AURAJET™ HANDSET
Installation Guide
Technical Specifications:
Operating Pressure:
Min: 100kPa/1bar
Max: 500kPa/5bar*
Optimum: 150kPa/1.5bar - 500kPa/5bar
Operating Temperature:
Hot: Max 65°C*
Cold: Min 5°C
Inlet Connections:
½" BSP
* Regional specific regulations apply.
Please refer to your warranty statement at www.methven.com
www.methven.com
•
•
•
•
IMPORTANT: Please read all of the instructions before installation.
General:
• Methven recommends this product is installed by a licensed plumber in compliance with all relevant regional regulations.
After installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per regional regulations.
It is the responsibility of the installer to ensure a waterproof seal is achieved.
NOTE: Some showers may not provide an effective shower when used with gravity fed heated water systems or where pressures are less than 150kPa/1.5bar at the outlet. Additionally showers with flow rates of less than 9L/min may not allow the following to function correctly:
- some instantaneous water heaters
- some tempering valves
- some thermostatic mixing valves
Care and Cleaning:
Run hot water through shower for 2 minutes before first use.
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with contamination free warm soapy water and a damp soft cloth.
A filter washer should be installed in the hose cone on the water outlet and it should be cleaned periodically.
If shower performance is compromised by the build-up of lime-scale, soak in limescale remover for up to 10 minutes. Do not attempt to remove limescale with sharp objects or abrasives. Do not use products containing chlorine bleach or hydrochloric acid as these can damage the shower. Always rinse the shower thoroughly after cleaning to remove cleaning products that can damage the shower.
Never insert objects into the spray slot or attempt to remove spray cover as this may cause damage to shower components.
Methven warrants this product against manufacturing defects and that it is suitable for use under the general operating conditions specified in this instruction sheet. However, regional regulations apply and may affect your warranty. Please refer to www.methven.com
or call customer service for full details.
New Zealand
0800 804 222
439910
Australia
1300 638 483
UK
0800 195 1602
ISSUE C
CARE AND CLEANING:
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with contamination free warm soapy water and a damp soft cloth.
Clean filter washer periodically
OVAL RAIL
439972 ISSUE A
•
•
•
•
•
1.
Slider
Water Outlet
(If supplied)
Soap Dish
(If supplied)
5.
1.
Match the mountings to wall bosses and push into place
2.
Slide the rail up or down to centralise brackets.
2.
grub screw topside
6.
Wall Boss Housing
Internal Mounting
Bracket and Screw
Rail
Wall Boss Screws
Grub Srew grub screw underside
Secure the wall boss housings.
NOTE: Ensure protection pads are used between wall bosses and tiles.
FLOOR
7.
1.
Remove the rail and tighten the tensioning screws until they lock.
2.
Relocate the rail onto wall bosses and tighten grub screws top and bottom.
3.
IF SOAP DISH IS
SUPPLIED:
Slide soap dish onto the rail.
To adjust the slider height push the button and slide to desired height.
4.
1.
Fit the internal mounting brackets by locating in slot rotating 90 ° as shown.
2.
Tighten the screws finger-tight using
Allen key.
8.
Water Outlet
(If supplied) Methven Handset
(If supplied)
Flat Washer
Swivelling
Cone
Filter Washer
Non-Swivelling
Cone
IF HANDSET, HOSE OR WATER OUTLET ARE SUPPLIED:
Connect hose to water outlet and Methven handset. Ensure swivelling cone is connected to the handset.
