Sytech SYXTR16BT ALTAVOZ SERIE "MICROBEAT" 6", 10W, RMS / 80 PMPO, RECARGABLE, BT, MIC, LED, Owner Manual
Advertisement
Advertisement
WELCOME
Welcome to Sytech! Thank you for purchasing the new Portable speaker
Micro Beat SY-XTR16BT. Please read this manual carefully before operating your product and pay close attention to the precautions which are mentioned below. Store this user manual in a safe place for future reference
SAFETY INFORMATION AND WARNINGS
To prevent risk of fire or electric shock, avoid overloading wall outlets, extension cords, or Integral convenience receptacles.
Use suitable power sources - Plug the product into a suitable power source, as described in the operating instructions or as marked on the product.
The supply voltage should be the same as that indicated in the technical specifications and the appliance rating plate. If the socket outlets in your home are not suitable for the plug supplied with this unit check with a qualified electrician for replacement.
In order to disconnect the apparatus from the mains completely, switch off the outlet and remove the mains plug completely.
Do not bend, stretch or pull the supply cable in order to avoid electric shock.
Moisture and water
• Do not use this apparatus near water or moisture.
• Do not use this product near a bathtub, washbowl, kitchen sink, laundry tub, wet basement, near a swimming pool or anywhere else that water or moisture is present.
Heat sources and flames
• Batteries shall not be exposed to excessive heat such as sun
or fire.
• To prevent risk of fire or electric shock, avoid overloading wall outlets, extension cords, or integral convenience receptacles.
Servicing and repairs
• Refer all servicing to qualified service personnel.
• Servicing is required when the apparatus has been damaged
in any ways: such as liquid has been spilled or objects have
fallen into the apparatus; The apparatus has been exposed
to rain or moisture, does not operate normally, or has been
dropped. In case of any failure with the apparatus, contact
Sytech technical service center for a proper repair and
solution.
Warning
The normal function of the product may be disturbed by strong Electro-
Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in other location.
SAFETY INSTRUCTIONS
1) Read this Instruction Manual before you attempt to connect or operate the appliance.
2) Keep these instructions in good condition. Heed all warnings. Follow all instructions.
3) Save this Instruction Manual for future reference.
4) The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product. Use dry locations only.
5) No naked flame source, such as candles, should be placed on the product.
6) Children should be supervised to ensure that they do not play with the appliance.
7) Ventilation should not be impeded by covering the ventilation openings.
8) Ensure that the unit is plugged into 5V.1A AC adaptor. Using higher voltage may cause the unit to malfunction or even fire catching. Turn off the unit before unplugging it from power source to completely switch it off.
9) Do not plug/ unplug the power plug into/from an electrical outlet with wet hands.
10) Use replacement parts, which are specified by the manufacturer.
11) Install the unit in accordance with the manufacturer’s instructions.
12) Place the unit where there is good ventilation. Place the speaker on a flat, hard and stable surface. Do not expose to temperatures above
40°C. Allow at least 30 cm clearance from the rear and the top of the
unit as well as 5 cm from each side.
13) Press the buttons of the unit gently. Pressing them too hard can damage the unit.
14) Always ensure that the product is unplugged from the electrical outlet before moving or cleaning. Clean it with dry cloth only.
15) Unplug the product during lightning, storms or when it will not be used for long periods of time.
16) This product has no user serviceable parts. Do not try to repair this product yourself. Only qualified service personnel should perform the service. Contact Sytech technical service for a proper inspection and repair
17) NEVER let anyone, especially children, insert anything into the holes, slots or any other openings in the unit’s casing as this could result in a fatal electric shock.
18) Do not place the unit near TVs, speakers and other objects that generate strong magnetic fields.
NOTE: To disconnect the system completely if it’s not to be used for a long time, remove the AC adaptor plug from the wall outlet.
CONTROL PANEL & FUNCTIONS
1. Microphone input jack 6.3mm.
2. LED pilot light
3. Charging port (DC 5V.1A)
4. On/Off switch
5. 2.0 USB port
6. MP3 (Previous track) – FM (Previous FM station) –
Press and Hold to decrease the volume level
7. MP3 (Play / Pause) – FM (Automatic search).
Short press the “Play/Pause” button twice to connect the TWS mode.
Long press the “Play/Pause” button to disconnect the phone.
8. MP3 (Next track) – FM (Next FM station)
Press and hold to increase the volume level.
9. Mode button (MP3, FM, Bluetooth) – LED.
Short press the “M” button to switch the LED light effects.
Long press the “M” button to switch between the different functions.
Charging your speaker:
1. Connect the Micro USB cable into the Micro USB speaker port.
2. Connect the other end of the USB port to an external AC adaptor making sure the voltage does not exceed 5V-1Ah.
3. The red LED pilot light will go on indicating that the battery is charging.
4. Once the charging process is over, the red LED pilot light will go off.
Input modes:
Follow the below instructions to switch between Bluetooth, FM radio, and
USB input modes.
1. Press the “M” button on the main unit repeatedly to cycle between
Bluetooth, FM radio, and USB input modes.
Bluetooth connection:
To connect a smartphone or any other device to your speaker via
Bluetooth, follow the below steps:
1. Press the “M” button on the unit until you hear “Bluetooth”.
2. Enable the Bluetooth function on your smartphone, tablet or any other
Bluetooth device which you wish to connect to your speaker and search for “SY-XTR16BT”. Once found, select it to pair your external device to the speaker.
3. In the case you are asked to enter a code, please enter “0000”.
4. Once the speaker is connected to your external Bluetooth device, a sound will be heard confirming the pairing of the two devices.
5. Each time you switch the Speaker on and select the Bluetooth mode, the device will automatically pair and connect to the last device, unless the device has been un-paired on your external Bluetooth device.
6. Once the devices are paired up, press the Play/Pause button to start playback.
7. When receiving a call during Bluetooth playback, the audio will automatically stop playing. Once you hang up the call, the music will restore.
8. The volume output is affected by the volume level from the external audio source: For example, if you have paired your smartphone, you will need to adjust the volume level from your smartphone to avoid distortion.
To unpair the device from a Bluetooth connection with your speaker,
you need to disconnect and forget the device from your external
device.
USB function:
1. Press the “M” button on the unit until you hear “USB” or simply insert your USB pen drive into the USB port.
2. The first track will automatically start to play. Press the Play/ pause button to pause the track at any time.
3. Press the “Next” button to advance to the next track.
4. Press the “Previous” button to go back to the previous track.
FM Radio function:
1. Press the “M” button on the unit until you hear “FM”
2. Press the Play / Pause button to start the automatic scan.
3. Once the scan function has finalized, press the “Next” or “Previous” buttons to switch from one preset to the another.
Note: The position of the speaker is important for a good FM reception. If you are unable to find a desired radio station, move the party speaker to a different location and try to scan again.
TWS function:
1. To enjoy True Wireless audio sound “TWS”, you will need two identical units of SY-XTR16BT.
2. Connect one of the speakers to your external device via Bluetooth as indicated in the above section under “Bluetooth connection”.
3. Once your speaker is paired to your external device, switch on the second speaker and enter the Bluetooth mode.
4. Click twice on the “Play/Pause” (7) button on the second speaker until a “BEEP” sound is heard. Now your two speakers are connected to your external device.
5. Enjoy your track in a pure True wireless mode.
Mic Function:
1. Connect the external wired microphone to the jack input connector of
6.3mm.
(Wired microphone is included)
Accessories included:
1. Micro Beat Party speaker
2. Wired microphone, DC 5V Micro USB charging cable - USB 2.0 cable.
3. Instruction manual
Environment and Compliance:
The European directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.
To avoid possible hearing damage, do not listen at high audio volume for a long period of time.
TECHNICAL SPECIFICATIONS
Basic Specifications
•
High resistant material finishing
• 6-inch speakers.
•
FM tuner with pre-set memory stations
•
RGB lights integrated on the speaker
•
Microphone input 6.3 mm.
•
Integrated rechargeable lithium battery
• Charging time: 2 hours approx.
•
Playing time: 2-3 hours approx.
Bluetooth Specifications
• Bluetooth Version: V5.0 + EDR
•
Bluetooth Profiles: EDR, A2DP, AVRCP
• Bluetooth Pairing name: SY-XTR16BT
•
Compatible Audio Formats in Bluetooth: MP3/WMA
USB Specifications
• 2.0 USB Port (Max capacity : 64GB)
•
Compatible Audio Formats in USB: MP3/WMA
Charging voltage
•
Power: 5V.1A (Do not use any other higher voltage AC adaptor)
Technical Specifications
•
Output power: 10W.RMS max.
•
Output power PMPO: 80W
•
Rechargeable battery: 3.7V-1500mah
•
Bluetooth operating distance: 10 meters.
• SNR: ≥ 90dB
•
Frequency response: 200Hz ~ 13Khz.
• 1 way speaker: 1 x 6” 2.4 Ohms
Dimensions and weight:
•
Unit dimension : (LxWxH) : 16,3 x 20,8 x 30,5 cm.
•
Weight: 0,93 Kg.
• Above specifications are the specifications of SY-XTR16BT “Micro Beat
Series” and are for reference purpose only.
•
Due to continuous product development, specifications may be subject to change without prior notification.
• Do not expose to adverse weather conditions (Such as rain or high temperatures) as it can cause malfunctions
DECLARATION OF CONFORMITY
Manufacturer Name: Satyatrade S. L.
Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B84254763
Manufacturing country: China
Description: Party speaker Micro Beat
Sytech® SY-XTR16BT complies with the following directives:
RED Standard: Directive 2014/53/EU
ROHS Standard: Directive 2015/863/EU Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator www.sytech.es

Public link updated
The public link to your chat has been updated.
Advertisement