Soundstream SR5.3500D Amplifier 3500W Max Power Output Owner’s Manual

SOUNDSTREAM
REIGN
Owner’s Manual EN
| 5-Channel Amplifier
(Analog and Digital system)
SR5-3500D
Features & Functions:
Sub Sonic
This eliminates the lowest frequencies and protects
the speakers from damage. Switch the frequency
10Hz or 50Hz depending on the size of the installed
subwoofer. Bass Boost Control
The Bass Boost Control allows
you to control extra bass
Input-RCA (Front) response into your system. The
Full range line input to L.P.F Bass can be boosted up from 0
connect with the source LL to +12dB
unit RCA output. Set lowpass
frequency: from
Gai 40H2-250Hz Input-RCA (Rear)
am . Full range line input to
Adjust the gain value connect with the source
from “MIN” to “MAX” unit RCA output.
SUB SONIC LPF
10Hz ЗОН
IN HPF
CROSSOVER e
80 qa
40Hz 250Hz
HPF
HPF
REMOTE
& ©
Input-RCA ( Subwoofer)
Full range line input to
connect with the source
unit RCA output.
I
Gain
Adjust the gain value
from “MIN” to “MAX”
Position H.P.F
Highpass (frequency response
is limited downwards. )
Position FULL
Provide a full range signal to the
speakers ( whole frequency
response).
H.P.F
Set highpass frequency: from
80Hz-1.2kHz
Gain
Adjust the gain value
from “MIN” to “MAX”
Position H.P.F
Highpass (frequency response
is limited downwards. )
Position FULL
Provide a full range signal to the
speakers ( whole frequency
response).
Features & Functions:
Fuse
The integrated amplifier fuses protect the units from short circuit and overload
Speaker Terminals:
The speaker terminals are Gold Plated for high conductivity
and minimum impedance loss. Be sure to strip just enough
insulation off your speaker wires that will fit under the screw
plate to help ensure against speaker wire short circuits.
The unit can support an impedance load as low as 2ohms per
channel or 4 ohms in the bridged mode.
Bridged mode is designed for 4-8 ohm loads and will not
supports a 2 ohm load.
sa
FR FO OR RO Y
LED - Prote tion / Power
When the unit is protection, the protection
LED will light up.
If remote power signal, the Power LED will
light up indicating power condition are correct.
Ground Connection
to vehicle's chassis
Battery
12V
Remote Wire
(REM) . Connection
Power Terminals:
B+/+12V . Connect the +12V pole of power supply directly to the
battery(+) position.
GND. Connect the GND pole of power supply directly to the (-)
negative ground battery terminal of car chassis.
REM. Connect the “Remote” pole to external switch for positive
12V ON/OFF. This may e connected to the power antenna of turn
on lead of the headunit.
Power Connection:
For your convenience, high current barrier strip terminals are provided
which allow the use of heavy gauge terminals and wire without splicing.
B+/+12V . Connect the +12V pole of battery.
GND . Connect the chassis ground of auto.
REM . Connect to the remote turn-on lead of your headunit.
Note:
Improper wiring connections can seriously damage amplifiers,
accessories, or speakers, please follow instructions carefully.
Disconnect the battery positive (+) before making any power
connections to the amplifier.
Make sure all connections are clean and secure, and use gromments
when going through the firewall and other metal bodywork.
Always use the proper size fusing, with a fuse at the battery and the
amplifier.(not supplied)
GND REM +12V
ale
Black | Red
Orange Connect to the remote
turn-on lead of your headunit.
Input Connection:
Connect the pre-amp( low-level) outputs from your source unit or
crossover to the RCA jacks labeled “input” on the amplifier. Be sure
to route all signal cable away from power lines and use high quality
RCA cables to insure good signal transfer and to avoid noise from
entering the system.
Inthe Stereo mode, connect the left and right RCA plugs from the
source unit to their appropriate input jacks.
Inthe Mono/Bridged mode, connections may be made to right, left
of both input jacks.
If you are using a pre-amp device, such as the G & Designs Aa4X,
connect the outputs of the front-end unit to the inputs of the pre-amp,
tien the outputs of the pre-amp to the inputs of the amplifier as per
above.
3
Input Connection:
Subwoofer Line-in
ou > Rear Line-in
<> <> <> <> <<
Front Line-in
REMOTE
FRONT SUB SONIC LPF BASS BOOST
@ @
10Hz 5082 40Hz 250Hz dB 12dB
HPF HPF GAIN
@saseiso©
FULL
rs
Output connection:
Again, high current barrier strip terminals are provide for connection to the loud
speaker system.
Inthe stereo mode, connect the left speaker lead to the left terminal and the right
speaker leads to the right terminal. Be sure to observe polarity.
Inthe Bridged/Mono mode, connect the speaker (+) lead to the R+ terminal and the
speaker(-) lead to the L- terminal.
Stereo/Mono configuration may be used bu utilizing the above wiring simultaneously.
(For satellite subwoofer or satellite / center).
Note: Mono mode is designed for 4-8 ohm load and will not support
a2 ohm load.
5 Channel Amplifier System:
Connect the two pairs of output and subwoofer terminals to corresponding
Left/Right/subwoofer speakers:
RL
SOURCE UNIT
Oooo Ooo
2 Channel Amplifier System:
This unit bridgeable from a 4.1 channel amplifier to a 2.1 channel amplifier. The ideal
speaker impedance for optimum operation is 4 ohms. The amplifier will provide stable
operation between 2 and 8 ohms loads.
When operating in the bridged mode, the minimum recommended speaker load is
4 ohms for each bridge channel. Operation of the amplifier below this impedance
load can damage both the amplifier and you speaker, and will void your warranty.
REM +12
8
FUSE
%
= ||;
Е]
== POWE! | INPUT
FR FR® @RR ROS м
Black Red —_
\ O
= И 2ooooo
TROUBLE SHOOTING
No Audio
e Low or no remote turn-on voltage: check remote connections at the amplifier
and sourceunit.
¢ Blown amplifier fuse: replace with a new fast-blow fuse (same rating).
e Power wires not connected: check battery and ground wiring at the amplifier
and check the battery connections.
e Speaker leads shorted: check speaker continuity to ground; it should not
show acommon ground.
e Speakers not connected or are blown: check speaker connections at the
a mplifier; measure coil impedance.
Distorted audio
e Gain is not properly set or the speaker cones are damaged.
e Review the instructions for setting the gain. Inspect each speaker cone for
signs of damage, such as a frozen cone, burning smell, etc.
6
Features:
*Full Range 2 ohm Stable 5-Channel Amplifier
«RMS Power Rating:
4 ohms: 100 watts x 4 chan., 350W x Sub chan.
2 ohms: 150 watts x 4 chan., 500W x Sub chan.
Bridged, 4 ohms: 300 watts x 2 chan., 500W x Sub chan.
«Total power output: 2200 watts
«Pulse Width Modulated MOSFET power supply
«Wired remote bass level control included
«LED power (green) and protect (red) indicators
«Soft start turn-on
«5/3 channel operation
«3-way protection circuitry (thermal, overload, and speaker short protection)
«Dual speaker terminals simplify the hookup of multiple speakers
«Heavy duty aluminum alloy heat-sink
Input sensitivity: 200mV - 6V
«Variable high-pass filter: 80- 1200 Hz, 12 dB/octave
«Variable low-pass filter: 40 - 250 Hz, 12 dB/octave
«Variable Bass Boost: O to +12 dB bass boost
Specification:
4x140W + 1x300W(4Q RMS)
Output Power: | 4x220W +1X500W(2Q RMS)
Bridged:2x440W(40 RMS) +1x500W(20 RMS)
THD: | <0.3%
Frequency RESP: | 10Hz — 20kHz +2dB
S/N Ratio: | 290
Input Sensitivity: | 200mV — 8V
Bass Boost: 12dB
Speaker Impedance: 2-80
Power Fuse: 40Ax2 ( Refer flank text)
Dimension (HxWxL): SR5-3500D 2.2"H x 8.5"W x161"L
Accessory: Screws Set & Spare Fuse