advertisement
8VHUV*XLGH
0RQLWRUDQG/DSWRS.LW
IRU:RUN)LW77/7/(7;DQG&RUQHU'HVN&RQYHUWHUV
(QJOLVK
)RUWKHODWHVW8VHU,QVWDOODWLRQ*XLGHSOHDVHYLVLWZZZHUJRWURQFRP
(QJOLVK(VSD³RO)UDQ©DLV'HXWVFK1HGHUODQGV,WDOLDQR7¾UN©H㡴㦻崭㻘幼 www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]
888-97-375-G-01 rev.G • 11/20 1 of 9
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or di ffi create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a di ff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Warning: Impact Hazard! Moving Parts can Crush and Cut.
Raise worksurface to top of vertical adjustment BEFORE removing equipment.
Failure to heed this warning may result in serious personal injury and or property damage!
WARNING
Impact Hazard!
Moving Parts can Crush and Cut.
Raise monitor to top of vertical adjustment
BEFORE removing.
Failure to heed this warning may result in serious personal injury or property damage!
822-635
Warning: Impact Hazard! Moving Parts can Crush and Cut.
Raise monitor to top of vertical adjustment before removing.
C
D
A
B
6 - 16 lbs
(2.7-7.3 kg)
< 10 lbs
(4.5 kg)
< 5 lbs
(2.25 kg)
5"
(127 mm)
20˚
5˚
A + B + C + D < WorkFit-T: 24.9 lbs (11.29 kg)
WorkFit-TL: 29.9 lbs (13.56 kg)
WorkFit-TLE: 29.9 lbs (13.56 kg)
WorkFit-TX: 29.9 lbs (13.56 kg)
WorkFit-Corner: 24.9 lbs (11.29 kg)
888-97-375-G-01 rev.G • 11/20 2 of 9
A
1
1x
2
1x
5
4
3
1x
4x
M6 x 25mm
4x
M6 x 20mm
4x
1x
4x
B
8x
C
1x 1x
D
1x
1x
2x
E F
M4 x 5mm
4x
M4 x 10mm
4x 4x
2x
M6 x 6mm
4mm
1x
2x
M4 x 10mm
1x
M4 x 10mm
888-97-375-G-01 rev.G • 11/20 3 of 9
1 a
WorkFit -T, TL, TLE
b
WorkFit -T Corner
b
WorkFit - TX
b c
4x
4mm
4x
M6 x 25mm c
4x
4mm
4x
M6 x 20mm c
4x
4mm
M6 x 20mm
4 of 9 888-97-375-G-01 rev.G • 11/20
2
4mm
4x
M6 x 6mm
3
4
1x
M4 x 5mm
1x
M4 x 5mm
2x
M4 x 10mm
4x
M4 x 10mm
4x
M4 x 10mm
5 of 9 888-97-375-G-01 rev.G • 11/20
5
&HQWHUWRWDOZLGWKRIPRXQWHG
HTXLSPHQWRQVWDQG
7RHQVXUHVWDELOLW\WKHGRFNLQJ
VWDWLRQ6+28/'127H[WHQG
RYHUWKHEDFNRIWKHWUD\
1x
4x
1x
6 of 9 888-97-375-G-01 rev.G • 11/20
6 127(/HDYHHQRXJKVODFNLQFDEOHWRDOORZIXOOUDQJHRIPRWLRQ
&DXWLRQ7RDYRLGWKHSRWHQWLDOWRSLQFKFDEOHVLWLVLPSRUWDQWWRIROORZWKHFDEOHURXWLQJLQVWUXFWLRQVLQWKLVPDQXDO
)DLOXUHWRIROORZWKHVHLQVWUXFWLRQVPD\UHVXOWLQHTXLSPHQWGDPDJHRUSHUVRQDOLQMXU\
1x
2x
6x
888-97-375-G-01 rev.G • 11/20 7 of 9
7
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or di ffi does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a di ff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. a
4mm
Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease
Lift Strength: b
Increase Friction
If this product moves too easily, then you'll need to increase friction:
Decrease Friction
If this product is too di ffi then you'll need to decrease friction:
888-97-375-G-01 rev.G • 11/20 8 of 9
5HDG\WRJHWPRYLQJRQDQDFWLYHZRUNVW\OH"&KHFNRXWZZZHUJRWURQFRPWLSVWRJHWVWDUWHG
/HDUQPRUHDERXWHUJRQRPLFFRPSXWHUXVHDWZZZHUJRWURQFRPHUJRQRPLFV www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]
)RU:DUUDQW\YLVLWZZZHUJRWURQFRPZDUUDQW\
)RU6HUYLFHYLVLWZZZHUJRWURQFRP
)RUORFDOFXVWRPHUFDUHSKRQHQXPEHUVYLVLWKWWSFRQWDFWHUJRWURQFRP k(UJRWURQ,QF$OOULJKWVUHVHUYHG
888-97-375-G-01 rev.G • 11/20 9 of 9
advertisement
Related manuals
advertisement