6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-NY8315A
_R1
For Style NY8315A
Please go to www.quoizel.com
for product cleaning tips. Go to the Care + Maintenance selection.
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) Medium Base Bulb 150W Maximum
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Part
A
B
C
D
E
F
Description
Crossbar
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Fixture Body
Quantity
1 pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
1 pc.
A
B
C
D
E
F
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com
2017 QuoizelInc.
RevisedDate:2017-10-09
1of5
NY8315A
FINISH:
ANTIQUE BRASS
7” 6.75”
12.5”
7”
3.5”
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2 "
2of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-NY8315A
_R1
For Style NY8315A
STEP 1
-
Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on the backplate of the Fixture Body (K).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex
Nut (D) onto the Mounting Screws (B). Hand tighten until snug.
Mounting
Screw
Lock Washer
Crossbar
Hex Nut
Figure 1
Fixture
Body
STEP 2
-
Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Mounting Hole
Crossbar
Outlet Box
Outlet Box
Screw
Figure 2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com
2017 QuoizelInc.
RevisedDate:2017-10-09
3of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-NY8315A
_R1
For Style NY8315A
STEP 3
-
Wire Connections
A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw.
B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.
White wire from outlet box
Black wire from outlet box (or Red)
Bare, or Green
Ground wire from outlet box
Green Ground Screw on the Crossbar
Figure 4
White wire from fixture
Black wire from fixture
Ground wire from Fixture
STEP 4
-
Attach Fixture Body to Mounting
Screw
A. Place the backplate of the Fixture Body (F) over the
Mounting Screws (B) and secure with Mounting
Balls (E). Hand tighten until snug.
Figure 3
Backplate
Mounting
Screw
Mounting Ball
Figure 5
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com
2017 QuoizelInc.
RevisedDate:2017-10-09
4of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-NY8315A
_R1
For Style NY8315A
STEP 5
-
Install Bulb
A. Insert the bulb onto the socket and screw snugly into place.
Bulb
Socket
Figure 6
Figure 7
STEP 6
-
Apply Silicone Sealer to Mounting
Balls
A. To prevent moisture from entering the wire compartment, apply a small amount of silicone sealer
(not included) to the threaded side of the mounting balls (E) and then install them onto the mounting screws (B). Wipe off excess caulk.
Mounting Ball
STEP 7
-
Apply Silicone Sealer to Backplate
A. Make sure exterior wall surface and fixture backplate are free of dirt before applying caulk. Using exterior grade caulk, start on one side of fixture backplate and follow contour, where the fixture backplate meets the exterior wall surface upward. Proceed to caulk over top of backplate and down other side. Do not caulk bottom of fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use.
Enjoy!
Exterior Wall Surface
Outdoor Fixture
Backplate
Figure 8
Exterior
Grade Caulk
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com
2017 QuoizelInc.
RevisedDate:2017-10-09
5of5
