Assembly Instruction Sheet #IS-SNN8406
For Styles SNN8406K, SNN8406PN and SNN8406W
Please go to www.quoizel.com
for product cleaning tips. Go to the Care + Maintenance selection.
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base bulb 100W Maximum.
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts.
Fixture can only be mounted in the direction indicated.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
A
Crossbar
Assembly x 1
C
Outlet Box Screw x 2
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw.
B. Use standard wire connectors (D) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.
E
Alternate
Mounting
Screw x 2
D
Wire Connector x 3
B
Fixture Body x 1
White wire from outlet box
Black wire from outlet box (or Red)
White wire from fixture
Black wire from fixture
STEP 1
-
Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(C). Tighten until snug
.
Bare, or Green
Ground wire from outlet box
Green Ground Screw on the Crossbar
STEP 4 Install Fixture Body
Ground wire from Fixture
Figure 3
Outlet
Box
A
C
Figure 1
Supply Wires with Ground Wire
STEP 2
-
Fit Backplate to
Crossbar Assembly
Backplate
A.
Remove mounting balls from the
Mounting
Screw
Mounting Ball
Crossbar Assembly (A). Fit the backplate on Fixture Body (B) to the Crossbar Assembly (A) and secure with mounting balls.
Note: The backplate on Fixture
Body (B) should be snug against the wall and the mounting balls.
A
B
If not, adjust the length of the mounting screw on the Crossbar
Assembly (A) by unscrewing the
Hex Nut and
Lock Washer preassembled hex nut and lock washer and then screwing the
Figure 2 mounting screws in or out of the crossbar until the correct length is achieved. Once the backplate on Fixture Body (B) is secure, remove the mounting ball and Fixture Body (B) and proceed to Step 3.
A. Carefully tuck all wires into the outlet box and position the backplate of Fixture Body (B) over the outlet box. Align the holes in the backplate with the mounting screws. Place caulk (not supplied) into the previously removed mounting balls and then attach Fixture
Body (B) using the mounting balls. Hand tighten until snug.
Mounting Screw
Figure 4
A
Backplate
Mounting Ball
B
2018 QuoizelInc.
visit us on-line at www.quoizel.com
1of2
ReleasedDate:2018-11-12
STEP 5
-
Install Bulb and
Silicone Sealer
Apply
A. This fixture uses standard bulb with medium base. Maximum 100 watts.
Insert bulb and screw snugly into place.
B. Make sure exterior wall surface and fixture backplate are free of dirt before applying caulk. Using exterior grade caulk, caulk over top of backplate and down other side.
Do not caulk bottom of fixture backplate to ensure proper moisture drainage.
Socket
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade
Caulk
Backplate
Bulb
Figure 5
HOW TO REPLACE GLASS PANELS
A. By unscrewing Allen Screws, remove the Cage from the Fixture
Hood.
B. Unscrew Screws on the top of the Cage. Remove the Glass Holder from the Cage. Remove the broken Glass Panel inside of the Cage and insert the replacement Glass
Panel.
C. Place the Glass Holder back onto the top of the Cage and secure with
Screws. Hand tighten until snug.
D. Attach the Cage with Glass Panels back onto the Fixture Hood and secure with Allen Screws. Hand tighten until snug.
Allen Screw
Fixture
Hood
Screw
Glass
Holder
Glass Panel
Cage
Figure 6
2015 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com
2of2
June2015
