Autonics TK4H, TK4L, TK4M, TK4N, TK4SP, TK4W Instruction Manual

DRW170598AA
Temperature / Process Controller
※1. In case of TK4N/SP Series, option control selection and digital input will be limited due to number of terminals.
※2. " S" represents SSR drive output support models which SSRP function (standard ON/OFF, cycle, phase)
control are available. "C" represents selectable current and SSR drive output support models.
※3. Select "R" or "C" type in case of using heating&cooling control and "N" type in case of using standard control.
※4. Does not support in AC/DC voltage type model.
※5. Does not support in TK4N.
※6. The CT input model of TK4N is selectable only for standard model which has alarm output 1.
※7. The heating&cooling model of TK4N-1
has only alarm output 2.
※8. Only for TK4S-D
, OUT2 output terminal is used as DI-2 input terminal.
※9. 11Pin socket (PG-11, PS-11(N)) for TK4SP: sold separately.
※Shaded descriptions are upgraded or added functions from the before TK Series.
※The above specifications are subject to change and some models may be discontinued without notice.
※Be sure to follow cautions written in the instruction manual, user manual and the technical descriptions
(catalog, homepage).
RS485(B-)
RS485(A+)
+
+
mA
10
3
4
-
+
-
+
mA
6
OUT1:
250VAC 3A 1a
RESISTIVE LOAD
-
DI-1
Current
DC0/4-20mA
Load 500ΩMax.
SSR
11VDC±2V
20mA Max.
DI-1
3
-
-
4
mA
+
DI-2
2
+
5
6
DI-2
+
+
-
7
SOURCE
100-240VAC 50/60Hz 8VA
24VAC 50/60Hz 8VA
24-48VDC 5W
+
mA
-
-
RS485(A+)
14
15
OUT2:
Relay
250VAC 3A 1a
RESISTIVE LOAD
8
9
A
10
11
B
12
B'
+
24
15
25
16
8
26
17
9
27
18
+
+
mA
RTD TC
-
-
SOURCE
100-240VAC 50/60Hz 8VA
24VAC 50/60Hz 8VA
24-48VDC 5W
SENSOR
Dimensions
●TK4H Series
94.8
3
1
13
2
14
6
48
+
7
-
8
+
+
9
-
-
10
+
6
OUT1:
Relay
250VAC 3A 1a
RESISTIVE LOAD
21
+
+
mA
RTD TC
SENSOR
-
-
B'
DI-1
DI-2
Transfer Output
DC4-20mA
+
mA
-
Communication Output
Current
CT Transformer
0.0-50.0A
20
A
11
23
12
24
+
+
+
mA
B'
RTD TC
SENSOR
-
-
6
96
TK4N COVER (48×24mm)
44.6
(unit: mm)
64.5
1.5
●TK4S/SP (48 × 48mm) Series
※Insert the unit into a panel,
fasten the bracket by pushing with tools with a (-) driver.
(-) driver
64.5
41.5
3
70
1.7
22.5
RHA-COVER
(48×96mm, 96×48mm)
47.2
4
64
68.5
9.8
●Panel cut-out
●Bracket
TK4S, TK4SP Series
48.6
45
42
32.4
26.4
5
55
TK4M/W/H/L Series
31
20
46
15
21
12
23.9
10
56
13
13
86
※TK4N COVER is accessory.
22
18
64.5
1.5
91.5
6
72
45.2
48.6
(-) driver
6
96
RMA-COVER (72×72mm)
●TK4M Series
RSA-COVER (48×48mm)
48.4
91.5
●TK4L Series
TK4N Series
●Other Series
72.2
6
48
6.2
21.8
●TK4SP Series
13
11
(+) driver
+
B
Terminal cover (sold separately)
1. Measured value (PV) display part: RUN mode: It displays currently measured value (PV).
Setting mode: It displays the parameter.
2. Set value (SV) display part: RUN mode: It displays the set value (SV).
Setting mode: It displays the set value of the parameter.
3. Unit (℃/℉/%) indicator: It displays the unit set at display unit [UNIT] in parameter 3 group.
(In case of TK4N, % is not supported)
4. Manual control indicator: It turns ON during manual controlling.
5. Multi SV indicator: One of SV1 to 3 lamps will be ON in case of selecting multi SV function.
6. Auto tuning indicator: It flashes by 1 sec. when executing auto tuning.
7. Alarm output (AL1, AL2) indicator: It turns ON when the alarm output is ON.
8. Control output (OUT1, OUT2) indicator: It turns ON when the control output is ON.
※During cycle/phase controlling in SSRP function model (TK4 - 4S ), when MV is over 5.0%, it turns ON.
※To use current ouput, when MV is 0.0% in manual control, it turns OFF. Otherwise, it always turns ON.
When MV is over 3.0% in auto control, it turns ON and when MV is below 2.0%, it turns OFF.
9.
key: It is used when switching auto control to manual control.
※TK4N/S/SP do not have the
key. The
key operates switching simultaneously.
10.
key: It is used when entering parameter groups, returning to RUN mode, moving parameter,
saving the set value.
11. , , keys: It is used when entering the set value changing mode and moving or changing up/down digit.
12. Digital input key: When pressing + keys for 3 sec. at the same time, it operates the function
(RUN/STOP, alarm clear, auto tuning) set at digital input key [DI-K] in parameter 5 group.
13. PC loader port: It is the PC loader port for serial communication to set parameter and monitor with
DAQMaster installed in PC. Use this for connecting SCM-US (USB/Serial converter, sold separately).
※Insert the unit into a panel,
fasten the bolt with a (+) driver.
A
RS485(B-)
B
12
●TK4N (48 × 24mm) Series
Current
CT Transformer
0.0-50.0A
64.5
1.7
2
Installation
-
Communication Output
RS485(A+)
22
3
10
mA
48
●TK4S Series
48
9
Transfer
Output
DC4-20mA
+
RS485(B-)
DI-2
18
19
1.5
Digital Input
Non-contact,
Contact Input
17
OUT2:
Relay
250VAC 3A 1a
RESISTIVE LOAD
●TK4W Series
64.5
DI-1
RS485(A+)
DI-1
16
AL2 OUT:
250VAC 3A 1a
RESISTIVE LOAD
6
DI-1
Digital Input
Non-contact,
Contact Input
15
AL1 OUT:
250VAC 3A 1a
RESISTIVE LOAD
5
-
mA
12
OUT1:
Relay
250VAC 3A 1a
RESISTIVE LOAD
+
mA
21
14
Current
SSR
DC0/4-20mA
11VDC±2V
Load 500ΩMax. 20mA Max.
AL2 OUT:
250VAC 3A 1a
RESISTIVE LOAD
11
13
4
AL1 OUT:
250VAC 3A 1a
RESISTIVE LOAD
10
20
23
3
1
6
8
7
4
5
+
-
19
22
●TK4H, TK4W, TK4L
7
13
RS485(B-) 16
OUT1:
Communication Output
Relay
17 Current
250VAC 3A 1a
CT
Transformer
RESISTIVE LOAD
18 0.0-50.0A
48
+
6
SOURCE
100-240VAC 50/60Hz 8VA
24VAC 50/60Hz 8VA
24-48VDC 5W
OUT2:
Relay
250VAC 3A 1a
RESISTIVE LOAD
SSR
11VDC±2V
20mA Max.
Transfer +
mA
Output DC4-20mA
●TK4N Series
5
Current
DC0/4-20mA
Load 500Ω Max.
1
+
4
-
+
44.7
Digital Input
Non-contact,
Contact Input
+
-
mA
SOURCE
100-240VAC
50/60Hz 6VA
3
+
mA
AL2 OUT:
250VAC 0.5A 1a
RESISTIVE LOAD
Digital Input Current
SSR
Non-contact, DC0/4-20mA
11VDC±2V
Contact Input Load 500Ω Max. 20mA Max.
SOURCE
100-240VAC 50/60Hz 8VA
24VAC 50/60Hz 8VA
24-48VDC 5W
※ The input selection switch (TC, RTD/mV, V, mA) disappeared.
Select input type [IN-T] in parameter 3 group.
12
5
Current
DC0/4-20mA
Load 500Ω Max.
●TK4S
11
AL1 OUT:
250VAC 3A 1a
RESISTIVE LOAD
AL2 OUT:
250VAC 3A 1a
RESISTIVE LOAD
10
11
1
A
RLA-COVER (96×96mm)
D
B
3
94
C
(unit: mm)
Size
Model
TK4N
TK4S
TK4S (P)
TK4M
TK4H
TK4W
TK4L
A
B
C
D
55
65
65
90
65
115
115
37
65
65
90
115
65
115
45+00.6
45+00.6
45+00.6
68+00.7
45+00.6
92+00.8
92+00.8
22.2+00.3
45+00.6
45+00.6
68+00.7
92+00.8
45+00.6
92+00.8
86
9999 (4-digit)
TK
9
2
DI-2
DI-1
2
91.5
4
A
8
1
Current
SSR
DC0/4-20mA
11VDC±2V
Load 500ΩMax. 20mA Max.
Digital Input
Non-contact, contact input
9
AL1 :
Relay
250VAC 3A 1a
RESISTIVE LOAD
13
Digit
Item
B
7
SSR
11VDC±2V
20mA Max.
DI-1
+
1
2
DI-2
3
B
A
RTD
SENSOR
●TK4M
3.3
Size
※1
24VAC 50/60Hz, 24-48VDC
100-240VAC 50/60Hz
※
Standard
Alarm output 1+CT input 6
※
1
Heating&Cooling Alarm output 2 7
2 Standard
Alarm output 1+Alarm output 2
Standard
Alarm output 1+Digital input (DI-1, DI-2)
N D Heating&Cooling Digital input (DI-1, DI-2)
Standard
Alarm output 1+Transmission output
R
Heating&Cooling Transmission output
Standard
Alarm output 1+RS485 communication output
T
Heating&Cooling RS485 communication output
SP 1 Alarm output 1
1 Alarm output 1
2 Alarm output 1+Alarm output 2
S
M R Alarm output 1+Transmission output
W T Alarm output 1+RS485 communication output
H A Alarm output 1+Alarm output 2+Transmission output
L
B Alarm output 1+Alarm output 2+RS485 communication output
※
D Alarm output 1+Alarm output 2+Digital input (DI-1, DI-2) 8
N
DIN W48×H24mm
※9
SP
DIN W48×H48mm (11pin plug type)
S
DIN W48×H48mm (terminal block type)
M
DIN W72×H72mm
W
DIN W96×H48mm
H
DIN W48×H96mm
L
DIN W96×H96mm
※5
TC SENSOR
RTD B'
OUT2/AL1 OUT:
250VAC 3A 1a
RESISTIVE LOAD
+
+
8
4
Input/Output option
2
4
-
Communication Output
37.5
40.5
Power supply
R
Relay output
※
S 4 SSR drive output (standard ON/OFF, cycle control, phase control)
C
Current output or SSR drive output selectable
-
mA
Current Transformer
0.0-50.0A
CT
mA
+
TC
+
96
OUT1 control
※
output 2
Heating& R Relay output
Cooling C Current output or SSR drive output selectable
●TK4N
+
7
91.5
Unit Description
OUT2 control Standard N None ※Select in case of standard control (heating or cooling)
※
output 3
Transfer Output
DC4-20mA
+
16
1 4 R N
<Forked>
mA
36
TK 4 N
At room temperature range (23℃±5℃)
Thermocouple K, J, T, N, E type, below -100℃ / Thermocouple L, U, PLⅡ, Cu50Ω, DPt 50Ω:
(PV ±0.3% or ±2℃, select the higher one) ±1-digit
Thermocouple C, G, R, S type, below 200℃: (PV ±0.3% or ±3℃, select the higher one)±1-digit
Thermocouple B type, below 400℃: there is no accuracy standards.
Out of room temperature range
RTD Cu50Ω, DPt50Ω: (PV ±0.5% or ±3℃, select the higher one) ±1-digit
Thermocouple R, S, B, C, G type: (PV ±0.5% or ±5℃, select the higher one) ±1-digit
Others, below -100℃: within ±5℃
In case of TK4SP Series, ±1℃ will be added to the degree standard.
※2: The weight includes packaging. The weight in parenthesis is for unit only.
※Environment resistance is rated at no freezing or condensation.
-
B'
-
5
4
+
21.8
Ordering Information
※1:
Max.
5.8mm
-
45
1. W
hen connecting the power input and relay output, use AWG 20 (0.50mm2) cable or over and tighten
the terminal screw with a tightening torque of 0.74~0.90N m.
When connecting the sensor input and communication cable without dedicated cable, use AWG 28~16
cable or over and tighten the terminal screw with a tightening torque of 0.74~0.90N m.
Failure to follow this instruction may result in fire or malfunction due to contact failure.
2. U
se the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage.
3. U
se dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in electric shock or fire.
4. D
o not use the unit in the place where flammable/explosive/corrosive gas, humidity, direct sunlight,
radiant heat, vibration, impact, or salinity may be present.
Failure to follow this instruction may result in fire or explosion.
5. K
eep metal chip, dust, and wire residue from flowing into the unit.
Failure to follow this instruction may result in fire or product damage.
Min.
3.0mm
+
-
44.8
Caution
b
+
mA
mA
+
6
67.5
Warning
1. F
ail-safe device must be installed when using the unit with machinery that may cause serious injury
or substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles,
railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in fire, personal injury, or economic loss.
2. Install on a device panel to use.
Failure to follow this instruction may result in electric shock.
3. D
o not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in electric shock or fire.
4. C
heck 'Connections' before wiring.
Failure to follow this instruction may result in fire.
5. D
o not disassemble or modify the unit.
Failure to follow this instruction may result in electric shock or fire.
a
OUT2:
SSR
Current
Relay
11VDC±2V DC0/4-20mA
250VAC 3A 1a
RESISTIVE LOAD 20mA Max. Load 500ΩMax.
-
OUT1:
Current
SSR
Relay
DC0/4-20mA
11VDC±2V 250VAC 3A 1a
Load 500ΩMax. 20mA Max. RESISTIVE LOAD
<Round>
44.9
※The symbols used on the product and instruction manual represent the following
symbol represents caution due to special circumstances in which hazards may occur.
Max.
5.8mm
22
※Safety considerations are categorized as follows.
Warning Failure to follow these instructions may result in serious injury or death.
Caution Failure to follow these instructions may result in personal injury or product damage.
Min.
3.0mm
36.3
※Please observe all safety considerations for safe and proper product operation to avoid hazards.
b
b
3.5
Safety Considerations
a
a
11.6
Thank you for choosing our Autonics product.
Please read the following safety considerations before use.
●TK4SP
7.9
INSTRUCTION MANUAL
Connections
※Standard model has shaded terminals only.
※When the operation mode of heating&cooling OUT2 relay output model is heating or cooling control, the
OUT2 is usable as alarm output 3 (except TK4N Series).
※When the operation mode of heating&cooling OUT2 current output model is heating or cooling control, the
OUT2 is usable as transmission output 2.
※Use teminals of size specified below.
24
TK4 SERIES
TK4N
TK4SP
TK4S
TK4M
TK4W
TK4H
TK4L
100-240VAC 50/60Hz
24VAC 50/60Hz, 24-48VDC
90 to 110% of rated voltage
Max. 6VA
Max. 8VA
Max. 8VA (24VAC 50/60Hz), max. 5W (24-48VDC)
7-segment (PV: red, SV: green), other display part (green, yellow, red) LED method
4.5×7.2mm 7.0×14.0mm
9.5×20.0mm 8.5×17.0mm 7.0×14.6mm 11.0×22.0mm
3.5×5.8mm 5.0×10.0mm
7.5×15.0mm 6.0×12.0mm 6.0×12.0mm 7.0×14.0mm
JPt 100Ω, DPt 100Ω, DPt 50Ω, Cu 100Ω, Cu 50Ω, Nikel 120Ω (6 types)
K, J, E, T, L, N, U, R, S, B, C, G, PLII (13 types)
·Voltage: 0-100mVDC , 0-5VDC , 1-5VDC , 0-10VDC (4 types)
·Current: 0-20mA, 4-20mA (2 types)
※1
RTD
·At room temperature (23℃ ±5℃): (PV ±0.3% or ±1℃, select the higher one) ±1-digit
·Out of room temperature ranges: (PV ±0.5% or ±2℃, select the higher one) ±1-digit
Thermcouple
In
case
of
TK4SP
Series,
±1℃
will
be
added.
Display
·At room temperature (23℃ ±5℃): ±0.3% F.S. ±1-digit
accuracy Analog
·Out of room temperature ranges: ±0.5% F.S. ±1-digit
CT input
±5% F.S. ±1-digit
Relay
OUT1, OUT2: 250VAC 3A 1a
Control
SSR
Max. 11VDC ±2V 20mA
output
Current
DC4-20mA or DC0-20mA selectable (resistance load: max. 500Ω)
Alarm output Relay
AL1, AL2: 250VAC 3A 1a ※TK4N AL2: 250VAC 0.5A, 1a (max. 125VA), TK4SP has only AL1
Transmission
DC4-20mA (resistance load: max. 500Ω, output accuracy: ±0.3% F.S.)
Option
output
Communication RS485 communication output (Modbus RTU)
CT
0.0-50.0A (primary heater current reading range) ※CT ratio is 1/1000 (except TK4SP)
·Contact input: ON - max. 2kΩ, OFF - min. 90kΩ
Option
·Non-contact input: ON - residual votage max. 1.0VDC , OFF - leakage current max. 0.1mA
input
Digital input
·Outflow current: approx. 0.5mA per input
※TK4S/M: 1 (TK4S-D
: 2, TK4SP: none), TK4N/H/W/L: 2 (except TK4SP)
Control Heating, Cooling
ON/OFF, P, PI, PD, PID control mode
method Heating&Cooling
Hysteresis
·RTD/Thermcouples: 1 to 100℃/℉ (0.1 to 100.0℃/℉) variable ·Analog: 1 to 100-digit
Proportional band (P)
0.1 to 999.9℃/℉ (0.1 to 999.9%)
Integral time (I)
0 to 9999 sec
Derivative time (D)
0 to 9999 sec
·Relay output, SSR drive output: 0.1 to 120.0 sec
Control period (T)
·Current output+SSR drive output: 1.0 to 120.0 sec
Manual reset value
0.0 to 100.0%
Sampling period
50ms
Dielectric strength
2,000VAC 50/60Hz for 1 min (between power source terminal and input terminal)
Vibration
0.75mm amplitude at frequency of 5 to 55Hz (for 1 min) in each X, Y, Z direction for 2 hours
·OUT1/OUT2: min. 5,000,000 operations,
Mechanical
Relay
·AL1/AL2: min. 20,000,000 operations (TK4H/W/L: min. 5,000,000 operations)
life cycle
Electrical
OUT1/OUT2, AL1/AL2: min. 100,000 operations
Insulation resistance
Over 100MΩ (at 500VDC megger)
Noise immunity
Square shaped noise by noise simulator (pulse width 1㎲) ±2kV R-phase, S-phase
Memory retention
Approx. 10 years (non-volatile semiconductor memory type)
Environ Ambient temp. -10 to 50℃, storage: -20 to 60℃
-ment
Ambient humi. 35 to 85%RH, storage: 35 to 85%RH
Protection
IP65 (front panel) ※TK4SP: IP50 (front panel)
Double insulation or reinforced insulation
Insulation type
(mark: , dielectric strength between the measuring input part and the power part : 2kV)
Approval
Approx. 140g Approx. 130g Approx. 150g Approx. 210g Approx. 211g
Approx. 294g
※2
Weight
(approx. 70g) (approx. 85g) (approx. 105g) (approx. 140g) (approx. 141g)
(approx. 198g)
28.8
High Accuracy PID Temperature Controller
Specifications
Series
AC voltage
Power
supply
AC/DC voltage
Allowable voltage range
AC voltage
Power
consumption AC/DC voltage
Display method
Character PV (W×H)
size
SV (W×H)
RTD
Input
Thermcouple
type
Analog
Flow Chart for Setting Group
Parameter Mask
Run mode
Press any key among
,
,
once.
PASS ※1
When PW is valid
3 sec
2 sec
PASS ※1
※2
※2
PASS ※1
When PW
is valid
PARU※3
H-MV
Heating MV
Monitoring
PAR1
PAR2
Control output RUN/STOP[R-5]
Set the
set value
SV
Set user parameters
in DAQMaster
SV will be automatically
saved after 5 sec.
※2
PAR3
Auto-tuning RUN/STOP[AT]
1.5 sec
1.5 sec
C-MV
Cooliing MV
Monitoring
PAR4
Input type[IN-T]
PAR5
Alarm output1operation mode[AL-1]
1.5 sec
PAR2
AT
H-P
C-P
After applying mask
PAR2
H-P
H-I
H-D
1.5 sec
Heating proportional band[H-P]
Sensor temperature unit[UNIT]
Alarm output1 option[AL!T]
Digital input key[DI-K]
Heater current monitoring[CT-A]
Cooling proportional band[C-P]
Analog low-limit input value[L-RG]
Alarm output1 hysteresis[A!HY]
DI-1 input terminal function[DI-1]
Alarm output1 low-limit set value[AL!L]
Heating integral time[H-I]
Analog high-limit input value[H-RG]
Alarm1 N.O./N.C.[A!N]
DI-2 input terminal function[DI-2]
Alarm output1 high-limit set value[AL!H]
Cooling integral time[C-I]
Scaling decimal point[DOT]
Alarm1 ON delay time[A!ON]
Manual control, initial MV[ItMV]
Alarm output2 low-limit set value[AL@L]
Heating derivative time[H-D]
Low-limit scale value[L-SC]
Alarm1 OFF delay time[A!OF]
Manual control, preset MV[PrMV]
Alarm output2 high-limit set value[AL@H]
Cooling derivative time[C-D]
High-limit scale value[H-SC]
Alarm output2 operation mode[AL-2]
Sensor error, MV[ErMV]
Alarm output3 low-limit set value[AL#L]
Dead_overlap band[DB]
Display unit[dUNT]
Alarm output2 option[AL@T]
Control stop, MV[StMV]
Alarm output3 high-limit set value[AL#H]
Manual reset[REST]
Input correction[IN-B]
Alarm output2 hysteresis[A@HY]
Control stop, alarm output[StAL]
SV-0 set value[SV-0]
Heating hysteresis[hHYS]
Input digital filter[MAvF]
Alarm 2 N.O./N.C.[A@N]
User level[USER]
SV-1 set value[SV-1]
Heating OFF offset[hOST]
SV low-limit[L-SV]
Alarm 2 ON delay time[A@ON]
SV setting lock[LcSV]
SV-2 set value[SV-2]
Cooling hysteresis[cHYS]
SV high-limit[H-SV]
Alarm 2 OFF delay time[A@OF]
Parameter 1group lock[LcP1]
Cooling OFF offset[cOST]
Control output operation mode[O-FT] Alarm output3 operation mode[AL-3]
Parameter 2group lock[LcP2]
MV low-limit[L-MV]
Control type[C-MD]
Alarm output3 option[AL#T]
Parameter 3group lock[LcP3]
MV high-limit[H-MV]
Auto-tuning mode[AtT]
Alarm output3 hysteresis[A#HY]
Parameter 4group lock[LcP4]
RAMP-up change rate[RAMU]
OUT1 control output selection[OUT1]
Alarm 3 N.O./N.C.[A#N]
Parameter 5group lock[LcP5]
RAMP-down change rate[RAMD]
OUT1 SSR drive output type[O!SR]
Alarm 3 ON delay time[A#ON]
Password setting[PWD]
RAMP time unit[rUNT]
OUT1 current output range[O!MA]
Alarm 3 OFF delay time[A#OF]
OUT2 control output selection[OUT2]
LBA time[LBaT]
OUT2 current output range[O@MA]
LBA band[LBaB]
Heating control time[H-T]
Analog trans. output 1 mode[AoM1]
Cooling control time[C-T]
Trans. output 1 low-limit value[FsL1]
Trans. output 2 high-limit value[FsH2]
Comm. address[ADRS]
PAR1
AL!L
AL!H
Input Types and Range
Decimal point
Display
1
KCaH
K (CA)
0.1
KCaL
1
JIcH
J (IC)
0.1
JIcL
1
ECrH
E (CR)
0.1
ECrL
1
TCcH
T (CC)
0.1
TCcL
B (PR)
1
B PR
Thermocouple
R (PR)
1
R PR
S (PR)
1
S PR
N (NN)
1
N NN
C (TT)※1
1
C TT
G (TT)※2
1
G TT
1
LIcH
L (IC)
0.1
LIcL
1
UCcH
U (CC)
0.1
UCcL
Platinel II
1
PLII
Cu 50Ω
0.1
CU 5
Cu 100Ω
0.1
CU10
1
JPtH
JPt 100Ω
0.1
JPtL
RTD
DPt 50Ω
0.1
DPt5
1
DPtH
DPt 100Ω
0.1
DPtL
Nickel 120Ω 1
NI12
0-10V
AV1
0-5V
AV2
Voltage
1-5V
AV3
Analog
0-100mV
AMV1
0-20mA
AMA1
Current
4-20mA
AMA2
※1: C (TT): Same temperature sensor as former W5 (TT)
※2: G (TT): Same temperature sesnor as former W (TT)
Input range (℉)
-328 to 2463
-199.9 to 999.9
-328 to 1472
-199.9 to 999.9
-328 to 1472
-199.9 to 999.9
-328 to 752
-199.9 to 752.0
32 to 3272
32 to 3182
32 to 3182
-328 to 2372
32 to 4172
32 to 4172
-328 to 1652
-199.9 to 999.9
-328 to 752
-199.9 to 752.0
32 to 2534
-199.9 to 392.0
-199.9 to 392.0
-328 to 1202
-199.9 to 999.9
-199.9 to 999.9
-328 to 1202
-199.9 to 999.9
-112 to 392
When power is supplied, whole display parts flash for 1 sec. Afterwards, model name and input sensor type
will be flash twice and then in enters into RUN mode.
① Whole display part
② Model type display
③ Input type display twice
④ Run mode
Set Value (SV) Setting
,
,
You can set the temperature to control with
keys.
Set range is within SV low-limit value [L-SV] to SV high-limit value [H-SV].
Ex) In case of changing set temperature from 210℃ to 250℃
Press any key among
①
②
,
,
in RUN mode
to enter into SV setting
mode.
Last digit (100 digit) on
SV display part flashes.
④
Press
key to move digit.
(100→ 10¹→
10²→10³→ 100)
Description
OFF
No alarm output
DVCC
Deviation
high-limit
alarm
]]DV
Deviation
low-limit
alarm
Deviation
high/low-limit
alarm
CDV]
Deviation
high/low-limit
reserve alarm
PVCC
Absolute
value highlimit alarm
OFF
H
OFF H
ON
ON
If deviation between PV and SV
as high-limit is higher than set
SV
PV
PV
SV
value of deviation temperature,
100℃ 110℃
90℃ 100℃
the alarm output will be ON.
High deviation: Set as 10℃ High deviation: Set as -10℃
OFF
H
ON
H OFF If deviation between PV and SV
ON
PV
SV
90℃ 100℃
Low deviation: Set as 10℃
as low-limit is higher than set
SV
PV
value of deviation temperature,
100℃ 110℃
Low deviation: Set as -10℃ the alarm output will be ON.
If deviation between PV and
SV as high/low-limit is higher
than set value of deviation
PV
SV
PV
90℃ 100℃
120℃
temperature, the alarm output
Low deviation : Set as 10℃ , High deviation : Set as 20℃ will be ON.
ON
H
OFF H
OFF
H
ON
H OFF
ON
PV
SV
PV
90℃ 100℃
120℃
Low deviation : Set as 10℃ , High deviation : Set as 20℃
OFF H
ON
OFF
H
If deviation between PV and
SV as high/low-limit is lower
than set value of deviation
temperature, the alarm output
will be OFF.
ON
If PV is higher than the absolute
PV
SV
SV
PV
value, the output will be ON.
90℃ 100℃
100℃ 110℃
Absolute-value: Set as 90℃ Absolute-value: Set as 110℃
ON
H
OFF
ON
H OFF
]]PV
Absolute
value low-limit
alarm
LBA
Loop break
alarm
-
It will be ON when it detects
loop break.
SBA
Sensor break
alarm
It will be ON when it detects
sensor disconnection.
If PV is lower than the absoulte
PV
SV
SV
PV
value, the output will be ON.
90℃ 100℃
100℃ 110℃
Absolute-value: Set as 90℃ Absolute-value: Set as 110℃
Heater break
HBA
alarm
※H: Alarm output hysteresis[ A .HY]
It will be ON when CT detects
heater break.
●Alarm option
Mode
Name
Description
AL-A Standard alarm If it is an alarm condition, alarm output is ON. If it is a clear alarm condition, alarm output is OFF.
AL-B Alarm latch
Press
key to save
the set value.
If there is no additional
key operations in 3 sec,
the changed SV is
automatically saved.
+
+
Press
to reset all parameters in memory to default value.
Set [INIT] parameter to 'YES' to reset all parameters.
In case password function is on, it is required to enter valid password to reset parameters.
Password is also reset.
SV
Parameter
0
Factory default
PASS
0001
●Parameter 1 group [ PAR1 ]
Parameter Factory default Parameter Factory default Parameter Factory default Parameter Factory default
R-S
SV-N
CT-A
AL!L
RUN
SV-0
)0
1550
AL!H
AL@L
AL@H
AL#L
1550
1550
1550
1550
AL#H
SV-0
SV-1
SV-2
1550
0000
0000
0000
SV-3
0000
Parameter Factory default Parameter Factory default Parameter Factory default Parameter Factory default
AT
H-P
C-P
H-I
C-I
OFF
01)0
01)0
0000
0000
H-D
C-D
DB
REST
hHYS
0000
0000
0000
05)0
002
hOST
cHYS
cOST
L-MV
H-MV
000
002
000
`0)0
10)0
RAMU
RAMD
rUNT
000
000
MIN
Alarm latch
AL-D and standby
sequence 1
Standby
AL-E sequence 2
sequence 2
IN-T
UNIT
L-RG
H-RG
DOT
L-SC
KCaH
?C
0)00
1)00
)0
00)0
H-SC
dUNT
IN-B
MAvF
L-SV
H-SV
10)0
?/O
0000
00)1
-200
1350
O-FT
C-MD
AtT
OUT1
HEAT
H-C
PID
pP
TUN1
CURR
O!SR
O!MA
OUT2
O@MA
H-T
C-T
STND
4-20
CURR
4-20
02)0 (Relay)
00@0 (SSR)
●Parameter 4 group [ PAR4 ]
-
AL-F and standby
Parameter Reset
A@HY
Alarm operation
Alarm latch
-1999 to 9999
(Display point will be changed
according to decimal point position.)
A!HY
-
Standby
,
Press
key to raise
or lower the set value.
IN-B
Name
AL-C sequence 1
③
cHYS
Mode
Initial Display When Power ON
Input range (℃)
-200 to 1350
-199.9 to 999.9
-200 to 800
-199.9 to 800.0
-200 to 800
-199.9 to 800.0
-200 to 400
-199.9 to 400.0
0 to 1800
0 to 1750
0 to 1750
-200 to 1300
0 to 2300
0 to 2300
-200 to 900
-199.9 to 900.0
-200 to 400
-199.9 to 400.0
0 to 1390
-199.9 to 200.0
-199.9 to 200.0
-200 to 650
-199.9 to 650.0
-199.9 to 600.0
-200 to 650
-199.9 to 650.0
-80 to 200
hHYS
Alarm
Comm. write[COMW]
Input type
SV-0
Auto-tunning
]DVC
3 sec
●Password input parameter
Factory default
Parameter Factory default Parameter Factory default Parameter Factory default Parameter Factory default
PAR2
Auto-tuning measures the control subject's thermal characteristics and thermal response rate, and then
determines the necessary PID time constant. Application of the PID time constant realizes fast response and
high precision temperature control. (when setting control type [C-MD] is set as PID, it is displayed.)
Set [AT] parameter to [ON] in parameter 2 group to start auto-tuning. To stop auto-tuning, change the set as [OFF].
(It maintains P, I, D values of before auto-tuning.)
If sensor break error [OPEN] occurs during auto-tuning, it stops this operation. If the measured temperature is
over or below the input range, it operates continuously.
During auto-tuning operation, whole parameters are only available to check.
Comm. response waiting time[RSwT]
3 sec
Parameter
●Parameter 2 group [ PAR2 ]
The above is setting user parameter group in the DAQMaster with alarm output 1 low-limit value [AL!L], alarm output 1
high-limit value [AL!H], SV-0 set value [SV-0] parameter of parameter 1 group, heating hysteresis[hHYS],
cooling hysteresis [cHYS] parameters of parameter 2 group, input correction [IN-B] parameter of parameter 3
group, alarm output 1 hysteresis [A!HY], alarm output 2 hysteresis [A@HY] parameters of parameter 4 group.
Comm. parity bit[PRTY]
Comm. stop bit[STP]
Factory Default
●SV setting group [ SV ]
●Parameter 3 group [ PAR3 ]
PARU
Comm. speed[BPS]
3 sec
C-D
Run mode
Trans. output 2 low-limit value[FsL2]
3 sec
H-D
This function is able to set the frequently used parameters to the user parameter group. You can quickly and
easily set parameter settings. User parameter group can have up to 30 parameters in the integrated device
management program (DAQMaster).
For more information, refer to the DAQMaster user manual.
Visit our website (www.autonics.com) to download the DAQmaster program and the user manual.
Analog trans. output 2 mode[AoM2]
3 sec
C-I
●Alarm operation
Trans. output 1 high-limit value[FsH1]
※Hold the
key over 2 sec in RUN mode to enter into setting mode.
※Hold the
key for 1.5 sec while in setting mode to move to other
parameter group.
※Hold the
key over 3 sec while in setting mode to return to RUN mode.
※Press the
key at the lowest level of parameter to move parameter
group screen and press
,
key to move to other parameter group.
※If there is no additional key operation within 30 sec after entering into setting
mode, it will be automatically returned to RUN mode and previous set value
will be remained.
※The not-shaded parameters may not be displayed by other parameters
setting, parameter mask setting.
H-I
User Parameter Group [ PARU] Setting
Multi SV Number[SV-N]
※1. P
ASS parameter will be displayed only when password is set.
It is not displayed when purchasing the unit since default
SV-3 set value[SV-3]
password is set to 0000.
If password is not valid, the screen will be shifted to password
code required window.
Press any key among
,
,
to return to password
entering window. Press
key to return to RUN mode.
In case you forget password, contact Autonics after checking
password code.
※2. T
K4N/S/SP do not have
key.
key replaces
key.
※3. It is displayed when setting user parameter group
in the integrated device management program (DAQMaster).
Before applying mask
The above is masking auto tuning [AT], cooling proportional band [C-P], cooling integral time [C-1],
cooling derivative time [C-D] parameters in parameter 2 group.
Multi SV[MtSV]
1.5 sec
This function is able to hide unnecessary parameters to user environment or less frequently used parameters in
parameter group. You can set this in the integrated device management program (DAQmaster).
Masked parameters are not only displayed. The set value of masked parameters are applied.
For more information, refer to the DAQMaster user manual.
Visit our website (www.autonics.com) to download the DAQmaster program and the user manual.
If it is an alarm condition, alarm output is ON and maintains ON status.
First alarm condition is ignored and from second alarm condition, standard alarm
operates. When power is supplied and it is an alarm condition, this first alarm
condition is ignored and from the second alarm condition, standard alarm operates.
If it is an alarm condition, it operates both alarm latch and standby sequence. When
power is supplied and it is an alarm condition, this first alarm condition is ignored and
from the second 1alarm condition, alarm latch operates.
First alarm condition is ignored and from second alarm condition, standard alarm
operates. When re-applied standby sequence and if it is alarm condition, alarm output
does not turn ON. After clearing alarm condition, standard alarm operates.
Basic operation is same as alarm latch and standby sequence1. It operates not only
by power ON/OFF, but also alarm set value, or alarm option changing. When reapplied standby sequence and if it is alarm condition, alarm output does not turn ON.
After clearing alarm condition, alarm latch operates.
※Condition of re-applied standby sequence for standby sequence 1, alarm latch and standby sequence 1: Power ON
Condition of re-applied standby sequence for standby sequence 2, alarm latch and standby sequence 2: Power ON,
changing set temperature, alarm temperature [AL1, AL2] or alarm operation [AL-1, AL-2], switching STOP mode
to RUN mode.
Parameter Factory default Parameter Factory default Parameter Factory default Parameter Factory default
AL-1
AL!T
A!HY
A!N
A!ON
A!OF
AL-2
AL@T
A@HY
DVCC
AL-A
001
NO
0000
0000
]]DV
AL-A
001
A@N
A@ON
A@OF
AL-3
AL#T
A#HY
A#N
A#ON
A#OF
NO
0000
0000
OFF
AL-A
001
NO
0000
0000
LBaT
LBaB
AoM1
FsL1
FsH1
AoM2
FsL2
FsH2
ADRS
0000
002
PV
-200
1350
PV
-200
1350
01
BPS
PRTY
STP
RSWT
COMW
96
NONE
2
20
EnA
●Parameter 5 group [ PAR5 ]
Parameter Factory default Parameter Factory default Parameter Factory default Parameter Factory default
MtSV
DI-K
DI-1
DI-2
ItMV
1
STOP
OFF
OFF
AUTO
PrMV
ErMV
StMV
StAL
USER
00)0
00)0
00)0
CONT
STND
LcSV
LcP1
LcP2
LcP3
LcP4
OFF
OFF
OFF
OFF
OFF
LcPS
PWD
OFF
0000
※Shaded parameters are for the heating&cooling model.
User Manual
For the detail information and instructions, please refer to user manual and user manual for communication,
and be sure to follow cautions written in the technical descriptions (catalog, homepage).
Visit our homepage (www.autonics.com) to download manuals.
Comprehensive Device Management Program[DAQMaster]
DAQMaster is a comprehensive device management software for setting parameters and monitoring
processes. DAQMaster can be downloaded from our website at www.autonics.com.
Item
System
Operations
Memory
Hard disk
VGA
Others
Minimum specifications
IBM PC compatible computer with Pentium Ⅲ or above
Windows 98/NT/XP/Vista/7/8/10
256MB+
1GB+ of available hard disk space
Resolution: 1024×768 or higher
RS232C serial port (9-pin), USB port
Cautions during Use
1. Follow instructions in 'Cautions during Use'. Otherwise, It may cause unexpected accidents.
2. Check the polarity of the terminals before wiring the temperature sensor.
For RTD temperature sensor, wire it as 3-wire type, using cables in same thickness and length.
For thermocouple (CT) temperature sensor, use the designated compensation wire for extending wire.
3. Keep away from high voltage lines or power lines to prevent inductive noise.
In case installing power line and input signal line closely, use line filter or varistor at power line and shielded
wire at input signal line.
Do not use near the equipment which generates strong magnetic force or high frequency noise.
4. Do not apply excessive power when connecting or disconnecting the connectors of the product.
5. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the
power.
6. Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature controller.
7. When changing the input sensor, turn off the power first before changing.
After changing the input sensor, modify the value of the corresponding parameter.
8. 24VAC, 24-48VDC power supply should be insulated and limited voltage/current or Class 2, SELV power
supply device.
9. Do not overlapping communication line and power line.
Use twisted pair wire for communication line and connect ferrite bead at each end of line to reduce the effect
of external noise.
10. Make a required space around the unit for radiation of heat.
For accurate temperature measurement, warm up the unit over 20 min after turning on the power.
11. Make sure that power supply voltage reaches to the rated voltage within 2 sec after supplying power.
12. Do not wire to terminals which are not used.
13. This unit may be used in the following environments.
①Indoors (in the environment condition rated in 'Specifications')
②Altitude max. 2,000m
③Pollution degree 2
④Installation category II
Major Products
Photoelectric Sensors
Temperature Controllers
Fiber Optic Sensors
Temperature/Humidity Transducers
Door Sensors
SSRs/Power Controllers
Door Side Sensors
Counters
Area Sensors
Timers
Proximity Sensors
Panel Meters
Pressure Sensors
Tachometer/Pulse (Rate) Meters
Rotary Encoders
Display Units
Connector/Sockets
Sensor Controllers
Switching Mode Power Supplies
Control Switches/Lamps/Buzzers
I/O Terminal Blocks & Cables
Stepper Motors/Drivers/Motion Controllers
Graphic/Logic Panels
Field Network Devices
Laser Marking System (Fiber, CO₂, Nd: YAG)
Laser Welding/Cutting System
http://www.autonics.com
HEADQUARTERS:
18, Bansong-ro 513beon-gil, Haeundae-gu, Busan,
South Korea, 48002
TEL: 82-51-519-3232
E-mail: [email protected]
DRW170598AA
">