WorkFit C

Single LCD Mount, LD

User's Guide

Includes

Constant Force ™

Technology

English

For the latest User Installation Guide please visit: www.ergotron.com

English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语 www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

888-24-143-W-02 rev.E • 12/18 1 of 14

Hazard Symbols

Review

These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the signi fi cance of the following Safety Hazards if encountered on the product or within the documentation. Children who are not able to recognize and respond appropriately to

Safety Alerts should not use this product without adult supervision!

Symbol Signal Word

NOTE

CAUTION

WARNING

ELECTRICAL

Level of Hazard

A NOTE indicates important information that helps you make better use of this product.

A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

A WARNING indicates either potential for property damage, personal injury, or death.

An Electrical indicates an impending electrical hazard which, if not avoided, may result in personal injury, fi re and/or death.

Safety

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or di ffi smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a di ff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Moving Parts Can Crush & Cut

2 of 14 888-24-143-W-02 rev.E • 12/18

Weight Capacity: 40 lbs. (18 kg)

Capacidad de soporte de peso: 40 lbs. (18 kg)

Capacité de poids: 40 lbs. (18 kg)

Tragkraft: 40 lbs. (18 kg)

Gewichtscapaciteit: 40 lbs. (18 kg)

Capacità di peso: 40 lbs. (18 kg)

許容重量:

40 lbs. (18 kg)

承重: 40 lbs. (18 kg)

허용 중량:

40 lbs. (18 kg) 2.6"- 8.5 (66 - 216 mm)

9.4" - 15.75" (239 - 400 mm)

5"

(127 mm)

20˚

10˚

A

B

C

D

6 - 16 lbs

(2.7-7.3 kg)

< 5 lbs

(2.25 kg)

< 2 lbs

(0.9 kg)

< 1.5 lbs

(0.68 kg)

A + B + C + D < 31 lbs (14 kg)

888-24-143-W-02 rev.E • 12/18

Release Brake to move riser.

Suelte el freno para mover el elevador.

Relâcher le frein pour déplacer la colonne montante.

Lösen Sie die Bremse, um eine Höhenverstellung vorzunehmen.

Zet de rem los om de staander te verplaatsen.

Rilasciare il freno per sollevare o abbassare il sostegno.

ライザーを動かすには、ストッパーを解除します。

释放锁定装置移动升降杆。

3 of 14

4

2

3

1

1x

A B C

1x

1x

M3 x 6mm

1x M5 x 8mm

2x

M6 x 22mm

2x

1x

2x

M6 x 16mm

4x

M4 x 10mm

D

1x

4x

6x

2x

M4 x 10mm

3

1

2

1x

A

1x

B

4x

4x

C

2x

D

1x 2x

4x

M5 x 8mm

1x

M5 x 22mm

1x

5mm

5-sided Security Wrench

Llave de seguridad pentagonal

Clef Allen de sécurité

Fünfkant-Inbusschlüssel

5-kantige veiligheidssleutel

Chiave pentagonale di sicurezza

5角固定用レンチ

5角安全扳手

5면 Security Wrench(안전 렌치)

14mm

4 of 14 888-24-143-W-02 rev.E • 12/18

1

1x

2

2x

3

4mm

2x

M6 x 16mm

2x

M6 x 22mm

888-24-143-W-02 rev.E • 12/18 5 of 14

7

6 of 14

4

5

4x

M4 x 10mm

4x

M4 x 10mm

1x

M5 x 8mm

3mm

0°

1x

M3 x 6mm

6

Release Brake to move riser.

Suelte el freno para mover el elevador.

Relâcher le frein pour déplacer la colonne montante.

Lösen Sie die Bremse, um eine Höhenverstellung vorzunehmen.

Zet de rem los om de staander te verplaatsen.

Rilasciare il freno per sollevare o abbassare il sostegno.

ライザーを動かすには、ストッパーを解除します。

释放锁定装置移动升降杆。

888-24-143-W-02 rev.E • 12/18

8 a c

3mm b d

5mm

5-sided wrench llave pentagonal

Clef Allen

Inbusschlüssel

5-kantige sleutel

Chiave a 5 lati

5 角レンチ

5角扳手

5면 렌치 e b

9 a 4x c

2x

NOTE: Center on bottom

NOTA: Centre por la parte inferior

REMARQUE : centrer la partie inférieure

HINWEIS: Richten Sie die Geräte mittig aus.

OPMERKING: Centreren op onderkant

NOTA. Centrare nella parte inferiore.

OBS: Mitten på underdelen

注：下部の中央

注意：底部居中

888-24-143-W-02 rev.E • 12/18 d

7 of 14

10 a b

3mm c

CAUTION:Do Not over tighten fasteners. Over-tightening may cause damage to fasteners.

11

5mm

5-sided wrench llave pentagonal

Clef Allen

Inbusschlüssel

5-kantige sleutel

Chiave a 5 lati

5 角レンチ

5角扳手

5면 렌치

8 of 14 888-24-143-W-02 rev.E • 12/18

12 a

2x

M5 x 8mm b c

5mm

5-sided wrench llave pentagonal

Clef Allen

Inbusschlüssel

5-kantige sleutel

Chiave a 5 lati

5 角レンチ

5角扳手

5면 렌치

13

2x a

M5 x 8mm b

5mm

5-sided wrench llave pentagonal

Clef Allen

Inbusschlüssel

5-kantige sleutel

Chiave a 5 lati

5 角レンチ

5角扳手

5면 렌치

888-24-143-W-02 rev.E • 12/18 9 of 14

14 a b

1x

M5 x 22mm

5mm

5-sided wrench llave pentagonal

Clef Allen

Inbusschlüssel

5-kantige sleutel

Chiave a 5 lati

5 角レンチ

5角扳手

5면 렌치

10 of 14 888-24-143-W-02 rev.E • 12/18

15

1x

2x

NOTE: Leave enough slack in cable to allow full range of motion.

Caution: To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury.

6x

888-24-143-W-02 rev.E • 12/18 11 of 14

16

Adjustment Step

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or di ffi does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.

Depending on your product and the adjustment, it may take many turns to notice a di ff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. a

14mm

Increase Lift Strength

If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase

Lift Strength:

Decrease Lift Strength

If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease

Lift Strength:

1 2

1

2

12 of 14 888-24-143-W-02 rev.E • 12/18

b

4mm

Increase Lift Strength

If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase

Lift Strength:

Decrease Lift Strength

If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease

Lift Strength: c

Increase Friction

If this product moves too easily, then you'll need to increase friction:

Decrease Friction

If this product is too di ffi then you'll need to decrease friction:

888-24-143-W-02 rev.E • 12/18 13 of 14

Learn more about ergonomic computer use at: www.ergotron.com/ergonomics

For Warranty visit: www.ergotron.com/warranty

For Service visit: www.ergotron.com

For local customer care phone numbers visit: http://contact.ergotron.com

www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

© 2015 Ergotron, Inc. All rights reserved. WorkFit ™ is a registered trademark of Ergotron, Inc.

WorkFit ™ is a registered trademark of Ergotron, Inc.

14 of 14 888-24-143-W-02 rev.E • 12/18