Glide VHD

User's Guide

< 70 lbs. (31.8 kg)

CAUTION: DO NOT EXCEED

MAXIMUM LISTED WEIGHT

CAPACITY. SERIOUS INJURY

OR PROPERTY DAMAGE MAY

OCCUR!

Reduce

Reuse

Recycle

English

For the latest User Installation Guide please visit: www.ergotron.com

English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语 www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

888-61-053-W-02 rev. F • 10/19 1 of 15

Hazard Symbols

Review

These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the signi fi cance of the following Safety Hazards if encountered on the product or within the documentation. Children who are not able to recognize and respond appropriately to

Safety Alerts should not use this product without adult supervision!

Symbol Signal Word

NOTE

CAUTION

WARNING

ELECTRICAL

Level of Hazard

A NOTE indicates important information that helps you make better use of this product.

A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

A WARNING indicates either potential for property damage, personal injury, or death.

An Electrical indicates an impending electrical hazard which, if not avoided, may result in personal injury, fi re and/or death.

Safety

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a diff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product and equipment.

Caution:

To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury.

Tools Needed

2 of 15

13mm

Stud Finder

HOLLOWWALL

Ø 1/2” (13 mm)

WOOD

Ø 7/32" (5.5 mm)

Ø 1/2" (13 mm)

CONCRETE

Ø 3/8" (9.5 mm)

888-61-053-W-02 rev. F • 10/19

Components

A

4x

1

M4 x 15mm

4x

4x

4x

B

M4 x 30mm

3

2

M6 x 15mm M6 x 30mm

4x

M6-M8 x 5mm

4x

16x

M6 x 8mm

1x

4x

4mm

M4-M5

4

4x

C

4x

M5 x 15mm

2x

2x

2x

2x

D

4x

4x

M5 x 30mm

4x

M8 x 15mm

4x

M8 x 30mm

4x

2x

8mm x 80mm

2x

M8

4x

1/4 - 20 x 1.5”

M8 x 15mm

4x

1x

5

2x

888-61-053-W-02 rev. F • 10/19 3 of 15

1

Determine Mounting Height

CAUTION: Before proceeding with this installation consult your TV product guide for manufacturer recommendations on choosing a mounting location that will ensure optimum TV performance. Location considerations might include: TV height and viewing angle - based on height and distance of seating, room dimensions and size of TV; access to power outlets; cable connections for speakers and other devices; protection from glare and heat, (windows, lamps, fi replace, air ducts) and vibration.

Please take into account that this product is being installed in it’s highest position. Your TV will only be able to be lowered from it’s installed position.

to predict what your TV confi guration will be. However, as a general guideline attach the mounting plate(bottom holes) 42" from fl oor for comfortable sit-stand viewing.

EXAMPLE:

If mounting a 46” - 65” diagonal TV with centrally located VESA hole pattern, locate the lowest set of mounting plate holes 42” from fl oor.

You can modify the mounting height according to your TV size, VESA location and personal preference. For more information, please contact Ergotron Customer Care at 800-888-8458, www.ergotron.com

4 of 15

(107cm)

Lowest mounting plate hole location.

16”

(40cm)

Travel

Down from mounting height

TV

65”

(165cm)

Mounting

Plate

Lowest

Position

Highest

Position

888-61-053-W-02 rev. F • 10/19

2

Attach Monitor

Option A

(>200mm x 200mm)

NOTE: M4 screws should not be used for hole patterns greater than 200m x 200m.

888-61-053-W-02 rev. F • 10/19 or or or or or or or or

5 of 15

Attach Monitor

Option B

(200mm x 200mm/Adapter Use)

4x 4x

M8

M8 x 15mm

A. Attach Adapters to Vertical Rails

B. Attach Monitor

6 of 15 or or or or or or or or

888-61-053-W-02 rev. F • 10/19

3

Wood Stud Installation

a

Drill 4 holes: 2 at stud and 2 at solid wall using appropriate bits.

b

Mounting T emplate

UP

Place template on wall so that it covers at least one wood stud and mark the mounting holes with a pencil.

7/32”

80mm

1/2” c

Insert wall anchors into wall (not wood stud).

d

Install top two screws leaving about a 1/2” of room between the head of the screw and the wall.

13mm

2x

1

2

3

1/2" diameter

1/2 pulg. de dia.

888-61-053-W-02 rev. F • 10/19

1x

1/4 - 20 x 1.5”

1x

8mm x 80mm

7 of 15

e

Using the wall plate keyholes, hang the lift assembly on the wall screws.

f

8 of 15

1x

1/4 - 20 x 1.5”

1x

8mm x 80mm

13mm

Attach lift assembly to wall using 1/4-20 screws and lag bolts. Tighten bolts with socket wrench and screw driver.

Install and tighten bottom two wall screws and securely tighten top screws. Be sure that the lift engine is level before tightening.

DO NOT OVER TIGHTEN.

CAUTION: When mounting to wood frame wall, one set of mounting holes must be located in the center of a wood stud no smaller than 2x4 inches (nominal). If in doubt, consult a local construction expert. Failure to heed this caution may result in equipment damage and personal injury

888-61-053-W-02 rev. F • 10/19

4

Solid Wall Installation

a

Place template on wall and mark the mounting holes with a pencil.

b

Drill 4 holes.

Mounting T emplate

UP

3/8”

80mm d

Install top two screws leaving about a 1/2” of room between the head of the screw and the wall.

c

Insert wall anchors into wall.

4x

13mm

2x

888-61-053-W-02 rev. F • 10/19 9 of 15

e

Using the wall plate keyholes, hang the lift assembly on the wall screws.

f

10 of 15

2x

13mm

Attach lift assembly to wall using lag bolts.

Tighten bolts with socket wrench and screw driver.

Install and tighten bottom two wall screws and securely tighten top screws. Be sure that the lift engine is level before tightening.

DO NOT OVER TIGHTEN.

888-61-053-W-02 rev. F • 10/19

5

Attach Rails To Lift Assembly

16x

2x

2x

4mm

888-61-053-W-02 rev. F • 10/19 11 of 15

6

Hang TV On The Lift Assembly

2x

12 of 15

NOTE: For safe and proper installation be sure to install the locking screw as shown.

888-61-053-W-02 rev. F • 10/19

7

Route Cables

CAUTION: Risk of electrical shock. To ensure safe use of this product, install power outlets or supplies outside of the horizontal rails.

Do not route electrical cords within the path of the horizontal rails. Use the below items to appropriately route your power, hdmi, and AV cables.

Be aware of pinch points when routing cables. Failure to heed this caution may result in equipment damage or personal injury.

888-61-053-W-02 rev. F • 10/19 13 of 15

Adjust your mounting solution to handle the added weight.

Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments are diffi cult and do not stay in the desired position, follow the instructions to loosen or tighten the tension to create a smooth, easy adjustment motion. Depending on your product and the adjustment, it may take several turns to notice a diff erence.

8

Adjustment Step

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.

Depending on your product and the adjustment, it may take many turns to notice a diff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. a

+

13mm

Increase Lift Strength

If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase

Lift Strength:

Decrease Lift Strength

If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease

Lift Strength:

14 of 15 888-61-053-W-02 rev. F • 10/19

b

10

°

Increase Friction

If this product moves too easily, then you'll need to increase friction:

Decrease Friction

If this product is too diffi cult to move, then you'll need to decrease friction:

Learn more about ergonomic computer use at: www.ergotron.com/ergonomics

For Warranty visit: www.ergotron.com/warranty

Para servicio, visite: www.ergotron.com

Para conocer los números telefónicos locales de atención al cliente, visite: http://contact.ergotron.com

www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

© 2015 Ergotron, Inc. All rights reserved.

888-61-053-W-02 rev. F • 10/19 15 of 15