Installation

1 2

TITAN

™ Impact

Rotor

User Guide

3 4

Install sprinkler flush with ground.

Connect water supply to either bottom or side inlet.

Performance Data*

Standard Nozzle

Nozzle Pressure psi

Radius

(ft.)

1.5

(orange)

02.0

(red)

3.0

(black)

4.0

(blue)

6.0

(green)

30

40

50

50

30

40

50

40

50

30

40

30

40

50

30

32

35

36

33

37

40

35

39

41

38

41

42

39

43

45

Low Angle (LA) Nozzle

Nozzle Pressure psi

Radius

(ft.)

Flow

GPM

2.0LA

(grey)

30

40

50

30

23

24

25

27

1.8

2.0

2.2

3.7

4.0LA

(yellow)

40

50

30

32

4.3

4.8

* Precipitation rate data based on full-circle (360°).

Precip. in/h

0.33

0.33

0.34

0.49

0.46

0.45

4.2

5.1

5.8

6.5

7.5

2.9

3.6

5.0

3.8

2.3

2.0

2.2

2.5

Flow

GPM Precip. in/h

1.5

1.8

0.16

0.16

0.20

0.20

0.18

0.17

0.26

0.26

0.26

0.29

0.28

0.32

0.42

0.39

0.41

0.23

0.23

0.23

0.25

0.24

0.28

0.37

0.34

0.36

Precip. in/h

0.14

0.14

0.17

0.18

0.15

0.15

Precip. in/h

0.38

0.39

0.39

0.56

0.56

0.52

Screw included plug into unused inlet.

Fill hole with gravel covered by a layer of soil.

In cold climates, protect sprinkler from freeze damage by installing a drain valve to bottom inlet.

Ensure Even Coverage

To ensure that each area of your lawn receives the same amount of water (uniform coverage), install the nozzle indicated in the chart to the left to correspond with the full or part-circle spray pattern. Irritrol nozzles feature Matched

Precipitation Rates to allow sprinklers with different patterns to be zoned together, in which each sprinkler delivers matching amounts of water.

For new installations, avoid dry spots and areas of overwatering by spacing sprinklers so their patterns overlap.

Use the guidelines in the accompanying chart and position sprinklers as shown for optimum coverage.

Space sprinklers for head-to-head coverage.

!

©2020 Irritrol Systems • www.irritrol.com • Technical Support: 1-800-634-8873

WARNING: Cancer and Reproductive harm – www.P65Warnings.ca.gov.

For more information, please visit www.toro.com/CAProp65.

Patent: www.ttcopats.com

Irritrol

5825 Jasmine Street

Riverside, CA 92504

Form Number 373-0813 Rev. B

Operation

Match spray pattern to your layout

Adjust sprinkler to fit your layout by selecting full or part-circle spray patterns.

Full circle : Flip trip lever up to allow sprinkler to rotate

360° (see Figure 1 ).

Part circle : Flip trip lever down and adjust the sprinkler collars. The angle between the collar handles determines the arc the sprinkler will water (20° to 340°)

(see Figure 2 and 3 ).

Trip lever up

Figure 1 - Full Circle

Trip lever down

Trip lever down

90°

Figure 3 - Quarter Circle

Replace a Nozzle

1. With a screwdriver, remove the top cover cap

( Figure 4 ).

2. With needlenose pliers, remove the top cover

( Figure 5 ).

3. Pull the rotor arm aside to expose the nozzle

( Figure 6, A ).

4. Rotate the nozzle tab down to release the nozzle

( Figure 6, B ).

5. Remove the nozzle and replace with a new one.

6. Turn the nozzle tab clockwise to lock the new nozzle in place.

7. Push the top cover back into place.

8. Install the top cover cap.

180°

Figure 2 - Half Circle

Figure 4

Figure 5

Figure 6

Maintenance & Troubleshooting

• Do not use oil, grease, or pipe dope on sprinkler.

• Check sprinkler nozzle for debris.

• Check valve function.

• Check timer function.

Note : When using the orange or red low-flow nozzles, move Adjustment Spring to the Figure 7, B position for best operation.

Figure 7

Reduce Spray Distance

To reduce the spray distance (radius) up to 25%, with the sprinkler running, turn the spray reduction screw clockwise into the stream; turn counterclockwise to increase the spray radius (see Figure 8 ).

Figure 8

Nozzle Radius reduction screw