ambit 56K HCF

Askey V.90 56K D/F HCF

HP Desk Jet 895C USB Printer

Logitech Pagescan USB

AcerScan Prisa 310U

Charming USB Powered Speaker

Acer USB Video Capture Kit (DVC-V6) iomega ZIP 100 USB

97 Appendix B

Microsoft NT 4.0 Workstation Environment Test (Driver Verify)

Item

Processor

Memory

FDD

HDD

CD-ROW

DVD-ROM

CD-RW

Modem

Mouse

Keyboard

VGA Adapter

LAN Adapter

Pentium 4 1.5GHz

Pentium 4 1.7GHz

Pentium 4 1.8GHz

Pentium 4 1.9GHz

128 MB

Panasonic JU256A046P

Seagate U6 20G 5400rpm

Seagate U6 40G 5400rpm

IBM Ericson 40G 7200rpm

Specifications

AOpen 52X

Pioneer 16X

AOpen 12x/0X/32

Ambit 56K, HCF

Askey V.90, 56K,D/F, HCF

Wheel Logitech /S48A S61

Logitec/930541-000 S59P

Darfon US 104 Keys

Leadtek Winfast 3D M64 B6

Leadtek Winfast 2MX32LP

ATI Radeo VE 32M CRT+TV

On-Die LAN

3Com 3C905CX-TXM

Appendix B 98

Microsoft Windows 98SE Environment Test (Driver Verify)

Item

Processor

Memory

FDD

HDD

CD-ROW

DVD-ROM

CD-RW

Modem

Mouse

Keyboard

VGA Adapter

LAN Adapter

Pentium 4 1.5GHz

Pentium 4 1.7GHz

Pentium 4 1.8GHz

Pentium 4 1.9GHz

128 MB

256 MB

Panasonic JU256A046P

Seagate U6 20G 5400rpm

Seagate U6 40G 5400rpm

IBM Ericson 40G 7200rpm

Specifications

AOpen 52X

Pioneer 16X

AOpen 12x/0X/32

Ambit 56K, HCF

Askey V.90, 56K,D/F, HCF

Wheel Logitech /S48A S61

Logitec/930541-000 S59P

Darfon US 104 Keys

Leadtek Winfast 3D M64 B6

Leadtek Winfast 2MX32LP

ATI Radeo VE 32M CRT+TV

On-Die LAN

3Com 3C905CX-TXM

99 Appendix B

Novell Netware 4.12 & 5.1 Environment Test

Processor

Item

Memory

FDD

HDD

CD-ROW

DVD-ROM

CD-RW

Modem

Mouse

Keyboard

VGA Adapter

LAN Adapter

Specifications

Pentium 4 1.5GHz

Pentium 4 1.7GHz

Pentium 4 1.8GHz

Pentium 4 1.9GHz

128 MB

256 MB

Panasonic JU256A046P

Seagate U6 20G 5400rpm

Seagate U6 40G 5400rpm

IBM Ericson 40G 7200rpm

AOpen 52X

Pioneer 16X

AOpen 12x/0X/32

Ambit 56K, HCF

Askey V.90, 56K,D/F, HCF

Wheel Logitech /S48A S61

Logitec/930541-000 S59P

Darfon US 104 Keys

Leadtek Winfast 3D M64 B6

Leadtek Winfast 2MX32LP

ATI Radeo VE 32M CRT+TV

On-Die LAN

3Com 3C905CX-TXM

Appendix B 100

Linux Red Hat Environment Test

Item

Processor

Memory

FDD

HDD

CD-ROW

DVD-ROM

CD-RW

Modem

Mouse

Keyboard

VGA Adapter

LAN Adapter

Specifications

Pentium 4 1.4GHz

Pentium 4 1.5GHz

Pentium 4 1.7GHz

128 MB

256 MB

Panasonic JU256A046P

Seagate U6 20G 5400rpm

Seagate U6 40G 5400rpm

IBM Ericson 40G 7200rpm

AOpen 52X

Pioneer 16X

AOpen 12x/0X/32

Ambit 56K, HCF

Askey V.90, 56K,D/F, HCF

Wheel Logitech /S48A S61

Logitec/930541-000 S59P

Darfon US 104 Keys

Leadtek Winfast 3D M64 B6

Leadtek Winfast 2MX32LP

ATI Radeo VE 32M CRT+TV

On-Die LAN

3Com 3C905CX-TXM

101 Appendix B

Appendix C

Online Support Information

This section describes online technical support services available to help you repair your Acer Systems.

If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.

Acer's Website offers you convenient and valuable support resources whenever you need them.

In the Technical Information section you can download information on all of Acer's Notebook, Desktop and

Server models including:

Service guides for all models

User's manuals

Training materials

Bios updates

Software utilities

Spare parts lists

Chips

TABs (Technical Announcement Bulletin)

For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our technical material.

Also contained on this website are:

Detailed information on Acer's International Traveler's Warranty (ITW)

Returned material authorization procedures

An overview of all the support services we offer, accompanied by a list of telephone, fax and email contacts for all your technical queries.

We are always looking for ways to optimize and improve our services, so if you have any suggestions or comments, please do not hesitate to communicate these to us.

Appendix C 102

103 Appendix C

A

AGP Expansion Cards 64

Assignment Map 20

Audio controller 18

Audio Interface 18

Audio-in/Line-in port 7

Audio-out/Line-out port 7

B

Basic level 27

BIOS Setup 26

Entering Setup 27

Setup Utility 27

BIOS Utility

Disk Drives 29

Exiting Setup 48

Load Default Settings 47

Power Management 38

Product Information 28

System Security 44

Block Diagram 8, 9

C

D

Cache Memory 17 size 17 speed 17

Chipsets 22

CMOS Setup 26

Compatibility Test 94

Connectors 80

Description 82 description 82 controllers 22 audio 18 serial port 19

CPU removing 59, 60

CPU upgrade removing 59, 60

Current 23

Device Standby Mode 24

Index

I

disassembly

CD-ROM Drive 63

Power Supply 65

Disk Drives 29

IDE primary channel master 29

IDE primary channel slave 29

IDE secondary channel master 29

IDE secondary channel slave 29

DRQ Assignment Map 22

E

F

G

features 2, 92 connectivity 2 design 3 ergonomics 3

Multimedia 2

Performance 2

Floppy disk drive Interface 18

Frequency 23 front panel 4

FRU 84

Game/MIDI port 6

Global Standby Mode 24

H

ECP 19

Environmental Requirements 22

EPP 19

Expansion slot 7

Hard Disk Drive 61

Hardware Specifications and Configurations 15

Humidity 22

I/O Address Map 21

IDE Interface 18

IDSEL 20

Interface audio 18

IDE 18

Video 18

104

IRQ Assignment Map 21

J

K

keyboard 13

L

M

Load Default Settings 47

Machine Disassembly 56

Main board 80

Main Board Layout 9

Mechanical Specifications 23

Memory size 16 system 16

Memory Address Map 20

Model Definition 91

Modem 19 data 19 fax 19 voice 19

MPU-401 18

N

Network port 6

O

Jumper and Connector Information 80

Jumpers 80

Online Support Information 102

Overview 1, 91

P

Parallel Port 19

Parallel/printer port 6

Password bypassing 46 setting 44

PCI Expansion Cards 64

PCI INTx# 20

PCI Slot IRQ 20 ports left panel 6

POST 67

Power button 4

Power LED 4

105

R

Power Management 23, 38

Power-On Self-Test (POST) 67

Processor 59, 60 removing 59, 60

Product Information 28

DMI BIOS version 28 main board ID 28 product name 28 system BIOS version 28 system serial number 28

PS/2 keyboard port 6

PS/2 mouse port 6

Removal and Replacement 56 removing 59, 60

Replacement

Assembly, Machine 56 replacing HDD 61

RMA 84

Routing Map 20

S

Security 44

Serial Port 19

Serial port 7 socket memory 16

Socket 370 15

Suspend Mode 24

Switching

Power Supply 102W 23

Symptoms List

Audio 77

CD/DVD-ROM Drive 76

Diskette Drive 75

Keyboard 78

Memory 75

Modem 77

Monitor 77

Other 78

Parallel Port 78

Power Supply 78

Processor / Processor Fan 75

Real-Time Clock 76

Serial Port 78

System Board 75

Video 77

System 26

System Specifications 1, 91 design 3

Features 2, 92

Index

System Utilities 26

Disk Drives 29

Exiting Setup 48

Load Default Settings 47

Power Management 38

Product Information 28

System Security 44

T

U

Temperature 22

Test Compatible Components 94

Troubleshooting 66

UART 19

Undetermined Problems 79

USB Port 19

USB ports 6

V

W

Veriton 91

Vibration 22

Voltage 23

Voltage selector switch 7

Weight 23

Win95/Win2000 Environment Test 97

Windows 98 Environment Test 95

Index 106

107 Index