windham

entryway bench style # WNBENCHXBK (black) dpci # 249-18-0087 tcin # 14402891 style # WNBENCHXBL (teal) dpci # 249-18-0086 tcin # 14402892 style # WNBENCHXRD (red) dpci # 249-18-0173 tcin # 16511324 style # WNBENCHXWH (shell) dpci # 249-18-0174 tcin # 16511323 style # WNBENCHXNV (navy) dpci # 249-18-0175 tcin # 16511322 style # WNBENCHXGY (elephant) dpci # 249-18-0374 tcin # 50541018

>> assembly instructions

© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2

Congratulations on your latest Target purchase.

Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.

All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time. Good luck—though we’re confident you won’t need it.

before you begin

1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.

2. Use the carton as a working surface to prevent product damage during assembly.

3. Read through and review assembly steps.

4. Gather all tools prior to assembly.

tools needed

table of contents

introduction

hardware

parts list

how to use the cam lock system

assembly

5

6

2

4

7-13

QUESTIONS?

Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling. 3

4

hardware

(H1) x 16 wooden dowel

(H6) x 2 knob bolt

(H2) x 8 cam bolt

(H7) x 8 flat-head screw

(H3) cam x 8

(H8) x 8 allen head bolt

(H4) x 22 pan-head screw

(H5) x 2 knob

(H9) x 8 lock washer

(H10) x 8 washer

(H11) x 1 allen wrench

(H12) x 2 magnetic catch

exploded diagram

5

10

11

8

9

6

7

ITEM DESCRIPTION QUANTITY

1 top panel 1

2

3

4 left side assembly right side assembly bottom panel

1

1

1 left partition right partition back panel left door right door foot support cushion

1

1

1

2

1

1

1

5

how to use the cam lock system

Screw cam bolt into panel Align cam bolt(s) with cam(s) and insert all the way into cross-bored hole(s)

Push cam into panel - arrow feature on cam top points to panel edge

6

Rotate cam(s) clockwise 180° to lock panels together

Panels should be tight against each other and connection should be rigid

step 1: attach magnets to left/right partitions then attach to bottom panel

finished edge

(H1) x 4 wooden dowel

(H2) x 4 cam bolt

(H3) x 4 cam

(H4) x 4 pan-head screw

(H12) x 2 magnetic catch

1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

1.2. Screw-In cam bolts must be screwed down flush.

1.3. Refer to page 6 for instructions on how to use the cam lock system.

1.4. Do not over tighten screws.

7

step 2: attach right side assembly

(H1) x 2 wooden dowel

(H8) x 2 allen head bolt

(H9) x 2 lock washer

(H10) x 2 washer

(H11) x 1 allen wrench

8

2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

2.2. Make sure bolts go through the pre-drilled holes properly.

2.3. Do not over tighten bolts.

step 3: attach left side assembly and foot supports

(H1) x 2 wooden dowel

(H8) x 2 allen head bolt

(H9) x 2 lock washer

(H10) x 2 washer

(H11) x 1 allen wrench

Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

3.2. Make sure bolts go through the pre-drilled holes properly.

3.3. Do not over tighten bolts.

9

step 4: attach top panel

(H1) x 8 wooden dowel

(H2) x 4 cam bolt

(H3) x 4 cam

(H8) x 4 allen head bolt

(H9) x 4 lock washer

(H10) x 4 washer

(H11) x 1 allen wrench

10

Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

4.2. Screw-in cam bolts must be screwed down flush with panel.

4.3. Refer to page 6 for instructions on how to use the cam lock system.

4.4. Make sure bolts go through the pre-drilled holes properly.

4.5. Do not over tighten bolts.

step 5: attach back panel

Begin by installing all of the screws along one edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is square. (If using a tape measure, the distance from one corner, diagonally to the other corner should be the same in both directions.) If not, apply gentle pressure to the diagonally opposite corners to shift case into alignment. Re-measure to ensure equal distances. Install the remaining screws, starting with the corners.

pre-drilled holes

(H4) x 18 pan-head screw

2

Make sure the screws go through the pre-drilled holes properly.

5.2. Do not over tighten screws.

7

1

11

step 6: attach knobs and left/right doors

(H5) x 2 knob

(H6) x 2 knob bolt

(H7) x 8 flat-head screw

12

6.1. Do not over tighten screws.

step 7: install cushion

13

200 lbs.

14

1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.

2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.

QUESTIONS?

Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

15